Reconfigurable Intelligent Surface (RIS) is a promising solution to reconfigure the wireless environment in a controllable way. To compensate for the double-fading attenuation in the RIS-aided link, a large number of passive reflecting elements (REs) are conventionally deployed at the RIS, resulting in large surface size and considerable circuit power consumption. In this paper, we propose a new type of RIS, called active RIS, where each RE is assisted by active loads (negative resistance), that reflect and amplify the incident signal instead of only reflecting it with the adjustable phase shift as in the case of a passive RIS. Therefore, for a given power budget at the RIS, a strengthened RIS-aided link can be achieved by increasing the number of active REs as well as amplifying the incident signal. We consider the use of an active RIS to a single input multiple output (SIMO) system. {However, it would unintentionally amplify the RIS-correlated noise, and thus the proposed system has to balance the conflict between the received signal power maximization and the RIS-correlated noise minimization at the receiver. To achieve this goal, it has to optimize the reflecting coefficient matrix at the RIS and the receive beamforming at the receiver.} An alternating optimization algorithm is proposed to solve the problem. Specifically, the receive beamforming is obtained with a closed-form solution based on linear minimum-mean-square-error (MMSE) criterion, while the reflecting coefficient matrix is obtained by solving a series of sequential convex approximation (SCA) problems. Simulation results show that the proposed active RIS-aided system could achieve better performance over the conventional passive RIS-aided system with the same power budget.
The design of feedback channels in frequency division duplex (FDD) systems is a major challenge because of the limited available feedback bits. We consider non-orthogonal multiple access (NOMA) systems that incorporate reconfigurable intelligent surfaces (RISs). In limited feedback RIS-aided NOMA systems, the RIS-aided channel and the direct channel gains should be quantized and fed back to the transmitter. This paper investigates the rate loss of the overall RIS-aided NOMA systems suffering from quantization errors. We first consider random vector quantization for the overall RIS-aided channe…
In reconfigurable intelligent surfaces (RISs) aided communications, the existing passive beamforming (PB) design involves polynomial complexity in the number of reflecting elements, and thus is difficult to implement due to a massive number of reflecting elements. To overcome this difficulty, we propose a reflection-angle-based cascaded channel model by adopting the generalized Snell's law, in which the dimension of the variable space involved in optimization is significantly reduced, resulting in a simplified hierarchical passive beamforming (HPB) design. We develop an efficient two-stage HPB…
Rate-splitting multiple access (RSMA) has been recognized as a promising and powerful multiple access (MA) scheme, non-orthogonal transmission framework and interference management strategy for 6G. Inspired by the appealing spectral efficiency gain achieved by RSMA over conventional MA schemes in multi-user multi-antenna transmission, in this paper we introduce RSMA to reconfigurable intelligent surface (RIS)-aided multiple-input single-out (MISO) broadcast channel (BC). To further enhance the spectral efficiency, a more generalized RIS architecture called fully connected RIS is considered. By…
Reconfigurable intelligent surfaces (RISs) become promising for enhancing non-orthogonal multiple access (NOMA) systems, i.e., enhancing the channel quality and altering the SIC orders. Invoked by stochastic geometry methods, we investigate the downlink coverage performance of RIS-aided multi-cell NOMA networks. We first derive the RIS-aided channel model, concluding the direct and reflecting links. The analytical results demonstrate that the RIS-aided channel model can be closely modeled as a Gamma distribution. Additionally, interference from other cells is analyzed. Lastly, we derive closed…
To achieve the joint active and passive beamforming gains in the reconfigurable intelligent surface assisted millimeter wave system, the reflected cascade channel needs to be accurately estimated. Many strategies have been proposed in the literature to solve this issue. However, whether the Cramér-Rao lower bound (CRLB) of such estimation is achievable still remains uncertain. To fill this gap, we first convert the channel estimation problem into a sparse signal recovery problem by utilizing the properties of discrete Fourier transform matrix and Kronecker product. Then, a joint typicality bas…
