The performance limits of the multilayer graphene nanoribbon (GNR) field-effect transistor (FET) are assessed and compared to those of monolayer GNR FET and carbon nanotube (CNT) FET. The results show that with a thin high-k gate insulator and reduced interlayer coupling, multilayer GNR FET can significantly outperform its CNT counterpart with a similar gate and bandgap in terms of the ballistic on-current. In the presence of optical phonon scattering, which has a short mean free path in the graphene-derived nanostructures, the advantage of the multilayer GNRFET is even more significant. The simulation results indicate multilayer GNRs with incommensurate non-AB stacking and weak interlayer coupling are the best candidate for high performance GNR FETs.
Graphene nanoribbon (GNR) field-effect transistors (FETs) with widths down to 12 nm have been fabricated by electron beam lithography using a wafer-scale chemical vapor deposition (CVD) process to form the graphene. The GNR FETs show drain-current modulation of approximately 10 at 300 K, increasing to nearly 106 at 4 K. The strong temperature dependence of the minimum current indicates the opening of a bandgap for CVD-grown GNR-FETs. The extracted bandgap is estimated to be around 0.1 eV by differential conductance methods. This work highlights the development of CVD-grown large-area graphene …
We present an atomistic three-dimensional simulation of graphene nanoribbon field effect transistors (GNR-FETs), based on the self-consistent solution of the 3D Poisson and Schroedinger equation with open boundary conditions within the non-equilibrium Green's Function formalism and a tight-binding hamiltonian. With respect to carbon nanotube FETs, GNR-FETs exhibit comparable performance, reduced sensitivity on the variability of channel chirality, and similar leakage problems due to band-to-band tunneling. Acceptable transistor performance requires effective nanoribbon width of 1-2 nm, that co…
We report on the experimental demonstration and electrical characterization of N = 7 armchair graphene nanoribbon (7-AGNR) field effect transistors. The back-gated transistors are fabricated from atomically precise and highly aligned 7-AGNRs, synthesized with a bottom-up approach. The large area transfer process holds the promise of scalable device fabrication with atomically precise nanoribbons. The channels of the FETs are approximately 30 times longer than the average nanoribbon length of 30 nm to 40 nm. The density of the GNRs is high, so that transport can be assumed well-above the percol…
We propose an analytical device model for a graphene nanoribbon field-effect transistor (GNR-FET). The GNR-FET under consideration is based on a heterostructure which consists of an array of nanoribbons clad between the highly conducting substrate (the back gate) and the top gate controlling the dc and ac source-drain currents. Using the model developed, we derive explicit analytical formulas for the GNR-FET transconductance as a function of the signal frequency, collision frequency of electrons, and the top gate length. The transition from the ballistic and to strongly collisional electron tr…
The effects of edge irregularity and mixed edge shapes on the characteristics of graphene nanoribbon transistors are examined by self-consistent atomistic simulations based on the non-equilibrium Green's function formalism. The minimal leakage current increases due to the localized states induced in the band gap, and the on-current decreases due to smaller quantum transmission and the self-consistent electrostatic effect in general. Although the ratio between the on-current and minimal leakage current decreases, the transistor still switches even in the presence of edge roughness. The variatio…
We have studied quantum transport in Graphene Nanoribbon Tunnel Field-Effect Transistors. Unlike other studies on similar structures, we have included dissipative processes induced by inelastic electron-phonon scattering and edge roughness in the nanoribbon self-consistently within a non-equilibrium transport simulation. Our results show that the dissipative scattering imposes a limit to the minimum OFF current and a minimum subthreshold swing that can be obtained even for long channel lengths where direct source-drain tunneling is inhibited. The edge roughness, in presence of dissipative scat…
We study field effect transistor characteristics in etched single layer MoS2 nanoribbon devices of width 50nm with ohmic contacts. We employ a SF6 dry plasma process to etch MoS2 nanoribbons using low etching (RF) power allowing very good control over etching rate. Transconductance measurements reveal a steep sub-threshold slope of 3.5V/dec using a global backgate. Moreover, we measure a high current density of 38 uA/um resulting in high on/off ratio of the order of 10^5. We observe mobility reaching as high as 50 cm^2/V.s with increasing source-drain bias.
