We present an efficient graphene-based photodetector with two Fabri-Pérot cavities. It is shown that the absorption can reach almost 100% around a given frequency, which is determined by the two-cavity lengths. It is also shown that hysteresis in the absorbance is possible, with the transmittance amplitude of the mirrors working as an external driving field. The role of non-linear contributions to the optical susceptibility of graphene is discussed.
The combination of plasmonic nanoparticles and graphene enhances the responsivity and spectral selectivity of graphene-based photodetectors. However, the small area of the metal-graphene junction, where the induced electron-hole pairs separate, limits the photoactive region to sub-micron length scales. Here, we couple graphene with a plasmonic grating and exploit the resulting surface plasmon polaritons to deliver the collected photons to the junction region of a metal-graphene-metal photodetector. This results into a 400% enhancement of responsivity and a 1000% increase in photoactive length,…
The electronic properties of graphene are unique and are attracting increased attention to this novel 2-dimensional system. Its photonic properties are not less impressive. For example, this single atomic layer absorbs through direct interband transitions a considerable fraction of the light (~2.3%) over a very a broad wavelength range. However, while applications in electronics are vigorously being pursued, photonic applications have not attracted as much attention. Here, we report on ultrafast photocurrent response measurements in graphene (single and few-layers) field-effect-transistors (FE…
We have fabricated UV-sensitive photodetectors based on colloidal CdS nanocrystals and graphene. The nanocrystals act as a sensitizer layer that improves light harvesting leading to high responsivity of the detector. Despite the slow relaxation of the photogenerated charges in the nanocrystal film, faster processes allowed to detect pulses up to a repetition rate of 2 kHz. We have performed time-resolved analysis of the processes occurring in our hybrid system, and discuss possible photo-induced charge transfer mechanisms.
We investigated the electronic and optoelectronic properties of vertical van der Waals heterostructure photodetectors using layered p type GaSe and n type InSe, with graphene as the transparent electrodes. Not only the photocurrent peaks from the layered GaSe and InSe themselves were observed, also the interlayer optical transition peak was observed, which is consistent with the first-principles calculation. The built-in electric field between p-n heterojunction and the advantage of the graphene electrodes can effectively separate the photo-induced electron-hole pairs, and thus lead to the res…
Graphene, owing to its zero bandgap electronic structure, is promising as an absorption material for ultra-wideband photodetection applications. However, graphene-absorption based detectors inherently suffer from poor responsivity due to weak absorption and fast photocarrier recombination, limiting their viability for low intensity light detection. Here we use a graphene/WS$_2$/MoS$_2$ vertical heterojunction to demonstrate a highly sensitive photodetector, where the graphene layer serves dual purpose, namely as the light absorption layer, and also as the carrier conduction channel, thus maint…
Graphene has emerged as a promising material for photonic applications fuelled by its superior electronic and optical properties. However, the photoresponsivity is limited by the low absorption cross section and ultrafast recombination rates of photoexcited carriers. Here we demonstrate a photoconductive gain of $\sim$ 10$^5$ electrons per photon in a carbon nanotube-graphene one dimensional-two dimensional hybrid due to efficient photocarriers generation and transport within the nanostructure. A broadband photodetector (covering 400 nm to 1550 nm) based on such hybrid films is fabricated with…
While silicon has dominated solid-state electronics for more than four decades, a variety of new materials have been introduced into photonics to expand the accessible wavelength range and to improve the performance of photonic devices. For example, gallium-nitride based materials enable the light emission at blue and ultraviolet wavelengths, and high index contrast silicon-on-insulator facilitates the realization of ultra dense and CMOS compatible photonic devices. Here, we report the first deployment of graphene, a two-dimensional carbon material, as the photo-detection element in a 10 Gbits…
We present flexible photodetectors (PDs) for visible wavelengths fabricated by stacking centimetre-scale chemical vapour deposited (CVD) single layer graphene (SLG) and single layer CVD MoS2, both wet transferred onto a flexible polyethylene terephthalate substrate. The operation mechanism relies on injection of photoexcited electrons from MoS2 to the SLG channel. The external responsivity is 45.5A/W and the internal 570A/W at 642nm. This is at least two orders of magnitude higher than bulk-semiconductor flexible membranes and other flexible PDs based on graphene and layered materials. The pho…
We report vertically-illuminated, resonant cavity enhanced, graphene-Si Schottky photodetectors (PDs) operating at 1550nm. These exploit internal photoemission at the graphene-Si interface. To obtain spectral selectivity and enhance responsivity, the PDs are integrated with an optical cavity, resulting in multiple reflections at resonance, and enhanced absorption in graphene. Our devices have wavelength-dependent photoresponse with external (internal) responsivity~20mA/W (0.25A/W). The spectral-selectivity may be further tuned by varying the cavity resonant wavelength. Our devices pave the way…
Graphene-based photodetectors are promising new devices for high-speed optoelectronic applications. However, despite recent efforts, it is not clear what determines the ultimate speed limit of these devices. Here, we present measurements of the intrinsic response time of metal-graphene-metal photodetectors with monolayer graphene using an optical correlation technique with ultrashort laser pulses. We obtain a response time of 2.1 ps that is mainly given by the short lifetime of the photogenerated carriers. This time translates into a bandwidth of ~262 GHz. Moreover, we investigate the dependen…
We report an on-chip integrated metal-graphene-silicon plasmonic Schottky photodetector with 85mA/W responsivity at 1.55 um and 7% internal quantum efficiency. This is one order of magnitude higher than metal-silicon Schottky photodetectors operated in the same conditions. At a reverse bias of 3V, we achieve avalanche multiplication, with 0.37A/W responsivity and avalanche photogain~2. This paves the way to graphene integrated silicon photonics.
