Lasing at telecommunication wavelengths from annular resonators employing radial Bragg reflectors is demonstrated at room temperature under pulsed optical pumping. Sub milliwatt pump threshold levels are observed for resonators with 0.5-1.5 wavelengths wide defects of radii 7-8 mm. The quality factors of the resonator modal fields are estimated to be on the order of a few thousands. The electromagnetic field is shown to be guided by the defect. Good agreement is found between the measured and calculated spectrum.
We propose and analyze a new type of a resonator in an annular geometry which is based on a single defect surrounded by radial Bragg reflectors on both sides. We show that the conditions for efficient mode confinement are different from those of the conventional Bragg waveguiding in a rectangular geometry. A simple and intuitive approach to the design of optimal radial Bragg reflectors is proposed and employed, yielding chirped gratings. Small bending radii and strong control over the resonator dispersion are possible by the Bragg confinement. A design compromise between large Free Spectral Ra…
A novel class of circular resonators, based on a radial defect surrounded by Bragg reflectors, is studied in detail. Simple rules for the design and analysis of such structures are derived using a transfer matrix formalism. Unlike conventional ring resonators, annular Bragg resonators (ABR) are not limited by the total internal reflection condition, and can exhibit both large free spectral ranges and low bend losses. The Bragg reflection mechanism enables the confinement of light within a defect consisting of a low refractive index medium (such as air). Strong atom-photon interaction can be ac…
We propose a new class of compact integrated optical circulators providing a large isolation level while maintaining a straightforward technological feasibility. Their layout is based on a nonreciprocal radial Bragg cavity composed of concentric magneto-optical rings. The circulator ports are standard rib waveguides, butt-coupled to the cavity by cutting through its outer rings. The device is specifically designed for operation in a uniform external magnetic field. Using a coupled-mode description of the complete cavity/waveguide-port system, we explore the rich behaviour of cavity circulators…
In this theoretical study, the author firstly discusses the wave interference of Bragg diffraction inside 3D crystal, followed by quantum mechanical interpretation on the diffraction process, and proves that the interference fringe between Bragg diffraction and the incident beam is identical to the lattice plane. By introducing the beam expander concept, we may explain the image projection mechanism of Bragg diffractions propagating through TEM: Transmission Electron Microscope. In practice, we will take projection images at zone axes, because of its symmetric high-density diffractions associa…
The reflectivity of various Bragg reflectors in connection to waveguide structures, including nanowires, has been investigated using modal reflection and transmission matrices. A semi-analytical model was applied yielding increased understanding of the diffraction effects present in such gratings. Planar waveguides and nanowire lasers are considered in particular. Two geometries are compared; Bragg reflectors within the waveguides are shown to have significant advantages compared to Bragg reflectors in the substrate, when diffraction effects are significant.
We report the fabrication and performance of the first C-band directly-written monolithic waveguide-laser. The waveguide-laser device was created in an Erbium and Ytterbium doped phosphate glass host and consisted of an optical waveguide that included a distributed feedback Bragg grating structure. The femtosecond laser direct-write technique was used to create both the waveguide and the waveguide-Bragg grating simultaneously and in a single processing step. The waveguide-laser was optically pumped at approximately 980 nm and lased at 1537nm with a bandwidth of less than 4 pm.
Femtosecond laser writing is applied to form Bragg grating waveguides in the diamond bulk. Type II waveguides are integrated with a single pulse point-by-point periodic laser modification positioned towards the edge of the waveguide core. These photonic devices, operating in the telecommunications band, allow for simultaneous optical waveguiding and narrowband reflection from a 4th order grating. This fabrication technology opens the way towards advanced 3D photonic networks in diamond for a range of applications.