It is usually assumed that tunneling current is fairly independent of temperature. By performing an atomistic transport simulation, we show, to the contrary, that the subthreshold tunneling current in a graphene nanoribbon (GNR) band-to-band tunneling transistor (TFET) should show significant and non-linear temperature dependence. Furthermore, the nature of this non-linearity changes as a function of source/drain doping and vertical electric field, indicating that such non-linearity, if properly understood, may provide important insights into the tunneling phenomena. Finally, by developing a p…
We present an analytical device model for a field-effect transistor based on a heterostructure which consists of an array of nanoribbons clad between the highly conducting substrate (the back gate) and the top gate controlling the source-drain current. The equations of the model of a graphene nanoribbon field-effect transistor (GNR-FET) include the Poisson equation in the weak nonlocality approximation. Using this model, we find explicit analytical formulas for the spatial distributions of the electric potential along the channel and for the GNR-FET current-voltage characteristics (the depende…
Mode space approach has been used so far in NEGF to treat phonon scattering for computational efficiency. Here we perform a more rigorous quantum transport simulation in real space to consider interband scatterings as well. We show a seamless transition from ballistic to dissipative transport in graphene nanoribbon transistors by varying channel length. We find acoustic phonon (AP) scattering to be the dominant scattering mechanism within the relevant range of voltage bias. Optical phonon scattering is significant only when a large gate voltage is applied. In a longer channel device, the contr…
Sub-10nm wide graphene nanoribbon field-effect transistors (GNRFETs) are studied systematically. All sub-10nm GNRs afforded semiconducting FETs without exception, with Ion/Ioff ratio up to 10^6 and on-state current density as high as ~2000uA/um. We estimated carrier mobility ~200cm2/Vs and scattering mean free path ~10nm in sub-10nm GNRs. Scattering mechanisms by edges, acoustic phonon and defects are discussed. The sub-10nm GNRFETs are comparable to small diameter (d<=~1.2nm) carbon nanotube FETs with Pd contacts in on-state current density and Ion/Ioff ratio, but have the advantage of produc…
We investigate the role of various structural nonidealities on the performance of armchair-edge graphene nanoribbon field effect transistors (GNRFETs). Our results show that edge roughness dilutes the chirality dependence often predicted by theory but absent experimentally. Instead, GNRs are classifiable into wide (semi-metallic) vs narrow (semiconducting) strips, defining thereby the building blocks for wide-narrow-wide all-graphene devices and interconnects. Small bandgaps limit drain bias at the expense of band-to-band tunneling in GNRFETs. We outline the relation between device performance…
The effect of the uniaxial strain on the current-voltage characteristic of a typical armchair graphene-nanoribbon-hBN heterostructure device is simulated numerically by employing the nearest-neighbor tight-binding model and the non-equilibrium Green's function formalism. Simulations clearly reveal the following notable dependencies: (i) the strain invariably reduces the current; (ii) the strain applied in the armchair direction markedly widens the main peak of the current over a larger region of the bias voltage compared with the unstrained state; (iii) the current decreases faster when the st…
We investigate the effects of a perpendicular electric field applied to multilayer phosphorene nanoribbons with zigzag and armchair edges. Within the context of the tight-binding model, we explore the electronic properties of these systems giving emphasis to the appearance of Dirac-like spectra, a transition that occurs when the gate density associated with the applied displacement field is greater than the critical value $n_c$. We show that the confinement properties and the screening effects in such systems play an important role on the determination of $n_c$, suggesting a scheme to determin…
Using non-equilibrium molecular dynamics method(NEMD), we have found that the thermal conductivity of multilayer graphene nanoribbons monotonously decreases with the increase of the number of layers, such behavior can be attributed to the phonon resonance effect of out-of-plane phonon modes. The reduction of thermal conductivity is found to be proportional to the layer size, which is caused by the increase of phonon resonance. Our results are in agreement with recent experiment on dimensional evolution of thermal conductivity in few layer graphene.
