At the Accelerator Test Facility (ATF) at KEK intrabeam scattering (IBS) is a strong effect for an electron machine. It is an effect that couples all dimensions of the beam, and in April 2000, over a short period of time, all dimensions were measured as functions of current. In this report we derive a simple relation for the growth rates of emittances due to IBS. We apply the theories of Bjorken-Mtingwa, Piwinski, and a formula due to Raubenheimer to the ATF parameters, and find that the results all agree (if in Piwinski's formalism we replace the dispersion squared over beta by the dispersion invariant). Finally, we compare theory, including the effect of potential well bunch lengthening, with the April 2000 measurements, and find reasonably good agreement in the energy spread and horizontal emittance dependence on current. The vertical emittance measurement, however, implies that either: there is error in the measurement (equivalent to an introduction of 0.6% x-y coupling error), or the effect of intrabeam scattering is stronger than predicted (35% stronger in growth rates).
In April 2000 the single bunch energy spread, bunch length, horizontal emittance, and vertical emittance were measured as functions of current in KEK's ATF damping ring. In this report the measurement results are analyzed in light of intrabeam scattering theory. The measurements are found to be relatively consistent with theory, although the measured effects appear to be stronger than theory. In addition, the factor of 3 growth in vertical emittance at a current of 3 mA does not seem to be supported.
We derive a simple relation for estimating the relative emittance growth in x and y due to intrabeam scattering (IBS) in electron storage rings. We show that IBS calculations for the ATF damping ring, when using the formalism of Bjorken-Mtingwa, a modified formalism of Piwinski (where eta squared divided by beta has been replaced by the dispersion invariant), or a simple high-energy approximate formula all give results that agree well. Comparing theory, including the effect of potential well bunch lengthening, with a complete set of ATF steady-state beam size vs. current measurements we find r…
The proposed High-Energy LHC project presents an unusual combination of strong synchrotron radiation (SR) damping and intrabeam scattering (IBS), which is not seen in present-day hadron colliders. The subject of investigation reported in this paper was the simulation of beam-beam effect for the HE-LHC parameters. Parameters of SR and IBS are calculated, and the luminosity evolution is simulated in the absence of beambeam interaction. Then, a weak-strong numerical simulation is used to predict the effect of beam-beam interaction on particle losses and emittance evolution.
This note finds results for the intrabeam scattering growth rates for a bi-gaussian distribution. The bi-gaussian distribution is interesting for studying the possibility of using electron cooling in RHIC. Experiments and computer studies indicate that in the presence of electron cooling, the beam distribution changes so that it developes a strong core and a long tail which is not described well by a gaussian, but may be better described by a bi-gaussian. Being able to compute the effects of intrabeam scattering for a bi-gaussian distribution would be useful in computing the effects of electro…
Intrabeam scattering studies with large-emittance-ratio ion beams in the Relativistic Heavy Ion Collider, and implications for the Electron-Ion Collider
In order to study the background status in the ATF2 beam line and the interaction point (IP), this paper developed an analytical method to give the estimation of ATF beam halo distribution based on K. Hirata and K. Yokoya's theory. The equilibrium particle distribution of beam tail in ATF damping ring, when each electron is being affected by, in addition to the synchrotron radiation damping effects, several stochastic processes, such as beam-gas scattring, beam-gas bremsstrahlung and intra-beam scattering, was presented. This method is common and can be applied on other electron rings.
Halo distribution is a key topic for background study. This paper has developed an analytical method to give an estimation of ATF beam halo distribution. The equilibrium particle distribution of the beam tail in the ATF damping ring is calculated analytically with different emittance and different vacuum degree. The analytical results agree the measurements very well. This is a general method which can be applied to any electron rings.
Electron cooling that results when a bunch of electrons overlaps a bunch of ions , with both bunches moving at the same velocity, may be considered to be an intrabeam scattering process. The process is similar to the usual intrabeam scattering, where the ions scatter from each other and usually results in beam growth. An important difference is that in electron cooling the mass of the ion is different from and much larger than the mass of the electron. This difference considerably complicates the intrabeam scattering theory. It introduces a new term in the emittance growth rate, which vanishes…
Beginning with the general Bjorken-Mtingwa solution for intrabeam scattering (IBS) we derive an accurate, greatly simplified model of IBS, valid for high energy beams in normal storage ring lattices. In addition, we show that, under the same conditions, a modified version of Piwinski's IBS formulation (where dispersion squared over beta has been replaced by the dispersion invariant) asymptotically approaches the result of Bjorken-Mtingwa.
