结果表明，众所周知的蓝移的基本吸收边的沉积组成调制的非晶Si/Ge和As 6Se 94/Se 80 Te 20多层膜（周期为4-8 nm）的进一步增强，由于热或激光诱导的相邻层的相互混合。实验和模型计算表明，As 6Se 94/Se 80 Te 20多层膜中的激光诱导混合过程是由局部加热和光效应共同作用的结果，而Si/Ge多层膜中只有热效应。基于这种增强的相互扩散的结构转变为空间图案化光电子器件和数字信息记录提供了良好的能力。
英文摘要：
It is shown that the well-known blue-shift of the fundamental absorption edge in as-deposited compositionally modulated amorphous Si/Ge and As6Se94/Se80Te20 multilayers (with periods of 4-8 nm) is further enhanced due to the thermal or laser-induced intermixing of adjacent layers. The laser-induced intermixing process, as supported by experiments and model calculations, can be attributed to both the local heating and photo-effects in As6Se94/Se80Te20 multilayers, while only the thermal effects were observed for Si/Ge multilayers. Structural transformations, based on this enhanced interdiffusion, provides good capability for spatially patterning optoelectronic devices and digital information recording.
Amorphous/crystalline multilayer structures of Fe-P alloys were deposited electrochemically using the single bath technique. Hall-Petch behavior of microhardness with respect to sublayer thickness was observed down to a sublayer thickness of 15 nm. For thinner sublayers, a hardness plateau was obtained. The transition at a sublayer thickness of 15 nm coincides with the loss of the multilayer structure as observed in transmission electron microscopy. The transition is a possible result of a change in the amorphous to crystalline sublayer thickness ratio and the interface roughness development d…
The Monte Carlo method in the canonical ensemble is used to investigate magnetization reversal in amorphous transition metal - rare earth multilayers. Our study is based on a model containing diluted clusters which exhibit an effective uniaxial anisotropy in competition with random magnetic anisotropy in the matrix. We simulate hysteresis loops for an abrupt profile and a diffuse one obtained from atom probe tomography analyses. Our results evidence that the atom probe tomography profile favors perpendicular magnetic anisotropy in agreement with magnetic measurements. Moreover, the hysteresis …
The thickness dependence of the magnetic properties of amorphous Fe90Zr10 layers has been explored using Fe90Zr10/Al75Zr25 multilayers. The Al75Zr25 layer thickness is kept at 40 Å, while the thickness of the Fe90Zr10 layers is varied between 5 and 20 Å. The thickness of the Al75Zr25 layers is sufficiently large to suppress any significant interlayer coupling. Both the Curie temperature and the spontaneous magnetization decrease non-linearly with decreasing thickness of the Fe90Zr10 layers. No ferromagnetic order is observed in the multilayer with 5 Å Fe90Zr10 layers. The variation of the Curi…
The transport response of dipole skyrmions in amorphous centrosymmetric Fe/Gd multilayer is investigated by temperature and field-dependent resistivity measurements collected in three current and magnetic field configurations. It is shown that a dipole skyrmion lattice phase may form at certain temperatures leading to a unique signature of the polar longitudinal resistivity. This signature differs from the conventional field-varying parabolic response associated with stripe phases, which transition to a disordered skyrmion phase under applied fields. Transport measurements under different fiel…
This study provides a new insight into the processes which occur when thin film hydrogenated amorphous silicon is subjected to UV laser irradiation in the presence of oxygen. It achieves this by observing the effects of subjecting the films to progressively increasing laser radiation doses. This reveals that an array of nuclei is first created, leading to the formation of a well-defined crystalline network, consistent with the structure of silicon oxide. Further irradiation results in the formation of cone-like structures on the crystalline network, due to silicon-oxygen bond breakage and migr…
The magnetization dynamics for ferrimagnets at the angular momentum compensation temperature T_A is believed to be analogous to that for antiferromagnets. We investigated the pulsed-laser-induced magnetization dynamics in amorphous rare-earth transition-metal ferrimagnet films with a T_A just above room temperature. For a low pulse fluence, the magnetization precession frequency decreases as the applied magnetic field increases, whereas for a higher pulse fluence, it increases as the applied field increases. The result was well explained by the left-handed and right-handed precession modes of …