We realize a fiber Bragg grating InGaN based laser diode emitting at 400 nm and demonstrate its high coherency. Thanks to the fabrication of a narrow band fiber Bragg grating in the near-UV, we can reach single-mode and single-frequency regimes for the self-injection locked diode. The device exhibits 44 dB side-mode-suppression-ratio and mW output power. Detailed frequency noise analysis reveals sub-MHz integrated linewidth and 16 kHz intrinsic linewidth. Such a narrow linewidth laser diode in the near-UV domain with a compact and low-cost design could find applications whenever coherency and …
We demonstrate a combination of optical and electronic feedback that significantly narrows the linewidth of distributed Bragg reflector lasers (DBRs). We use optical feedback from a long external fiber path to reduce the high-frequency noise of the laser. An electro-optic modulator placed inside the optical feedback path allows us to apply electronic feedback to the laser frequency with very large bandwidth, enabling robust and stable locking to a reference cavity that suppresses low-frequency components of laser noise. The combination of optical and electronic feedback allows us to significan…
A compact, strictly all-fiber, picosecond pulse source based on ytterbium (Yb) doped fiber is described. Stable solitary mode-locking is obtained in a fiber-oscillator utilizing a carefully designed chirped fiber-Bragg-grating (C-FBG) for both dispersion control and spectral filtering. Self-starting is assured through the use of a fiber-coupled semiconductor-saturable-absorber-mirror (SESAM). The oscillator's 50MHz 3.8ps pulse-train output at 1064nm wavelength is amplified to 1.2W average power by an Yb doped fiber-amplifier, yielding 6.45ps parabolic pulses. Numerical simulations of the fiber…
We demonstrate apodized fiber Bragg gratings inscribed with a point-by-point technique. We tailor the grating phase and coupling amplitude through precise control over the longitudinal and transverse position of each laser-inscribed modification. This method of apodization is facilitated by the highly-localized, high-contrast modifications generated by focussed IR femtosecond laser inscription. Our technique provides a simple method for the design and implementation of point-by-point fiber Bragg gratings with complex apodization profiles.
It is shown that the optical-electronic system consisted of the transmission Bragg grating, a laser and the intermediate sensitive to the vibrations mirror can detect the vibrations, when touched by them laser beam scan will exceed the angular divergence of the beam. The mathematical model of the sensor of the vibrations presented in the form of Taylor series describes the system response taking into account the operating point, in particular, describes the effect of the doubling of the modulation frequency response relative to the frequency of acting vibrations.
High-repetition-rate attosecond pulse sources are indispensable tools of time-resolved studies of electron dynamics, such as coincidence spectroscopy and experiments with high demands on statistics or signal-to-noise ratio, especially in case of solid and big molecule samples in chemistry and biology. Although with the high-repetition-rate lasers such attosecond pulses in a pump-probe configuration are possible to achieve, until now only a few such light sources have been demonstrated. Here, by shaping the driving laser to an annular beam, a 100-kHz attosecond pulse train (APT) is reported wit…
We report on the efficacy of a novel design for dielectric laser accelerators by adding a distributed Bragg reflector (DBR) to a dual pillar grating accelerating structure. This mimics a double-sided laser illumination, resulting in an enhanced longitudinal electric field while reducing the deflecting transverse effects, when compared to single-sided illumination. We improve the coupling efficiency of the incident electric field into the accelerating mode by 57 percent. The 12 $μ$m long structures accelerate sub-relativistic 28 keV electrons with gradients of up to 200 MeV/m in theory and 133 …
We investigate the spatial and spectral properties of broad-area vertical-cavity surface-emitting lasers (VCSEL) with frequency-selective feedback by a volume Bragg grating (VBG). We demonstrate wavelength locking similar to the case of edge-emitters but the spatial mode selection is different from the latter. On-axis spatial solitons obtained at threshold give way to off-axis extended lasing states beyond threshold. The investigations focus on a self-imaging external cavity. It is analyzed how deviations from the self-imaging condition affect the pattern formation and a certain robustness of …
We report the first experimental observation of photosensitivity in As2Se3 glass at a wavelength of 1550 nm. We utilize this photosensitivity to induce the first Bragg gratings using a laser source at a wavelength of 1550 nm. We quantify the photosensitivity thresholds related to exposition intensity and exposition time. Finally, we demonstrate that As2Se3 Bragg gratings are widely tunable in wavelength as the microwire can withstand an applied longitudinal strain of 4 \times 104 με.