Graphene's high mobility and Fermi velocity, combined with its constant light absorption in the visible to far-infrared range, make it an ideal material to fabricate high-speed and ultra-broadband photodetectors. However, the precise mechanism of photodetection is still debated. Here, we report wavelength and polarization dependent measurements of metal-graphene-metal photodetectors. This allows us to quantify and control the relative contributions of both photo-thermo- and photoelectric effects, both contributing to the overall photoresponse. This paves the way for a more efficient photodetec…
We analyze the modulation characteristics of the uncooled terahertz (THz) and infrared (IR) detectors using the variation of the density and effective temperature of the two-dimensional electron-hole plasma in uniform graphene layers (GLs) and perforated graphene layers (PGLs) due to the absorption of THz and IR radiation. The performance of the photodetectors (both the GL-photoresistor and the PGL-based barrier photodiodes) are compared. Their characteristics are also compared with the GL reverse-biased photodiodes. The obtained results allow to evaluate the ultimate modulation frequencies of…
With its electrically tunable light absorption and ultrafast photoresponse, graphene is a promising candidate for high-speed chip-integrated photonics. The generation mechanisms of photosignals in graphene photodetectors have been studied extensively in the past years. However, the knowledge about efficient light conversion at graphene pn-junctions has not yet been translated into high-performance devices. Here, we present a graphene photodetector integrated on a silicon slot-waveguide, acting as a dual-gate to create a pn-junction in the optical absorption region of the device. While at zero …
We fabricated large area infrared photodetector devices from thin film of chemically reduced graphene oxide (RGO) sheets and studied their photoresponse as a function of laser position. We found that the photocurrent either increases, decreases or remain almost zero depending upon the position of the laser spot with respect to the electrodes. The position sensitive photoresponse is explained by Schottky barrier modulation at the RGO film-electrode interface. The time response of the photocurrent is dramatically slower than single sheet of graphene possibly due to disorder from the chemically s…
Metal-graphene-metal photodetectors utilize photocurrent generated near the graphene/metal junctions and have many advantages including high speed and broad-band operation. Here, we report on photocurrent generation at ABA/ABC stacking domain junctions in tri-layer graphene with a responsivity of 0.18 A/W. Unlike usual metal-graphene-metal devices, the photocurrent is generated in the middle of the graphene channel, not confined to the vicinity of the metal electrodes. The magnitude and the direction of the photocurrent depend on the back-gate bias. Theoretical calculations show that there is …
Graphene-based photodetectors have demonstrated mechanical flexibility, large operating bandwidth, and broadband spectral response. However, their linear dynamic range (LDR) is limited by graphene's intrinsichot-carrier dynamics, which causes deviation from a linear photoresponse at low incident powers. At the same time, multiplication of hot carriers causes the photoactive region to be smeared over distances of a few micro-meters, limiting the use of graphene in high-resolution applications. We present a novel method for engineer-ing photoactive junctions in FeCl3-intercalated graphene using …
Bilayer graphene has many unique optoelectronic properties , including a tuneable band gap, that make it possible to develop new and more efficient optical and nanoelectronic devices. We have developed a Monte Carlo simulation for a single photon counting photodetector incorporating bilayer graphene. Our results show that, conceptually it would be feasible to manufacture a single photon counting photodetector (with colour sensitivity) from bilayer graphene for use across both optical and infrared wavelengths. Our concept exploits the high carrier mobility and tuneable band gap associated with …
In order to increase the response speed of the InSe-based photodetector with high photoresponsivity, graphene is used as the transparent electrodes to modify the difference of the work function between the electrodes and the InSe. As expected, the response speed of InSe/graphene photodetectors is down to 120 μs, which is about 40 times faster than that of our InSe/metal device. And it can also be tuned by the back-gate voltage from 310 μs down to 100 μs. With high response speed, the photoresponsivity can reach as high as 60 AW-1 simultaneously. Meanwhile the InSe/graphene photodetectors posse…
