A subspace of resonant magnetic perturbation (RMP) configurations for edge localized mode (ELM) suppression is predicted for H-mode burning plasmas at 15 MA current and 5.3 T magnetic field in ITER. Perturbation of the core plasma can be reduced by a factor of 2 for equivalent edge stability proxies, while the perturbed plasma boundary geometry remains mostly resilient. The striation width of perturbed field lines connecting from the main plasma (normalized poloidal flux $< 1$) to the divertor targets is found to be significantly larger than the expected heat load width in the absence of RMPs. This facilitates heat load spreading with peak values at an acceptable level below 10 MW m${}^{-2}$ on the outer target already at moderate gas fueling and low Ne seeding for additional radiative dissipation of the 100 MW of power into the scrape-off layer (SOL). On the inner target, however, re-attachment is predicted away from the equilibrium strike point due to increased upstream heat flux, higher downstream temperature and less efficient impurity radiation.
General formula describing both the divertor strike point splitting and width of magnetic islands created by resonant magnetic perturbations (RMPs) in a poloidally diverted tokamak equilibrium is derived. Under the assumption that the RMP is produced by coils at the low-field side such as those used to control edge localized modes (ELMs) it is demonstrated that the width of islands on different magnetic surfaces at the edge and the amount of divertor splitting are related to each other. Explanation is provided of aligned maxima of the perturbation spectra with the safety factor profile - an ef…
Self-consistent simulations of neoclassical and electrostatic turbulent transport in a DIII-D H-mode edge plasma under resonant magnetic perturbations (RMPs) have been performed using the global total-f gyrokinetic particle-in-cell code XGC, in order to study density-pump out and electron heat confinement. The RMP field is imported from the extended magneto-hydrodynamics (MHD) code M3D-C1, taking into account the linear two-fluid plasma response. With both neoclassical and turbulence physics considered together, the XGC simulation reproduces two key features of experimentally observed edge tra…
Edge localised modes (ELMs) are a concern for future devices as they can limit the operational lifetime of the divertor. The mitigation of ELMs can be performed by the application of resonant magnetic perturbations (RMPs) which act to degrade the pressure gradient in the edge of the plasma. Investigations of the effect of RMPs on MAST have been performed in a range of plasmas using perturbations with toroidal mode numbers of n=3, 4 and 6. It has been seen that the RMPs increase the ELM frequency, which gives rise to a corresponding decrease in the ELM energy. The reduced ELM energy decreases t…
Resonant magnetic perturbations (RMPs) can mitigate the edge-localized modes (ELMs), i.e. cause a change of the ELM character towards smaller energy loss and higher frequency. During mitigation a change of the spatial structure of ELM loads on divertor was observed on DIII-D and MAST: the power is deposited predominantly in the footprint structures formed by the magnetic perturbation. In the present contribution we develop a theory explaining this effect, based on the idea that part of the ELM loss is caused by parallel transport in the homoclinic tangle formed by the magnetic perturbation of …
The application of resonant magnetic perturbations (RMPs) produces splitting of the divertor strike point due to the interaction of the RMP field and the plasma field. The application of a rotating RMP field causes the strike point splitting to rotate, distributing the particle and heat flux evenly over the divertor. The RMP coils in MAST have been used to generate a rotating perturbation with a toroidal mode number n=3. The ELM frequency is doubled with the application of the RMP rotating field, whilst maintaining the H mode. During mitigation, the ELM peak heat flux is seen to be reduced by …
Divertor strike point splitting induced by resonant magnetic perturbations (RMPs) has been observed on MAST for a variety of RMP configurations in a plasma scenario with Ip=750kA where those configurations all have similar resonant components. Complementary measurements have been obtained with divertor Langmuir probes and an infrared camera. Clear splitting consistently appears in this scenario only in the even configuration of the perturbation coils, similarly to the density pump-out. These results present a challenge for models of plasma response to RMPs.
