Line-of-sight (LoS) multi-input multi-output (MIMO) systems exhibit attractive scaling properties with increase in carrier frequency: for a fixed form factor and range, the spatial degrees of freedom increase quadratically for 2D arrays, in addition to the typically linear increase in available bandwidth. In this paper, we investigate whether modern all-digital baseband signal processing architectures can be devised for such regimes, given the difficulty of analog-to-digital conversion for large bandwidths. We propose low-precision quantizer designs and accompanying spatial demultiplexing algorithms, considering 2x2 LoS MIMO with QPSK for analytical insight, and 4x4 MIMO with QPSK and 16QAM for performance evaluation. Unlike prior work, channel state information is utilized only at the receiver (i.e., transmit precoding is not employed). We investigate quantizers with regular structure whose high-SNR mutual information approaches that of an unquantized system. We prove that amplitude-phase quantization is necessary to attain this benchmark; phase-only quantization falls short. We show that quantizers based on maximizing per-antenna output entropy perform better than standard Minimum Mean Squared Quantization Error (MMSQE) quantization. For spatial demultiplexing with severely quantized observations, we introduce the novel concept of virtual quantization which, combined with linear detection, provides reliable demodulation at significantly reduced complexity compared to maximum likelihood detection.
Knowledge of second-order statistics of channels (e.g. in the form of covariance matrices) is crucial for the acquisition of downlink channel state information (CSI) in massive MIMO systems operating in the frequency division duplexing (FDD) mode. Current MIMO systems usually obtain downlink covariance information via feedback of the estimated covariance matrix from the user equipment (UE), but in the massive MIMO regime this approach is infeasible because of the unacceptably high training overhead. This paper considers instead the problem of estimating the downlink channel covariance from upl…
We experimentally test the compliance with 5G/NR 3GPP technical specifications of an analog radio-over-FSO link at 9 μm. The ACLR and EVM transmitter requirements are fulfilled validating the suitability of LWIR FSO for 6G fronthaul.
In this paper, we propose an energy-efficient radar beampattern design framework for a Millimeter Wave (mmWave) massive multi-input multi-output (mMIMO) system, equipped with a hybrid analog-digital (HAD) beamforming structure. Aiming to reduce the power consumption and hardware cost of the mMIMO system, we employ a machine learning approach to synthesize the probing beampattern based on a small number of RF chains and antennas. By leveraging a combination of softmax neural networks, the proposed solution is able to achieve a desirable beampattern with high accuracy.
Multiple-input multiple-output (MIMO) systems exploit spatial diversity to facilitate multi-user communications with high spectral efficiency by beamforming. As MIMO systems utilize multiple antennas and radio frequency (RF) chains, they are typically costly to implement and consume high power. A common method to reduce the cost of MIMO receivers is utilizing less RF chains than antennas by employing hybrid analog/digital beamforming (HBF). However, the added analog circuitry involves active components whose consumed power may surpass that saved in RF chain reduction. An additional method to r…
In this paper, we propose an intelligent analog beam selection strategy in a terahertz (THz) band beamspace multiple-input multiple-output (MIMO) system. First inspired by transfer learning, we fine-tune the pre-trained off-the-shelf GoogleNet classifier, to learn analog beam selection as a multi-class mapping problem. Simulation results show 83% accuracy for the analog beam selection, which subsequently results in 12% spectral efficiency (SE) gain, upon the existing counterparts. Towards a more accurate classifier, we replace the conventional rectified linear unit (ReLU) activation function o…
Beamforming gain is a key ingredient in the performance of LEO satellite communication systems to be integrated into cellular networks. However, beam codebooks previously designed in the context of MIMO communication for terrestrial networks, do not provide the appropriate performance in terms of inter-beam interference and gain stability as the satellite moves. In this paper, we propose a dynamic codebook that provides a stable gain during the period of time that the satellite covers a given cell, while avoiding link retraining and extra calculation as the satellite moves. In addition, the pr…