Graphene is an attractive material for broadband photodetection but suffers from weak light absorption. Coating graphene with quantum dots can significantly enhance light absorption and create extraordinarily high photo gain. This high gain is often explained by the classical gain theory which is unfortunately an implicit function and may even be questionable. In this work, we managed to derive explicit gain equations for hybrid graphene-quantum-dot photodetectors. Due to the work function mismatch, lead sulfide (PbS) quantum dots coated on graphene will form a surface depletion region near th…
Two-dimensional materials such as graphene and transition metal dichalcogenides (TMDs) are ideal candidates to create ultra-thin electronics suitable for flexible substrates. Although optoelectronic devices based on TMDs have demonstrated remarkable performance, scalability is still a significant issue. Most devices are created using techniques that are not suitable for mass production, such as mechanical exfoliation of monolayer flakes and patterning by electron-beam lithography. Here we show that large-area MoS2 grown by chemical vapor deposition and patterned by photolithography yields high…
We appraise a waveguide-integrated plasmonic graphene photodetector based on the hot carrier photo-bolometric effect, with performance characterized simultaneously by high responsivity, on the scale of hundreds of AW-1, and high speed on the scale of 100s of GHz. Performance evaluation is based on a theory of bolometric effect originating from the band nonparabolicity of graphene. Results compare favorably with the state-of-the-art plasmonic bolometric photodetectors, predicting up to two orders of magnitude increase in a responsivity while keeping speed on the same level, defined by the elect…
We propose and evaluate the graphene layer (GL) infrared photodetectors (GLIPs) based on the van der Waals (vdW) heterostructures with the radiation absorbing GLs. The operation of the GLIPs is associated with the electron photoexcitation from the GL valence band to the continuum states above the inter-GL barriers (either via tunneling or direct transitions to the continuum states). Using the developed device model, we calculate the photodetector characteristics as functions of the GL-vdW heterostructure parameters. We show that due to a relatively large efficiency of the electron photoexcitat…
Metamaterials have recently established a new paradigm for enhanced light absorption in state-of-the-art photodetectors. Here, we demonstrate broadband, highly efficient, polarization-insensitive, and gate-tunable photodetection at room temperature in a novel metadevice based on gold/graphene Sierpinski carpet plasmonic fractals. We observed an unprecedented internal quantum efficiency up to 100% from the near-infrared to the visible range with an upper bound of optical detectivity of $10^{11}$ Jones and a gain up to $10^{6}$, which is a fingerprint of multiple hot carriers photogenerated in g…
Dual-band infrared photodetectors (DBIPs) can discriminate desired signals from complex scenes and thus are highly expected for threat-warning, remote sensing, and astronomy applications. Conventional DBIPs with high-performances are, however, typically based on semiconductor thin films, but remain the challenges of complex spatial align, expensive growth and cooling requirement. Here, we report a tunable graphene plasmonic photodetector with dual-band infrared spectral selectivity driven by ferroelectric superdomain. The periodic ferroelectric polarization array with nanoscale ring shapes pro…
We have studied the optical properties of two-dimensional (2D) Schottky photodiode heterojunctions made of chemical vapor deposited (CVD) graphene on n- and p-type Silicon (Si) substrates. Much better rectification behavior is observed from the diodes fabricated on n- Si substrates in comparison with the devices on p-Si substrates in dark condition. Also, graphene/n-Si photodiodes show a considerable responsivity of 270 mA/W within the silicon spectral range in DC reverse bias condition. The present results are furthermore compared with that of a molybdenum disulfide (MoS2)/p-type silicon phot…
We investigate waveguide-integrated plasmonic graphene photodetector operating based on the hot carrier photo-bolometric effect, which is characterized simultaneously by high responsivity on the scale of hundreds of AW-1 and high speed on the scale of 100s of GHz. We develop a theory of bolometric effect originating from the band nonparabolicity of graphene and estimate responsivity due to bolometric effect is shown to significantly surpass the responsivity of co-existing photo-conductive effect thus convincingly demonstrating the dominance of bolometric effect. Based on the theory we propose …
Graphene-based photodetectors have shown responsivities up to 10$^8$A/W and photoconductive gains up to 10$^{8}$ electrons per photon. These photodetectors rely on a highly absorbing layer in close proximity of graphene, which induces a shift of the graphene chemical potential upon absorption, hence modifying its channel resistance. However, due to the semi-metallic nature of graphene, the readout requires dark currents of hundreds of $μ$A up to mA, leading to high power consumption needed for the device operation. Here we propose a novel approach for highly responsive graphene-based photodete…
