Wideband communications are impossible with signals that are spread over a very large band and are transmitted over multipath channels unknown ahead of time. This work exploits the I-mmse connection to bound the achievable data-rate of spreading signals in wideband settings, and to conclude that the achievable data-rate diminishes as the bandwidth increases due to channel uncertainty. The result applies to all spreading modulations, i.e. signals that are evenly spread over the bandwidth available to the communication system, with SNR smaller than log(W/L)/(W/L) and holds for communications over channels where the number of paths L is unbounded by sub-linear in the bandwidth W.
Bit-interleaved coded modulation (BICM) using (bi-)orthogonal signals is especially well suited for the application in impulse-radio ultra-wideband transmission systems, which typically operate in the power-limited regime and require a very low-complexity transmitter and receiver design. In this paper we analyze the capacity of BICM using (bi-)orthogonal signals with coherent and noncoherent detection and put particular focus on the power-limited or wideband regime. We give analytical expressions for the ratio energy per bit vs. noise power spectral density in the limit of infinite bandwidth a…
We consider the problem of adaptive modulation for wideband DS-CDMA Rayleigh fading channels with imperfect channel state information (CSI). We assume a multidimensional signal subspace spanned by a collection of random spreading codes (multicoding) and study the effects of both the subspace dimension and the probability distribution of the transmitted symbols on the mutual information between the channel input and output in the presence of uncertainty regarding the true state of the channel. We develop approximations for the mutual information as well as both upper and lower bounds on the mut…
The high time resolution of ultra-wideband (UWB) signals facilitates very precise position estimation in many scenarios, which makes a variety applications possible. This paper reviews the problem of position estimation in UWB systems, beginning with an overview of the basic structure of UWB signals and their positioning applications. This overview is followed by a discussion of various position estimation techniques, with an emphasis on time-based approaches, which are particularly suitable for UWB positioning systems. Practical issues arising in UWB signal design and hardware implementation …
When there are a large number of antennas in massive MIMO systems, the transmitted wideband signal will be sensitive to the physical propagation delay of electromagnetic waves across the large array aperture, which is called the spatial-wideband effect. In this scenario, transceiver design is different from most of the existing works, which presume that the bandwidth of the transmitted signals is not that wide, ignore the spatial-wideband effect, and only address the frequency selectivity. In this paper, we investigate spatial- and frequency-wideband effects, called dual-wideband effects, in m…
Optical communication systems, which operate at very high rates, are often limited by the sampling rate bottleneck. The optical wideband regime may exceed analog to digital converters (ADCs) front-end bandwidth. Multi-channel sampling approaches, such as multicoset or interleaved ADCs, have been proposed to sample the wideband signal using several channels. Each channel samples below the Nyquist rate such that the overall sampling rate is preserved. However, this scheme suffers from two practical limitations that make its implementation difficult. First, the inherent anti-aliasing filter of th…
Periodic nonuniform sampling is a known method to sample spectrally sparse signals below the Nyquist rate. This strategy relies on the implicit assumption that the individual samplers are exposed to the entire frequency range. This assumption becomes impractical for wideband sparse signals. The current paper proposes an alternative sampling stage that does not require a full-band front end. Instead, signals are captured with an analog front end that consists of a bank of multipliers and lowpass filters whose cutoff is much lower than the Nyquist rate. The problem of recovering the original sig…
Spectrum sensing is a fundamental component in cognitive radio. A major challenge in this area is the requirement of a high sampling rate in the sensing of a wideband signal. In this paper a wideband spectrum sensing model is presented that utilizes a sub-Nyquist sampling scheme to bring substantial savings in terms of the sampling rate. The correlation matrix of a finite number of noisy samples is computed and used by a subspace estimator to detect the occupied and vacant channels of the spectrum. In contrast with common methods, the proposedmethod does not need the knowledge of signal proper…
