arXivDaily arXiv每日学术速递 周一至周五更新
arXiv周末暂无论文更新,休息一下吧,周末愉快~~
arXiv 2307.11976physics.optics
收藏

去极化穆勒BRDF的高效建模

Efficient Modeling of Depolarizing Mueller BRDFs

Quinn Jarecki, Meredith Kupinski

AI总结:

本研究提出一种三重简并穆勒矩阵pBRDF模型,通过解耦辐射、偏振与去极化属性减少参数,经3D打印物体实验验证,该模型适用于去极化主导材料且鲁棒性良好。

摘要:

室内环境中的光-物质相互作用具有显著的去极化特性。尽管如此,相对较小的偏振属性仍具备信息价值。为利用这一信息,研究人员寻求适用于常见室内材料的偏振BRDF(pBRDF,双向反射分布函数)模型。菲涅尔反射和漫射部分偏振是pBRDF模型中的常用项,但二者的相对贡献高度依赖于材料,且会随散射几何结构和反照率发生变化。高效的pBRDF需以尽可能少的参数描述这些依赖关系,同时保留物理意义和与任务相关的信息。本研究将三重简并(TD)穆勒矩阵(MM)模型与3D打印物体的测量结果进行了对比。在该TD-MM模型中,辐射度、偏振和去极化属性被解耦,以减少参数数量。去极化由一个与几何结构相关的参数量化,四个与几何结构无关的材料常数描述偏振特性,且我们的TD-MM模型被归一化为单位辐射度,从而使BRDF被解耦。为测试TD-MM模型的应用,研究假设了材料常数,并根据线性斯托克斯图像估算了红色3D打印球体的几何结构相关去极化参数。在662 nm(高反照率)条件下,去极化参数的几何平均误差为4.2%;在451 nm(低反照率)条件下,该误差为11.7%。由于误差与反照率和去极化程度成反比,TD-MM模型被认为适用于以去极化为主的材料。研究还通过将真实穆勒图像与红色3D打印斯坦福兔子在任意偏振照明下的外推结果进行对比,测试了TD-MM模型的鲁棒性。

英文摘要:

Light-matter interactions within indoor environments are significantly depolarizing. Nonetheless, the relatively small polarization attributes are informative. To make use of this information, polarized-BRDF (pBRDF) models for common indoor materials are sought. Fresnel reflection and diffuse partial polarization are popular terms in pBRDF models, but the relative contribution of each is highly material-dependent and changes based on scattering geometry and albedo. An efficient pBRDF would describe these dependencies with as few parameters as possible while retaining physical significance and task-relevant information. This work compares a triply-degenerate (TD)-Mueller matrix (MM) model to measurements of 3D printed objects. In this TD-MM model, the radiometric, polarimetric, and depolarization attributes are decoupled to reduce the number of parameters. The depolarization is quantified by a single geometry-dependent parameter, four geometry-independent material constants describe the polarization properties, and our TD-MM model is normalized to unit radiance so that the BRDF is decoupled. To test an application of the TD-MM model the material constants are assumed and the geometry-dependent depolarization parameter for a red 3D printed sphere is estimated from linear Stokes images. The geometry-averaged error of the depolarization parameter is 4.2% at 662 nm (high albedo) and 11.7% at 451 nm (low albedo). Since the error is inversely proportional to albedo and depolarization, the TD-MM model is referred to as appropriate for depolarization-dominant materials. The robustness of the TD-MM model is also tested by comparing ground-truth Mueller images to extrapolations of a red 3D printed Stanford bunny under arbitrary polarized illumination.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