Analog-to-digital converters (ADCs) allow physical signals to be processed using digital hardware. Their conversion consists of two stages: Sampling, which maps a continuous-time signal into discrete-time, and quantization, i.e., representing the continuous-amplitude quantities using a finite number of bits. ADCs typically implement generic uniform conversion mappings that are ignorant of the task for which the signal is acquired, and can be costly when operating in high rates and fine resolutions. In this work we design task-oriented ADCs which learn from data how to map an analog signal into a digital representation such that the system task can be efficiently carried out. We propose a model for sampling and quantization that facilitates the learning of non-uniform mappings from data. Based on this learnable ADC mapping, we present a mechanism for optimizing a hybrid acquisition system comprised of analog combining, tunable ADCs with fixed rates, and digital processing, by jointly learning its components end-to-end. Then, we show how one can exploit the representation of hybrid acquisition systems as deep network to optimize the sampling rate and quantization rate given the task by utilizing Bayesian meta-learning techniques. We evaluate the proposed deep task-based ADC in two case studies: the first considers symbol detection in multi-antenna digital receivers, where multiple analog signals are simultaneously acquired in order to recover a set of discrete information symbols. The second application is the beamforming of analog channel data acquired in ultrasound imaging. Our numerical results demonstrate that the proposed approach achieves performance which is comparable to operating with high sampling rates and fine resolution quantization, while operating with reduced overall bit rate.
The paper proposes a new method to determine a binary control signal for an analog linear system such that the state, or some output, of the system follows a given target trajectory. The method can also be used for digital-to-analog conversion. The heart of the proposed method is a new binary-enforcing NUV prior (normal with unknown variance). The resulting computations, for each planning period, amount to iterating forward-backward Gaussian message passing recursions (similar to Kalman smoothing), with a complexity (per iteration) that is linear in the planning horizon. In consequence, the pr…
Control-bounded analog-to-digital conversion has many commonalities with delta-sigma conversion, but it can profitably use more general analog filters. The paper describes the operating principle, gives a transfer function analysis, presents a proof-of-concept implementation, and describes the digital filtering in detail.
This paper discusses early results associated with a fully-digital direct-conversion array receiver at 28~GHz. The proposed receiver makes use of commercial off-the-shelf (COTS) electronics, including the receiver chain. The design consists of a custom 28~GHz patch antenna sub-array providing gain in the elevation plane, with azimuthal plane beamforming provided by real-time digital signal processing (DSP) algorithms running on a Xilinx Radio Frequency System on Chip (RF SoC). The proposed array receiver employs element-wise fully-digital array processing that supports ADC sample rates up to 2…
As the bridge between the analog world and digital computers, analog-to-digital converters are generally used in modern information systems such as radar, surveillance, and communications. For the configuration of analog-to-digital converters in future high-frequency broadband systems, we introduce a revolutionary architecture that adopts deep learning technology to overcome tradeoffs between bandwidth, sampling rate, and accuracy. A photonic front-end provides broadband capability for direct sampling and speed multiplication. Trained deep neural networks learn the patterns of system defects, …
Priors with a NUV representation (normal with unknown variance) have mostly been used for sparsity. In this paper, a novel NUV prior is proposed that effectively binarizes. While such a prior may have many uses, in this paper, we explore its use for discrete-level control (with M $\geq$ 2 levels) including, in particular, a practical scheme for digital-to-analog conversion. The resulting computations, for each planning period, amount to iterating forward-backward Gaussian message passing recursions (similar to Kalman smoothing), with a complexity (per iteration) that is linear in the planning …