The dynamic response of dipole skyrmions in Fe/Gd multilayer films is investigated by ferromagnetic resonance measurements and compared to micromagnetic simulations. We detail thickness and temperature dependent studies of the observed modes as well as the effects of magnetic field history on the resonant spectra. Correlation between the modes and the magnetic phase maps constructed from real-space imaging and scattering patterns allows us to conclude the resonant modes arise from local topological features such as dipole skyrmions but does not depend on the collective response of a closed pac…
In this paper we demonstrate experimentally that crystalline phases appear in amorphous titanium oxide upon processing with ultrafast laser pulses. Amorphous titanium thin films were produced by plasma-enhanced chemical vapor deposition (PECVD) and exposed to femtosecond laser pulses. Formation of rutile phase was confirmed by X-ray diffraction, Raman measurements and electron backscattering diffraction. A rang of processing parameters for the crystallization is reported and possible background mechanisms are discussed.
Annealing of crystalline multilayers composed of two miscible elements usually causes interfacial mixing of the constituent atoms, possibly leading to the formation of binary alloys at the interfaces. Magnetron sputtered c-Ni/a-Zr multilayers deposited at room temperature were vacuum annealed isochronally at 200degC and 400degC to observe thermal stability of the interfaces constituting the crystalline/amorphous multilayers. Control over the interfacial behaviour can aid the formation of materials with novel properties. The resultant changes in structural and magnetic properties of the multila…
Pulsed Laser Deposition allows to obtain W and W-Ta alloy coatings with different nanostructures, monitored by X-ray diffraction. The correlation between such structures and the elastic properties is investigated for amorphous-like, ultra-nano- and nano-crystalline coatings obtained by tuning the gas pressure during deposition, annealing temperature and Ta concentration. The full elastic characterization is achieved by surface Brillouin spectroscopy, interpreted by isotropic and anisotropic film models. Amorphous like coatings are obtained with He pressures of tens of Pa. In comparison with bu…
The amorphous-to-crystalline transition in Al(1.0%wtSi)/Zr and Al(Pure)/Zr multilayers grown by direct-current magnetron sputtering system has been characterized over a range of Al layer thicknesses (1.0-5.0 nm) by using a series of complementary measurements including grazing incidence X-ray reflectometry, atomic force microscopy, X-ray diffraction and high-resolution transmission electron microscopy. The Al layer thickness transition exhibits the Si doped in Al could not only disfavor the crystallization of Al, but also influence the changing trends of surface roughness and diffraction peak …
Laser induced crystal nucleation through optical tweezing, and in particular polymorph selection through laser polarization, promises unprecedented control over crystallization. However, in the absence of a nearby liquid liquid critical point or miscibility gap, the origin of the required mesoscale clusters remains unclear. A number of recent studies of so called nonclassical nucleation have suggested the presence of large amorphous clusters. Here we show that supersaturated aqueous glycine solutions form metastable intermediate particles that are off the direct path to crystal nucleation. Las…
We deposit intrinsic hydrogenated amorphous silicon (a-Si:H) thin films by reactive pulsed laser deposition, for various hydrogen pressures in the 0-20 Pa range, at a low deposition temperature of 120C, and investigate the hydrogen incorporation, structural, optical, and electrical properties of the films, as a function of the ambient hydrogen pressure. The film thickness decreases linearly as the hydrogen pressure increases. The hydrogen content of the films is determined by infrared spectroscopy and the optical bandgap from UV-Vis-NIR transmittance and reflectance measurements. Electric meas…
Visible luminescence is observed from the composite of SiO2 with embedded silicon nanocrystallites produced by femtosecond laser irradiation of hydrogenated amorphous silicon (a-Si:H) film in air. The photoluminescence originates from the defect states at the interface between silicon crystallites and SiO2 matrix. The method could be used for fabrication of luminescent layers to increase energy conversion of a-Si:H solar cells.