Beginning with the general Bjorken-Mtingwa solution, we derive a simplified model of intrabeam scattering (IBS), one valid for high energy beams in normal storage rings; our result is similar, though more accurate than a model due to Raubenheimer. In addition, we show that a modified version of Piwinski's IBS formulation (where eta squared over beta has been replaced by the dispersion invariant) at high energies asymptotically approaches the same result.
The wire scanners are used for a measurement of the very small beam size and the emittance in Accelerator Test Facility (ATF). They are installed in the extraction beam line of ATF damping ring. The extracted beam emittance are ex=1.3x10-9 m.rad, ey=1.7x10-11 m.rad with 2x109 electrons/bunch intensity and 1.3GeV energy. The wire scanners scan the beam by a tungsten wire with beam repetition 0.78Hz. The scanning speed is, however, very slow(~500um/sec). Since the extracted beam is quite stable by using the double kicker system, precision of the size measurement is less than 2um for 50 - 150um h…
In circular colliders, as well as in damping rings and synchrotron radiation light sources, beam halo is one of the critical issues limiting the performance as well as potentially causing component damage and activation. It is imperative to clearly understand the mechanisms that lead to halo formation and to test the available theoretical models. Elastic beam-gas scattering can drive particles to large oscillation amplitudes and be a potential source of beam halo. In this paper, numerical estimation and Monte Carlo simulations of this process at the ATF of KEK are presented. Experimental measu…
Intrabeam scattering (IBS) limits the emittance and single-bunch current that can be achieved in electron or positron storage ring colliders, damping rings, and light sources. Much theoretical work on IBS exists, and while the theories have been validated in hadron and ion machines, the presence of strong damping makes IBS in lepton machines a different phenomenon. We present the results of measurements at CesrTA of IBS dominated beams, and compare the data with theory. The beams we study have parameters typical of those specified for the next generation of wiggler dominated storage rings: low…
This report presents bunch length and energy spread measurements performed in April 2000 at the ATF Damping Ring, at KEK. Measurements were performed with the beam on and then off the linear (difference) coupling resonance. Due to strong intra-beam scattering in the ATF ring, the results depended strongly on the coupling.
Compton scattering provides one of the most promising scheme to obtain polarized positrons for the next generation of $e^-$ -- $e^+$ colliders. Moreover it is an attractive method to produce monochromatic high energy polarized gammas for nuclear applications and X-rays for compact light sources. In this framework a four-mirror Fabry-Pérot cavity has been installed at the Accelerator Test Facility (ATF - KEK, Tsukuba, Japan) and is used to produce an intense flux of polarized gamma rays by Compton scattering \cite{ipac-mightylaser}. For electrons at the ATF energy (1.28 GeV) Compton scattering …
Interplay of space charge and intrabeam scattering in the LHC ion injector chain
European Organization for Nuclear Research (CERN)（欧洲核子研究组织（CERN））；University of Crete（克里特大学）；Instituto Galego de Física de Altas Enerxías (IGFAE), Universidade de Santiago de Compostela（圣地亚哥-德孔波斯特拉大学加利西亚高能物理研究所）
The motivation for the treatment of intrabeam scattering theory given in this paper was to find results which would be convenient for computing the intrabeam scattering growth rates for particle distributions which are more complicated than a simple gaussian. It was shown by A. Piwinski that beam growth rates due to intrabeam scattering can be expressed as a multidimensional integral [1]. It was pointed out by J. Bjorken and S. Mtingwa [2] that the reduction of the multidimensional integral to a 3-dimensional untegral is made easier by writing the integral so that its relativistic transformati…
This paper presents the pre-experiment plan and prediction of the first stage of Vacuum Laser Acceleration (VLA) collaborating by UCLA, Fudan University and ATF-BNL. This first stage experiment is a Proof-of-Principle to support our previously posted novel VLA theory. Simulations show that based on ATF's current experimental conditions, the electron beam with initial energy of 15MeV can get net energy gain from intense CO2 laser beam. The difference of electron beam energy spread is observable by ATF beam line diagnostics system. Further this energy spread expansion effect increases along with…
A beam position monitor (BPM) upgrade at the KEK Accelerator Test Facility (ATF) damping ring has been accomplished, carried out by a KEK/FNAL/SLAC collaboration under the umbrella of the global ILC R&D effort. The upgrade consists of a high resolution, high reproducibility read-out system, based on analog and processing, and also implements a new automatic gain error correction schema. The technical concept and realization as well as results of beam studies are presented.