Optimization of Lamb modes induced by laser can be achieved by adjusting the spatial source distribution to the mode wavelength ($λ$). The excitability of Zero-Group Velocity (ZGV) resonances in isotropic plates is investigated both theoretically and experimentally for axially symmetric sources. Optimal parameters and amplitude gains are derived analytically for spot and annular sources of either Gaussian or rectangular energy profiles. For a Gaussian spot source, the optimal radius is found to be $λ_{ZGV}/π$. Annular sources increase the amplitude by at least a factor of 3 compared to the opt…
The inscription of Bragg gratings in chalcogenide (As2Se3) wires with sub-wavelength diameter is proposed and demonstrated. A modified transverse holographic method employing He Ne laser light at a wavelength of λw = 633 nm allows the writing of Bragg grating reflectors in the 1550 nm band. The gratings reach an extinction ratio of 40 dB in transmission and a negative photo-induced index change of δn~0.01. The inscription of Bragg gratings in chalcogenide microwires will enable the fabrication of new devices with applications in nonlinear optics, and sensing in the near-to-mid-infrared region …
Solid state lasers are demanding independent control in the gain media and cavity loss to achieve ultra short laser pulses using passive mode-locking. Recently, laser mode-locking is achieved with a MBE structure with multiple quantum wells, designed to achieve two functions; Bragg mirror and changes in absorption to control the cavity dynamics. The use of an AlGaAs/AlAs Bragg mirror with a 15 nm GaAs saturable absorber used in a Cr:LiSAF tuneable laser proved to be effective to produce femtosecond pulses. The use of saturable absorbers thus far is a trial and error procedure that is changing …
Direct compression of femtosecond optical pulses from a Ti:sapphire laser oscillator was realized with a cholesteric liquid crystal acting as a nonlinear 1D periodic Bragg grating. With a 6-um thick sample, the pulse duration could be compressed from 100 to 48 femtoseconds. Coupled-mode equations for forward and backward waves were employed to simulate the dynamics therein and good agreement between theory and experiment was obtained.
Nonlinear frequency conversion is ubiquitous in laser engineering and quantum information technology. A long-standing goal in photonics is to integrate on-chip semiconductor laser sources with nonlinear optical components. Engineering waveguide lasers with spectra that phase-match to nonlinear processes on the same device is a formidable challenge. Here, we demonstrate difference-frequency generation in an AlGaAs Bragg reflection waveguide which incorporates the gain medium for the pump laser in its core. We include quantum dot layers in the AlGaAs waveguide that generate electrically driven l…
We demonstrate single-mode lasing at telecommunication wavelengths from a circular nanocavity employing a radial Bragg reflector. Ultra-small modal volume and Sub milliwatt pump threshold level are observed for lasers with InGaAsP quantum well active membrane. The electromagnetic field is shown to be tightly confined within the 300nm central pillar of the cavity. The quality factors of the resonator modal fields are estimated to be on the order of a few thousands.
Free-electron lasers (FELs) can now generate temporally short, high power x-ray pulses of unprecedented brightness, even though their longitudinal coherence is relatively poor. The longitudinal coherence can be potentially improved by employing narrow bandwidth x-ray crystal optics, in which case one must also understand how the crystal affects the field profile in time and space. We frame the dynamical theory of x-ray diffraction as a set of coupled waves in order to derive analytic expressions for the spatiotemporal response of Bragg scattering from temporally short incident pulses. We compu…
Chirped fiber Bragg gratings in Yb-doped fiber lasers allow tuning the net cavity dispersion, thus enabling access to pulse dynamics beyond the typical all-normal-dispersion dissipative soliton regime. This Letter demonstrates an ultrafast dispersion-managed all-polarization-maintaining fiber oscillator mode-locked with a nonlinear optical loop mirror. Using a chirped fiber Bragg grating inside the oscillator, it can work at net cavity dispersion in the range from -0.098 ps$^2$ up to +0.067 ps$^2$ and above at the wavelength of 1 $\mathrmμ$m. Depending on the configuration, the system can deli…
Thin film optical elements exhibiting translational invariance, and thus robustness to optical misalignment, are crucial for rapid development of compact and integrated optical devices. In this letter, we experimentally demonstrate a beam-shaping element that generates an annular beam by spatially filtering the fundamental Gaussian mode of a laser beam. The element comprises of a one-dimensional photonic crystal cavity fabricated using sputtered thin films. The planar architecture and in-plane symmetry of the element render our beam-shaping technique translationally invariant. The generated an…
A fiber Bragg grating (FBG) with an inverse-Gaussian apodization function is proposed and fabricated. It is shown that such a FBG possesses easily controllable dual-wavelength narrow transmission peaks. Incorporating such a FBG filter in a fiber laser with a linear cavity, stable dual-wavelength emission with 0.146 nm wavelength spacing is obtained. It provides a simple and low cost approach of achieving the dual-wavelength fiber laser operation.