Recently, reconfigurable intelligent surface (RIS), a planar metasurface consisting of a large number of low-cost reflecting elements, has received much attention due to its ability to improve both the spectrum and energy efficiencies by reconfiguring the wireless propagation environment. In this paper, we propose a RIS phase shift and BS beamforming optimization technique that minimizes the uplink transmit power of a RIS-aided IoT network. Key idea of the proposed scheme, referred to as Riemannian conjugate gradient-based joint optimization (RCG-JO), is to jointly optimize the RIS phase shift…
By activating blocked users and altering successive interference cancellation (SIC) sequences, reconfigurable intelligent surfaces (RISs) become promising for enhancing non-orthogonal multiple access (NOMA) systems. The downlink RIS-aided NOMA networks are investigated via stochastic geometry. We first introduce the unique path loss model for RIS reflecting channels. Then, we evaluate the angle distributions based on a Poisson cluster process (PCP) model, which theoretically demonstrates that the angles of incidence and reflection are uniformly distributed. Additionally, we derive closed-form …
By activating blocked users and altering successive interference cancellation (SIC) sequences, reconfigurable intelligent surfaces (RISs) become promising for enhancing non-orthogonal multiple access (NOMA) systems. This work investigates the downlink performance of RIS-aided NOMA networks via stochastic geometry. We first introduce the unique path loss model for RIS reflecting channels. Then, we evaluate the angle distributions based on a Poisson cluster process (PCP) framework, which theoretically demonstrates that the angles of incidence and reflection are uniformly distributed. Lastly, we …
Current scene depth estimation approaches mainly rely on optical sensing, which carries privacy concerns and suffers from estimation ambiguity for distant, shiny, and transparent surfaces/objects. Reconfigurable intelligent surfaces (RISs) provide a path for employing a massive number of antennas using low-cost and energy-efficient architectures. This has the potential for realizing RIS-aided wireless sensing with high spatial resolution. In this paper, we propose to employ RIS-aided wireless sensing systems for scene depth estimation. We develop a comprehensive framework for building accurate…
The advantages of millimeter-wave and large antenna arrays technologies for accurate wireless localization received extensive attentions recently. However, how to further improve the accuracy of wireless localization, even in the case of obstructed line-of-sight, is largely undiscovered. In this paper, the reconfigurable intelligent surface (RIS) is introduced into the system to make the positioning more accurate. First, we establish the three-dimensional RIS-assisted wireless localization channel model. After that, we derive the Fisher information matrix and the Cramer-Rao lower bound for eva…
A two-user downlink network aided by a reconfigurable intelligent surface is considered. The weighted sum signal to interference plus noise ratio maximization and the sum rate maximization models are presented, where the precoding vectors and the RIS matrix are jointly optimized. Since the optimization problem is non-convex and difficult, new approximation models are proposed. The upper bounds of the corresponding objective functions are derived and maximized. Two new algorithms based on the alternating direction method of multiplier are proposed. It is proved that the proposed algorithms conv…
We consider a reconfigurable intelligent surface (RIS)-aided massive multi-user multiple-input multiple-output (MIMO) communication system with transceiver hardware impairments (HWIs) and RIS phase noise. Different from the existing contributions, the phase shifts of the RIS are designed based on the long-term angle informations. Firstly, an approximate analytical expression of the uplink achievable rate is derived. Then, we use genetic algorithm (GA) to maximize the sum rate and the minimum date rate. Finally, we show that it is crucial to take HWIs into account when designing the phase shift…
This paper investigates the performance of reconfigurable intelligent surface (RIS)-aided massive multiple-input multiple-output (MIMO) systems with direct links, and the phase shifts of the RIS are designed based on the statistical channel state information (CSI). We first derive the closed-form expression of the uplink ergodic data rate. Then, based on the derived expression, we use the genetic algorithm (GA) to solve the sum data rate maximization problem. With low-complexity maximal-ratio combination (MRC) and low-overhead statistical CSI-based scheme, we validate that the RIS can still br…
In this letter, we investigate joint application of reconfigurable intelligent surface (RIS) and vertical beamforming in cognitive radio networks (CRN). After properly modeling the network, an optimization problem is formed to jointly design the beamforming vector and tilt angle at the secondary base station (BS) as well as the phase shifts at the RIS with the objective of maximizing spectral efficiency of the secondary network. The optimization problem is non-convex; thus, we propose an efficient solution method for it. Numerical results show that adding a RIS and optimizing the radiation ori…