Silicene (a monolayer of silicon atoms) is a quantum spin-Hall insulator, which undergoes a topological phase transition into other insulators by applying external field such as electric field, photo-irradiation and antiferromagnetic order. We investigate the electronic and transport properties of silicene nanoribbons based on the Landauer formalism. We propose to determine topological phase transitions by measuring the density of states and conductance. The conductance is quantized and changes its value when the system transforms into different phases. We show that a silicene nanoribbon near …
We study the effect of transversal electric-field (E-field) on the electronic properties of multilayer armchair-graphene-nanoribbon (AGNR). The bandgap in multilayer-AGNRs can be reversibly modulated with the application of E-field. At optimized widths, we obtain a semiconductor (SC) to metallic (M), as well as M-SC transition. The AGNR electronic bands undergo vivid transformations due to the E-field, leading to phenomena such as increase in electron velocity, change in the sign of the electron effective mass, and the formation of linear dispersion with massless Dirac fermions similar to 2D-g…
We present a microscopic theory for interacting graphene armchair nanoribbon quantum dots. Long range interaction processes are responsible for Coulomb blockade and spin-charge separation. Short range ones, arising from the underlying honeycomb lattice of graphene, smear the spin-charge separation and induce exchange correlations between bulk electrons - delocalized on the ribbon - and single electrons localized at the two ends. As a consequence, entangled end-bulk states where the bulk spin is no longer a conserved quantity occur. Entanglement's signature is the occurrence of negative differe…
We study the channel width scaling of back-gated MoS2 metal-oxide-semiconductor field-effect transistors (MOSFETs) from 2 μm down to 60 nm. We reveal that the channel conductance scales linearly with channel width, indicating no evident edge damage for MoS2 nanoribbons with widths down to 60 nm as defined by plasma dry etching. However, these transistors show a strong positive threshold voltage (VT) shift with narrow channel widths of less than 200 nm. Our results also show that transistors with thinner channel thicknesses have larger VT shifts associated with width scaling. Devices fabricated…
Ballistic quantum transport calculations based on the non-equilbrium Green's function formalism show that field-effect transistor devices made from chevron-type graphene nanoribbons (CGNRs) could exhibit negative differential resistance with peak-to-valley ratios in excess of 4800 at room temperature as well as steep-slope switching with 6 mV/decade subtheshold swing over five orders of magnitude and ON-currents of 88$μ$A/$μ$m. This is enabled by the superlattice-like structure of these ribbons that have large periodic unit cells with regions of different effective bandgap, resulting in miniba…
Results of quantum mechanical simulations of the influence of edge disorder on transport in graphene nanoribbon metal oxide semiconductor field-effect transistors (MOSFETs) are reported. The addition of edge disorder significantly reduces ON-state currents and increases OFF-state currents, and introduces wide variability across devices. These effects decrease as ribbon widths increase and as edges become smoother. However the bandgap decreases with increasing width, thereby increasing the band-to-band tunneling mediated subthreshold leakage current even with perfect nanoribbons. These results …
Floating gate transistor is the basic building block of non-volatile flash memory, which is one of the most widely used memory gadgets in modern micro and nano electronic applications. Recently there has been a surge of interest to introduce a new generation of memory devices using graphene nanotechnology. In this paper we present a new floating gate transistor (FGT) design based on multilayer graphene nanoribbon (MLGNR) and carbon nanotube (CNT). In the proposed FGT a multilayer structure of graphene nanoribbon (GNR) would be used as the channel of the field effect transistor (FET) and a laye…
Flash memory based on floating gate transistor is the most widely used memory technology in modern microelectronic applications. We recently proposed a new concept of multilayer graphene nanoribbon (MLGNR) and carbon nanotube (CNT) based floating gate transistor design for future nanoscale flash memory technology. In this paper, we analyze the tunneling current mechanism in the proposed graphene-CNT floating gate transistor. We anticipate that the proposed floating gate transistor would adopt Fowler-Nordheim (FN) tunneling during its programming and erase operations. In this paper, we have inv…