Line-of-sight (LoS) multi-input multi-output (MIMO) systems exhibit attractive scaling properties with increase in carrier frequency: for a fixed form factor and range, the spatial degrees of freedom increase quadratically for 2D arrays, in addition to the typically linear increase in available bandwidth. In this paper, we investigate whether modern all-digital baseband signal processing architectures can be devised for such regimes, given the difficulty of analog-to-digital conversion for large bandwidths. We propose low-precision quantizer designs and accompanying spatial demultiplexing algo…
Photonic analog to digital conversion offers promise to overcome the signal-to-noise ratio (SNR) and sample rate trade-off in conventional analog to digital converters (ADCs), critical for modern digital communications and signal analysis. We propose using phase-stable dual frequency combs with a fixed frequency spacing offset to downconvert spectral slices of a broadband signal and enable high resolution parallel digitization. To prove the concept of our proposed method, we demonstrate the detection of a 10-GHz subcarrier modulated (SCM) signal using 500-MHz bandwidth ADCs by optically conver…
In a growing number of applications, there is a need to digitize signals whose spectral characteristics are challenging for traditional Analog-to-Digital Converters (ADCs). Examples, among others, include systems where the ADC must acquire at once a very wide but sparsely and dynamically occupied bandwidth supporting diverse services, as well as systems where the signal of interest is subject to strong narrowband co-channel interference. In such scenarios, the resolution requirements can be prohibitively high. As an alternative, the recently proposed modulo-ADC architecture can in principle re…
In a growing number of applications, there is a need to digitize a (possibly high) number of correlated signals whose spectral characteristics are challenging for traditional analog-to-digital converters (ADCs). Examples, among others, include multiple-input multiple-output systems where the ADCs must acquire at once several signals at a very wide but sparsely and dynamically occupied bandwidth supporting diverse services. In such scenarios, the resolution requirements can be prohibitively high. As an alternative, the recently proposed modulo-ADC architecture can in principle require dramatica…
Analog-to-digital (A/D) converters are the common interface between analog signals and the domain of digital discrete-time signal processing. In essence, this domain simultaneously incorporates quantization both in amplitude and time, i.e. amplitude quantization and uniform time sampling. Thus, we view A/D conversion as a sampling process in both the time and amplitude domains based on the observation that the underlying continuous-time signals representing digital sequences can be sampled in a lattice---i.e. at points restricted to lie on a uniform grid both in time and amplitude. We refer to…
Analog-to-digital converters (ADCs) provide the link between continuous-time signals and their discrete-time counterparts, and the Shannon-Nyquist sampling theorem provides the mathematical foundation. Real-world signals have a variable amplitude range, whereas ADCs, by design, have a limited input dynamic range, which results in out-of-range signals getting clipped. In this paper, we propose an unlimited dynamic range ADC (UDR-ADC) that is based on the modulo operation (self-reset feature) to alleviate the problem of clipping. The self-reset feature allows for wrapping of the input amplitudes…
Recent works propose neural network- (NN-) inspired analog-to-digital converters (NNADCs) and demonstrate their great potentials in many emerging applications. These NNADCs often rely on resistive random-access memory (RRAM) devices to realize the NN operations and require high-precision RRAM cells (6~12-bit) to achieve a moderate quantization resolution (4~8-bit). Such optimistic assumption of RRAM resolution, however, is not supported by fabrication data of RRAM arrays in large-scale production process. In this paper, we propose an NN-inspired super-resolution ADC based on low-precision RRAM…
EDA-RoF: Elastic Digital-Analog Radio-Over-Fiber (RoF) Modulation and Demodulation Architecture Enabling Seamless Transition Between Analog RoF and Digital RoF
Hunan Province Key Laboratory of Credible Intelligent Navigation and Positioning, Key Laboratory of Intelligent, Computing and Information Processing of Ministry of Education, National Center for Applied Mathematics in Hunan, Xiangtan University（湘潭大学）；College of Meteorology and Oceanology, National University of Defense Technology（国防科技大学气象海洋学院）
This work aims to relate comparison metrics for both Direct Digital Synthesizers (DDS) and their analog counterparts. The proposed metrics are Total Harmonic Distortion (THD) and maximum absolute error. Error is theoretically formulated into closed forms for known systematic parameters of DDS, sample rate, and bit counts. By the use of Matlab scripting, the system model is simulated for a wide range of parameters sweep.
