S. G. Chigarev, E. M. Epshtein, Yu. V. Gulyaev, P. E. Zilberman
The results are presented of a numerical simulation of the switching magnetic junction by a spin-polarized current pulse under applied magnetic field with the current density and field below the threshold values. A possibility is shown of the switching with controllable time delay relative to the current pulse.
机构、总结、中文摘要均由AI分析而来，可能存在错误，请以论文正文为准。
继续探索
We investigate the dependence of switching current density on the junction sizes in the spin transfer torque nanopillar structures by using micromagnetic simulations. While the macro spin model predicts weak dependence of switching current density on the junction sizes, we find that the switching current density is a sensitive function of the junction sizes. It can be explained with the complicated spin configurations and dynamics during the switching process. The detail spin configurations and dynamics are determined by spin wave excitation with the finite wave vector, which is related with t…
We investigated electroforming-free bipolar resistive switching behavior in Pt/Ti/Al2O3/Al tunnel junctions where the Al2O3 tunnel barrier was naturally formed on Al in air. Various compliance current values for the junction's set switching successfully lead to various resistance values in its low resistance state, suggesting the possibility for multi-level-operation. A mechanism for the bipolar switching is qualitatively discussed in terms of the modulation of the tunnel barrier by the reactive Ti layer on top of the barrier.
The stability is analyzed of the equilibrium configurations of a magnetic junction with a free layer that has cubic symmetry and two anisotropy axes in the layer plane. Different variants of the switching between various configurations are considered. A possibility is shown of the substantial lowering of the threshold current density needed for the switching. Numerical simulation is made of the switching dynamics for various configurations.
A new mechanism different from the spin accumulation picture is proposed for the current induced magnetization switching in magnetic tunnel junctions by taking into account the effect of the electron electron interaction. We found in tunnel structures the possibility of an enhanced spin switching effect that, when normalized with respect to the current, is much bigger than that in multilayers. Some recent experimental results show evidence for the present picture.
Magnetic tunnel junctions for spin-transfer torque switching were prepared to investigate the dielectric breakdown. The breakdown occurs typically at voltages not much higher than the switching voltages, a bottleneck for the implementation of spin-transfer torque Magnetic Random Access Memory. Intact and broken tunnel junctions are characterized by transport measurements and then prepared for transmission electron microscopy and energy dispersive x-ray spectrometry by focussed ion beam. The comparison to our previous model of the electric breakdown for thicker MgO tunnel barriers reveals signi…
We propose and computationally analyze a nonvolatile static random access memory (NV-SRAM) cell using magnetic tunnel junctions (MTJs) with magnetic-field-free current-induced magnetization switching (CIMS) architecture. A pair of MTJs connected to the storage nodes of a standard SRAM cell with CIMS architecture enables fully electrical store and restore operations for nonvolatile logic information. The proposed NV-SRAM is expected to be a key component of next-generation power-gating logic systems with extremely low static-power dissipation.