Reconfigurable intelligent surfaces have emerged as a promising technology for future wireless networks. Given that a large number of reflecting elements is typically used, and that the surface has no signal processing capabilities, a major challenge is to cope with the overhead that is required to estimate the channel state information and to report the optimized phase shifts to the surface. This issue has not been addressed by previous works, which do not explicitly consider the overhead during the resource allocation phase. This work aims at filling this gap, developing an overhead-aware re…
Reconfigurable intelligent surface (RIS)-aided networks have been investigated for the purpose of improving the system performance. However, the introduced unit modulus phase shifts and coupling characteristic bring enormous challenges to the optimization in the RIS-aided networks. Many efforts have been made to jointly optimize phase shift vector and other parameters. This article intends to survey the latest research results about the optimization in RIS-aided networks. A taxonomy is devised to categorize the existing literatures based on optimization types, phase shift form, and decoupling …
In this paper, we focus our attention on the mitigation of beam squint for reconfigurable intelligent surface (RIS) aided wideband millimeter wave (mmWave) communications. Due to the intrinsic passive property, the phase shifts of all elements in RIS should be the same for all frequencies. However, in the wideband scenario, beam squint induced distinct path phases require designing different phase shifts for different frequencies. The above irreconcilable contradiction will dramatically affect the system performance, considering the RIS usually consists of enormous elements and the bandwidth o…
The reconfigurable intelligent surface (RIS) has arose an upsurging research interest recently due to its promising outlook in 5G-and-beyond wireless networks. With the assistance of RIS, the wireless propagation environment is no longer static and could be customized to support diverse service requirements. In this paper, we will approach the rate maximization problems in RIS-aided wireless networks by considering the beamforming and reflecting design jointly. Three representative design problems from different system settings are investigated based on a proposed unified algorithmic framework…
In this work, we consider the target detection problem in a sensing architecture where the radar is aided by a reconfigurable intelligent surface (RIS), that can be modeled as an array of sub-wavelength small reflective elements capable of imposing a tunable phase shift to the impinging waves and, ultimately, of providing the radar with an additional echo of the target. A theoretical analysis is carried out for closely- and widely-spaced (with respect to the target) radar and RIS and for different beampattern configurations, and some examples are provided to show that large gains can be achiev…
This paper presents a quantified assessment of the physical layer security capabilities of reconfigurable intelligent surface (RIS)-aided wireless systems under eavesdropping. Specifically, we derive a closed-form expression for the ergodic secrecy capacity (ESC) that is adaptable to different types of fading and RIS size. The channels between the transmitter (TX) and RIS, the RIS and legitimate receiver as well as the TX and eavesdropper are assumed to follow independent mixture Gamma (MG) distributions. Note that MG is capable of modeling a large variety of well-known distributions, includin…
In this paper, we propose and investigate an aerial reconfigurable intelligent surface (aerial-RIS)-aided wireless communication system. Specifically, considering practical composite fading channels, we characterize the air-to-ground (A2G) links by Namkagami-m small-scale fading and inverse-Gamma large-scale shadowing. To investigate the delay-limited performance of the proposed system, we derive a tight approximate closed-form expression for the end-to-end outage probability (OP). Next, considering a mobile environment, where performance analysis is intractable, we rely on machine learning-ba…
Reconfigurable Intelligent Surface (RIS) draws great attentions in academic and industry due to its passive and low power consumption nature, and has currently been used in physical layer security to enhance the secure transmission. However, due to the existence of double fading effect on the reflecting channel link between transmitter and user, RIS helps achieve limited secrecy performance gain compared with the case without RIS. In this correspondence, we propose a novel active RIS design to enhance the secure wireless transmission, where the reflecting elements in RIS not only adjust the ph…