We present the results on excimer laser modification and patterning of amorphous vanadium pentoxide films. Wet positive resist-type and Ar ion-beam negative resist-type etching techniques were employed to develop UV-modified films. V2O5 films were found to possess sufficient resistivity compared to standard electronic materials thus to be promising masks for sub-micron lithog-raphy
Single Pulse All Optical Helicity Independent Switching (AO-HIS) represents the ability to reverse the magnetic moment of a nanostructure using a femtosecond single laser pulse. It is an ultrafast method to manipulate magnetization without the use of any applied field. Since the first switching experiments carried on GdFeCo ferrimagnetic systems, single pulse AO-HIS has been restricted for a while to Gd-based alloys or Gd/FM bilayers where FM is a ferromagnetic layer. Only recently has AO-HIS been extended to a few other materials: MnRuGa ferrimagnetic Heusler alloys and Tb/Co multilayers with…
Operando Characterization of Volume Changes in Lithium-Ion Battery Electrodes during Cycling using Isotope Multilayers
Clausthal University of Technology（克莱斯特大学）；Clausthal Center for Materials Technology（克莱斯特材料技术中心）；Center for Neutron and Muon Sciences, Paul Scherer Institute（保罗谢勒研究所中子与缪子科学中心）
The effect of increasing temperature on the structural stability and interactions of two kinds of Al/Zr (Al(1%wtSi)/Zr and Al(Pure)/Zr) multilayer mirrors are investigated. All Al/Zr multilayers annealed from 200^{\circ}C to 500^{\circ}C, were deposited on Si wafers by using direct-current magnetron sputtering technology. A detailed and consistent picture of the thermally induced changes in the microstructure is obtained using an array of complementary measurements including grazing incidence X-ray reflectance, atomic force microscope, X-ray diffraction and high-resolution transmission electro…
We examine the atomic intermixing phenomenon in three distinct amorphous CoB-based multilayer thin film platforms - Pt/CoB/Ir, Ir/CoB/Pt and Pt/CoB/MgO - which are shown to stabilise room-temperature chiral magnetic textures. Intermixing occurs predominantly between adjacent metallic layers. Notably, it is stack-order dependent, and particularly extensive when Ir sits atop CoB. Intermixing induced variations in magnetic properties are ascribed to the formation of magnetic dead layer arising from CoIr alloying in the metallic stacks. It also produces systematic variations in saturation magnetiz…
A femtosecond laser-irradiated crystallizing technique is tried to convert amorphous Sb2Te3 film into crystalline film. Sensitive coherent phonon spectroscopy (CPS) is used to monitor the crystallization of amorphous Sb2Te3 film at the original irradiation site. The CPS reveals that the vibration strength of two phonon modes that correspond to the characteristic phonon modes of crystalline Sb2Te3, enhances with increasing laser irradiation fluence (LIF), showing the rise of the degree of crystallization with LIF and that femtosecond laser irradiation is a good post-treatment technique. Time-re…
The thermal properties of amorphous and crystalline phases in chalcogenide phase change materials (PCM) play a key role in device performance for non-volatile random-access memory. Here, we report the nanothermal morphology of amorphous and crystalline phases in laser pulsed GeTe and Ge2Sb2Te5 thin films by scanning thermal microscopy (SThM). By performing SThM measurements and applying quantitative physical models to two film thicknesses, the PCM thermal conductivities and thermal boundary conductances between the PCM and SThM probe are independently estimated for the amorphous and crystallin…
The Cu/Fe/Pd multilayers were transformed into L10-ordered FePdCu alloy by pulsed laser annealing. The initial multilayers were irradiated with 1, 10, 100, and 1000 laser pulses with duration time of 10 ns and energy density of 235 mJ/cm2. The gradual change of the number of laser pulses allowed to investigate the structural and magnetic properties at early stages of the transformation and L10-ordering processes. The measurements were carried out using X-Ray Diffraction, SQUID magnetometry, and Magnetic Force Microscopy. We found that L10 FePdCu (111)-oriented nanograins are formed by ordering…