Elastic scattering of laser radiation due to vacuum polarization by spatially modulated strong electromagnetic fields is considered. The Bragg interference arising at a specific impinging direction of the probe wave concentrates the scattered light in specular directions. The interference maxima are enhanced with respect to the usual vacuum polarization effect proportional to the square of the number of modulation periods within the interaction region. The Bragg scattering can be employed to detect the vacuum polarization effect in a setup of multiple crossed super-strong laser beams with para…
We present here a new type of cold atom interferometry gravimeter based on Bragg diffraction, which is able to increase the gravity measurement sensitivity and stability of common Raman atom gravimeters significantly. By comparing with Raman transition, the principles and advantages of Bragg diffraction-based atom gravimeters have been introduced. The theoretical model for a time-domain Bragg atom gravimeter with atomic incident direction parallels to the wave vector of Bragg lasers has been constructed. Some key technical requirements for an nth-order Bragg diffraction-based atom gravimeter h…
Control over spontaneous emission rate is important for improving efficiency in different semiconductor applications including lasers, LEDs and photovoltaics. Usually, an emitter should be placed inside the cavity to increase spontaneous emission rate, although it is technologically challenging. Here we experimentally demonstrate a phenomenon of super-radiance observed in a cavity-less periodic Bragg structure based on InAs monolayer-thick multiple quantum wells (MQW). The collective super-radiant mode shows enhanced emission rate for specific angles and frequencies. This behaviour correlates …
We discuss a phase-sensitive technique for remote interrogation of passive Bragg grating Fabry-Perot resonators. It is based on Pound-Drever-Hall laser frequency locking, using radio-frequency phase modulation sidebands to derive an error signal from the complex optical response, near resonance, of a Fabry-Perot interferometer. We examine how modulation frequency and resonance bandwidth affect this error signal. Experimental results are presented that demonstrate when the laser is locked, this method detects differential phase shifts in the optical carrier relative to its sidebands, due to min…
Laser light scattering systems with volume Bragg grating (VBG) filters, which act as a spectral/angular filter, have often been used as a point measurement technique with spatial resolution as low as a few hundred um defined by the beam waist. In this work, we demonstrate how VBG filters can be leveraged for spatially resolved measurements with several um resolution perpendicular to the laser propagation axis over a few mm along the beam propagation axis. The rejection ring, as determined by the angular acceptance criteria of the filter, is derived analytically, and the use of the ring for 1D …
A method for the agile generation of the optical frequencies required for laser cooling and atom interferometry of rubidium is demonstrated. It relies on fiber Bragg grating technology to filter the output of an electro-optic modulator and was demonstrated in a robust, alignment-free, single-seed, frequency-doubled, telecom fiber laser system. The system was capable of 50 ns frequency switching over a ~40 GHz range, ~0.5 W output power and amplitude modulation with a ~15 ns rise/fall time and an extinction ratio of 120 $\pm$ 2 dB. The technology is ideal for enabling high-bandwidth, mobile ind…
We present a comprehensive theoretical and experimental investigation of a dual-wavelength, bismuth-doped fiber (BDF) laser operating near 1700 nm based on cascaded cavities. The BDF provides optical gain from 1650 nm to 1800 nm when pumped at 1550 nm; the laser cavity is defined by a 90% mirror on one end and two fiber Bragg gratings (FBGs) separated by a length of BDF on the other. The laser can operate at either wavelength alone or both wavelengths simultaneously by simple adjustment of the pump power. Experimental results correlate well simulations based on a theoretical model of the laser…
We demonstrate femtosecond performance of an ultra-broadband high-index-contrast saturable Bragg reflector consisting of a silicon/silicon-dioxide/germanium structure that is fully compatible with CMOS processing. This device offers a reflectivity bandwidth of over 700 nm and sub-picosecond recovery time of the saturable loss. It is used to achieve mode-locking of an Er-Yb:glass laser centered at 1540 nm, generating 220 fs pulses, with the broadest output spectrum to date.