We have fabricated suspended few layer (1-3 layers) graphene nanoribbon field effect transistors from unzipped multiwall carbon nanotubes. Electrical transport measurements show that current-annealing effectively removes the impurities on the suspended graphene nanoribbons, uncovering the intrinsic ambipolar transfer characteristic of graphene. Further increasing the annealing current creates a narrow constriction in the ribbon, leading to the formation of a large band-gap and subsequent high on/off ratio (which can exceed 104). Such fabricated devices are thermally and mechanically stable: re…
We report the realization of top-gated graphene nanoribbon field effect transistors (GNRFETs) of ~10 nm width on large-area epitaxial graphene exhibiting the opening of a band gap of ~0.14 eV. Contrary to prior observations of disordered transport and severe edge-roughness effects of GNRs, the experimental results presented here clearly show that the transport mechanism in carefully fabricated GNRFETs is conventional band-transport at room temperature, and inter-band tunneling at low temperature. The entire space of temperature, size, and geometry dependent transport properties and electrostat…
We study all-carbon-hydrogen molecular transistors where zigzag graphene nanoribbons play the role of three metallic electrodes connected to a ring-shaped 18-annulene molecule. Using the nonequilibrium Green function formalism combined with density functional theory, recently extended to multiterminal devices, we show that the proposed nanostructures exhibit exponentially small transmission when the source and drain electrodes are attached in a configuration that ensures destructive interference of electron paths around the ring. The third electrode, functioning either as an attached infinite-…
A general solution for the electrostatic potential in an atomic-thin-body (ATB) field-effect transistor geometry is presented. The effective electrostatic scaling length, λeff, is extracted from the analytical model, which cannot be approximated by the lowest order eigenmode as traditionally done in SOI-MOSFETs. An empirical equation for the scaling length that depends on the geometry parameters is proposed. It is shown that even for a thick SiO2 back oxide λeff can be improved efficiently by thinner top oxide thickness, and to some extent, with high-k dielectrics. The model is then applied to…
We study the effect of vertical electric-field (E-field) on the electronic properties of the multilayer armchair graphene nanoribbon (aGNR). Under E-field, the band structure of a bilayer aGNR undergoes interesting transformations such as change in the electron velocity, sign of the electron effective mass, band gap, the position of the band gap in the momentum space. Depending on the width of the aGNR and the applied E-field, the band gap of the aGNR may either be increased or decreased. When the applied E-field is above a critical value, the band gap of the bilayer aGNR is identical to that …
Bottom-up assembled nanomaterials and nanostructures allow for the studies of rich and unprecedented quantum-related and mesoscopic transport phenomena. However, it can be difficult to quantify the correlations between the geometrical or structural parameters obtained from advanced microscopy and measured electrical characteristics when they are made into macroscopic devices. Here, we propose a strategy to connect the nanomaterial morphologies and the device performance through a Monte Carlo device model and apply it to understand the scaling trends of bottom-up synthesized armchair graphene n…
Here, we isolate thin TiS3 ribbons, a layered direct band gap semiconductor (1.1 eV, well suited for detection all across the visible spectrum), thus far almost unexplored. We fabricate field effect transistors and study their electrical characteristics and optoelectronic properties. The measured FET characteristics show mobilities up to 2.6 cm^2/Vs and ON/OFF ratios up to 10^4. Under illumination, the TiS3 NR-FETs present an ultrahigh photoresponse of 2910 A/W and fast rise/fall times of ~4 ms. In addition, we measure cutoff frequencies (f3dB) up to 1000 Hz. The strong combination of ultrahig…