We report on Boron diffusion and subsequent crystallization of Co$_{40}$Fe$_{40}$B$_{20}$ (CoFeB) thin films on SiO$_2$/Si(001) substrate using pulsed laser deposition. Secondary ion mass spectroscopy reveals Boron diffusion at the interface in both amorphous and crystalline phase of CoFeB. High-resolution transmission electron microscopy reveals a small fraction of nano-crystallites embedded in the amorphous matrix of CoFeB. However, annealing at 400$^\circ$C results in crystallization of CoFe with \textit{bcc} structure along (110) orientation. As-deposited films are non-metallic in nature w…
Monatomic antimony thin films have recently attracted attention for applications in phase change memory, nanophotonics, and 2D materials. Although some promising results have been reported, the true potential of Sb thin films is still hindered by the scalability issue and the lack of reliable bottom-up production. Here we demonstrate the growth of Sb thin films on a lattice-matching and amorphous substrates using pulsed laser deposition (PLD). C-axis out-of-plane textured Sb thin films were successfully deposited on Sb$_2$Te$_3$ and SiO$_2$\Si$_3$N$_4$ substrates. In the case of growth on Sb$_…
We use transient absorption spectroscopy with circularly polarized x-rays to detect laser-excited hole states below the Fermi level and compare their dynamics with that of unoccupied states above the Fermi level in ferromagnetic [Co/Pd] multilayers. While below the Fermi level an instantaneous and significantly stronger demagnetization is observed, above the Fermi level the demagnetization is delayed by 35+/-10 fs. This provides a direct visualization of how ultrafast demagnetization proceeds via initial spin-flip scattering of laser-excited holes to the subsequent formation of spin waves.
Hyperbolic metamaterials show exceptional optical properties, such as near-perfect broadband absorption, due to their geometrically-engineered optical anisotropy. Many of their proposed applications, such as thermophotovoltaics or radiative cooling, require high-temperature stability. In this work we examine Ag/a-Si multilayers as a model system for the thermal stability of hyperbolic metamaterials. Using a combination of nanotomography, finite element simulations and optical spectroscopy, we map the thermal and optical instability of the metamaterials. Although the thermal instability initiat…
Laser-Synthesized Amorphous PdSe$_{\mathrm{2-x}}$ Nanoparticles: A Defect-Rich Platform for High-Efficiency SERS, Photocatalysis, and Photothermal Conversion
Electronic excitations in a ferromagnet can trigger ultrafast spin dynamics with potential applications in a speed increase in magnetic recording. The project investigates ultrafast magnetization dynamics, which is driven in metallic layers by ballistic hot electrons. In a ferromagnet these electrons induce a change in the absolute value of the magnetization M through spin-dependent scattering. If the electrons are spin-polarized, scattering at the interface of a noble metal and a ferromagnet results in spin-transfer torque and hence modifies the direction of M. To reveal the underlying mechan…
The irradiation with the 10 ns pulsed infrared Nd:YAG laser was applied to transform FePdCu multilayers into chemically ordered L10 phase. The X-ray diffraction methods (Theta/2Theta scan, psi-scan, omega-scan) were used to trace the presence of L10 phase after laser annealing with different number of pulses. The size and shape of crystallites was determined depending on their orientation with respect to film plane. The (111) oriented crystallites of constituent metals were built as coherent domains spreading through multilayers during deposition of films. Laser annealing induced the transform…
Facilitating electrical and laser-induced skyrmion nucleation with a dipolar-field enhanced effective DMI
Eindhoven University of Technology（埃因霍温理工大学）；Radboud University Nijmegen, Institute for Molecules and Materials（奈梅亨拉德堡德大学分子与材料研究所）；NT-MDT BV（NT-MDT有限公司）