We present energy spread and bunch length measurements at the Accelerator Test Facility (ATF) at KEK, as functions of current, for different ring rf voltages, and with the beam both on and off the coupling resonance. We fit the on-coupling bunch shapes to those of an impedance model consisting of a resistor and an inductor connected in series. We find that the fits are reasonably good, but that the resulting impedance is unexpectedly large.
The investigation of beam halo transverse distributions is important for the understanding of beam losses and the control of backgrounds in Future Linear Colliders (FLC). A novel in vacuum diamond sensor (DSv) scanner with four strips has been designed and developed for the investigation of the beam halo transverse distributions and also for the diagnostics of Compton recoil electrons after the interaction point (IP) of ATF2, a low energy (1.3 GeV) prototype of the final focus system for the ILC and CLIC linear collider projects. Using the DSv, a dynamic range of $\sim10^6$ has been successful…
KEK-ATF is studying the low-emittance multi-bunch electron beam for the future linear collider. In ATF, thermionic gun is used to generate 20 bunches electron beam with the bunch spacing of 2.8 ns. Due to a distortion of the gun emission and the beam loading effect in the bunching system, the intensity for each bunch is not uniform by up to 40 % at the end of the injector. We have developed a system to correct the gun emission by precisely controlling the cathode voltage with a function generator. For the beam loading effect, we have introduced RF amplitude modulation on Sub Harmonic Buncher, …
The beam test for the Shintake monitor succeeded in measuring signal modulation with the laser interference fringe pattern in November 2009. We have studied the error sources, and evaluated the systematic error to be less than 30% for 1 minute measurements. This paper centers on the evaluation of the Shintake monitor performance through analyzing beam tests deta. Most systematic error sources are well understood, enabling accurate measurement of the beam size when it reaches 37 nm.
As part of the R\&D for the 50 MeV ThomX Compton source project, we have studied the effect of several beam dynamics processes on the evolution of the beam in the ring. The processes studied include among others Compton scattering, intrabeam scattering, coherent synchrotron radiation. We have performed extensive simulations of a full injection/extraction cycle (400000 turns). We show how each of these processes degrades the flux of photons produced and how a feedback system contributes to recovering most of the flux.
KEK-ATF is doing R&D establishing high-current and low-emittance electron beam for the future linear colliders. In ATF, 15 ps length electron beam is generated by combination of a thermionic gun, a couple of 357 MHz SHBs, and a S-band TW buncher. In the linac, beam instability caused by the fluctuated amplitude and phase of SHBs has been observed. The reason of the fluctuation is considered to be the multi-pacting in the SHB cavity. In addition, Q value of the cavity is almost half of the designed value, then SHBs are not operated in an optimum condition. We have fabricated new SHBs with consi…
The use of coherent transition radiation autocorrelation methods to determine bunch length and profile information is examined with the compressed electron beam at the BNL ATF. A bi-gaussian fit is applied to coherent transition radiation auto-correlation data to extract the longitudinal current distribution. The effects of large transverse beam sizes are studied in theory and compared to experimental results. A suitable form of the correction factor is derived for beams with large transverse-longitudinal aspect ratios.