The Modulated Wideband Converter (MWC) is a recently proposed analog-to-digital converter (ADC) based on Compressive Sensing (CS) theory. Unlike conventional ADCs, its quantization reference voltage, which is important to the system performance, does not equal the maximum amplitude of original analog signal. In this paper, the quantization reference voltage of the MWC is theoretically analyzed and the conclusion demonstrates that the reference voltage is proportional to the square root of $q$, which is a trade-off parameter between sampling rate and number of channels. Further discussions and …
In this paper, we present a wideband subspace estimation method that characterizes the signal subspace through its orthogonal projection matrix at each frequency. Fundamentally, the method models this projection matrix as a function of frequency that can be approximated by a polynomial. It provides two improvements: a reduction in the number of parameters required to represent the signal subspace along a given frequency band and a quality improvement in wideband direction-of-arrival (DOA) estimators such as Incoherent Multiple Signal Classification (IC-MUSIC) and Modified Test of Orthogonality…
Too high sampling rate is the bottleneck to wideband spectrum sensing for cognitive radio in mobile communication. Compressed sensing (CS) is introduced to transfer the sampling burden. The standard sparse signal recovery of CS does not consider the distortion in the analogue-to-information converter (AIC). To mitigate performance degeneration casued by the mismatch in least square distortionless constraint which doesn't consider the AIC distortion, we define the sparse signal with the sampling distortion as a bounded additive noise, and An anti-sampling-distortion constraint (ASDC) is deduced…
The performance of grant-free random access (GF-RA) is limited by the number of accessible random access resources (RRs) due to the absence of collision resolution. Compressive sensing (CS)-based RA schemes scale up the RRs at the expense of increased non-orthogonality among transmitted signals. This paper presents the design of multi-sequence spreading random access (MSRA) which employs multiple spreading sequences to spread the different symbols of a user as opposed to the conventional schemes in which a user employs the same spreading sequence for each symbol. We show that MSRA provides cod…
This paper studies the ergodic capacity of wideband multipath channels with limited feedback. Our work builds on recent results that have established the possibility of significant capacity gains in the wideband/low-SNR regime when there is perfect channel state information (CSI) at the transmitter. Furthermore, the perfect CSI benchmark gain can be obtained with the feedback of just one bit per channel coefficient. However, the input signals used in these methods are peaky, that is, they have a large peak-to-average power ratios. Signal peakiness is related to channel coherence and many recen…
High time resolution of ultra wideband (UWB) signals facilitates very precise positioning capabilities based on time-of-arrival (TOA) measurements. Although the theoretical lower bound for TOA estimation can be achieved by the maximum likelihood principle, it is impractical due to the need for extremely high-rate sampling and the presence of large number of multipath components. On the other hand, the conventional correlation-based algorithm, which serially searches possible signal delays, takes a very long time to estimate the TOA of a received UWB signal. Moreover, the first signal path does…
In this paper, we introduce a wideband dictionary framework for estimating sparse signals. By formulating integrated dictionary elements spanning bands of the considered parameter space, one may efficiently find and discard large parts of the parameter space not active in the signal. After each iteration, the zero-valued parts of the dictionary may be discarded to allow a refined dictionary to be formed around the active elements, resulting in a zoomed dictionary to be used in the following iterations. Implementing this scheme allows for more accurate estimates, at a much lower computational c…
We consider a multiple-input, multiple-output (MIMO) wideband Rayleigh block fading channel where the channel state is unknown to both the transmitter and the receiver and there is only an average power constraint on the input. We compute the capacity and analyze its dependence on coherence length, number of antennas and receive signal-to-noise ratio (SNR) per degree of freedom. We establish conditions on the coherence length and number of antennas for the non-coherent channel to have a "near coherent" performance in the wideband regime. We also propose a signaling scheme that is near-capacity…