A digitally-assisted photonic analog domain self-interference cancellation (SIC) and frequency downconversion method is proposed for in-band full-duplex multiple-input multiple-output (MIMO) systems using the least square (LS) algorithm with adaptive order. The SIC and frequency downconversion are achieved in the optical domain via a dual-parallel Mach-Zehnder modulator (DP-MZM), while the downconverted signal is processed by the LS algorithm with adaptive order that is used to track the response of the multipath self-interference (SI) channel and reconstruct the reference signal for SIC. The …
Hybrid beamforming is considered a key enabler to realize millimeter wave (mmWave) multiple-input multiple-output (MIMO) communications due to its capability of considerably reducing the number of costly and power-hungry radio frequency chains in the transceiver. However, in mmWave MIMO orthogonal frequency-division multiplexing (MIMO-OFDM) systems, hybrid beamforming design is challenging because the analog precoder and combiner are required to be shared across the whole employed bandwidth. In this paper, we propose closed-form solutions to the problem of designing the analog precoder/combine…
We derive novel bounds for the performance of algorithms that estimate the downlink covariance matrix from the uplink covariance matrix in frequency division duplex (FDD) massive multiple-input multiple-output (MIMO) systems. The focus is on algorithms that use estimates of the angular power spectrum as an intermediate step. Unlike previous results, the proposed bounds follow from simple arguments in possibly infinite dimensional Hilbert spaces, and they do not require strong assumptions on the array geometry or on the propagation model. Furthermore, they are suitable for the analysis of set-t…
Control-bounded analog-to-digital conversion has many commonalities with delta-sigma conversion, but it can profitably use more general analog filters. The paper describes the operating principle, gives a transfer function analysis, presents a proof-of-concept implementation, and describes the digital filtering in detail.
In a cell-free cloud radio access network (C-RAN) architecture, uplink channel estimation is carried out by a centralized baseband processing unit (BBU) connected to distributed remote radio heads (RRHs). When the RRHs have multiple antennas and limited radio front-end resources, the design of uplink channel estimation is faced with the challenges posed by reduced radio frequency (RF) chains and one-bit analog-to-digital converters (ADCs) at the RRHs. This work tackles the problem of jointly optimizing the pilot sequences and the pre-RF chains analog combiners with the goal of minimizing the s…
Advances in analog-to-digital converter (ADC) technology have opened up the possibility to directly digitize wideband radio frequency (RF) signals, avoiding the need for analog down-conversion. In this work, we consider an orthogonal frequency-division multiplexing (OFDM)-based massive multi-user (MU) multiple-input multiple-output (MIMO) uplink system that relies on direct RF-sampling at the base station and digitizes the received RF signals with 1-bit ADCs. Using Bussgang's theorem, we provide an analytical expression for the error-vector magnitude (EVM) achieved by digital down-conversion a…
In this paper, we present a fixed mmWave Multi-User Multiple-Input Multiple-Output (MIMO) system for fixed wireless access with a unique architecture. A digital MIMO system is combined with an analog multi-beam antenna array which uses a high-dimension 16x16 Butler matrix to obtain 16 orthogonal beams. A system model of this architecture is presented and used to simulate its performance comparing to the performance of common-used patch antennas. Several MIMO precoding techniques are considered and compared with basic analog beamforming. To verify these results, a prototype is built and a dedic…
In this paper, we focus on reduced complexity full duplex Multiple-Input Multiple-Output (MIMO) systems and present a joint design of digital transmit and receive beamforming with Analog and Digital (A/D) self-interference cancellation. We capitalize on a recently proposed multi-tap analog canceller architecture, whose number of taps does not scale with the number of transceiver antennas, and consider practical transmitter impairments for the full duplex operation. Particularly, transmitter IQ imbalance and nonlinear power amplification are assumed via relevant realistic models. Aiming at supp…
This paper investigates adaptive signal shaping methods for millimeter wave (mmWave) multiple-input multiple-output (MIMO) communications based on the maximizing the minimum Euclidean distance (MMED) criterion. In this work, we utilize the indices of analog precoders to carry information and optimize the symbol vector sets used for each analog precoder activation state. Specifically, we firstly propose a joint optimization based signal shaping (JOSS) approach, in which the symbol vector sets used for all analog precoder activation states are jointly optimized by solving a series of quadratical…