Magnetic tunnel junctions (MTJ) have been grown by using molecular beam epitaxy on c-plane Al2O3 substrates. The MTJ stacks consist of two ferromagnetic hcp-Co layers separated by a thin insulating h-BN barrier. The samples have been grown in a single run revealing single crystalline epitaxial structures with sharp interfaces as observed by applying transmission electron microscopy. The in-plane magnetization experiments have revealed separate magnetization switching of a thin top Co (soft) layer and a thick bottom Co (hard) layer. At zero magnetic field the two Co layers are found in an antip…
Pressure-induced polarization switching in ferroelectric thin films has emerged as a powerful method for domain patterning, allowing to create predefined domain patterns on free surfaces and under thin conductive top electrodes. However, the mechanisms for pressure induced polarization switching in ferroelectrics remain highly controversial, with flexoelectricity, polarization rotation and suppression, and bulk and surface electrochemical processes all being potentially relevant. Here we classify possible pressure induced switching mechanisms, perform elementary estimates, and study in depth u…
In the persistent photoconductivity (PPC) phenomenon, illumination of a YBCO thin film junction with a 1mW He-Ne laser leads to the decrease of the critical critical voltage (similar to the threshold voltage). The decrease of the critical votage was reversed by illumination with incadenscent light. The critical voltage across the junction was experimentally decreased and increased by alternating illumination between He-Ne laser and incandescent light. We also observed visible quenching of the photo-induced state using a 5mW He-Ne laser. Finally, the threshold behavior of the junction was destr…
A possible mechanism for the resistive switching observed experimentally in Fe/MgO/V/Fe junctions is presented. Ab initio total energy calculations within the local density approximation and pseudopotential theory shows that by moving the oxygen ions across the MgO/V interface one obtains a metastable state. It is argued that this state can be reached by applying an electric field across the interface. In addition, the ground state and the metastable state show different electric conductances. The latter results are discussed in terms of the changes of the density of states at the Fermi level …
In magnetic nanostructures one usually uses a magnetic field to commute between two resistance (R) states. A less common but technologically more interesting alternative to achieve R-switching is to use an electrical current, preferably of low intensity. Such Current Induced Switching (CIS) was recently observed in thin magnetic tunnel junctions, and attributed to electromigration of atoms into/out of the insulator. Here we study the Current Induced Switching, electrical resistance, and magnetoresistance of thin MnIr/CoFe/AlO$_x$/CoFe tunnel junctions. The CIS effect at room temperature amount…
Transport properties have been studied for a perovskite heterojunction consisting of SrRuO$_{3}$ (SRO) film epitaxially grown on SrTi$_{0.99}$Nb$_{0.01}$O$_{3}$ (Nb:STO) substrate. The SRO/Nb:STO interface exhibits rectifying current-voltage ($I$-$V$) characteristics agreeing with those of a Schottky junction composed of a deep work-function metal (SRO) and an $n$-type semiconductor (Nb:STO). A hysteresis appears in the $I$-$V$ characteristics, where high resistance and low resistance states are induced by reverse and forward bias stresses, respectively. The resistance switching is also trigge…
Current flowing is studied in magnetic junctions consisting of a ferromagnetic metal (FM), antiferromagnetic conductor (AFM) and a nonmagnetic metal closing the electric circuit. The FM layer with high anisotropy and pinned spins of the magnetic atoms in the lattice acts as a spin injector relative to the AFM layer. To obtain resulting magnetization in the AFM layer, magnetic field is applied, which may be varied to control the magnetization. The spin-polarized current from the FM layer creates a torque and makes it possible to switch the magnetization. A possibility is shown to lower the thre…
Recent research has indicated that introducing impurities that increase the resistivity of Pt can enhance the efficiency of the spin Hall torque it generates. Here we directly demonstrate the usefulness of this strategy by fabricating prototype 3-terminal in-plane-magnetized magnetic tunnel junctions that utilize the spin Hall torque from a $\rm{Pt}_{85}\rm{Hf}_{15}$ alloy, and measuring the critical currents for switching. We find that $\rm{Pt}_{85}\rm{Hf}_{15}$ reduces the switching current densities compared to pure Pt by approximately a factor of 2 for both quasi-static ramped current bias…
Current-driven magnetization switching in low-resistance Co40Fe40B20/MgO/Co40Fe40B20 magnetic tunnel junctions (MTJs) is reported. The critical-current densities Jc required for current-driven switching in samples annealed at 270C and 300C are found to be as low as 7.8 x 10^5 A/cm^2 and 8.8 x 10^5 A/cm^2 with accompanying tunnel magnetoresistance (TMR) ratios of 49% and 73 %, respectively. Further annealing of the samples at 350C increases TMR ratio to 160 %, while accompanying Jc increases to 2.5 x 10^6 A/cm^2. We attribute the low Jc to the high spin-polarization of tunnel current and small …
This letter reports on the observation of optoelectronic switching in addressable molecular crossbar junctions fabricated using polymer stamp-printing method. The active medium in the junction is a molecular self-assembled monolayer softly sandwiched between gold electrodes. The molecular junctions are investigated through currentvoltage measurements at varied temperature (from 95 to 300 K) in high vacuum condition. The junctions show reversible optoelectronic switching with the highest on/off ratio of 3 orders of magnitude at 95 K. The switching behavior is independent of both optical wavelen…
Current-induced switching is considered in a magnetic junction. The junction includes pinned and free ferromagnetic layers which work in the regime of the high spin injection. It is shown that in such a regime the exchange magnetization reversal threshold can be lowered up to two times when the axes of the layers are noncollinear.