We perform a comprehensive first-principles study of the electronic properties of phosphorene nanoribbons, phosphorene nanotubes, multilayer phosphorene, and heterobilayers of phosphorene and two-dimensional (2D) transition metal dichalcogenide (TMDC) monolayer. The tensile strain and electric-field effects on electronic properties of low-dimensional phosphorene nanostructures are also investigated. Our calculations show that zigzag phosphorene nanoribbons (z-PNRs) are metals, regardless of the ribbon width while armchair phosphorene nanoribbons (a-PNRs) are semiconductors with indirect bandga…
We report on the fabrication and characterization of synthesized multiwall MoS2 nanotube (NT) and nanoribbon (NR) field-effect transistors (FETs). The MoS2 NTs and NRs were grown by chemical transport, using iodine as a transport agent. Raman spectroscopy confirms the material as unambiguously MoS2 in NT, NR, and flake forms. Transmission electron microscopy was used to observe cross sections of the devices after electrical measurements and these were used in the interpretation of the electrical measurements allowing estimation of the current density. The NT and NR FETs demonstrate n-type beha…
We study the effects of a vertical electric field on the electronic band structure and transport in multilayer phosphorene and its nanoribbons. In phosphorene, at a critical value of the vertical electric field ($E_c$), the band gap closes and the band structure undergoes a massive-to-massless Dirac fermion transition along the armchair direction. This transition is observable in quantum Hall measurements, as the power-law dependence of the Landau-level energy on the magnetic field $B$ goes from $\sim (n+1/2)B$ below $E_c$, to $\sim [(n+1/2)B]^{2/3}$ at $E_c$, to $\sim [(n+1/2)B]^{1/2}$ above …
The high field transport characteristics of nanostructured transistors based on layered materials are not only important from a device physics perspective but also for possible applications in next generation electronics. With the growing promise of layered materials as replacements to conventional silicon technology, we study here the high current density properties of the layered material titanium trisulfide (TiS3). We observe high breakdown current densities up to 1.7 10^6 A/cm^2 in TiS3 nanoribbon-based field-effect transistors which are among the highest found in semiconducting nanomateri…
Surface characterizations of an organophosphorus (OP) gas detector based on chemically functionalized silicon nanoribbon field-effect transistor (SiNR-FET) were performed by Kelvin Probe Force Microscopy (KPFM) and ToF-SIMS, and correlated with changes in the current-voltage characteristics of the devices. KPFM measurements on FETs allow (i) to investigate the contact potential difference (CPD) distribution of the polarized device as function of the gate voltage and the exposure to OP traces and, (ii) to analyze the CPD hysteresis associated to the presence of mobile ions on the surface. The C…
Effects of phonon confinement on electron transport in Si nanowire and armchair-edge graphene nanoribbon transistors: A dissipative quantum-transport study
Graphene nanoribbons (GNRs) have attracted a strong interest from researchers worldwide, as they constitute an emerging class of quantum-designed materials. The major challenges towards their exploitation in electronic applications include reliable contacting, complicated by their small size ($<$50 nm), as well as the preservation of their physical properties upon device integration. In this combined experimental and theoretical study, we report on the quantum dot (QD) behavior of atomically precise GNRs integrated in a device geometry. The devices consist of a film of aligned 5-atoms wide GNR…
Plasmon resonance in nanopatterned single layer graphene nanoribbon (SL-GNR), double layer graphene nanoribbon (DL-GNR) and triple layer graphene nanoribbon (TL-GNR) structures is studied both experimentally and by numerical simulations. We use 'realistic' graphene samples in our experiments to identify the key bottle necks in both experiments and theoretical models. The existence of electrical tunable plasmons in such stacked multilayer GNRs was first experimentally verified by infrared microscopy. We find that the strength of the plasmonic resonance increases in DL-GNR when compared to SL-GN…
With the motivation of improving the performance and reliability of aggressively scaled nano-patterned graphene field-effect transistors, we present the first systematic experimental study on charge and current distribution in multilayer graphene field-effect transistors. We find a very particular thickness dependence for Ion, Ioff, and the Ion/Ioff ratio, and propose a resistor network model including screening and interlayer coupling to explain the experimental findings. In particular, our model does not invoke modification of the linear energy-band structure of graphene for the multilayer c…