Signal processing in wireless communications, such as precoding, detection, and channel estimation, are basically about solving inverse matrix problems, which, however, are slow and inefficient in conventional digital computers, thus requiring a radical paradigm shift to achieve fast, real-time solutions. Here, for the first time, we apply the emerging analog matrix computing (AMC) to the linear precoding of massive MIMO. The real-valued AMC concept is extended to process complex-valued signals. In order to adapt the MIMO channel models to RRAM conductance mapping, a new matrix inversion circu…
Recent years have witnessed growing interest in reduced cost radar systems operating with low power. Multiple-input multiple-output (MIMO) radar technology is known to achieve high performance sensing by probing with multiple orthogonal waveforms. However, implementing a low cost low power MIMO radar is challenging. One of the reasons for this difficulty stems from the increased cost and power consumption required by analog-to-digital convertors (ADCs) in acquiring the multiple waveforms at the radar receiver. In this work we study reduced cost MIMO radar receivers restricted to operate with l…
Based on an equivalent model for quantizers with noisy inputs recently presented in [35], we propose a method of digital dithering at the transmitter that may significantly reduce the resolution requirements of MIMO downlink Digital to Analog Convertors (DAC). We use this equivalent model to analyze the effect of the dither Probability Density Function (PFD), and show that the uniform PDF produces an optimal (linear) result. Relative to other methods of DAC quantization error reduction our approach has the benefits of low computational complexity, compatibility with all existing standards, and…
In this paper, we provide an analytical framework for full-duplex (FD) massive multiple-input multiple-output (MIMO) cellular networks with low resolution analog-to-digital and digital-to-analog converters (ADCs and DACs). Matched filters are employed at the FD base stations (BSs) at the transmit and receive sides. For both reverse and forward links, our contributions are (1) derivations of the signal-to-quantization-plus-interference-and-noise ratio (SQINR) for general and special cases; (2) derivations of spectral efficiency for asymptotic cases as well as for power scaling laws; and (3) qua…
Column-Wise Analog Processing for Hybrid Precoding in Millimeter Wave Downlink Multi-User Massive MIMO Systems
Tsinghua University（清华大学）；Chinese Academy of Sciences（中国科学院）；University of Chinese Academy of Sciences（中国科学院大学）；Communication University of China（中国传媒大学）
Millimeter-wave and terahertz technologies have been attracting attention from the wireless research community since they can offer large underutilized bandwidths which can enable the support of ultra-high-speed connections in future wireless communication systems. While the high signal attenuation occurring at these frequencies requires the adoption of very large (or the so-called ultra-massive) antenna arrays, in order to accomplish low complexity and low power consumption, hybrid analog/digital designs must be adopted. In this paper we present a hybrid design algorithm suitable for both mmW…
We consider a bidirectional in-band full-duplex (FD) multiple-input multiple-output (MIMO) system subject to imperfect channel state information (CSI), hardware distortion, and limited analog cancellation capability as well as the self-interference (SI) power requirement at the receiver analog domain so as to avoid the saturation of low noise amplifier (LNA). A novel minimum mean square error (MMSE)-based joint design of digital precoder and combiner for SI cancellation is offered, which combines the well-known gradient projection method and non-monotonicity considered in recent machine-learni…
Hybrid analog and digital beamforming has emerged as a key enabling technology for millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) communication systems since it can balance the trade-off between system performance and hardware efficiency. Owing to the strong ability of central control, cooperative networks show great potential to enhance the spectral efficiency of mmWave communications. In this paper, we consider cooperative mmWave MIMO systems and propose user association and hybrid beamforming design algorithms for three typical hybrid beamforming architectures. The c…
Photonics-assisted analog wideband self-interference cancellation for in-band full-duplex MIMO systems with adaptive digital amplitude and delay pre-matching
Hybrid beamforming has evolved as a promising technology that offers the balance between system performance and design complexity in mmWave MIMO systems. Existing hybrid beamforming methods either impose unit-modulus constraints or a codebook constraint on the analog precoders/combiners, which in turn results in a performance-overhead tradeoff. This paper puts forth a tensor framework to handle the wideband hybrid beamforming problem, with Vandermonde constraints on the analog precoders/combiners. The proposed method strikes the balance between performance, overhead and complexity. Numerical r…
