A theoretical description of scanning tunneling potentoimetry (STP) measurement is presented to address the increasing need for a basis to interpret experiments on macrscopic samples. Based on a heuristic understanding of STP provided to facilitate theoretical understanding, the total tunneling current related to the density matrix of the sample is derived within the general framework of quantum transport. The measured potentiometric voltage is determined implicitly as the voltage necessary to null the tunneling current. Explicit expressions of measured voltages are presented under certain assumptions, and limiting cases are discussed to connect to previous results. The need to go forward and formulate the theory in terms of a local density matrix is also discussed.
A scanning tunneling microscopy based potentiometry technique for the measurements of the local surface electric potential is presented and illustrated by experiments performed on current-carrying thin tungsten films. The obtained results demonstrate a sub-millivolt resolution in the measured surface potential. The application of this potentiometry technique to the local sensing of the spin Hall effect is outlined and some experimental results are reported.
We present a multi-tip scanning tunneling potentiometry technique that can be implemented into existing multi-tip scanning tunneling microscopes without hardware changes. The resulting setup allows flexible in situ contacting of samples under UHV conditions and subsequent measurement of the sample topography and local electric potential with resolution down to Å and μV, respectively. The performance of the potentiometry feedback is demonstrated by thermovoltage measurements on the Ag/Si$(111)-(\sqrt3\times\sqrt3)\rm R30^{\circ}$ surface by resolving a standing wave pattern. Subsequently, the a…
Using the non-equilibrium Keldysh formalism, we investigate the spatial relation between the electro-chemical potential measured in scanning tunneling spectroscopy, and local current patterns over the entire range from the quantum to the classical transport regime. These quantities show similar spatial patterns near the quantum limit, but are related by Ohm's law only in the classical regime. We demonstrate that defects induce a Landauer residual resistivity dipole in the electro-chemical potential with the concomitant spatial current pattern representing the field lines of the dipole.
Under mesoscopic conditions, the transport potential on a thin film with current is theoretically expected to bear spatial variation due to quantum interference. Scanning tunneling potentiometry is the ideal tool to investigate such variation, by virtue of its high spatial resolution. We report in this {\it Letter} the first detailed measurement of transport potential under mesoscopic conditions. Epitaxial graphene at a temperature of 17K was chosen as the initial system for study because the characteristic transport length scales in this material are relatively large. Tip jumping artifacts ar…
This lecture has been given at the 45th Spring School: Computing Solids: Models, Ab-initio Methods and Supercomputing organized at the Forschungszentrum Jülich. The goal of this manuscript is to review the basics behind the theory accompanying Scanning Tunneling Microscopy.
This review covers recent experimental progress in probing the electronic properties of graphene and how they are influenced by various substrates, by the presence of a magnetic field and by the proximity to a superconductor. The focus is on results obtained using scanning tunneling microscopy, spectroscopy, transport and magneto-transport techniques.
We have performed low-temperature scanning tunneling spectroscopy measurements on suspended single-wall carbon nanotubes with a gate electrode allowing three-terminal spectroscopy measurements. These measurements show well-defined Coulomb diamonds as well as side peaks from phonon-assisted tunneling. The side peaks have the same gate voltage dependence as the main Coulomb peaks, directly proving that they are excitations of these states.
Acquisition and analysis is described for scanning tunneling spectroscopy data acquired from a monolayer of WSe$_2$ grown on epitaxial graphene on SiC. Curve fitting of the data is performed, in order to deduce band-edge energies. In addition to describing the details of the theoretical curves used for the fitting, the acquisition and analysis methods are also discussed within the larger context of the historical development of scanning tunneling spectroscopy techniques.
Systematic displacement measurements of freestanding graphene as a function of applied bias voltage and tunneling current setpoint using scanning tunneling microscopy (STM) are presented. When the bias voltage is increased the graphene approaches the STM tip, while, on the other hand, when the tunneling current is increased the graphene contracts from the STM tip. To understand the role of the bias voltage, we quantitatively model the attractive force between the tip and the sample using electrostatics. For the tunneling current, we qualitatively model the contraction of the graphene using ent…
Correlated electron states in high mobility two-dimensional electron systems (2DESs), including charge density waves and microemulsion phases intermediate between a Fermi liquid and Wigner crystal, are predicted to exhibit complex local charge order. Existing experimental studies, however, have mainly probed these systems at micron to millimeter scales rather than directly mapping spatial organization. Scanning probes should be well-suited to study the spatial structure of these states, but high mobility 2DESs are found at buried semiconductor interfaces, beyond the reach of conventional scann…
We report low temperature high magnetic field scanning tunneling microscopy and spectroscopy of graphene flakes on graphite that exhibit the structural and electronic properties of graphene decoupled from the substrate. Pronounced peaks in the tunneling spectra develop with field revealing a Landau level sequence that provides a direct way to identify graphene and to determine the degree of its coupling to the substrate. The Fermi velocity and quasiparticle lifetime, obtained from the positions and width of the peaks, provide access to the electron-phonon and electron-electron interactions.