We present a micrometer scale, on-chip integrated, plasmonic enhanced graphene photodetector (GPD) for telecom wavelengths operating at zero dark current. The GPD is designed and optimized to directly generate a photovoltage and has an external responsivity~12.2V/W with a 3dB bandwidth~42GHz. We utilize Au split-gates with a$\sim$100nm gap to electrostatically create a p-n-junction and simultaneously guide a surface plasmon polariton gap-mode. This increases light-graphene interaction and optical absorption and results in an increased electronic temperature and steeper temperature gradient acr…
The design of efficient graphene-silicon (GSi) Schottky junction photodetectors requires detailed understanding of the spatial origin of the photoresponse. Scanning-photocurrent-microscopy (SPM) studies have been carried out in the visible wavelengths regions only, in which the response due to silicon is dominant. Here we present comparative SPM studies in the visible ($λ$ = 633nm) and infrared ($λ$ = 1550nm) wavelength regions for a number of GSi Schottky junction photodetector architectures, revealing the photoresponse mechanisms for silicon and graphene dominated responses, respectively, an…
The monolithic integration of novel nanomaterials with mature and established technologies has considerably widened the scope and potential of nanophotonics. For example, the integration of single semiconductor quantum dots into photonic crystals has enabled highly efficient single-photon sources. Recently, there has also been an increasing interest in using graphene - a single atomic layer of carbon - for optoelectronic devices. However, being an inherently weak optical absorber (only 2.3 % absorption), graphene has to be incorporated into a high-performance optical resonator or waveguide to …
Graphene-silicon (GS) Schottky junctions have been demonstrated as an efficient architecture for photodetection. However, the response speed of such devices for free space light detection has so far been limited to 10's-100's of kHz for wavelength $λ>$ 500nm. Here, we demonstrate graphene-silicon Schottky junction photodetectors fabricated on a silicon-on-insulator substrate (SOI) with response speeds approaching 1GHz, attributed to the reduction of the photo-active silicon layer thickness to 10$μ$m and with it a suppression of speed-limiting diffusion currents. Graphene-silicon-on-insulator p…
We report on the integration of large area CVD grown single- and bilayer graphene transparent conductive electrodes (TCEs) on amorphous silicon multispectral photodetectors. The broadband transmission of graphene results in 440% enhancement of the detectors' spectral response in the ultraviolet (UV) region at λ = 320 nm compared to reference devices with conventional aluminum doped zinc oxide (ZnO:Al) electrodes. The maximum responsivity of the multispectral photodetectors can be tuned in their wavelength from 320 nm to 510 nm by an external bias voltage, allowing single pixel detection of UV …
We propose an on-chip CMOS compatible graphene plasmonic photodetector based on the photo-thermoelectric effect (PTE) that occurs across an entire homogeneous graphene channel. The proposed photodetector incorporates the long-range dielectric-loaded surface plasmon polariton (LR-DLSPP) waveguide with a metal stripe serving simultaneously as a plasmon supporting metallic material and one of the metal electrodes. Large in-plane component of the transverse magnetic (TM) plasmonic mode can couple efficiently to the graphene causing large temperature increases across an entire graphene channel with…
The combination of graphene with semiconductor materials in heterostructure photodetectors, has enabled amplified detection of femtowatt light signals using micron-scale electronic devices. Presently, the speed of such detectors is limited by long-lived charge traps and impractical strategies, e.g. the use of large gate voltage pulses, have been employed to achieve bandwidths suitable for applications, such as video-frame-rate imaging. Here, we report atomically thin graphene-WS$_2$ heterostructure photodetectors encapsulated in an ionic polymer, which are uniquely able to operate at bandwidth…
Optical interconnects are becoming attractive alternatives to electrical wiring in intra- and inter-chip communication links. Particularly, the integration with silicon complementary metal-oxide-semiconductor (CMOS) technology has received considerable interest due to the ability of cost-effective integration of electronics and optics on a single chip. While silicon enables the realization of optical waveguides and passive components, the integration of another, optically absorbing, material is required for photodetection. Germanium or compound semiconductors are traditionally used for this pu…