We report a versatile and cost-effective way of controlling the unsaturated loss, modulation depth and saturation fluence of graphene-based saturable absorbers (GSAs), by changing the thickness of a spacer between SLG and a high-reflection mirror. This allows us to modulate the electric field intensity enhancement at the GSA from 0 up to 400%, due to the interference of incident and reflected light at the mirror. The unsaturated loss of the SLG-mirror-assembly can be reduced to$\sim$0. We use this to mode-lock a VECSEL from 935 to 981nm. This approach can be applied to integrate SLG into vario…
In this paper, the transfer matrix method is used to investigate the reflectance properties in a symmetric defective annular photonic crystal (APC) containing semiconductor, high-$T_c$ superconductor and a radial defect layer. Numerical results offer many noteworthy features that can be very useful in designing optical devices. In this regard, the geometric effects of alternate layers on the optical reflectance of our defective APC structure by changing the thickness of different layers would be investigated. Then, the possibility of controlling the spectral position of existed photonic band g…
A new platform for fabricating polariton lasers operating at room temperature is introduced: nitride-based distributed Bragg reflectors epitaxially grown on patterned silicon substrates. The patterning allows for an enhanced strain relaxation thereby enabling to stack a large number of crack-free AlN/AlGaN pairs and achieve cavity quality factors of several thousands with a large spatial homogeneity. GaN and ZnO active regions are epitaxially grown thereon and the cavities are completed with top dielectric Bragg reflectors. The two structures display strong-coupling and polariton lasing at roo…
We propose and analyze a novel regenerative amplifier free electron laser (FEL) to produce fully coherent x-ray pulses. The method makes use of narrow-bandwidth Bragg crystals to form an x-ray feedback loop around a relatively short undulator. Self-amplified spontaneous emission (SASE) from the leading electron bunch in a bunch train is spectrally filtered by the Bragg reflectors and is brought back to the beginning of the undulator to interact repeatedly with subsequent bunches in the bunch train. The FEL interaction with these short bunches not only amplifies the radiation intensity but also…
The combination of grating-based frequency-selective optical feedback mechanisms, such as distributed feedback (DFB) or distributed Bragg reflector (DBR) structures, with quantum dot (QD) gain materials is a main approach towards ultra-high-performance semiconductor lasers for many key novel applications, either as stand-alone sources or as on-chip sources in photonic integrated circuits. However, the fabrication of conventional buried Bragg grating structures on GaAs, GaAs/Si, GaSb and other material platforms have been met with major material regrowth difficulties. We report a novel and univ…
We report a wavelength-tunable Q-switched mode-locked fiber laser based on a compact optical tuning device, which is fabricated by coating single-layer graphene on the surface of micro-fiber Bragg grating (MFBG). Based on thermal-optical effect through evanescent interaction between graphene and MFBG, the center wavelength of MFBG can be accurately controlled by adjusting power of an external laser. By inserting the fabricated device into a compact fiber laser cavity mode-locked by single-wall carbon nanotubes, stable Q-switched mode-locked pulse is generated. Experimental results show that th…
The use of a non-one-dimensional distributed feedback, arising through Bragg diffraction in spatially periodic systems (natural and artificial (electromagnetic, photonic) crystals), forms the foundation for the development of volume free electron lasers (VFELs). The present review addresses the basic principles of VFEL theory and describes the promising potential of VFELs as the basis for the development of high-power microwave and optical sources.
Prior to the invention of holography or lasers, Bragg's X-ray microscope opened the door to optical computation in short-wavelength studies using spatially coherent visible light, including phase retrieval methods. This optical approach lost ground to semiconductor detection and digital computing in the 1960s. Since then, visible optics including spatial light modulators (SLMs), array detectors and femtosecond lasers have become widely available, routinely allowing versatile and computer-interfaced imposition of optical phase, molecular coherent control, and detection. Today, high brilliance X…
Thulium-doped fibers suitable for core-pumped single-frequency lasers were fabricated by the modified chemical vapor deposition (MCVD) method. Refractive index profile, doping profile and spectral absorption was measured. High doping concentration of thulium ions should be achieved to allow for high absorption of light at a pump wavelength while the thulium ions clustering should be avoided to prevent the cooperative upconversion and quenching processes. The fabricated fibers featured pump absorption up to 70dB/m at a pump wavelength of 1611nm. The single-frequency master oscillator with a res…
Comparative analysis of fiber Bragg grating filter losses inscribed by continuous wave UV and femtosecond-IR lasers for astrophotonics
Leibniz Institute for Astrophysics Potsdam（波茨坦阿斯特罗物理莱布尼茨研究所）；Friedrich Schiller University Jena（耶拿弗里德里希·席勒大学）；National Astronomical Research Institute of Thailand（泰国国家天文研究所）；University of Potsdam（波茨坦大学）；Technische Universität Berlin（柏林工业大学）
Entangled photon sources (EPS), the major building block for a variety of quantum communication protocols, are commonly developed by utilizing the spontaneous parametric down-conversion (SPDC) in $χ^{2}$ nonlinear bulk optical materials. While high nonlinearity and long interaction length have established the superiority of the periodically poled crystals for EPSs, the phase-matching condition of such crystals is very sensitive to the fluctuation of the crystal temperature and the laser wavelength. As a result, deploying such sources outside the laboratory, for example, satellite-based applica…
Fiber Bragg Gratings have been advantageously used to improve the chaotic properties of semiconductor lasers. Though these components are known to be highly sensitive to environmental conditions, feedback phase fluctuations are often neglected. In this work, we experimentally demonstrate that the small variations of the propagation time induced by a simple thermal tuning of the FBG is sufficient to induce significant changes of the laser behavior. We report periodic stability enhancements linked with phase variations and highlight that both phase variation and phase offsets play an important r…