In scanning tunneling experiments on semiconductor surfaces, the energy scale within the tunneling junction is usually unknown due to tip-induced band bending. Here, we experimentally recover the zero point of the energy scale by combining scanning tunneling microscopy with Kelvin probe force spectroscopy. With this technique, we revisit shallow acceptors buried in GaAs. Enhanced acceptor-related conductance is observed in negative, zero, and positive band-bending regimes. An Anderson-Hubbard model is used to rationalize our findings, capturing the crossover between the acceptor state being pa…
We have developed a fabrication process for incorporating a gate electrode into suspended single-walled carbon nanotube structures for scanning tunneling spectroscopy studies. The nanotubes are synthesized by chemical vapor deposition directly on a metal surface. The high temperature ~800 C involved in the growth process poses challenging issues such as surface roughness and integrity of the structure which are addressed in this work. We demonstrate the effectiveness of the gate on the freestanding part of the nanotubes by performing tunneling spectroscopy that reveals Coulomb blockade diamond…
Achieving a high intensity in inelastic scanning tunneling spectroscopy (IETS) is important for precise measurements. The intensity of the IETS signal can vary up to a factor three for various tips without an apparent reason accessible by scanning tunneling microscopy (STM) alone. Here, we show that combining STM and IETS with atomic force microscopy enables carbon monoxide front atom identification, revealing that high IETS intensities for CO/Cu(111) are obtained for single atom tips, while the intensity drops sharply for multi-atom tips. Adsorbing the CO molecule on a Cu adatom [CO/Cu/Cu(111…
Scanning tunneling images of carbon nanotubes frequently show electron distributions which break the local sixfold symmetry of the graphene sheet. We present a theory of these images which relates these anisotropies to the off diagonal correlations in the single particle density matrix, and allows one to extract these correlations from the observed images. The theory is applied to images of the low energy states reflected at the end of a tube or by point defects, and to states propagating on defect free semiconducting tubes. The latter exhibit a novel switching of the anisotropy in the tunneli…
Graphene flakes are prepared on freshly cleaved mica by exfoliation and studied by scanning tunneling microscopy in ultra high vacuum. On few-layer graphene, a triangular network of partial dislocations separating ABC stacked and ABA stacked graphene was found similar to the networks occasionally visible on freshly cleaved HOPG. We found differences in the electronic structure of ABC and ABA stacked areas by scanning tunneling spectroscopy, i.e., a pronounced peak at 0.25 eV above the Fermi level exclusively in the ABA areas, which is shown to be responsible for the different apparent heights …
We study electronic and topographic properties of the Si(335) surface, containing Au wires parallel to the steps. We use scanning tunneling microscopy (STM) supplemented by reflection of high energy electron diffraction (RHEED) technique. The STM data show the space and voltage dependent oscillations of the distance between STM tip and the surface which can be explained within one band tight binding Hubbard model. We calculate the STM current using nonequilibrium Keldysh Green function formalism.
We propose a new method for atomic-scale imaging of spatial current patterns in nanoscopic quantum networks by using scanning tunneling microscopy (STM). By measuring the current flowing from the STM tip into one of the leads attached to the network as a function of tip position, one obtains an atomically resolved spatial image of "current riverbeds" whose spatial structure reflects the coherent flow of electrons out of equilibrium. We show that this method can be successfully applied in variety of network topologies, and is robust against dephasing effects.
We study interfacial water trapped between a sheet of graphene and a muscovite (mica) surface using Raman spectroscopy and ultra-high vacuum scanning tunneling microscopy (UHV-STM) at room temperature. We are able to image the graphene-water interface with atomic resolution, revealing a layered network of water trapped underneath the graphene. We identify water layer numbers with a carbon nanotube height reference. Under normal scanning conditions, the water structures remain stable. However, at greater electron energies, we are able to locally manipulate the water using the STM tip.