In contrast to the prevalent assumption of rich multipath in information theoretic analysis of wireless channels, physical channels exhibit sparse multipath, especially at large bandwidths. We propose a model for sparse multipath fading channels and present results on the impact of sparsity on non-coherent capacity and reliability in the wideband regime. A key implication of sparsity is that the statistically independent degrees of freedom in the channel, that represent the delay-Doppler diversity afforded by multipath, scale at a sub-linear rate with the signal space dimension (time-bandwidth…
In this paper, detection of the primary user (PU) signal in an orthogonal frequency division multiplexing (OFDM) based cognitive radio (CR) system is addressed. According to the prior knowledge of the PU signal known to the detector, three detection algorithms based on the Neyman-Pearson philosophy are proposed. In the first case, a Gaussian PU signal with completely known probability density function (PDF) except for its received power is considered. The frequency band that the PU signal resides is also assumed known. Detection is performed individually at each OFDM sub-carrier possibly inter…
Conventional sub-Nyquist sampling methods for analog signals exploit prior information about the spectral support. In this paper, we consider the challenging problem of blind sub-Nyquist sampling of multiband signals, whose unknown frequency support occupies only a small portion of a wide spectrum. Our primary design goals are efficient hardware implementation and low computational load on the supporting digital processing. We propose a system, named the modulated wideband converter, which first multiplies the analog signal by a bank of periodic waveforms. The product is then lowpass filtered …
In non-coherent wideband fading channels where energy rather than spectrum is the limiting resource, peaky and non-peaky signaling schemes have long been considered species apart, as the first approaches asymptotically the capacity of a wideband AWGN channel with the same average SNR, whereas the second reaches a peak rate at some finite critical bandwidth and then falls to zero as bandwidth grows to infinity. In this paper it is shown that this distinction is in fact an artifact of the limited attention paid in the past to the product between the bandwidth and the fraction of time it is in us…
This paper presents a power-efficient mask-constrained ultra-wideband (UWB) waveform design with radio channel effects taken into consideration. Based on a finite impulse response (FIR) filter, we develop a convex optimization model with respect to the autocorrelation of the filter coefficients to optimize the transmitted signal power spectrum, subject to a regulatory emission mask. To improve power efficiency, effects of transmitter radio frequency (RF) components are included in the optimization of the transmitter-output waveform, and radio propagation effects are considered for optimizing a…
The frequency selectivity of wireless communication channels can be characterized by the delay spread Ds of the channel impulse response. If the delay spread is small compared to the bandwidth W of the input signal, that is, Ds*W approximately equal to 1, the channel appears to be flat fading. For Ds*W >> 1, the channel appears to be frequency selective, which is usually the case for wideband signals. In the first case, small scale synchronization with a precision much higher than the sampling time T = 1/W is crucial. In this paper, it is shown by analytical means that this is different in the…
Compressive sensing (CS) exploits the sparsity present in many signals to reduce the number of measurements needed for digital acquisition. With this reduction would come, in theory, commensurate reductions in the size, weight, power consumption, and/or monetary cost of both signal sensors and any associated communication links. This paper examines the use of CS in the design of a wideband radio receiver in a noisy environment. We formulate the problem statement for such a receiver and establish a reasonable set of requirements that a receiver should meet to be practically useful. We then eval…
For systems and devices, such as cognitive radio and networks, that need to be aware of available frequency bands, spectrum sensing has an important role. A major challenge in this area is the requirement of a high sampling rate in the sensing of a wideband signal. In this paper a wideband spectrum sensing method is presented that utilizes a sub-Nyquist sampling scheme to bring substantial savings in terms of the sampling rate. The correlation matrix of a finite number of noisy samples is computed and used by a non-linear least square (NLLS) estimator to detect the occupied and vacant channels…
Indoor localization systems that are accurate and robust with respect to propagation channel conditions are still a technical challenge today. In particular, for systems based on range measurements from radio signals, non-line-of-sight (NLOS) situations can result in large position errors. In this paper, we address these issues using measurements in a representative indoor environment. Results show that conventional tracking schemes using high- and a low-complexity ranging algorithms are strongly impaired by NLOS conditions unless a very large signal bandwidth is used. Furthermore, we discuss …