Analog to Digital Converters (ADCs) are a major contributor to the energy consumption on the receiver side of millimeter-wave multiple-input multiple-output (MIMO) systems with large antenna arrays. Consequently, there has been significant interest in using low-resolution ADCs along with hybrid beam-forming at MIMO receivers for energy efficiency. However, decreasing the ADC resolution results in performance loss -- in terms of achievable rates -- due to increased quantization error. In this work, we study the application of practically implementable nonlinear analog operations, prior to sampl…
Hybrid analog/digital architectures and receivers with low-resolution analog-to-digital converters (ADCs) are two low power solutions for wireless systems with large antenna arrays. Most prior work represents two extreme cases in which either a small number of radio frequency (RF) chains with full-resolution ADCs, or low-resolution ADC with a number of RF chains equal to the number of antennas is assumed. In this paper, a generalized hybrid architecture with a small number of RF chains and a finite number of ADC bits is proposed. In such a system, the received signal suffers from two compressi…
Analog Multiple-Input Multiple-Output Radio-over-Copper (A-MIMO-RoC) is an effective all-analog FrontHaul (FH) architecture that exploits any pre-existing Local Area Network (LAN) cabling infrastructure of buildings to distribute Radio-Frequency (RF) signals indoors. A-MIMO-RoC, by leveraging a fully analog implementation, completely avoids any dedicated digital interface by using a transparent end-to-end system, with consequent latency, bandwidth and cost benefits. Usually, LAN cables are exploited mainly in the low-frequency spectrum portion, mostly due to the moderate cable attenuation and …
In this letter, we study the performance of a downlink multiuser massive multiple-input multiple-output (MIMO) system with sub-connected structure over limited feedback channels. Tight rate approximations are theoretically analyzed for the system with pure analog precoding and hybrid precoding. The effect of quantized analog and digital precoding is characterized in the derived expressions. Furthermore, it is revealed that the pure analog precoding outperforms the hybrid precoding using maximal-ratio transmission (MRT) or zero forcing (ZF) under certain conditions, and we theoretically charact…
Most of the indoor coverage issues arise from network deployments that are usually planned for outdoor scenarios. Moreover, the ever-growing number of devices with different Radio Access Technologies (RATs), expected for new 5G scenarios and to maintain compatibility with older cellular standards (mostly 3G/4G), worsen this situation thus calling for novel bandwidth-efficient, low-latency and cost-effective solutions for indoor coverage. To solve this problem, Centralized Radio Access Network (C-RAN) architectures have been proposed to provide dense and controlled coverage inside buildings. Ho…
The use of 1-bit analog-to-digital converters (ADCs) is seen as a promising approach to significantly reduce the power consumption and hardware cost of multiple-input multiple-output (MIMO) receivers. However, the nonlinear distortion due to 1-bit quantization fundamentally changes the optimal communication strategy and also imposes a capacity penalty to the system. In this paper, the capacity of a Gaussian MIMO channel in which the antenna outputs are processed by an analog linear combiner and then quantized by a set of zero threshold ADCs is studied. A new capacity upper bound for the zero t…
This paper focuses on channel estimation for mmWave MIMO systems with 1-bit spatial sigma-delta analog-to-digital converters (ADCs). The channel estimation performance with 1-bit spatial sigma-delta ADCs depends on the quantization noise modeling. Therefore, we present a new method for modeling the quantization noise by leveraging the deterministic input-output relation of the 1-bit spatial sigma-delta ADC. Using this new noise model, we propose an algorithm for channel estimation for a narrowband single-user mmWave line-of-sight MIMO system by determining the unknown angles and path attenuati…
Priors with a NUV representation (normal with unknown variance) have mostly been used for sparsity. In this paper, a novel NUV prior is proposed that effectively binarizes. While such a prior may have many uses, in this paper, we explore its use for discrete-level control (with M $\geq$ 2 levels) including, in particular, a practical scheme for digital-to-analog conversion. The resulting computations, for each planning period, amount to iterating forward-backward Gaussian message passing recursions (similar to Kalman smoothing), with a complexity (per iteration) that is linear in the planning …