Low voltage local strain enhanced switching of magnetic tunnel junctions
针对 CoFeB-MgO 基磁隧道结应变调控电压过高的问题，本文利用局部栅极电场诱导应变，在 200 mV 低电压下实现开关场控制和隧道磁阻线性增强。
We report the intrinsic critical current density (Jc0) in current-induced magnetization switching and the thermal stability factor (E/kBT, where E, kB, and T are the energy potential, the Boltzmann constant, and temperature, respectively) in MgO based magnetic tunnel junctions with a Co40Fe40B20(2nm)/Ru(0.7-2.4nm)/Co40Fe40B20(2nm) synthetic ferrimagnetic (SyF) free layer. We show that Jc0 and E/kBT can be determined by analyzing the average critical current density as a function of coercivity using the Slonczewski's model taking into account thermal fluctuation. We find that high antiferromagn…
We report pulsed as well as direct current/voltage induced electroresistance in Bi0.8Sr0.2MnO3 at room temperature. It is shown that bi-level and multi-level resistivity switching can be induced by a sequence of pulses of varying pulse width at fixed voltage amplitude. Resistivity increases abruptly (= 55 % at 300 K) upon reducing pulse width from 100 ms to 25 ms for a fixed electric field (E = 2 V/cm2) of 200 ms pulse period. The resistivity switching is accompanied by a periodic change in temperature which alone can not explain the magnitude of the resistivity change.
Many questions are still open regarding the physical mechanisms behind the magnetic switching in GdFeCo alloys by single optical pulses. Phenomenological models suggest a femtosecond scale exchange relaxation between sublattice magnetization as the driving mechanism for switching. The recent observation of thermally induced switching in GdFeCo by using both several picosecond optical laser pulse as well as electric current pulses has questioned this previous understanding. This has raised the question of whether or not the same switching mechanics are acting at the femo- and picosecond scales.…
The recently discovered electrical-induced switching of antiferromagnetic (AF) materials that have spatial inversion asymmetry has enriched the field of spintronics immensely and opened the door for the concept of antiferromagnetic MRAM. CuMnAs is one promising AF material that exhibits such electrical switching ability, and has been studied to switch using electrical pulses of length millisecond down to picosecond, but with little focus on nanosecond regime. We demonstrate here switching of CuMnAs/GaP using nanosecond pulses. Our results showed that in the nanosecond regime low-energy switchi…
Ferrimagnetic Heusler tunnel junctions with fast spin-transfer torque switching enabled by low magnetization
本研究利用低磁化铁磁Heusler合金Mn3Ge实现快速可靠的自旋转移力矩切换，并创下铁磁材料室温隧道磁电阻纪录，为高性能磁性随机存取存储器的扩展提供路径。
Here we demonstrate that both, tunnel magneto resistance (TMR) and resistive switching (RS), can be observed simultaneously in nano-scale magnetic tunnel junctions. The devices show bipolar RS of 6 % and TMR ratios of about 100 %. For each magnetic state, multiple resistive sates are created depending on the bias history which provides a method for multi-bit data storage and logic. The electronic transport measurements are discussed in the framework of a memristive system. Differently prepared MgO barriers are compared to gain insight into the switching mechanism.
We study the combined effects of spin transfer torque, voltage modulation of interlayer exchange coupling and magnetic anisotropy on the switching behavior of perpendicular magnetic tunnel junctions (p-MTJs). In asymmetric p-MTJs, a linear-in-voltage dependence of interlayer exchange coupling enables the effective perpendicular anisotropy barrier to be lowered for both voltage polarities. This mechanism is shown to reduce the critical switching current and effective activation energy. Finally, we analyze the possibility of having switching via interlayer exchange coupling only.