Reconfigurable intelligent surface (RIS) provides a promising way to build the programmable wireless transmission environments in the future. Owing to the large number of reflecting elements used at the RIS, joint optimization for the active beamforming at the transmitter and the passive reflector at the RIS is usually complicated and time-consuming. To address this problem, this paper proposes a low-complexity joint beamforming and reflecting algorithm based on fractional programing (FP). Specifically, we first consider a RIS-aided multi-user communication system with perfect channel state in…
Reconfigurable intelligent surfaces (RISs) have emerged as a promising technique to enhance the system spectral efficiency. This paper investigates the ergodic channel capacity (ECC) of an RIS-aided multiple-input multiple-output channel under the assumption that the transmitter-RIS, RIS-receiver, and transmitter-receiver channels contain deterministic line-of-sight paths. Novel expressions are derived to characterize the upper and lower bounds of the ECC. To unveil more system insights, asymptotic analyses are performed to the system ECC in the limit of large signal-to-noise ratio (SNR) and n…
This letter investigates the reconfigurable intelligent surface (RIS)-aided massive multiple-input multiple-output (MIMO) systems with a two-timescale design. First, the zero-forcing (ZF) detector is applied at the base station (BS) based on instantaneous aggregated CSI, which is the superposition of the direct channel and the cascaded user-RIS-BS channel. Then, by leveraging the channel statistical property, we derive the closed-form ergodic achievable rate expression. Using a gradient ascent method, we design the RIS passive beamforming only relying on the long-term statistical CSI. We prove…
This paper focuses on studying orthogonal and non-orthogonal multiple access in intelligent reflecting surface (IRS)-aided systems. Unlike most prior works assuming continuous phase shifts, we employ the practical setup where only a finite number of discrete phase shifts are available. To maximize the sum rate, active beamforming and discrete reflection need to be jointly optimized. We therefore propose an alternative optimization method to get the optimal continuous phase shifts iteratively, and then quantize each phase shift to its nearest discrete value. The sum-rate maximization of differe…
This work considers a point-to-point link where a reconfigurable intelligent surface assists the communication between transmitter and receiver. The system rate, energy efficiency, and their trade-off are optimized with respect to the number of individually tunable elements of the intelligent surface. The resource allocation accounts for the communication phase and for the overhead due to channel estimation and to reporting the optimized resource allocation to the intelligent surface. Numerical results confirm the optimality of the proposed methods and show the potential gains of reconfigurabl…
Reconfigurable intelligent surface (RIS)-aided wireless communications have drawn significant attention recently. We study the physical layer security of the downlink RIS-aided transmission framework for randomly located users in the presence of a multi-antenna eavesdropper. To show the advantages of RIS-aided networks, we consider two practical scenarios: Communication with and without RIS. In both cases, we apply the stochastic geometry theory to derive exact probability density function (PDF) and cumulative distribution function (CDF) of the received signal-to-interference-plus-noise ratio.…
Reconfigurable intelligent surface (RIS) is envisioned to be a promising green technology to reduce the energy consumption and improve the coverage and spectral efficiency of massive multiple-input multiple-output (MIMO) wireless networks. In a RIS-aided MIMO system, the acquisition of channel state information (CSI) is important for achieving passive beamforming gains of the RIS, but is also challenging due to the cascaded property of the transmitter-RIS-receiver channel and the lack of signal processing capability of the passive RIS elements. The state-of-the-art approach for CSI acquisition…
This article aims to reduce huge pilot overhead when estimating the reconfigurable intelligent surface (RIS) relayed wireless channel. Motivated by the compelling grasp of deep learning in tackling nonlinear mapping problems, the proposed approach only activates a part of RIS elements and utilizes the corresponding cascaded channel estimate to predict another part. Through a synthetic deep neural network (DNN), the direct channel and active cascaded channel are first estimated sequentially, followed by the channel prediction for the inactive RIS elements. A three-stage training strategy is dev…
In this report, we summarize the end-to-end signal-to-noise ratio and the rate of half-duplex, full-duplex, amplify-and-forward, and decode-and-forward relay-aided communications, and well as the signal-to-noise ratio and the rate of the emerging technology known as reconfigurable intelligent surfaces.