M-ary On-Off Frequency-Shift-Keying (OOFSK) is a digital modulation format in which M-ary FSK signaling is overlaid on On/Off keying. This paper investigates the potential of this modulation format in the context of wideband fading channels. First it is assumed that the receiver uses energy detection for the reception of OOFSK signals. Capacity expressions are obtained for the cases in which the receiver has perfect and imperfect fading side information. Power efficiency is investigated when the transmitter is subject to a peak-to-average power ratio (PAR) limitation or a peak power limitation…
We propose a novel random triggering based modulated wideband compressive sampling (RT-MWCS) method to facilitate efficient realization of sub-Nyquist rate compressive sampling systems for sparse wideband signals. Under the assumption that the signal is repetitively (not necessarily periodically) triggered, RT-MWCS uses random modulation to obtain measurements of the signal at randomly chosen positions. It uses multiple measurement vector method to estimate the non-zero supports of the signal in the frequency domain. Then, the signal spectrum is solved using least square estimation. The distin…
In this paper, theoretical limits on time delay estimation are studied for ultra-wideband (UWB) cognitive radio systems. For a generic UWB spectrum with dispersed bands, the Cramer-Rao lower bound (CRLB) is derived for unknown channel coefficients and carrier-frequency offsets (CFOs). Then, the effects of unknown channel coefficients and CFOs are investigated for linearly and non-linearly modulated training signals by obtaining specific CRLB expressions. It is shown that for linear modulations with a constant envelope, the effects of the unknown parameters can be mitigated. Finally, numerical …
Too high sampling rate is the bottleneck to wideband spectrum sensing for cognitive radio (CR). As the survey shows that the sensed signal has a sparse representation in frequency domain in the mass, compressed sensing (CS) can be used to transfer the sampling burden to the digital signal processor. An analog to information converter (AIC) can randomly sample the received signal with sub-Nyquist rate to obtained the random measurements. Considering that the static frequency spectrum allocation of primary radios means the bounds between different primary radios is known in advance, here we inco…
Wideband spectrum sensing detects the unused spectrum holes for dynamic spectrum access (DSA). Too high sampling rate is the main problem. Compressive sensing (CS) can reconstruct sparse signal with much fewer randomized samples than Nyquist sampling with high probability. Since survey shows that the monitored signal is sparse in frequency domain, CS can deal with the sampling burden. Random samples can be obtained by the analog-to-information converter. Signal recovery can be formulated as an L0 norm minimization and a linear measurement fitting constraint. In DSA, the static spectrum allocat…
This paper studies the ergodic capacity of time- and frequency-selective multipath fading channels in the ultrawideband (UWB) regime when training signals are used for channel estimation at the receiver. Motivated by recent measurement results on UWB channels, we propose a model for sparse multipath channels. A key implication of sparsity is that the independent degrees of freedom (DoF) in the channel scale sub-linearly with the signal space dimension (product of signaling duration and bandwidth). Sparsity is captured by the number of resolvable paths in delay and Doppler. Our analysis is base…
We investigate the theory of affine groups in the context of designing radar waveforms that obey the desired wideband ambiguity function (WAF). The WAF is obtained by correlating the signal with its time-dilated, Doppler-shifted, and delayed replicas. We consider the WAF definition as a coefficient function of the unitary representation of the group $a\cdot x + b$. This is essentially an algebraic problem applied to the radar waveform design. Prior works on this subject largely analyzed narrow-band ambiguity functions. Here, we show that when the underlying wideband signal of interest is a pul…
In this paper, we propose a wideband Full Duplex (FD) Multiple-Input Multiple-Output (MIMO) communication system comprising of an FD MIMO node simultaneously communicating with two multi-antenna UpLink (UL) and DownLink (DL) nodes utilizing the same time and frequency resources. To suppress the strong Self-Interference (SI) signal due to simultaneous transmission and reception in FD MIMO systems, we propose a joint design of Analog and Digital (A/D) cancellation as well as transmit and receive beamforming capitalizing on baseband Orthogonal Frequency-Division Multiplexing (OFDM) signal modelin…