Single femtosecond pulse toggle switching of ferrimagnetic alloys is an essential building block for ultrafast spintronics. Very different element-specific demagnetization dynamics is believed to be a hard limit for switching in ferrimagnets. This suggests that ferrimagnets composed of two ions of different nature, such as rare earth transition metal alloys, are necessary for switching. However, experimental observation of toggle switching in Mn$_2$Ru$_x$Ga Heusler alloys, has contested this limit since Mn ions are of the same nature. To shed some light into this question, we present an atomis…
Single-pulse switching has been experimentally demonstrated in ferrimagnetic GdFeCo and Mn$_2$Ru$_x$Ga alloys. Complete understanding of single-pulse switching is missing due to the lack of an established theory accurately describing the transition to the non-equilibrium reversal path induced by femtosecond laser photo-excitation. In this work we present general macroscopic theory for the magnetization dynamics of ferrimagnetic materials upon femtosecond laser excitation. Our theory reproduces quantitatively all stages of the switching process observed in experiments. We directly compare our t…
We have investigated direct and pulsed current induced electroresistance in two manganites with different electronic and magnetic ground states: charge-orbital ordered 50 % Ca doped NdMnO3 and 50 % Mn doped LaNiO3. It has been shown that negative differential resistance observed at high current density in these compounds is related to Joule heating. However, bi-level and multi-level resistivity switching induced by variations in pulse width and pulse period at low current density can not be attributable to Joule heating alone. We discuss possible origins.
We show that magnetization reversal in spin-injection devices can be significantly faster when using a chirped r.f. rather than d.c current pulse. Alternatively one can use a simple sinusoidal r.f. pulse or an optimized series of alternating, equal-amplitude, square pulses of varying width (a digitized approximation to a chirped r.f. pulse) to produce switching using much smaller currents than with a d.c. pulse.
A prototype of magnetoresistive random access memory (MRAM) based on magnetic tunnel junctions (MTJ) was fabricated with crossed-anisotropy of magnetic layers on either side of the tunnelling barrier layer. It is demonstrated that the introduction of crossed-anisotropy results in smaller switching fields and better switching times compared to the conventional case of aligned anisotropies. The magnetoresistive properties of fabricated devices are in good agreement with the micromagnetic model.
A practical problem for memory applications involving perpendicularly magnetized magnetic tunnel junctions is the reliability of switching characteristics at high-bias voltage. Often it has been observed that at high-bias, additional error processes are present that cause a decrease in switching probability upon further increase of bias voltage. We identify the main cause of such error-rise process through examination of switching statistics as a function of bias voltage and applied field, and the junction switching dynamics in real time. These experiments show a coincidental onset of error-ri…
Coherent control of photomagnetic back-switching by double-pump laser pulses
本文在纯立方磁晶对称铁石榴石薄膜中，利用双泵浦激光脉冲实现了不依赖初始状态的光磁反向切换，可等效为XOR逻辑运算，频率高达50 GHz。
Despite significant progress in synthesizing several new molecules and many promising single device demonstrations, wide range acceptance of molecular electronics as an alternative to CMOS technology has been stalled not only by controversial theories of a molecular device`s operation, for example the switching mechanism, but also by our inability to reproducibly fabricate large arrays of devices. In this paper, we investigate the role of Casimir force as one of the potential source of a wide range of discrepancies in the reported electrical characteristics and high rate of device shorting in …
Current-voltage characteristics of H2-Au molecular junctions exhibit intriguing steps around a characteristic voltage of 40 mV. Surprisingly, we find that a hysteresis is connected to these steps with a typical time scale > 10 ms. This time constant scales linearly with the power dissipated in the junction beyond an ofset power P_s = IV_s. We propose that the hysteresis is related to vibrational heating of both the molecule in the junction and a set of surrounding hydrogen molecules. Remarkably, we can engineer our junctions such that the hysteresis' characteristic time becomes >days. We demon…