Based on an equivalent model for quantizers with noisy inputs recently presented in [35], we propose a method of digital dithering at the transmitter that may significantly reduce the resolution requirements of MIMO downlink Digital to Analog Convertors (DAC). We use this equivalent model to analyze the effect of the dither Probability Density Function (PFD), and show that the uniform PDF produces an optimal (linear) result. Relative to other methods of DAC quantization error reduction our approach has the benefits of low computational complexity, compatibility with all existing standards, and…
The level crossing analog-to-digital converters are meant for the effective conversion of sparse signals by construction. In these converters, the bandwidth-power trade-off requires a re-design of the comparators which takes a lot of time and effort to reach the application optimum point. Inspired by synchronous converters that have a dynamic power component that can be traded with bandwidth with the change of a clock frequency, a technique to allow such trade-off in the level crossing converter was developed. The resulting level crossing ADC has an input signal dependent dynamic power which c…
Self-interference (SI) is the main obstacle to full-duplex radios. To overcome the SI, researchers have proposed several analog and digital domain self-interference cancellation (SIC) techniques. How well the digital cancellation works depends on the results of analog cancellation. Therefore, to analyze overall SIC performance, one should do so in an integrated manner. In this paper, we build a simulator that can analyze the performance of analog and digital SIC techniques. Through this simulator, we can analyze the overall SIC performance within various system parameters such as the resolutio…
We propose a new digital-to-analog converter (DAC) for realizing a synapse circuit of mixed-signal spiking neural networks. We named this circuit "time-domain DAC (TDAC)". This produces weights for converting a digital input code into voltage using one current waveform. Therefore, a TDAC is more compact than a conventional DAC that comprises many current sources and resistors. Moreover, a TDAC with leak resistance reproduces biological plausible synaptic responses that are expressed as alpha functions or dual exponential equations. We will show numerical analysis results of a TDAC and circuit …
In this paper, we propose an energy-efficient radar beampattern design framework for a Millimeter Wave (mmWave) massive multi-input multi-output (mMIMO) system, equipped with a hybrid analog-digital (HAD) beamforming structure. Aiming to reduce the power consumption and hardware cost of the mMIMO system, we employ a machine learning approach to synthesize the probing beampattern based on a small number of RF chains and antennas. By leveraging a combination of softmax neural networks, the proposed solution is able to achieve a desirable beampattern with high accuracy.
Spatial linear transforms that process multiple parallel analog signals to simplify downstream signal processing find widespread use in multi-antenna communication systems, machine learning inference, data compression, audio and ultrasound applications, among many others. In the past, a wide range of mixed-signal as well as digital spatial transform circuits have been proposed---it is, however, a longstanding question whether analog or digital transforms are superior in terms of throughput, power, and area. In this paper, we focus on Hadamard transforms and perform a systematic comparison of s…
We study the multi-user massive multiple-input-single-output (MISO) and focus on the downlink systems where the base station (BS) employs hybrid analog-digital precoding with low-cost 1-bit digital-to-analog converters (DACs). In this paper, we propose a hybrid downlink transmission scheme where the analog precoder is formed based on the SVD decomposition. In the digital domain, instead of designing a linear transmit precoding matrix, we directly design the transmit signals by exploiting the concept of constructive interference. The optimization problem is then formulated based on the geometry…
This paper presents a dynamic predictive sampling (DPS) based analog-to-digital converter (ADC) that provides a non-uniform sampling of input analog continuous-time signals. The processing unit generates a dynamic prediction of the input signal using two prior-quantized samplings to compute digital values of an upper threshold and a lower threshold. The digital threshold values are converted to analog thresholds to form a tracking window. A comparator compares the input analog signal with the tracking window to determine if the prediction is successful. A counter records timestamps between the…