We propose a novel probe technique capable of performing local low-temperature spectroscopy on a 2D electron system (2DES) in a semiconductor heterostructure. Motivated by predicted spatially-structured electron phases, the probe uses a charged metal tip to induce electrons to tunnel locally, directly below the tip, from a "probe" 2DES to a "subject" 2DES of interest. We test this concept with large-area (non-scanning) tunneling measurements, and predict a high spatial resolution and spectroscopic capability, with minimal influence on the physics in the subject 2DES.
The electroluminescence of a polythiophene wire suspended between two metallic electrodes is probed using a scanning tunneling microscope. Under positive sample voltage, the spectral and voltage dependencies of the emitted light are consistent with the fluorescence of the wire junction mediated by localized plasmons. This emission is strongly attenuated for the opposite polarity. Both emission mechanism and polarity dependence are similar to what occurs in organic light emitting diodes (OLED) but at the level of a single molecular wire.
We present a method capable of calculating elastic scanning tunneling microscopy (STM) currents from localized atomic orbital density functional theory (DFT). To overcome the poor accuracy of the localized orbital description of the wave functions far away from the atoms, we propagate the wave functions, using the total DFT potential. From the propagated wave functions, the Bardeen's perturbative approach provides the tunneling current. To illustrate the method we investigate carbon monoxide adsorbed on a Cu(111) surface and recover the depression/protrusion observed experimentally with normal…
Temperature imaging of nanoscale systems is a fundamental problem which has myriad potential technological applications. For example, nanoscopic cold spots can be used for spot cooling electronic components while hot spots could be used for precise activation of chemical or biological reactions. More fundamentally, imaging the temperature fields in quantum coherent conductors can provide a wealth of information on heat flow and dissipation at the smallest scales. However, despite significant technological advances, the spatial resolution of temperature imaging remains in the few nanometers ran…
A technique to locally generate mechanical vibrations in freestanding graphene using scanning tunneling microscopy (STM) is presented. The frequency of the mechanical vibrations is tuned over nearly four decades and is centered around 10 Hz. The amplitude of the vibrations also changes over nearly three decades centered on 1 nm. The oscillating motion is generated in two ways: first, by scanning the STM tip on the surface and second, by scanning the bias voltage on the STM tip. The frequency and amplitude of the displaced freestanding graphene is quantitatively transformed to the frequency and…
An extension of the direct-current, double-lamella drop-off technique for electrochemically etching tungsten scanning-tunneling-microscope tips is presented. The key fabrication step introduced here is the use of an etch stop as a simple but accurate way to optimize the contact area between the etchant and the wire. By restricting the etching process, the final cone angle of the tips can be made sharp and mechanically stable without a lot of finesse from the STM tip maker.
Atomic-scale topography of epitaxial multilayer graphene grown on 4H-SiC(0001) was investigated using scanning tunneling microscopy (STM). Bunched nano-ridges ten times smaller than previously recorded were observed throughout the surface, the morphology of which was systematically altered using a relatively new technique called electrostatic-manipulation scanning tunneling microscopy. Transformed graphene formations sometimes spontaneously returned to their original morphology, while others permanently changed. Using an electrostatic model, we calculate that a force up to ~5 nN was exerted by…
The miniaturization of semiconductor devices to the scales where small numbers of dopants can control device properties requires the development of new techniques capable of characterizing their dynamics. Investigating single dopants requires sub-nanometer spatial resolution which motivates the use of scanning tunneling microscopy (STM), however, conventional STM is limited to millisecond temporal resolution. Several methods have been developed to overcome this shortcoming. Among them is all-electronic time-resolved STM, which is used in this work to study dopant dynamics in silicon with nanos…
Indium arsenide nanowires grown by selective-area vapor phase epitaxy are used as tips for scanning tunneling microscopy (STM). The STM tips are realized by positioning the wires manually on the corner of a double cleaved gallium arsenide wafer with submicrometer precision and contacting them lithographically, which is fully compatible with further integrated circuitry on the GaAs wafer. STM images show a z-noise of 2 pm and a lateral stability of, at least, 0.5 nm on a Au(111) surface. I(z) spectroscopy reveals an exponential decay indicating tunneling through vacuum. Subsequent electron micr…
Scanning tunneling spectroscopy measures how a single electron with definite energy propagates between a sample surface and the tip of a scanning tunneling microscope. In the simplest description, the differential conductance measured is interpreted as the local density of states of the sample at the tip position. This picture, however, is insufficient in some cases, since especially smaller molecules weakly coupled with the substrate tend to have strong Coulomb interactions when an electron is inserted or removed at the molecule. We present theoretical approaches to go from the non-interactin…
Spin-momentum locking in the surface mode of topological insulators (TI) leads to the surface accumulation of spin-polarized electrons caused by bias current flows through TI samples. Here, we demonstrate that scanning tunneling microscopy can be used to sense this surface spin-polarized electron accumulation. We present experimental results of this sensing for Sn-doped Bi$_2$Se$_3$ samples by employing Fe-coated W tips as well as non-magnetic W tips. We observe a linear increase in the spin-accumulation as a function of bias current through TI samples.