Edge localised modes (ELMs) are a concern for future devices, such as ITER, due to the large transient heat loads they generate on the divertor surfaces which could limit the operational time of the device. This paper discusses the application of resonant magnetic perturbations (RMPs) as a mechanism for ELM control on MAST. Experiments have been performed using an n=3 toroidal mode number perturbation and measurements of the strike point splitting performed. The measurements have been made using both infrared and visible imaging to measure the heat and particle flux to the divertor. The measur…
We present that a statistical method known as the Complexity-Entropy analysis is useful to characterize a state of plasma turbulence and flux in the resonant magnetic perturbation (RMP) edge localized mode (ELM) control experiment. The RMP ELM suppression phase with the stochastic pedestal top temperature fluctuation can be distinguished from the natural ELM free phase with the chaotic fluctuation. It is discussed that the stochastic temperature fluctuation localized near the pedestal top can be originated from the narrow layer of the field penetration near the pedestal top. The forced magneti…
It is found that the X-Divertor (XD) configuration [1-3] can be made with the conventional PF coil set on ITER[4], where all PF coils are outside the TF coils. Desirable configurations are possible where the PF currents are below the present maximum design limits on ITER, and where the baseline divertor cassette is used. It is possible that the XD could be used to assist in high-power operation on ITER, but some further issues need examination. Note that the increased major radius of the Super X-Divertor (SXD) [5-8] is not a feature of the XD geometry. In addition, we present an XD configurati…
The XGC1 edge gyrokinetic code is used for a high fidelity prediction for the width of the heat-flux to divertor plates in attached plasma condition. The simulation results are validated against the empirical scaling $λ_q \propto B_P^{-γ}$ obtained from present tokamak devices, where $λ_q$ is the divertor heat-flux width mapped to the outboard midplane and $γ_q=1.19$ as defined by T. Eich et al. [Nucl. Fusion 53 (2013) 093031], and $B_P$ is the magnitude of the poloidal magnetic field at outboard midplane separatrix surface. This empirical scaling predicts $λ_q \leq 1mm$ when extrapolated to I…
Investigations of parametric scaling of power exhaust in the alternative divertor configuration (ADC) SOLPS-ITER simulation database of the EU-DEMO are conducted and compared to predictions based on the Lengyel model. The Lengyel model overpredicts the necessary argon concentrations for LFS divertor detachment by about a factor of 5-10 relative to the SOLPS-ITER simulations. Therefore, while the Lengyel model predicts that plasmas with accetable divertor heat loads in EU-DEMO would exceed the tolerable upstream impurity concentrations by a large margin, there are several SOLPS-ITER solutions w…
Understanding and predicting divertor heat-load width $λ_q$ is a critically important problem for an easier and more robust operation of ITER with high fusion gain. Previous predictive simulation data for $λ_q$ using the extreme-scale edge gyrokinetic code XGC1 in the electrostatic limit under attached divertor plasma conditions in three major US tokamaks [C.S. Chang et al., Nucl. Fusion 57, 116023 (2017)] reproduced the Eich and Goldston attached-divertor formula results [formula #14 in T. Eich et al., Nucl. Fusion 53, 093031 (2013); R.J. Goldston, Nucl. Fusion 52, 013009 (2012)], and further…
For the ITER-like wall, the JET mirror link divertor spectroscopy system was redesigned to fully cover the tungsten horizontal strike plate with faster time resolution and improved near-UV performance. Since the ITER-like wall project involves a change in JET from a carbon dominated machine to a beryllium and tungsten dominated machine with residual carbon, the aim of the system is to provide the recycling flux, equivalent, to the impinging deuterium ion flux, the impurity fluxes (C, Be, O) and tungsten sputtering fluxes and hence give information on the tungsten divertor source. In order to d…