Single-shot all-optical magnetization switching in in-plane magnetized magnetic tunnel junction
在面内磁化磁性隧道结中，通过将Co40Fe40B20软层与Co85Gd15层交换耦合实现了单脉冲全光无螺旋度翻转，缓解了垂直磁各向异性限制并使TMR比超过100%。
Current-induced spin-transfer torques (STT) and spin-orbit torques (SOT) enable the electrical switching of magnetic tunnel junctions (MTJs) in nonvolatile magnetic random access memories. In order to develop faster memory devices, an improvement of the timescales underlying the current driven magnetization dynamics is required. Here we report all-electrical time-resolved measurements of magnetization reversal driven by SOT in a three-terminal MTJ device. Single-shot measurements of the MTJ resistance during current injection reveal that SOT switching involves a stochastic two-step process con…
Perpendicular magnetic tunnel junctions are one of the building blocks for spintronic memories, which allow fast nonvolatile data access, offering substantial potentials to revolutionize the mainstream computing architecture. However, conventional switching mechanisms of such devices are fundamentally hindered by spin polarized currents4, either spin transfer torque or spin orbit torque with spin precession time limitation and excessive power dissipation. These physical constraints significantly stimulate the advancement of modern spintronics. Here, we report an optomagnetic tunnel junction us…
Writing magnetic bits by spin-orbit torques (SOTs) arising from spin Hall effect creates new possibilities for ultrafast and low-power magnetoresistive random access memory (MRAM). For perpendicular MRAM, an extra in-plane field is required to break the symmetry for the deterministic SOT writing of the perpendicular storage layer. Although schemes have been demonstrated in external-field-free SOT switching of a perpendicular layer, practically integrating them with perpendicular MTJs still appears to be challenging. Here, we present experimental demonstration of spin-orbit torques (SOTs) switc…
We analyse the phenomenon of back-hopping in spin-torque induced switching of the magnetization in perpendicularly magnetized tunnel junctions. The analysis is based on single-shot time-resolved conductance measurements of the pulse-induced back-hopping. Studying several material variants reveals that the back-hopping is a feature of the nominally fixed system of the tunnel junction. The back-hopping is found to proceed by two sequential switching events that lead to a final state P' of conductance close to --but distinct from-- that of the conventional parallel state. The P' state does not ex…
Current-induced spin-orbit torques provide a versatile tool for switching magnetic devices. In perpendicular magnets, the dampinglike component of the torque is the main driver of magnetization reversal. The degree to which the fieldlike torque assists the switching is a matter of debate. Here we study the switching of magnetic tunnel junctions with a CoFeB free layer and either W or Ta underlayers, which have a ratio of fieldlike to dampinglike torque of 0.3 and 1, respectively. We show that the fieldlike torque can either assist or hinder the switching of CoFeB when the static in-plane magne…
We report on the current-induced magnetization switching of a three-terminal perpendicular magnetic tunnel junction by spin-orbit torque and the read-out using the tunnelling magnetoresistance (TMR) effect. The device is composed of a perpendicular Ta/FeCoB/MgO/FeCoB stack on top of a Ta current line. The magnetization of the bottom FeCoB layer can be switched reproducibly by the injection of current pulses with density $5\times10^{11}$ A/m$^2$ in the Ta layer in the presence of an in-plane bias magnetic field, leading to the full-scale change of the TMR signal. Our work demonstrates the proof…
We report measurements of magnetic switching and steady-state magnetic precession driven by spin-polarized currents in nanoscale magnetic tunnel junctions with low-resistance, < 5 Ohm-micron-squared, barriers. The current densities required for magnetic switching are similar to values for all-metallic spin-valve devices. In the tunnel junctions, spin-transfer-driven switching can occur at voltages that are high enough to quench the tunnel magnetoresistance, demonstrating that the current remains spin-polarized at these voltages.