We demonstrate that surface plasmon resonances excited by photon tunneling through an adjacent dielectric medium enhance photocurrent detected by a graphene photodetector. The device is created by overlaying a graphene sheet over an etched gap in a gold film deposited on glass. The detected photocurrents are compared for five different excitation wavelengths, ranging from nm to nm. The photocurrent excited with incident p-polarized light (the case for resonant surface plasmon excitation) is significantly amplified in comparison with that for s-polarized light (without surface plasmon resonance…
Dynamic wavelength tunability has long been the holy grail of photodetector technology. Because of its atomic thickness and unique properties, graphene opens up new paradigms to realize this concept, but so far this has been elusive experimentally. Here we employ detailed quantum transport modeling of photocurrent in graphene field-effect transistors (including realistic electromagnetic fields) to show that wavelength tunability is possible by dynamically changing the gate voltage. We reveal the phenomena that govern the behavior of this type of device and show significant departure from the s…
For optical communication, information is converted between optical and electrical signal domains at a high rate. The devices to achieve such a conversion are various types of electro-optical modulators and photodetectors. These two types of optoelectronic devices, equally important, require different materials and consequently it has been challenging to realize both using a single material combination, especially in a way that can be integrated on the ubiquitous silicon platform. Graphene, with its gapless band structure, stands out as a unique optoelectronic material that allows both photode…
In recent years, the data traffic has grown exponentially and the forecasts indicate a huge market that could be addressed by communication infrastructure and service providers. However, the processing capacity, space, and energy consumption of the available technology is a serious bottleneck for the exploitation of these markets. Chip-integrated optical communication systems hold the promise of significantly improving these issues related to the current technology. At the moment, the answer to the question which material is best suited for ultrafast chip integrated communication systems is st…
We present a proof of concept for a spectrally selective near-infrared (NIR) and short-wavelength infrared (SWIR) photodetector based on nanopatterned multilayer graphene intercalated with FeCl$_3$ (NPMLG-FeCl$_3$), enabling large modulation p-doping of graphene. The localized surface plasmons (LSPs) on the graphene sheets in NPMLG-FeCl$_3$ allow for electrostatic tuning of the photodetection in the NIR and SWIR regimes from $λ=1.3$ $μ$m to 3 $μ$m, which is out of range for nanopatterned monolayer graphene (NPG). Most importantly, the LSPs along with an optical cavity increase the absorbance f…
We present a graphene photodetector for telecom applications based on a silicon photonic crystal defect waveguide. The photonic structure is used to confine the propagating light in a narrow region in the graphene layer to enhance light-matter interaction. Additionally, it is utilized as split-gate electrode to create a pn-junction in the vicinity of the optical absorption region. The photonic crystal defect waveguide allows for optimal photo-thermoelectric conversion of the occurring temperature profile in graphene into a photovoltage due to additional silicon slabs on both sides of the waveg…
Layered two-dimensional materials have shown novel optoelectronic properties and are well suited to be integrated in planar photonic circuits. For example, graphene has been utilized for wideband photodetection. Because graphene lacks a band gap, however, graphene photodetectors suffer from very high dark current. In contrast, layered black phosphorous, the latest addition to the family of 2D materials, is well-suited for photodetector applications due to its narrow but finite band gap. Here, we demonstrate a gated multilayer black phosphorus photodetector integrated on a silicon photonic wave…
A graphene bilayer phototransistor (GBL-PT) is proposed and analyzed. The GBL-PT under consideration has the structure of a field-effect transistor with a GBL as the channel and the back and top gates. The positive bias of the back gate results in the formation of conducting source and drain sections in the channel, while the negatively biased top gate provides the potential barrier which is controlled by the charge of the photogenerated holes. The features of the GBL-PT operation are associated with the variations of both the potential distribution and the energy gap in different sections of …
We propose and evaluate the vertical cascade terahertz and infrared photodetectors based on multiple-graphene-layer (GL) structures with thin tunnel barrier layers (made of tungsten disulfide or related materials). The photodetector operation is associated with the cascaded radiative electron transitions from the valence band in GLs to the conduction band in the neighboring GLs (interband- and inter-GL transitions). We calculate the spectral dependences of the responsivity and detectivity for the vertical cascade interband GL- photodetectors (I-GLPDs) with different number of GLs and doping le…
