A photon detector for BNL experiment E949 is described. The detector consists of lead/scintillator ``sandwich'' of 25 layers of 5 mm thick scintillator BC404 and 24 layers of 2 mm lead absorber. Readout is implemented with 30-60 cm long WLS fibers (BCF99-29AA) glued into grooves in the BC404. Average yield was measured with cosmic rays to be about 43 p.e./MeV. Extruded plastic scintillation counters developed for sandwich detectors of photons for the KOPIO experiment are also described. For a 7 mm thick counter with 4.3 m long WLS fibers spaced at 7 mm a light yield of 18.7 p.e./MeV and time resolution of 0.71 ns were obtained. A prototype photon veto module consisting of 10 layers of 7 mm thick extruded plastic slabs interleaved with 1 mm lead sheets was tested.
Prototype scintilator+WLS strips with SiPM readout for large muon detection systems were tested in the muon beam of the Fermilab Test Beam Facility. Light yield of up to 137 photoelectrons per muon per strip has been observed, as well as time resolution of 330 ps and position resolution along the strip of 5.4 cm.
A scalable 16-ch thermal neutron detection system has been developed in the framework of the upgrade of a neutron diffractometer. The detector is based on ZnS:${}^6$LiF scintillator with embedded WLS fibers which are read out with SiPMs. In this paper, we present the 16-ch module, the dedicated readout electronics, a direct comparison between the performance of the diffractometer obtained with the current ${}^3$He detector and with the 16-ch detection module, and the channel-to-channel uniformity.
Results are presented on R&D efforts to design and build large size veto panels, optimized for underground low background experiments, in the most efficient and economical way using commercially available components. A variety of plastic scintillators, photomultiplier tubes, wavelength shifting fibers, and light reflector combinations were tested. Results of these studies and performance of a 2.2 meter long panel are presented.
A sandwich detector composed of scintillator and steel-covered lead layers was introduced in the fixed-target COMPASS experiment at CERN for vetoing events not completely covered by the two-stage magnetic spectrometer. Wavelength shifting fibres glued into grooves in the scintillator tiles serve for fast read-out. Minimum ionizing particles impinging on the $2 \textrm{m} \times 2 \textrm{m}$ detector outside of a central hole, sparing the spectrometer's entry, are detected with a probability of 98%. The response to charged particles and photons is modeled in detail in Monte Carlo calculations.…
This work presents the design and performance study of compact strips of plastic scintillator with WLS-fiber readout in a dimension of 0.1 * 0.02 * 2 m3, which evaluates as a candidate for cosmic-ray muon detector for JUNO-TAO. The strips coupling with 3-inch PMTs are measured and compared between the single-end and double-end readout options first, and the strip of double-end option coupling with SiPM is further measured and compared with the results of that with the PMTs. The performance of the strips determined by a detailed survey along their length with cosmic-ray muon after a detailed ch…
The T2K neutrino experiment at J-PARC uses a set of near detectors to measure the properties of an unoscillated neutrino beam and neutrino interaction cross-sections. One of the sub-detectors of the near-detector complex, the side muon range detector (SMRD), is described in the paper. The detector is designed to help measure the neutrino energy spectrum, to identify background and to calibrate the other detectors. The active elements of the SMRD consist of 0.7 cm thick extruded scintillator slabs inserted into air gaps of the UA1 magnet yokes. The readout of each scintillator slab is provided …
Long lead-scintillator sandwich modules developed for the BNL experiment KOPIO are described. The individual 4 m long module consists of 15 layers of 7 mm thick extruded scintillator and 15 layers of 1 mm lead absorber. Readout is implemented via WLS fibers glued into grooves in a scintillator with 7 mm spacing and viewed from both ends by the phototubes. Time resolution of 300 ps for cosmic MIPs was obtained. Light output stability monitored for 2 years shows no degradation beyond the measurement errors. A 4 m long C-bent sandwich module was also manufactured and tested.
Two single channel detection units for thermal neutron detection are investigated in a neutron beam. They consist of two ZnS/${}^6$LiF scintillating layers sandwiching an array of WLS fibers. The pattern of this units can be repeated laterally and vertically in order to build up a one dimensional position sensitive multi-channel detector with the needed sensitive surface and with the required neutron absorption probability. The originality of this work arises from the fact that the WLS fibers are read out with SiPMs instead of the traditionally used PMTs or MaPMTs. The signal processing system…
Prototype scintilator+WLS strips with SiPM readout for muon system at future colliders were tested for light yield, time resolution and position resolution. Depending on the configuration, light yield of up to 36 photoelectrons per muon per SiPM has been achieved, as well as time resolution of 0.5 ns and position resolution of ~7 cm.