This paper proposes a novel relay-aided intelligent reconfigurable surface (IRS) architecture for future wireless communication systems. The proposed architecture, which consists of two side-by-side intelligent surfaces connected via a full-duplex relay, has the potential of achieving the promising gains of intelligent surfaces while requiring much smaller numbers of reflecting elements. Consequently, the proposed IRS architecture needs significantly less channel estimation and beam training overhead and provides higher robustness compared to classical IRS approaches. Further, thanks to dividi…
In this paper, we analyze the error probability of reconfigurable intelligent surfaces (RIS)-enabled communication systems with quantized channel phase compensation over Rayleigh fading channels. The probability density and characteristic functions of the received signal amplitude are derive dand used to compute exact expressions for the bit error rate(BER). The resulting expressions are general, as they hold for an arbitrary number of reflecting elements N, and quantization levels, L. We introduce an exact asymptotic analysis in the high signal-to-noise ratio (SNR) regime, from which we demon…
We investigate a reconfigurable intelligent surface (RIS)-aided multi-user massive multiple-input multi-output (MIMO) system where low-resolution digital-analog converters (DACs) are configured at the base station (BS) in order to reduce the cost and power consumption. An approximate analytical expression for the downlink achievable rate is derived based on maximum ratio transmission (MRT) and additive quantization noise model (AQNM), and the rate maximization problem is solved by particle swarm optimization (PSO) method under both continuous phase shifts (CPSs) and discrete phase shifts (DPSs…
We investigate a multi-user multiple-input multiple-output interference network in the presence of multiple reconfigurable intelligent surfaces (RISs). The entire system is described by using a circuit-based model for the transmitters, receivers, and RISs. This is obtained by leveraging the electromagnetic tool of mutual impedances, which accounts for the signal propagation and the mutual coupling among closely-spaced scattering elements. An iterative and provably convergent optimization algorithm that maximizes the sum-rate of RIS-assisted multi-user interference channels is introduced. Numer…
Cooperative rate splitting (CRS), built upon rate splitting multiple access (RSMA) and opportunistic user relaying, has been recognized as a promising transmission strategy to enhance the user fairness and spectral efficiency in multiantenna broadcast channels. To further boost its performance, the interplay of CRS and reconfigurable intelligent surface (RIS) is investigated in this work. Specifically, a novel RIS-aided CRS transmission framework is proposed and the corresponding resource allocation problem to maximize the minimum rate among users is investigated. An alternative optimization a…
In this paper, we investigate the physical layer security in the reconfigurable intelligent surface (RIS)-aided cell-free networks. A maximum weighted sum secrecy rate problem is formulated by jointly optimizing the active beamforming (BF) at the base stations and passive BF at the RISs. To handle this non-trivial problem, we adopt the alternating optimization to decouple the original problem into two sub-ones, which are solved using the semidefinite relaxation and continuous convex approximation theory. To decrease the complexity for obtaining overall channel state information (CSI), we exten…
The performance of cooperative ambient backscatter communications (CABC) can be enhanced by employing reconfigurable intelligent surface (RIS) to assist backscatter transmitters. Since the RIS power consumption is a non-negligible issue, we consider a RIS assisted CABC system where the RIS with energy harvesting circuit can not only reflect signal but also harvest wireless energy. We study a transmission design problem to minimize the RIS power consumption with the quality of service constraints for both active and backscatter transmissions. The optimization problem is a mixed-integer non-conv…