We report on the magnetic switching and backhopping effects due to spin-transfer-torque in magnetic tunnel junctions. Experimental data on the current-induced switching in junctions with MgO tunnel barrier reveal a random back-and-forth switching between the magnetization states, which appears when the current direction favors the parallel magnetic configuration. The effect depends on the barrier thickness $t_b$, and is not observed in tunnel junctions with very thin MgO tunnel barriers, $t_b$ $<$ 0.95 nm. Switching dependence on the bias voltage and barrier thickness is explained in terms of …
Thin electrodes of magnetic tunnel junctions can show superparamagnetism at surprisingly low temperature. We analysed their thermally induced switching for varying temperature, magnetic and electric field. Although the dwell times follow an Arrhenius law, they are orders of magnitude too small compared to a model of single domain activation. Including entropic effects removes this inconsistency and leads to a magnetic activation volume much smaller than that of the electrode. Comparing data for varying barrier thickness then allows to separate the impact of Zeman energy, spin-transfer-torque a…
We time-resolve the spin-transfer-torque-induced switching in perpendicularly magnetized tunnel junctions of diameters from 50 to 250 nm in the thermally activated regime. When the field and the spin-torque concur to favor the P to AP transition, the reversal yields monotonic resistance ramps that can be interpreted as a domain wall propagation through the device at velocities of 17 to 30 nm/ns; smaller cells switch hence faster. When the field hinders the P to AP transition, the switching is preceded by repetitive switching attempts, during which the resistance transiently increases until suc…
In the quest for reliable and power-efficient memristive devices, ferroelectric tunnel junctions are being investigated as potential candidates. CMOS-compatible ferroelectric hafnium oxides are at the forefront. However, in epitaxial tunnel devices with thicknesses around ${\approx}$ 4 - 6 nm, the relatively high tunnel energy barrier produces a large resistance that challenges their implementation. Here, we show that ferroelectric and electroresistive switching can be observed in ultrathin 2 nm epitaxial Hf$_{0.5}$Zr$_{0.5}$O$_2$ (HZO) tunnel junctions in large area capacitors (${\approx} 300…
We use three-terminal magnetic tunnel junctions (MTJs) designed for field-free switching by spin-orbit torques (SOTs) to systematically study the impact of dual voltage pulses on the switching performances. We show that the concurrent action of an SOT pulse and an MTJ bias pulse allows for reducing the critical switching energy below the level typical of spin transfer torque while preserving the ability to switch the MTJ on the sub-ns time scale. By performing dc and real-time electrical measurements, we discriminate and quantify three effects arising from the MTJ bias: the voltage-controlled …
Control of magnetism without using magnetic fields enables large-scale integration of spintronic devices for memory, computation and communication in the beyond-CMOS era. Mechanisms including spin torque transfer, spin Hall effect, and electric field or strain assisted switching have been implemented to switch magnetization in various spintronic devices. Their operation speed, however, is fundamentally limited by the spin precession time to be longer than 10-100 picoseconds. Overcoming such a speed constraint is critical for the prospective development of spintronics. Here we report the demons…
We investigate fast-pulse switching of in-plane-magnetized magnetic tunnel junctions (MTJs) within 3-terminal devices in which spin-transfer torque is applied to the MTJ by the giant spin Hall effect. We measure reliable switching, with write error rates down to $10^{-5}$, using current pulses as short as just 2 ns in duration. This represents the fastest reliable switching reported to date for any spin-torque-driven magnetic memory geometry, and corresponds to a characteristic time scale that is significantly shorter than predicted possible within a macrospin model for in-plane MTJs subject t…
Optical Switching in Tb/Co-Multilayer Based Nanoscale Magnetic Tunnel Junctions
本文展示了基于Tb/Co多层膜的纳米尺度磁隧道结的光学开关，通过90飞秒激光脉冲实现单次磁化翻转，并结合电学读出验证了尺寸依赖的开关特性，为超快自旋电子器件提供实验支持。
Reconfigurable classifier based on spin torque driven magnetization switching in electrically connected magnetic tunnel junctions
本研究提出基于电连接磁隧道结网络的可重构分类器，通过自旋转矩驱动磁化翻转分类输入电流幅值编码信息，实验证明三结网络的口语元音分类识别率优于同参数量软件神经网络，为大规模神经形态网络发展提供支撑。