Sampling theories lie at the heart of signal processing devices and communication systems. To accommodate high operating rates while retaining low computational cost, efficient analog-to digital (ADC) converters must be developed. Many of limitations encountered in current converters are due to a traditional assumption that the sampling state needs to acquire the data at the Nyquist rate, corresponding to twice the signal bandwidth. In this thesis a method of sampling far below the Nyquist rate for sparse spectrum multiband signals is investigated. The method is called periodic non-uniform sam…
Dual-function radar-communication (DFRC) systems, which can efficiently utilize the congested spectrum and costly hardware resources by employing one common waveform for both sensing and communication (S&C), have attracted increasing attention. While the orthogonal frequency division multiplexing (OFDM) technique has been widely adopted to support high-quality communications, it also has great potentials of improving radar sensing performance and providing flexible S&C. In this paper, we propose to jointly design the dual-functional transmit signals occupying several subcarriers to realize mul…
The sparsity of multipaths in the wideband channel has motivated the use of compressed sensing for channel estimation. In this letter, we propose a different approach to sparse channel estimation. We exploit the fact that $L$ taps of channel impulse response in time domain constitute a non-orthogonal superposition of $L$ geometric sequences in frequency domain. This converts the channel estimation problem into the extraction of the parameters of geometric sequences. Numerical results show that the proposed scheme is superior to existing algorithms in high signal-to-noise ratio (SNR) and large …
Cognitive radio (CR) requires spectrum sensing over a broad frequency band. One of the crucial tasks in CR is to sample wideband signal at high sampling rate. In this paper, we propose an acquisition receiver with co-prime sampling technique for wideband sparse signals, which occupy a small part of band range. In this proposed acquisition receiver, we use two low speed analog-to-digital converters (ADCs) to capture a common sparse multiband signal, whose band locations are unknown. The two ADCs are synchronously clocked at co-prime sampling rates. The obtained samples are re-sequenced into a g…
In the wideband regime, the performance of many of the popular modulation schemes such as code division multiple access and orthogonal frequency division multiplexing falls quickly without channel state information. Obtaining the amount of channel information required for these techniques to work is costly and difficult, which suggests the need for schemes which can perform well without channel state information. In this work, we present one such scheme, called wideband time frequency coding, which achieves rates on the order of the additive white Gaussian noise capacity without requiring any …
In this paper, a channel estimator for wideband millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems with hybrid architectures and low-resolution analog-to-digital converters (ADCs) is proposed. To account for the propagation delay across the antenna array, which cannot be neglected in wideband mmWave massive MIMO systems, the discrete time channel that models the spatial wideband effect is developed. Also, the training signal design that addresses inter-frame, inter-user, and inter-symbol interferences is investigated when the spatial wideband effect is not negligibl…
Are Stacked Intelligent Metasurfaces (SIMs) Better than Single-layer Reconfigurable Intelligent Surfaces (RISs) for Wideband Multi-user MIMO Communication Systems?
The availability of positional information is of great importance in many commercial, public safety, and military applications. The coming years will see the emergence of location-aware networks with sub-meter accuracy, relying on accurate range measurements provided by wide bandwidth transmissions. In this two-part paper, we determine the fundamental limits of localization accuracy of wideband wireless networks in harsh multipath environments. We first develop a general framework to characterize the localization accuracy of a given node here and then extend our analysis to cooperative locatio…
In wideband millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems, channel estimation is challenging due to the hybrid analog-digital architecture, which compresses the received pilot signal and makes channel estimation a compressive sensing (CS) problem. However, existing high-performance CS algorithms usually suffer from high complexity. On the other hand, the beam squint effect caused by huge bandwidth and massive antennas will deteriorate estimation performance. In this paper, frequency-dependent angular dictionaries are first adopted to compensate for beam squint.…