The lithium vapor box divertor aims to detach the divertor plasma via evaporating and condensing lithium surfaces. By evaporating lithium near or at the divertor plate and condensing it closer to the main chamber, a lithium vapor density gradient can be created. This density gradient ties energy losses to poloidal distance between the target and the detachment point. The radiation zone is then prevented from reaching the X-point as the lithium ionization rate decreases when the detachment front moves away from the divertor target. Here we present Scrape Off Layer Plasma Simulator (SOLPS) simul…
The free-streaming plus recycling model (FSRM) has recently been developed to understand and predict tungsten gross erosion rates from the divertor during edge localized modes (ELMs). In this work, the FSRM was tested against experimental measurements of W sputtering during ELMs, conducted via fast WI spectroscopy. Good agreement is observed using a variety of controlling techniques, including gas puffing, neutral beam heating, and plasma shaping to modify the pedestal stability boundary and thus the ELM behavior. ELM mitigation by pellet pacing was observed to strongly reduce W sputtering by …
The effects of the resonant magnetic perturbations (RMPs) on the turbulent transport are analyzed in the framework of the test particle approach using a semi-analytical method. The normalized RMP amplitude $P_{b}$ extends on a large range, from the present experiments to ITER conditions. The results are in agreement with the experiments at small $P_{b}.$ The predictions for ITER strongly depend on the type of turbulent transport. A very strong increase of the turbulent transport is obtained in the nonlinear regime, while the effects of the RMPs are much weaker for the quasilinear transport.
It is planned to use atomic processes to spread out most of the heating power over the first wall and side walls to reduce the heat loads on the plasma facing components in ITER to ~ 50 MW. Calculations indicate that there will be 100 MW in bremstrahlung radiation from the plasma center, 50 MW of radiation from the plasma edge inside the separatrix and 100 MW of radiation from the scrape-off layer and divertor plasma, leaving 50 MW of power to be deposited on the divertor plates. The radiation losses are enhanced by the injection of impurities such as Neon or Argon at acceptably low levels (~0…
The confinement of Neutral Beam Injection (NBI) particles in the presence of n=3 Resonant Magnetic Perturbations (RMPs) in 15 MA ITER DT plasmas has been studied using full orbit ASCOT simulations. Realistic NBI distribution functions, and 3D wall and equilibria, including the plasma response to the externally applied 3D fields calculated with MARS-F, have been employed. The observed total fast-ion losses depend on the poloidal spectra of the applied n=3 RMP as well as on the absolute toroidal phase of the applied perturbation with respect to the NBI birth distribution. The absolute toroidal p…
The complete refuelling of the plasma density loss (pump-out) caused by mitigation of Edge Localised Modes (ELMs) is demonstrated on the ASDEX Upgrade tokamak. The plasma is refuelled by injection of frozen deuterium pellets and ELMs are mitigated by external resonant magnetic perturbations (RMPs). In this experiment relevant dimensionless parameters, such as relative pellet size, relative RMP amplitude and pedestal collisionality are kept at the ITER like values. Refuelling of density pump out requires a factor of two increase of nominal fuelling rate. Energy confinement and pedestal temperat…
Reduction of the peak heat loads on the plasma facing components is essential for the success of the next generation of high fusion power tokamaks such as the International Thermonuclear Experimental Reactor (ITER) 1 . Many present concepts for accomplishing this involve the use of atomic processes to transfer the heat from the plasma to the main chamber and divertor chamber walls and much of the experimental and theoretical physics research in the fusion program is directed toward this issue. The results of these experiments and calculations are the result of a complex interplay of many proce…
Detailed 2D turbulence measurements from the DIII-D tokamak provide an explanation for how resonant magnetic perturbations (RMPs) raise the L-H power threshold $P_\textrm{LH}$ [P. Gohil et al., Nucl. Fusion 51, 103020 (2011)] in ITER-relevant, low rotation, ITER-similar-shape plasmas with favorable ion $\nabla B$ direction. RMPs simultaneously raise the turbulence decorrelation rate $Δω_D$ and reduce the flow shear rate $ω_\textrm{shear}$ in the stationary L-mode state preceding the L-H transition, thereby disrupting the turbulence shear suppression mechanism. RMPs also reduce the Reynolds str…