The electronic transport properties and switching mechanism of single photochromic diarylethene derivatives sandwiched between two gold surfaces with closed and open configurations are investigated by a fully self-consistent nonequilibrium Green's function method combined with density functional theory. The calculated transmission spectra of two configurations are strikingly distinctive. The open form lacks any significant transmission peak within a wide energy window, while the closed structure has two significant transmission peaks on the both sides of the Fermi level. The electronic transpo…
Perpendicular magnetic tunnel junctions (p-MTJs) switched utilizing bipolar electric fields have extensive applications in energy-efficient memory and logic devices. Voltage-controlled magnetic anisotropy linearly lowers the energy barrier of ferromagnetic layer via electric field effect and efficiently switches p-MTJs only with a unipolar behavior. Here we demonstrate a bipolar electric field effect switching of 100-nm p-MTJs with a synthetic antiferromagnetic free layer through voltage-controlled exchange coupling (VCEC). The switching current density, ~1.1x10^5 A/cm^2, is one order of magni…
We report on the switching of the magnetic vortex core in a Pac-man disk using a magnetic field pulse, investigated via micromagnetic simulations. The minimum core switching field is reduced by 72 % compared to that of a circular disk with the same diameter and thickness. However, the core switches irregularly with respect to both the field pulse amplitude and duration. This irregularity is induced by magnetization oscillations which arise due to excitation of the spin waves when the core annihilates. We show that the core switching can be controlled with the assist magnetic field and by chang…
All-optical helicity dependent switching (AO-HDS), deterministic control of magnetization by circularly polarized laser pulses, allows to efficiently manipulate spins without the need of a magnetic field. However, AO-HDS in ferromagnetic metals so far requires many laser pulses for fully switching their magnetic states. Using a combination of a short, 90-fs linearly polarized pulse and a subsequent longer, 3-ps circularly polarized pulse, we demonstrate that the number of pulses for full magnetization reversal can be reduced to 4 pulse pairs in a single stack of Pt/Co/Pt. The obtained results …
A low power magnetization switching scheme based on the voltage control of magnetic anisotropy (VCMA) is proposed. In contrast to the conventional switching scheme using VCMA, where the magnetic anisotropy is eliminated during the voltage pulse, the magnetic anisotropy is enhanced to induce precession around the axis close to the easy axis. After turning off the voltage proximately at a half of precession period, the magnetization relaxes to the opposite equilibrium direction. We perform numerical simulations and show that the pulse duration of the proposed switching scheme is as short as a fe…
Studying all-optical magnetization switching of GdFe by double-pulse laser excitation
本研究通过双脉冲激光激发GdFe亚铁磁合金，结合磁畴成像技术探究脉冲注量与时间延迟对全光磁化翻转的影响，揭示了再翻转的时间窗口与脉冲叠加效应，并通过原子自旋动力学模拟验证了结果，为超快全光磁存储的速度极限研究提供了依据。
Well-known conductive molecular wires, like cumulene or polyyne, provide a model for interconnecting molecular electronics circuit. In the recent experiment, the appearance of carbon wire bridging two-dimensional electrodes - graphene sheets - was observed [PRL 102, 205501 (2009)], thus demonstrating a mechanical way of producing the cumulene. In this work, we study the structure and conductance properties of the carbon wire suspended between carbon nanotubes (CNTs) of different chiralities (zigzag and armchair), and corresponding conductance variation upon stretching. We find the geometrical …
Detailed understanding of spin dynamics in magnetic nanomaterials is necessary for developing ultrafast, low-energy and high-density spintronic logic and memory. Here, we develop micromagnetic models and analytical solutions to elucidate the effect of increasing damping and uniaxial anisotropy on magnetic field pulse-assisted switching time, energy and field requirements of nanowires with perpendicular magnetic anisotropy and yttrium iron garnet-like spin transport properties. A nanowire is initially magnetized using an external magnetic field pulse (write) and self-relaxation. Next, magnetic …
It is shown theoretically that a single a few picoseconds long acoustic pulse can reverse magnetization in a magneto-strictive material Terfenol-D. Following giant magneto-elastic changes of free energy density the magnetization vector is kicked out of a local in-plane energy mininum and decays into another minimum. For acoustic pulse duration significantly shorter than magnetization precession period $τ_{ac}$<<$T_{prec}$, the switching threshold is determined by the {\it acoustic pulse area}, i.e. pulse integral in time domain, similar to coherent phenomena in optics. Simulation results are s…
扫码添加微信好友，提出您的宝贵建议 👇
💡 备注请填写：网站反馈
发表机构由 AI 从论文文本抽取，如发现错误，欢迎反馈修正建议。