Mixing of atoms at the interface was studied for Mn/Fe magnetic hetero-epitaxial layers on Cu(001) by scanning tunneling microscopy/spectroscopy. The formation of a surface alloy was observed when the Mn layer was thinner than 3 atomic layers. From the fourth layer, Fe segregation is suppressed, and a pure Mn surface appears. Accordingly, spectroscopic measurements revealed the electronic difference between the surface alloy and Mn layers. The surface electronic structure of the fourth Mn layer is slightly different from that of the fifth layers, which is attributed to the hybridization of the…
Graphene is a truly two-dimensional material with exceptional electronic, mechanical, and optical properties. As such, it consists of surface only and can be probed by the well developed surface-science techniques as, e.g., scanning tunneling microscopy. This method bridges the gap between the surface science community and the electronic device community and might lead to novel combined approaches. Here, I review some of the scanning tunneling microscopy (STM) and spectroscopy (STS) experiments on monolayer graphene samples. I will concentrate on graphene samples deposited on insulating substr…
The junction of a scanning tunneling microscope (STM) operating in the tunneling regime was irradiated with femtosecond laser pulses. A photo-excited hot electron in the STM tip resonantly tunnels into an excited state of a single molecule on the surface, converting it from the neutral to the anion. The electron transfer rate depends quadratically on the incident laser power, suggesting a two-photon excitation process. This nonlinear optical process is further confirmed by the polarization measurement. Spatial dependence of the electron transfer rate exhibits atomic-scale variations. A two-pul…
Due to high surface to volume ratio and tunable band gap, 2 Dimensional (2D) layered materials such as MoS2, is good candidate for gas sensing applications. This research mainly focuses on variation of Density of States (DOS) of MoS2 nanosheets caused by ethanol adsorption. The nanosheets are synthesized by liquid exfoliation, and then using Scanning Tunneling Spectroscopy (STS) and Density Functional Theory (DFT), local electronic characteristic such as DOS and band gap in non-vacuum condition are analyzed. The results show that ethanol adsorption enhances DOS and deform orbitals near the val…
In this work, systematic constant-bias, variable-current scanning tunneling microscopy (STM) measurements and STM simulations from density-functional theory are made, yielding critical insights into the spatial structure of electrons in graphene. A foundational comparison is drawn between graphene and graphite, showing the surface charge density of graphene to be 300 percent that of graphite. Furthermore, simulated STM images reveal that high-current STM better resolves graphenes honeycomb bonding structure because of a retraction which occurs in the topmost dangling bond orbitals.