An analytic theory of edge localized mode (ELM) suppression in an H-mode tokamak plasma via the application of a static, externally generated, resonant magnetic perturbation (RMP) is presented. This theory is based on the plausible hypothesis that mode penetration at the top of the pedestal is a necessary and sufficient condition for the RMP-induced suppression of ELMs. The theory also makes use of a number of key insights gained in a recent publication (Fitzpatrick R 2019). The first insight is that the response of the plasma to a particular helical component of the RMP, in the immediate vici…
Edge-Localized-Mode (ELM) suppression by resonant magnetic perturbations (RMPs) generally occurs over very narrow ranges of the plasma current (or magnetic safety factor q95) in the DIII-D tokamak. However, wide q95 ranges of ELM suppression are needed for the safety and operational flexibility of ITER and future reactors. In DIII-D ITER Similar Shape (ISS) plasmas with n=3 RMPs, the range of q95 for ELM suppression is found to increase with decreasing electron density. Nonlinear two-fluid MHD simulations reproduce the observed q95 windows of ELM suppression and the dependence on plasma densit…
All current estimations of the energy released by type I ELMs indicate that, in order to ensure an adequate lifetime of the divertor targets on ITER, a mechanism is required to decrease the amount of energy released by an ELM, or to eliminate ELMs altogether. One such amelioration mechanism relies on perturbing the magnetic field in the edge plasma region, either leading to more frequent, smaller ELMs (ELM mitigation) or ELM suppression. This technique of Resonant Magnetic Perturbations (RMPs) has been employed to suppress type I ELMs at high collisionality/density on DIII-D, ASDEX Upgrade, KS…
We analyze a Hamiltonian model with five wire loops that delineates the magnetic surfaces of the tokamak ITER, including a similar safety factor profile and the X-point related to the presence of a poloidal divertor. Non-axisymmetric magnetic perturbations are added by external coils, similar to the correction coils installed at the tokamak DIII-D and those that will be installed at ITER. To show the influence of magnetic perturbations on the field line escape, we integrate numerically the field line differential equations and obtain the footprints and deposition patterns on the divertor plate…
Harnessing Toroidal Neutral Flows to Enhance Divertor Particle Exhaust
Gauss Fusion GmbH（高斯聚变有限公司）；Oak Ridge National Laboratory（橡树岭国家实验室）；United Kingdom Atomic Energy Authority（英国原子能管理局）；University of York（约克大学）；RI Research Instruments GmbH（RI研究仪器有限公司）
The guiding-center kinetic neoclassical transport code, XGC0, [C.S. Chang et. al, Phys. Plasmas 11, 2649 (2004)] is used to compute the heat fluxes and the heat-load width in the outer divertor plates of Alcator C-Mod and DIII-D tokamaks. The dependence of the width of heat-load fluxes on neoclassical effects, neutral collisions and anomalous transport is investigated using the XGC0 code. The XGC0 code includes realistic X-point geometry, a neutral source model, the effects of collisions, and a diffusion model for anomalous transport. It is observed that width of the XGC0 neoclassical heat-loa…
The power load to the divertor surfaces is a key concern for future devices such as ITER, due to the thermal limits on the material surface. One factor that characterizes the heat flux to the divertor is the fall off length in the scrape-off layer (SOL), which recent empirical scalings have shown could be as small as 1 mm. These predictions are based on a multi-machine scaling of the heat flux width fitted using an expression for the divertor heat flux profile which includes a term for the exponential decay in the SOL and diffusion about the last closed flux surface (LCFS) in the private flux …
Divertor plasma detachment is likely needed for the function of magnetically confined nuclear fusion. It greatly reduces the particle and heat flux incident on a target, and thus reduces the sputtering and heat loading on the target. It is therefore advantageous to have accurate simulations of plasma behaviour in the divertor to design future Tokamak divertors. A common simulation package used for this purpose is SOLPS-ITER, which has previously been observed to be underestimating the contribution of molecular effects to plasma detachment. To correct this, its reaction rate for molecular charg…