For the first time, polyethyleneimine (PEI) doping on multilayer MoS2 field-effect transistors are investigated. A 2.6 times reduction in sheet resistance, and 1.2 times reduction in contact resistance have been achieved. The enhanced electrical characteristics are also reflected in a 70% improvement in ON current, and 50% improvement in extrinsic field-effect mobility. The threshold voltage also confirms a negative shift upon the molecular doping. All studies demonstrate the feasibility of PEI molecular doping in MoS2 transistors, and its potential applications in layer-structured semiconduct…
The impact of electrostatic doping level on the dissipative transport of Armchair GNR-TFET is studied using the Quantum Perturbation Theory (QPT) with the Extended Lowest Order Expansion (XLOE) implementation method. Results show that the doping level of the source and drain sides of the GNR-TFET has a significant impact on the phonon contribution to the carrier transport process. Unlike in other similar studies, where phonons are believed to have a constant detrimental influence on the ION/IOFF ratio and Subthreshold Swing (SS) of the TFET devices due to the phonon absorption-assisted tunneli…
We present low-frequency electrical resistance fluctuations, or noise, in graphene-based field-effect devices with varying number of layers. In single-layer devices the noise magnitude decreases with increasing carrier density, which behaved oppositely in the devices with two or larger number of layers accompanied by a suppression in noise magnitude by more than two orders in the latter case. This behavior can be explained from the influence of external electric field on graphene band structure, and provides a simple transport-based route to isolate single-layer graphene devices from those wit…
Bottom-up synthesized GNRs and GNR heterostructures have promising electronic properties for high performance field effect transistors (FETs) and ultra-low power devices such as tunnelling FETs. However, the short length and wide band gap of these GNRs have prevented the fabrication of devices with the desired performance and switching behaviour. Here, by fabricating short channel (Lch ~20 nm) devices with a thin, high-k gate dielectric and a 9-atom wide (0.95 nm) armchair GNR as the channel material, we demonstrate FETs with high on-current (Ion >1 uA at Vd = -1 V) and high Ion/Ioff ~10^5 at …
In this paper, we present a mode space method for atomistic non-equilibrium Green's function simulations of armchair graphene nanoribbon FETs that includes electron-phonon scattering. With reference to both conventional and tunnel FET structures, we show that, in the ideal case of a smooth electrostatic potential, the modes can be decoupled in different groups without any loss of accuracy. Thus, inter-subband scattering due to electron-phonon interactions is properly accounted for, while the overall simulation time considerably improves with respect to real-space, with a speed-up factor of 40 …
Using the tight binding and Pariser-Parr-Pople (PPP) model Hamiltonians, we study the electronic structure and optical response of multilayer armchair graphene nanoribbons (AGNRs), both with and without a gate bias. In particular, the influence of the number of layers ($n$), and the strength of the electric field applied perpendicular to layers, for different types of edge alignments, is explored on their electro-optical properties. As a function of increasing $n$, the energy gap initially decreases, eventually saturating for large $n$. The intensity of the linear optical absorption in these s…
We report the realization of field-effect transistors (FETs) made with chemically synthesized multilayer 2D crystal semiconductor MoS2. Electrical properties such as the FET mobility, subthreshold swing, on/off ratio, and contact resistance of chemically synthesized (s-) MoS2 are indistinguishable from that of mechanically exfoliated (x-) MoS2, however flat-band voltages are different, possibly due to polar chemical residues originating in the transfer process. Electron diffraction studies and Raman spectroscopy show the structural similarity of s-MoS2 to x-MoS2. This initial report on the beh…