In this paper, an on-chip photonic sampled and quantized analog-to-digital converter (ADC) on thin-film lithium niobate platform is experimentally demonstrated. Using two phase modulators as a sampler and a 5$\times$5 multimode interference (MMI) coupler as a quantizer, an 1 GHz sinusoidal analog input signal was successfully converted to a digitized output with a 20 GSample/s sampling rate. To evaluate the system performance, the quantization curves together with the transfer function of the ADC were measured. The experimental effective number of bits (ENOB) was 3.17 bit. The demonstrated dev…
Obtaining digital representations of multivariate continuous-time (CT) signals is a challenge encountered in many signal processing systems. In practice, these signals are often acquired to extract some underlying information, i.e., for a specific task. Employing conventional task-agnostic analog-to-digital converters (ADCs), typically designed to minimize the mean squared error (MSE) in reconstructing the CT input signal, can be costly and energy-inefficient in such cases. In this work, we study task-based ADCs, which are designed to obtain a digital representation of a multivariate CT input …
Digital-to-analog converters (DAC) are indispensable functional units in signal processing instrumentation and wide-band telecommunication links for both civil and military applications. Since photonic systems are capable of high data throughput and low latency, an increasingly found system limitation stems from the required domain-crossing such as digital-to-analog, and electronic-to-optical. A photonic DAC implementation, in contrast, enables a seamless signal conversion with respect to both energy efficiency and short signal delay, often require bulky discrete optical components and electri…
Low-resolution analog-to-digital converters (ADCs) simplify the design of millimeter-wave (mmWave) massive multi-user multiple-input multiple-output (MU-MIMO) basestations, but increase vulnerability to jamming attacks. As a remedy, we propose HERMIT (short for Hybrid jammER MITigation), a method that combines a hardware-friendly adaptive analog transform with a corresponding digital equalizer: The analog transform removes most of the jammer's energy prior to data conversion; the digital equalizer suppresses jammer residues while detecting the legitimate transmit data. We provide theoretical r…
To enable user diversity and multiplexing gains, a fully digital precoding multiple input multiple output (MIMO) architecture is typically applied. However, a large number of radio frequency (RF) chains make the system unrealistic to low-cost communications. Therefore, a practical three-stage hybrid analogue-digital precoding architecture, occupying fewer RF chains, is proposed aiming for a non-orthogonal IoT signal in low-cost multiuser MIMO systems. The non-orthogonal waveform can flexibly save spectral resources for massive devices connections or improve data rate without consuming extra sp…
Convolutional Neural Networks (CNNs) are powerful and highly ubiquitous tools for extracting features from large datasets for applications such as computer vision and natural language processing. However, a convolution is a computationally expensive operation in digital electronics. In contrast, neuromorphic photonic systems, which have experienced a recent surge of interest over the last few years, propose higher bandwidth and energy efficiencies for neural network training and inference. Neuromorphic photonics exploits the advantages of optical electronics, including the ease of analog proce…
Millimeter wave (mmWave) communication has been regarded as one of the most promising technologies for the future generation wireless networks because of its advantages of providing a ultra-wide new spectrum and ultra-high data transmission rate. To reduce the power consumption and circuit cost for mmWave systems, hybrid digital and analog (HDA) architecture is preferred in such a scenario. In this paper, an artificial-noise (AN) aided secure HDA beamforming scheme is proposed for mmWave MISO system with low resolution digital-to-analog converters (DACs) and finite-quantized phase shifters on …
This paper focuses on channel estimation for mmWave MIMO systems with 1-bit spatial sigma-delta analog-to-digital converters (ADCs). The channel estimation performance with 1-bit spatial sigma-delta ADCs depends on the quantization noise modeling. Therefore, we present a new method for modeling the quantization noise by leveraging the deterministic input-output relation of the 1-bit spatial sigma-delta ADC. Using this new noise model, we propose an algorithm for channel estimation for a narrowband single-user mmWave line-of-sight MIMO system by determining the unknown angles and path attenuati…