High-power TCV scenario for conventional and alternative divertor studies
Max Planck Institute for Plasma Physics（马克斯·普朗克等离子体物理研究所）；Eindhoven University of Technology（埃因霍温理工大学）；DIFFER - Dutch Institute for Fundamental Energy Research（荷兰基础能源研究院）
MAST-U has recently started operating with a Super-X divertor, designed to increase total flux expansion and neutral trapping, both predicted through simple analytic models and SOLPS calculations to reduce the plasma and impurity density detachment thresholds. In this study, utilising the SOLPS-ITER code, we are quantifying the possible gain allowed by the MAST-U Super-X and neutral baffling geometry, in terms of access to detachment. We show that a significant reduction of the upstream density detachment threshold (up to a factor 1.6) could be achieved in MAST-U, for the Super-X, as opposed t…
Sustained ELM mitigation has been achieved on MAST and AUG using RMPs with a range of toroidal mode numbers over a wide region of low to medium collisionality discharges. The ELM energy loss and peak heat loads at the divertor targets have been reduced. The ELM mitigation phase is typically associated with a drop in plasma density and overall stored energy. In one particular scenario on MAST, by carefully adjusting the fuelling it has been possible to counteract the drop in density and to produce plasmas with mitigated ELMs, reduced peak divertor heat flux and with minimal degradation in pedes…
For understanding carbon erosion and redeposition in nuclear fusion devices, it is important to understand the transport and chemical break-up of hydrocarbon molecules in edge plasmas, often diagnosed by emission of the CH A^2Δ- X^2ΠGerö band around 430 nm. The CH A-level can be excited either by electron-impact or by dissociative recombination (D.R.) of hydrocarbon ions. These processes were included in the 3D Monte Carlo impurity transport code ERO. A series of methane injection experiments was performed in the high-density, low-temperature linear plasma generator Pilot-PSI, and simulated em…
The Mega Amp Spherical Tokamak (MAST) is the centre piece of the UK fusion research programme. In 2010, a MAST Upgrade programme was initiated with three primary objectives, to contribute to: 1) Testing reactor concepts (in particular exhaust solutions via a flexible divertor allowing Super-X and other extended leg configurations); 2) Adding to the knowledge base for ITER (by addressing important plasma physics questions and developing predictive models to help optimise ITER performance of ITER) and 3) Exploring the feasibility of using a spherical tokamak as the basis for a fusion Component T…
Using the orbit-following code ASCOT, we model alpha particle transport in ITER under the influence of ELM control coils (ECCs), toroidal field ripple, and test blanket modules, with emphasis on how the plasma response (PR) modifies the transport mechanisms and fast ion loads on the divertor. We found that while PR shields the plasma by healing broken flux surfaces, it also opens a new loss channel for marginally trapped particles: PR causes strong toroidal variation of the poloidal field near the X-point which leads to de-localisation of banana tips and collisionless transport. The reduction …
Initial evaluation of miniature ultra-high-field commercial stellarator reactors with breeding external to resistive coils
Laboratorio Nacional de Fusión, CIEMAT（国家聚变实验室，CIEMAT）；Departamento de Física, Universidad Carlos III de Madrid（马德里卡洛斯三世大学物理系）；Oak Ridge National Laboratory (ORNL)（橡树岭国家实验室）；University of Texas, Austin（德克萨斯大学奥斯汀分校）
The density dependence of edge-localized-mode (ELM) suppression and density pump-out (density reduction) by n = 2 resonant magnetic perturbations (RMPs) is consistent with the effects of narrow well-separated magnetic islands at the top and bottom of the H-mode pedestal in DIII-D low-collisionality plasmas. Nonlinear two-fluid MHD simulations for DIII-D ITER Similar Shape (ISS) discharges show that, at low collisionality, low pedestal density is required for resonant field penetration at the pedestal top, consistent with the ubiquitous low density requirement for ELM suppression in these DIII-…