A heterojunction tunneling field effect transistor based on armchair graphene nanoribbons is proposed and studied using ballistic quantum transport simulation based on 3D real space nonequilibrium Green's function formalism. By using low band gap nanoribbons as the source/drain material, the hetero- structure shows better performance including higher on current, lower off current, and improved steep subthreshold swings compared with homostructure. It is also found the device performance greatly depends on the source/drain dopping density. High doping density leads to fewer density states in th…
Phosphorene, a honeycomb structure of black phosphorus, was isolated recently. We investigate electric properties of phosphorene nanoribbons based on the tight-binding model. A prominent feature is the presence of quasi-flat edge bands entirely detached from the bulk band. We explore the mechanism of the emergence of the quasi-flat bands analytically and numerically from the flat bands well known in graphene by a continuous deformation of a honeycomb lattice. The quasi-flat bands can be controlled by applying in-plane electric field perpendicular to the ribbon direction. The conductance is swi…
In graphene nanoribbons (GNRs), the lateral confinement of charge carriers opens a band gap, the key feature to enable novel graphene-based electronics. Successful synthesis of GNRs has triggered efforts to realize field-effect transistors (FETs) based on single ribbons. Despite great progress, reliable and reproducible fabrication of single-ribbon FETs is still a challenge that impedes applications and the understanding of the charge transport. Here, we present reproducible fabrication of armchair GNR-FETs based on a network of nanoribbons and analyze the charge transport mechanism using nine…
Semiconducting two-dimensional transition metal chalcogenide crystals have been regarded as the promising candidate for the future generation of transistor in modern electronics. However, how to fabricate those crystals into practical devices with acceptable performance still remains as a challenge. Employing tungsten disulfide multilayer thin crystals, we demonstrate that using gold as the only contact metal and choosing appropriate thickness of the crystal, high performance transistor with on/off ratio of $10^{8}$ and mobility up to $234\:cm^{2}V^{-1}s^{-1}$ at room temperature can be realiz…
A tunneling field effect transistor based on armchair graphene nanoribbons is studied using ballistic quantum transport simulation based on 3D real space nonequilibrium Green's function formalism. By introducing a pocket doping region near the source, the performance of GNRs TFET is improved in terms of larger on current and steeper subthreshold swings compared to conventional tunneling FET. It is also found that pocket region introduces two interesting features. By increasing the pocket length the ambipolar can be effectively suppressed. Furthermore, there is negative trans-conductance at neg…
We report about the fabrication and analysis of the properties of Cr/CrO_x/Cr tunnel junctions and SET transistors, prepared by different variants of direct-writing multilayer technique. In all cases, the CrO_x tunnel barriers were formed in air under ambient conditions. From the experiments on single junctions, values for the effective barrier height and thickness were derived. For the Cr/CrO_x/Cr SET transistors we achieved minimal junction areas of 17 x 60 nm^2 using a scanning transmission electron microscope for the e-beam exposure on Si_3N_4 membrane substrate. We discuss the electrical …
Palladium diselenide (PdSe2) is a recently isolated layered material that has attracted a lot of interest for the pentagonal structure, the air stability and the electrical properties largely tunable by the number of layers. In this work, PdSe2 is used in the form of multilayer as the channel of back-gate field-effect transistors, which are studied under repeated electron irradiations. Source-drain Pd leads enable contacts with resistance below 350 kOhm um. The transistors exhibit a prevailing n-type conduction in high vacuum, which reversibly turns into ambipolar electric transport at atmosph…
We show a large magnetoresistance(MR) effect in a graphene heterostructure consisting of an metallic(M) and semiconductor(SC)-type armchair-graphene-nanoribbon(aGNR). In the heterostructure, the transmission across the first subband of the SC-aGNR and M-aGNR is forbidden under zero magnetic-field, due to the orthogonality of the wavefunctions. A finite magnetic-field introduces the quantum hall-like effect, which distorts the wavefunctions. Thus, a finite transmission occurs across the heterojunction, giving rise to a large MR effect. We study the dependence of this MR on temperature and elect…