The results of scanning tunneling microscopy experiments using iron-coated tungsten tips and current-carrying bismuth selenide ($Bi_2Se_3$) samples are reported. Asymmetry in tunneling currents with respect to the change in the direction of bias currents through $Bi_2Se_3$ samples has been observed. It is argued that this asymmetry is the manifestation of surface spin-polarized electron accumulation caused by the ninety-degree electron spin-momentum locking in the topologically protected surface current mode. It is demonstrated that the manifestation of surface spin-polarized electron accumula…
Scanning tunneling microscopy (STM) gives us the opportunity to map the surface of functionalized carbon nanotubes in an energy resolved manner and with atomic precision. But this potential is largely untapped, mainly due to sample stability issues which inhibit reliable measurements. Here we present a simple and straightforward solution that makes away with this difficulty, by incorporating the functionalized multiwalled carbon nanotubes (MWCNT) into a few layer graphene - nanotube composite. This enabled us to measure energy resolved tunneling conductance maps on the nanotubes, which shed li…
The detection of fluorescence with submolecular resolution enables the exploration of spatially varying photon yields and vibronic properties at the single-molecule level. By placing individual polycyclic aromatic hydrocarbon molecules into the plasmon cavity formed by the tip of a scanning tunneling microscope and a NaCl-covered Ag(111) surface, molecular light emission spectra are obtained that unravel vibrational progression. In addition, light spectra unveil a signature of the molecule even when the tunneling current is injected well separated from the molecular emitter. This signature exh…
We performed spin-polarized scanning tunneling spectroscopy on biatomic-layer-high Co nanoislands grown on Cu(111) in magnetic fields oriented normal to the sample surface, with Fe-coated W tips. Increasing the temperature from 10 to 30 K, we observe a reduced slope of the differential conductance around zero field. A quantitative analysis of the field- and temperature-dependent differential conductance data in the framework of superparamagnetism as described by a Langevin function gives an excellent description of the experimental results. The analysis suggests that a Fe nano-apex at the W ti…
Single layer graphene islands with a typical diameter of several nanometers were grown on a Pt (111) substrate. Scanning tunneling microscopy (STM) analysis showed most of islands are hexagonally shaped and the zigzag-type edge predominates over the armchair-type edge. The apparent height at the atoms on the zigzag edge is enhanced with respect to the inside atoms for a small sample bias voltage, while such an enhancement was not observed at the atoms on the armchair edge. This result provides an experimental evidence of spatially (at the zigzag edge) and energetically (at the Fermi level) loc…
We have studied the superconducting Si(111)-(root7xroot3)-In surface using a 3He-based low-temperature scanning tunneling microscope (STM). Zero-bias conductance (ZBC) images taken over a large surface area reveal that vortices are trapped at atomic steps after magnetic fields are applied. The crossover behavior from Pearl to Josephson vortices is clearly identified from their elongated shapes along the steps and significant recovery of superconductivity within the cores. Our numerical calculations combined with experiments clarify that these characteristic features are determined by the relat…
The Scanning Tunneling Microscope is a powerful tool for studying the electronic properties at the atomic level, however it's relatively small scanning range and the fact that it can only operate on conducting samples prevents its application to study heterogeneous samples consisting on conducting and insulating regions. Here we present a long-range scanning tunneling microscope capable of detecting conducting micro and nanostructures on insulating substrates using a technique based on the capacitance between the tip and the sample and performing STM studies.
We present a method to identify distinct tunneling modes in tunable superconducting tunnel junction composed of superconducting tip and sample in scanning tunneling microscope. Combining the measurement of the relative decay constant of tunneling current extracted from I-V-z spectroscopy with its statistical analysis over the atomic disorders in the sample surface, we identified the crossover of tunneling modes between single quasiparticle tunneling, multiple Andreev reflection, and Josephson tunneling with respect to the bias voltage. The method enables one to determine the particular tunneli…
Nanoscale lithography on SrRuO3 (SRO) thin film surfaces has been performed by scanning tunneling microscopy under ambient conditions. The depth of etched lines increases with increasing bias voltage but it does not change significantly by increasing the tunneling current. The dependence of line width on bias voltage from experimental data is in agreement with theoretical calculation based on field-induced evaporation. Moreover, a three-square nanostructure was successfully created, showing the capability of fabricating nanodevices in SRO thin films.
The integration of a scanning tunneling microscope chamber with a sample growth facility using non-custom, commercially available parts is described. The facility also features a newly-designed magnetic wobble stick to increase the reliability of sample transfer in a cost-effective manner.
The scanning-tunneling-microscope-induced luminescence emerges recently as an incisive tool to measure the molecular properties down to the single-molecule level. The rapid experimental progress is far ahead of the theoretical effort to understand the observed phenomena. Such incompetence leads to a significant difficulty in quantitatively assigning the observed feature of the fluorescence spectrum to the structure and dynamics of a single molecule. This letter is devoted to reveal the microscopic origin of the molecular excitation via inelastic scattering of the tunneling electrons in scannin…
Graphene nanopatterning on highly oriented pyrolytic graphite (HOPG) has previously been shown using both atomic force microscopy (AFM) and scanning tunneling microscopy (STM) based techniques, including folding of intrinsic step edges and electrochemical etching or cutting in graphene layers. We here report development of a new technique, combining electrochemical etching and folding using mechanical STM manipulation. Our technique shows unprecedented control of nanoscale folding of graphene in multiple folding steps and could be a route towards STM study of magic angle graphene with in-situ …
We demonstrate rotational excitation spectroscopy with the scanning tunneling microscope for physisorbed hydrogen and its isotopes hydrogen-deuterid and deuterium. The observed excitation energies are very close to the gas phase values and show the expected scaling with moment of inertia. Since these energies are characteristic for the molecular nuclear spin states we are able to identify the para and ortho species of hydrogen and deuterium, respectively. We thereby demonstrate nuclear spin sensitivity with unprecedented spatial resolution.