Damping Ring Optimization in Natural Emittance and IBS Dominated Regimes
Cornell Laboratory for Accelerator Based Sciences and Education (CLASSE), Cornell University（康奈尔大学加速器科学与工程实验室）；SLAC National Accelerator Laboratory（斯坦福直线加速器中心）；Cornell High Energy Synchrotron Source (CHESS), Cornell University（康奈尔大学高能同步辐射光源）
We discuss the approach of generating round beams for ultimate storage rings using vertical damping wigglers (with horizontal magnetic field). The vertical damping wigglers provide damping and excite vertical emittance. This eliminates the need to generate large linear coupling that is impractical with traditional off-axis injection. We use a PEP-X compatible lattice to demonstrate the approach. This lattice uses separate quadrupole and sextupole magnets with realistic gradient strengths. Intrabeam scattering effects are calculated. The horizontal and vertical emittances are 22.3 pm and 10.3 p…
At the Large Hadron Collider (LHC), the interplay between a series of effects, including intrabeam scattering (IBS), synchrotron radiation, longitudinal beam manipulations, two beam effects (beam-beam, e-cloud) and machine non-linearities, can change the population of the core and tails and lead to non-Gaussian beam distributions, at different periods during the beam cycle. By employing generalised distribution functions, it can be demonstrated that the modified non-Gaussian beam profiles have an impact in the beam emittance evolution by itself and thereby to the collider luminosity. This pape…
In storage rings, horizontal dispersion in the rf cavities introduces horizontal-longitudinal (xz) coupling, contributing to beam tilt in the xz plane. This coupling can be characterized by a "crabbing" dispersion term ζa that appears in the normal mode decomposition of the 1-turn transfer matrix. ζa is proportional to the rf cavity voltage and the horizontal dispersion in the cavity. We report experiments at the Cornell Electron Storage Ring Test Accelerator (CesrTA) where xz coupling was explored using three lattices with distinct crabbing properties. We characterize the xz coupling for each…
A method for producing narrow-band THz radiation proposes passing an ultra-relativistic beam through a metallic pipe with small periodic corrugations. We present results of a measurement of such an arrangement at Brookhaven's Accelerator Test Facility (ATF). Our pipe was copper and was 5 cm long; the aperture was cylindrically symmetric, with a 1 mm (radius) bore and a corrugation depth (peak-to-peak) of 60 um. In the experiment we measured both the effect on the beam of the structure wakefield and the spectral properties of the radiation excited by the beam. We began by injecting a relatively…
As part of the positron source R&D for future $e^+-e^-$ colliders and Compton based compact light sources, a high finesse non-planar four-mirror Fabry-Perot cavity has recently been installed at the ATF (KEK, Tsukuba, Japan). The first measurements of the gamma ray flux produced with a such cavity using a pulsed laser is presented here. We demonstrate the production of a flux of 2.7 $\pm$ 0.2 gamma rays per bunch crossing ($\sim3\times10^6$ gammas per second) during the commissioning.
A high-precision intra-bunch-train beam orbit feedback correction system has been developed and tested in the ATF2 beamline of the Accelerator Test Facility at the High Energy Accelerator Research Organization in Japan. The system uses the vertical position of the bunch measured at two beam position monitors (BPMs) to calculate a pair of kicks which are applied to the next bunch using two upstream kickers, thereby correcting both the vertical position and trajectory angle. Using trains of two electron bunches separated in time by 187.6~ns, the system was optimised so as to stabilize the beam o…
A method for producing narrow-band THz radiation proposes passing an ultra-relativistic beam through a metallic pipe with small periodic corrugations. We present results of a measurement of such an arrangement at Brookhaven's Accelerator Test Facility (ATF). Our pipe was copper and was 5 cm long; the aperture was cylindrically symmetric, with a 1 mm (radius) bore and a corrugation depth (peak-to-peak) of 60 um. In the experiment we measured both the effect on the beam of the structure wakefield and the spectral properties of the radiation excited by the beam. We began by injecting a relatively…
Optical transition radiation interferometry (OTRI) has been shown to be a very useful technique to measure the divergence of electron beams with energies in the range of 15-100 MeV. However, application of this method to low energy or very high quality beams is limited by scattering in the front foil of the interferometer. To overcome this limitation we propose to use a perforated front foil. For the beam energy and hole sizes we are considering, the unscattered beam electrons passing through the holes will produce diffraction radiation (ODR). The total radiation produced from the first and se…
A laserwire transverse electron beam size measurement system has been developed and operated at the Accelerator Test Facility 2 (ATF2) at KEK. Special electron beam optics were developed to create an approximately 1 x 100 μm (vertical x horizontal) electron beam at the laserwire location, which was profiled using a 150 mJ, 71 ps laser pulse with a wavelength of 532 nm. The precise characterisation of the laser propagation allows the non-Gaussian transverse profiles of the electron beam caused by the laser divergence to be deconvolved. A minimum vertical electron beam size of 1.07 ${\pm}$ 0.06 …
With electron beam durations down to femtoseconds and sub-femtoseconds achievable in current state-of-the-art accelerators, longitudinal bunch length diagnostics with resolution at the attosecond level are required. In this paper, we present such a novel measurement device which combines a high power laser modulator with an RF deflecting cavity in the orthogonal direction. While the laser applies a strong correlated angular modulation to a beam, the RF deflector ensures the full resolution of this streaking effect across the bunch hence recovering the temporal beam profile with sub-femtosecond…