Radiation damage in the plastic scintillator and/or readout WLS fibers in the HE endcap calorimeter 1.4<y<4 in the CMS experiment at LHC and SLHC will require remediation after 2018. We describe one alternative using the existing brass absorber in the Endcap calorimeter, to replace the plastic scintillator tiles with BaF2 tiles, or quartz tiles coated with thin(1-5 micron) films of radiation-hard pTerphenyl(pTP) or the fast phosphor ZnO:Ga. These tiles would be read-out by easily replaceable arrays of straight, parallel WLS fibers coupled to clear plastic-cladded quartz fibers of proven radiat…
The main goal of the T2K long-baseline neutrino experiment is the precise measurement of the parameters of neutrino oscillation and the search for CP-violation in the lepton sector. In 2017, the T2K collaboration launched the Near Detector Upgrade project. This upgrade aims to reduce the systematic errors of the oscillation parameters from 6-7% to 3-4%. In order to accomplish such goal, ND280 Upgrade proposes to implement new upstream trackers to improve the wide angle acceptance and low momentum threshold. One of the novel technologies introduced in ND280 Upgrade is super fine-grained (SuperF…
A successful operation of a new optical readout system (THGEM + WLS + MGPDs (multichannel array of multipixel avalanche Geiger photodiodes) in a two-phase liquid xenon detector was demonstrated.
High-performance interrogation of inductor-capacitor (LC) microsensor has been a long-standing challenge due to the limited size of the sensor. Parity-time (PT) symmetry, an intriguing concept originated from quantum physics, has been utilized to improve the spectral resolution and sensitivity of the conventional readout circuit, while the PT symmetry condition has to be satisfied. In this work, a sandwich-type wireless capacitance readout mechanism based on perturbed PT-symmetric electronic trimer without manual tuning of the reader circuit is proposed. Theoretical eigenvalue analysis by solv…
The results of a development of a scintillator counter with wavelength shifting (WLS) fibre and a multi-pixel Geiger-mode avalanche photodiode readout are presented. The photodiode has a metal-resistor-semiconductor layered structure and operates in the limited Geiger mode. The scintillator counter has been developed for the EMMA underground cosmic ray experiment.
The Tokai-to-Kamioka (T2K) experiment is a second generation long baseline neutrino oscillation experiment which aims at a sensitive search for the nu_e appearance. The main design features of the T2K near detectors located at 280 m from the target are presented. Scintillator counters developed for the T2K near detectors are described. Readout of the counters is provided via WLS fibers embedded into S-shape grooves in a scintillator and viewed from both ends by multi-pixel avalanche photodiodes operating in a limited Geiger mode. A desription, operational principles and the results of tests of…
The CALICE collaboration is presently constructing a test hadron calorimeter (HCAL) with 7620 scintillator tiles read out by novel photo-detectors - Silicon Photomultipliers (SiPMs). This prototype is the first device which uses SiPMs on a large scale. We present the design of the HCAL and report on measured properties of more than 10 thousand SiPMs. We discuss the SiPM efficiency, gain, cross-talk, and noise rate dependence on bias voltage and temperature, including the spread in these parameters. We analyze the reasons for SiPM rejection and present the results of the long term stability stu…
The modular hadron calorimeter with micro-pixel avalanche photodiodes readout for the NA61/SHINE experiment at the CERN SPS is presented. The calorimeter consists of 44 independent modules with lead-scintillator sandwich structure. The light from the scintillator tiles is captured by and transported with WLS-fibers embedded in scintillator grooves. The construction provides a longitudinal segmentation of the module in 10 sections with independent MAPD readout. MAPDs with pixel density of $~10^{4}$/mm$^2$ ensure good linearity of calorimeter response in a wide dynamical range. The performance o…
Detectors based on polystyrene scintillator strips with WLS fiber readout are widely used to register charged particles in many high-energy physics experiments. The fibers are placed into grooves or holes along the strip. The detection efficiency of these devices can be significantly increased by improving the optical contact between the scintillator and the fiber by adding an optical filler into the groove/hole. This work is devoted to the study of the light yield of a 5-m-long scintillator strip with a 1.2-mm-diameter Kuraray Y11(200)~MC WLS fiber inserted into the strip's co-extruded hole f…
The application of reach-through avalanche photodiodes (R'APD) as a photodetector for scintillator tiles has been investigated. The light collected by WLS fibers (0.84mm and 1mm diameter) embedded in the scintillator has been transmited to the 0.5mm2 active surface of APD by clear optical fibers and optical connectors. A low noise charge sensitive preamplifier (approximately 400 electrons equivalent noise charge) has been used to gain the photodiode signal. Various configurations of tile-fibre systems, suitable for CMS and LHCb experiments at LHC have been studied using cosmic muons and muon b…
In the work presented here we built and evaluated a single-channel neutron detection unit consisting of a ZnS:$^6$LiF scintillator with embedded WLS fibers readout by a SiPM. The unit has a sensitive volume of 2.4 x 2.8 x 50 mm$^3$; 12 WLS fibers of diameter 0.25 mm are uniformly distributed over this volume and are coupled to a 1 x 1 mm$^2$ active area SiPM. We report the following performance parameters: neutron detection efficiency $\sim 65\,$% at $1.2\,Å$, background count rate $< 10^{-3}$ Hz, gamma-sensitivity with $^{60}$Co source $< 10^{-6}$, dead time $\sim 20\,μ$s, multi-count ratio $…
Two different technologies are considered for the Beam Calorimeters of the ILC detector. Simulation studies of the performance have been done for a diamond-tungsten sandwich calorimeter and for a homogeneous heavy element crystal calorimeter with optical fiber readout. Studies of the stability and the linearity of a polycrystalline diamond were done for the diamond-tungsten option. For the heavy crystal option the light yield reduction due to the wavelength shifting fiber readout was studied.