We demonstrate that the intrinsic properties of monolayer graphene allow it to act as a more effective saturable absorber for mode-locking fiber lasers compared to multilayer graphene. The absorption of monolayer graphene can be saturated at lower excitation intensity compared to multilayer graphene, graphene with wrinkle-like defects, and functionalized graphene. Monolayer graphene has a remarkable large modulation depth of 95.3%, whereas the modulation depth of multilayer graphene is greatly reduced due to nonsaturable absorption and scattering loss. Picoseconds ultrafast laser pulse (1.23 p…
The paper presents a new approach, based on controlled oxidation of nanoscale metallic multilayers, to produce strong and hard oxide/metal nanocomposite coatings with high strength and good thermal stability. The approach is demonstrated by performing long term annealing on sputtered Zr/Nb nanoscale metallic multilayers and investigating the evolution of their microstructure and mechanical properties by combining analytical transmission electron microscopy, nano-mechanical tests and finite element models. As-deposited multilayers were annealed at 350 C in air for times ranging between 1 - 336 …
Additive solid immersion lenses for enhanced collection efficiency of shallow NV centers by pulsed laser deposition and structurization of high-k amorphous oxides
Leipzig University（莱比锡大学）；Felix Bloch Institute, Leipzig University（莱比锡大学费利克斯·布洛赫研究所）；SaxonQ GmbH（萨克森量子有限公司）；Department of Prosthetic Dentistry and Dental Material Science, Leipzig University（莱比锡大学假肢牙科与牙科材料科学系）
From pore collapse to crystal growth: ultrafast laser-induced stishovite formation in nanoporous silica
Université Jean Monnet, CNRS, Institut d’Optique Graduate School, Laboratoire Hubert Curien UMR 5516（让·莫兰大学，法国国家科学研究中心，高等光学研究院，于贝尔·居里实验室）；Department of Materials Science and Engineering, The Ohio State University（俄亥俄州立大学材料科学与工程系）
Amorphous films of tantalum oxide (Ta2O5) are widely applied to build highly reflective mirrors used in interferometric gravitational wave detectors, such as the Laser Interferometer Gravitational Wave Observatory (LIGO). Despite a large number of studies, the structural properties of amorphous Ta2O5 at the local scale still deserve several further investigations. Such information is essential to any attempt to understand the properties of this important material and no property modelling efforts can be expected to yield reliable information until the local structure in the amorphous phase is …
Simultaneous detection of THz emission and transient magneto-optical response is employed to study ultrafast laser-induced magnetization dynamics in multisublattice magnets NdFeCo and GdFeCo amorphous alloys with in-plane magnetic anisotropy. A satisfactory quantitative agreement between the dynamics revealed with the help of these two techniques is obtained for GdFeCo. For NdFeCo the THz emission reveals faster dynamics than the magneto-optical response. This indicates that in addition to spin dynamics of Fe ultrafast laser excitation triggers faster magnetization dynamics of Nd.
We have examined the effect of pump-probe photon energy on the amplitude of coherent optical phonons in a prototypical phase change material using a femtosecond time-resolved transmission technique. The photon energy was varied between 0.8 and 1.0 eV (corresponding to the wavelength of 1550 and 1200 nm), a range over which there is significant optical contrast between the crystalline and amorphous phases of Ge$_{2}$Sb$_{2}$Te$_{5}$ (GST225). It was found that in crystalline GST225 the coherent phonon amplitude monotonically increases as the photon energy increases, indicating that the phonon a…
Metals in amorphous state are promising for the use as structural materials due to their superior properties related to the absence of grain boundaries and dislocations.Obtaining the amorphous state requires quenching with a high cooling rate.In conventional technologies,this is the reason for a considerable size limitation hindering application of amorphous alloys.Additive manufacturing (AM) is free of the size limitation.The so-called bulk metallic glass (BMG) alloys have extremely low critical cooling rates and can be used in AM. Recent studies on AM from Zr-based BMGs by selective laser me…