Hybrid digital/analog architecture and low-resolution analog-to-digital/digital-to-analog converters (ADCs /DACs) are two low-cost implementations for large-scale millimeter wave (mmWave) systems. In this paper, we investigate the problem of constant-envelope transmit beamforming for large-scale multiple-input multiple-output (MIMO) radar system, where the transmit array adopts a hybrid digital/analog architecture with a small number of RF chains and the receive array adopts a fully digital architecture with low-resolution ADCs. We derive the relative entropy between the probability density fu…
In this paper, we propose a wideband Full Duplex (FD) Multiple-Input Multiple-Output (MIMO) communication system comprising of an FD MIMO node simultaneously communicating with two multi-antenna UpLink (UL) and DownLink (DL) nodes utilizing the same time and frequency resources. To suppress the strong Self-Interference (SI) signal due to simultaneous transmission and reception in FD MIMO systems, we propose a joint design of Analog and Digital (A/D) cancellation as well as transmit and receive beamforming capitalizing on baseband Orthogonal Frequency-Division Multiplexing (OFDM) signal modelin…
Low resolution analog-to-digital converters (ADCs) can be employed to improve the energy efficiency (EE) of a wireless receiver since the power consumption of each ADC is exponentially related to its sampling resolution and the hardware complexity. In this paper, we aim to jointly optimize the sampling resolution, i.e., the number of ADC bits, and analog/digital hybrid combiner matrices which provides highly energy efficient solutions for millimeter wave multiple-input multiple output systems. A novel decomposition of the hybrid combiner to three parts is introduced: the analog combiner matrix…
Performance Analysis of Digital Beamforming mmWave MIMO with Low-Resolution DACs/ADCs
TU Wien（维也纳工业大学）；Christian Doppler Laboratory for Digital Twin assisted AI for sustainable Radio Access Networks（可持续无线接入网数字孪生辅助AI克劳迪普勒实验室）；Lund University（隆德大学）
Both the power-dissipation and cost of massive multiple-input multiple-output (mMIMO) systems may be substantially reduced by using low-resolution analog-to-digital converters (LADCs) at the receivers. However, both the coarse quantization of LADCs and the inaccurate instantaneous channel state information (ICSI) degrade the performance of quantized mMIMO systems. To overcome these challenges, we propose a novel stochastic hybrid analog-digital combiner (SHC) scheme for adapting the hybrid combiner to the long-term statistics of the channel state information (SCSI). We seek to minimize the tra…
Based on a new equivalent model of quantizer with noisy input recently presented in [23], we propose a new low complexity receiver that takes into account the nonlinear distortion (NLD) generated by Analog to Digital converter (ADC) with insufficient resolution. The strength of new model is that it presents the NLD as a function of only the desired part of input signal (without noise). Therefore it can easily be used in a variety of NLD mitigation techniques. Here, as an illustration of this, we use a pseudo-ML approach to detect the original QAM modulation based on the equivalent transfer fun…
Massive multiple-input multiple-output (MIMO) systems require downlink channel state information (CSI) at the base station (BS) to better utilize the available spatial diversity and multiplexing gains. However, in a frequency division duplex (FDD) massive MIMO system, CSI feedback overhead degrades the overall spectral efficiency. Convolutional neural network (CNN)-based CSI feedback compression schemes has received a lot of attention recently due to significant improvements in compression efficiency; however, they still require reliable feedback links to convey the compressed CSI information …
In this paper, we study Full Duplex (FD) Multiple-Input Multiple-Output (MIMO) radios for simultaneous data communication and control information exchange. Capitalizing on a recently proposed FD MIMO architecture combining digital transmit and receive beamforming with reduced complexity multi-tap analog Self-Interference (SI) cancellation, we propose a novel transmission scheme exploiting channel reciprocity for joint downlink beamformed information data communication and uplink channel estimation through training data transmission. We adopt a general model for pilot-assisted channel estimatio…
Low-resolution analog-to-digital converters (ADCs) simplify the design of millimeter-wave (mmWave) massive multi-user multiple-input multiple-output (MU-MIMO) basestations, but increase vulnerability to jamming attacks. As a remedy, we propose HERMIT (short for Hybrid jammER MITigation), a method that combines a hardware-friendly adaptive analog transform with a corresponding digital equalizer: The analog transform removes most of the jammer's energy prior to data conversion; the digital equalizer suppresses jammer residues while detecting the legitimate transmit data. We provide theoretical r…