An upgrade of the long baseline neutrino experiment T2K near detector ND280 is currently being developed with the goal to reduce systematic uncertainties in the prediction of number of events at the far detector Super-Kamiokande. The upgrade program includes the design and construction of a new highly granular fully active scintillator detector with 3D WLS fiber readout as a neutrino target. The detector of about $200\times 180\times 60~cm^3$ in size and a mass of $\sim$2.2~tons will be assembled from about $2\times10^6$ plastic scintillator cubes of $1\times1\times1~cm^3$. Each cube is read o…
The FCAL collaboration is preparing large scale prototypes of special calorimeters to be used in the very forward region at a future linear electron positron collider for a precise and fast luminosity measurement and beam-tuning. These calorimeters are designed as sensor-tungsten calorimeters with very thin sensor planes to keep the Moliere radius small and dedicated FE electronics to match the timing and dynamic range requirements. A partially instrumented prototype was investigated in the CERN PS T9 beam in 2014 and at the DESY-II Synchrotron in 2015. It was operated in a mixed particle beam…
Precision Light Yield and Crosstalk Characterization for the SuperFGD scintillator cubes
Lebedev Physical Institute of the Russian Academy of Sciences（俄罗斯科学院列别杰夫物理研究所）；Institute for Nuclear Research of RAS（俄罗斯科学院核问题研究所）；Moscow Institute of Physics and Technology（莫斯科物理技术学院）；B.P. Konstantinov Petersburg Nuclear Physics Institute（B.P.康斯坦丁诺夫圣彼得堡核物理研究所）；National Research Center Kurchatov Institute（库尔恰托夫国家研究中心）；National Research Nuclear University MEPhI（国立核研究大学MEPhI）
Detection of scintillation light in noble gases with wavelength-shifting optical fibers
Donostia International Physics Center, BERC Basque Excellence Research Centre（多诺西亚国际物理中心，BERC巴斯克卓越研究中心）；Ikerbasque (Basque Foundation for Science)（伊克拉巴斯克（巴斯克科学基金会））；Instituto de Física Corpuscular (IFIC), CSIC & Universitat de València（粒子物理研究所（IFIC），西班牙国家研究委员会与瓦伦西亚大学）；Department of Physics, Universidad del Pais Vasco (UPV/EHU)（巴斯克国立大学（UPV/EHU）物理系）；Nuclear Research Center Negev（内盖夫核研究中心）
The SoLid experiment aims to measure neutrino oscillation at a baseline of 6.4 m from the BR2 nuclear reactor in Belgium. Anti-neutrinos interact via inverse beta decay (IBD), resulting in a positron and neutron signal that are correlated in time and space. The detector operates in a surface building, with modest shielding, and relies on extremely efficient online rejection of backgrounds in order to identify these interactions. A novel detector design has been developed using 12800 5 cm cubes for high segmentation. Each cube is formed of a sandwich of two scintillators, PVT and 6LiF:ZnS(Ag), …
The possibility to build a SiPM-readout muon detector (SiRO), using plastic scintillators with optical fibers as sensitive volume and readout by SiPM photo-diodes, is investigated. SiRO shall be used for tracking cosmic muons based on amplitude discrimination. The detector concept foresees a stack of 6 active layers, grouped in 3 sandwiches for determining the muon trajectories through 3 planes. After investigating the characteristics of the photodiodes, tests have been performed using two detection modules, each being composed from a plastic scintillator sheet, $100 \times 25 \times 1\,$cm$^{…
Gas Electron Multipliers (GEMs) can be produced in large foils and molded in different shapes. The possibility to create cylindrical layers has opened the opportunity to use such detector as internal tracker at collider experiments. One crucial item is to have low material budget in the active area, so the supporting structure of anode and cathode must be light. KLOE2 collaboration has built the first Cylindrical GEM detector with honeycomb material with carbon fiber skins produced at high temperature. BESIII is developing an innovative CGEM detector with charge and time readout. Among several…