Nickel islands are grown on W(110) at elevated temperatures. Islands with a thickness of two layers are investigated with scanning tunneling microscopy. Spectroscopic measurements reveal that nanometer sized areas of the islands exhibit distinctly different apparent heights and dI/dV spectra. Spin polarized and paramagnetic band structure calculations indicate that the spectral features are due to fcc(111) and bcc(110) orientations of the Ni film, respectively.
Au-induced atomic wires on the Ge(001) surface were recently claimed to be an ideal 1D metal and their tunneling spectra were analyzed as the manifestation of a Tomonaga-Luttinger liquid (TLL) state. We reinvestigate this system for atomically well-ordered areas of the surface with high resolution scanning tunneling microscopy and spectroscopy (STS). The local density-of-states maps do not provide any evidence of a metallic 1D electron channel along the wires. Moreover, the atomically resolved tunneling spectra near the Fermi energy are dominated by local density-of-states features, deviating …
The qPlus sensor allows simultaneous measurements of scanning tunneling microscopy (STM) and atomic force microscopy (AFM). Its design for use in frequency modulation AFM (FM-AFM) involves separate electrodes, applied on an oscillating quartz cantilever, for the detection of an electronic tunneling current and the deflection signal. Cable resistance and capacities in the electronic setup can induce cross talk phenomena. We report a tunneling current-induced cross coupling observed in a combined STM/AFM setup which uses the qPlus sensor. This cross coupling can induce a positive or negative cha…
The conductance-voltage spectrum of molecular nanostructures measured by scanning tunneling spectroscopy (STS) is generally assumed to reflect the local density of states of the molecule. This excludes the possibility of observing negative differential resistance (NDR). We report here the observation of NDR in the scanning tunneling microscope (STM) current-voltage (I-V) characteristics of self-assembled monolayer (SAM) of 4-p-Terphenylthiol molecules on gold substrate measured using a platinum probe. We argue that the NDR arises from narrow structures in the local density of states at the tip…
The effect of hydrogenation on the topography and the electronic properties of graphene and graphite surfaces are studied by scanning tunneling microscopy and spectroscopy. The surfaces are chemically modified using Ar/H2 plasma. Analyzing thousands of scanning tunneling spectroscopy measurements we determine that the hydrogen chemisorption on the surface of graphite/graphene opens on average an energy band gap of 0.4 eV around the Fermi level. We find that although the plasma treatment modifies the surface topography in a non-reversible way, the change in the electronic properties can be reve…
In this paper we demonstrate atomic-scale lithography on hydrogen terminated Ge(001. The lithographic patterns were obtained by selectively desorbing hydrogen atoms from a H resist layer adsorbed on a clean, atomically flat Ge(001) surface with a scanning tunneling microscope tip operating in ultra-high vacuum. The influence of the tip-to-sample bias on the lithographic process have been investigated. Lithographic patterns with feature-sizes from 200 nm to 1.8 nm have been achieved by varying the tip-to-sample bias. These results open up the possibility of a scanning-probe lithography approach…
We report a reproducible technique for the fabrication of sharp superconducting Nb tips for scanning tunneling microscopy (STM) and scanning tunneling spectroscopy. Sections of Nb wire with 250 $μ$m diameter are dry etched in an SF$_6$ plasma in a Reactive Ion Etcher. The gas pressure, etching time and applied power are chosen to produce a self-sharpening effect to obtain the desired tip shape. The resulting tips are atomically sharp, with radii of less than 100 nm, and generate good STM images and spectroscopy on single crystal samples of Au(111), Au(100), and Nb(100), as well as a doped topo…
The growth and atomic/electronic structure of molecular beam epitaxy (MBE)-grown ErAs nanoparticles and nanorods embedded within a GaAs matrix are examined for the first time via cross-sectional scanning tunneling microscopy (XSTM) and spectroscopy (XSTS). Cross sections enable the interrogation of the internal structure and are well suited for studying embedded nanostructures. The early stages of embedded ErAs nanostructure growth are examined via these techniques and compared with previous cross sectional TEM work. Tunneling spectroscopy I(V) for both ErAs nanoparticles and nanorods was also…