Graphene-Silicon Schottky diode photodetectors possess beneficial properties such as high responsivities and detectivities, broad spectral wavelength operation and high operating speeds. Various routes and architectures have been employed in the past to fabricate devices. Devices are commonly based on the removal of the silicon-oxide layer on the surface of silicon by wet-etching before deposition of graphene on top of silicon to form the graphene-silicon Schottky junction. In this work, we systematically investigate the influence of the interfacial oxide layer, the fabrication technique emplo…
Graphene is an ideal material for hot-electron bolometers, due to its low heat capacity and weak electron-phonon coupling. Nanostructuring graphene with quantum dot constrictions yields detectors with extraordinarily high intrinsic responsivity, higher than 1x10^9 V/W at 3K. The sensing mechanism is bolometric in nature: the quantum confinement gap causes a strong dependence of the electrical resistance on the electron temperature. Here we show that this quantum confinement gap does not impose a limitation on the photon energy for light detection and these quantum dot bolometers work in a very…
Graphene-based Photodetector with Engineered Hot Carrier Cooling Dynamics
Imec；Ghent University–imec（根特大学-imec）；Catalan Institute of Nanoscience and Nanotechnology (ICN2), CSIC and BIST（加泰罗尼亚纳米科学和纳米技术研究所（ICN2），西班牙高等科学研究委员会和巴塞尔研究所）；TU Eindhoven（埃因霍温理工大学）；Utrecht University（乌得勒支大学）；The University of Manchester（曼彻斯特大学）
Universal reconstructive polarimetry with graphene-metal infrared photodetectors
Moscow Institute of Physics and Technology（莫斯科物理技术学院）；Programmable Functional Materials Lab, Center for Neurophysics and Neuromorphic Technologies（可编程功能材料实验室，神经物理与类脑技术中心）；Department of Materials Science and Engineering, National University of Singapore（新加坡国立大学材料科学与工程系）；School of Materials Science and（材料科学与）
We demonstrate the controlled enhancement of photoresponsivity in a graphene photodetector by coupling to slow light modes in a long photonic crystal linear defect cavity. Near the Brillouin zone (BZ) boundary, spectral coupling of multiple cavity modes results in broad-band photocurrent enhancement from 1530 nm to 1540 nm. Away from the BZ boundary, individual cavity resonances enhance the photocurrent eight-fold in narrow resonant peaks. Optimization of the photocurrent via critical coupling of the incident field with the graphene-cavity system is discussed. The enhanced photocurrent demonst…
We propose to utilize multiple-graphene-layer structures with lateral p-i-n junctions for terahertz (THz) and infrared (IR) photodetection and substantiate the operation of photodetectors based on these structures. Using the developed device model, we calculate the detector dc responsivity and detectivity as functions of the number of graphene layers and geometrical parameters and show that the dc responsivity and detectivity can be fairly large, particularly, at the lower end of the THz range at room temperatures. Due to relatively high quantum efficiency and low thermogeneration rate, the ph…
The efforts to pursue photo detection with extreme performance in terms of ultrafast response time, broad detection wavelength range, and high sensitivity have never been exhausted as driven by its wide range of optoelectronic and photonic applications such as optical communications, interconnects, imaging and remote sensing1. 2D Dirac semimetal graphene has shown excellent potential toward high performance photodetector with high operation speed, broadband response and efficient carrier multiplications benefiting from its linear dispersion band structure with high carrier mobility and zero ba…
We study the operation of infrared photodetectors based on van der Waals heterostructures with the multiple graphene layers (GLs) and n-type emitter and collector contacts. The operation of such GL infrared photodetectors (GLIPs) is associated with the photoassisted escape of electrons from the GLs into the continuum states in the conduction band of the barrier layers due to the interband photon absorption, the propagation of these electrons and the electrons injected from the emitter across the heterostructure and their collection by the collector contact. The space charge of the holes trappe…
The integration of different two-dimensional materials within a multilayer van der Waals (vdW) heterostructure offers a promising technology for realizing high performance opto-electronic devices such as photodetectors and light sources1-3. Transition metal dichalcogenides, e.g. MoS2 and WSe2, have been employed as the optically-active layer in recently developed heterojunctions. However, MoS2 and WSe2 become direct band gap semiconductors only in mono- or bilayer form4,5. In contrast, the metal monochalcogenides InSe and GaSe retain a direct bandgap over a wide range of layer thicknesses from…
