arXivDaily arXiv每日学术速递 周一至周五更新
arXiv 2407.11210physics.flu-dyn
收藏

先进涡轮叶栅的风洞试验及建模启示

Wind Tunnel Testing and Modeling Implications of an Advanced Turbine Cascade

Sharath Sathish

AI总结:

本文针对低亚声速等截面涡轮叶片开展大规模风洞试验,测定多参数下的气动性能,结合三维测量补充结果,验证了设计目标,并评估了CFX和MISES两种CFD工具的预测能力,讨论了测量与预测的差异。

摘要:

本文介绍了针对低亚声速应用开发的等截面涡轮叶片开展的大规模风洞(WT)平面叶栅试验研究。试验设计了 comprehensive 实验方案,旨在测定该叶片在多种几何参数(如节弦比、安装角)和气动力参数(如雷诺粗糙度、马赫数、攻角)变化条件下的气动性能。除了经典的二维(2D)测量外,还开展了针对性的三维(3D)测量以补充二维结果,从而得出关于所研究叶片三维流动特性的更多结论。本次试验主要覆盖转捩流动区和全湍流流动起始区(最大雷诺数为250万)。对试验结果进行后处理,以分析和评估关键气动特性;涉及的参数包括叶型截面载荷分布、损失系数和气流偏转角。除验证设计目标外,本次风洞试验的另一并行目标是更准确地评估所使用的CFD工具(CFX和MISES)在风洞产生的基本流动条件下的预测能力,旨在全面了解在考虑上述设计和运行变量的情况下,所用设计工具所能达到的吻合程度。测量结果明确表明,设计成功实现了预设目标。本文还详细讨论了在几何设计、气动设计以及非设计工况下,关键参数的测量值与预测值之间存在的差异。

英文摘要:

This paper describes the extensive Wind Tunnel (WT) linear cascade testing campaign carried out on a constant section turbine blade developed for low subsonic applications. Comprehensive experimental program was designed to determine the aerodynamic behaviour of this blade under a wide range of varying geometrical like Pitch to Chord Ratio, Stagger Angle and Aerodynamic like Reynolds Roughness, Mach number, Incidence angle conditions. In addition to the classical Two-Dimensional (2D) measurements, targeted Three-Dimensional (3D) surveys have been performed to complement the 2D results, allowing to draw supplementary conclusions as to the behaviour of the considered blade in three-dimensions. The performed experiments predominantly covered the transitional and beginning of a fully turbulent flow regime (maximum Re is 2.5 million). Post processing of experimental results were done in view of exploitation and judgment of some key aerodynamic aspects; parameters such as profile section load distribution, loss coefficient and flow deviation angle. Alongside with confirmation of the design targets, a parallel goal pursued in the current WT testing, was to get a more accurate idea as to the predictive capabilities of the employed CFD tools (CFX and MISES) under the basic flow condition generated in the WT. The aim was to get a global picture, as to the level of agreement that can be reached by the used design tools while accounting for the afore-mentioned design, operational variables. The obtained measurement results clearly indicated the success of the design in achieving the pre-set targets. The paper further provides a detailed discussion on the identified discrepancies, measurement versus predictions, of the key parameters at the geometric, aerodynamic design as well as off-design conditions.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