This article focuses on the exploitation of reconfigurable intelligent surfaces (RISs) in multi-user networks employing orthogonal multiple access (OMA) or non-orthogonal multiple access (NOMA), with an emphasis on investigating the interplay between NOMA and RIS. Depending on whether the RIS reflection coefficients can be adjusted only once or multiple times during one transmission, we distinguish between static and dynamic RIS configurations. In particular, the capacity region of RIS aided single-antenna NOMA networks is characterized and compared with the OMA rate region from an information…
This letter considers the secure communication in a reconfigurable intelligent surface (RIS) aided full duplex (FD) system. An FD base station (BS) serves an uplink (UL) user and a downlink (DL) user simultaneously over the same time-frequency dimension assisted by a RIS in the presence of an eavesdropper. In addition, the artificial noise (AN) is also applied to interfere the eavesdropper's channel. We aim to maximize the sum secrecy rate of UL and DL users by jointly optimizing the transmit beamforming, receive beamforming and AN covariance matrix at the BS, and passive beamforming at the RI…
Reconfigurable intelligent surfaces (RISs) have attracted increasing interest due to their ability to improve the coverage, reliability, and energy efficiency of millimeter wave (mmWave) communication systems. However, designing the RIS beamforming typically requires large channel estimation or beam training overhead, which degrades the efficiency of these systems. In this paper, we propose to equip the RIS surfaces with visual sensors (cameras) that obtain sensing information about the surroundings and user/basestation locations, guide the RIS beam selection, and reduce the beam training over…
This letter is the third part of a three-part tutorial that focuses on rate-splitting multiple access (RSMA) for 6G. As Part III of the tutorial, this letter provides an overview of integrating RSMA and reconfigurable intelligent surface (RIS). We first introduce two potential PHY layer techniques, namely, RSMA and RIS, including the need for integrating RSMA with RIS and how they could help each other. Next, we provide a general model of an RIS-aided RSMA system and summarize some key performance metrics. Then, we discuss the major advantages of RIS-aided RSMA networks, and illustrate the rat…
Cell-free systems can effectively eliminate the inter-cell interference by enabling multiple base stations (BSs) to cooperatively serve users without cell boundaries at the expense of high costs of hardware and power sources due to the large-scale deployment of BSs. To tackle this issue, the low-cost reconfigurable intelligent surface (RIS) can serve as a promising technique to improve the energy efficiency of cell-free systems. In this paper, we consider an RIS aided cell-free MIMO system where multiple RISs are deployed around BSs and users to create favorable propagation conditions via reco…
A reconfigurable intelligent surface (RIS) enhanced non-orthogonal multiple access assisted backscatter communication (RIS-NOMABC) system is considered. A joint optimization problem over power reflection coefficients and phase shifts is formulated. To solve this non-convex problem, a low complexity algorithm is proposed by invoking the alternative optimization, successive convex approximation and manifold optimization algorithms. Numerical results corroborate that the proposed RIS-NOMABC system outperforms the conventional non-orthogonal multiple access assisted backscatter communication (NOMA…
This paper investigates the maximal achievable rate for a given average error probability and blocklength for the reconfigurable intelligent surface (RIS) assisted multiple-input and multiple-output (MIMO) system. The result consists of a finite blocklength channel coding achievability bound and a converse bound based on the Berry-Esseen theorem, the Mellin transform and the mutual information. Numerical evaluation shows fast speed of convergence to the maximal achievable rate as the blocklength increases and also proves that the channel variance is a sound measurement of the backoff from the …
Reconfigurable intelligent surface (RIS)-based transmission technology offers a promising solution to enhance wireless communication performance cost-effectively through properly adjusting the parameters of a large number of passive reflecting elements. This letter proposes a cosine similarity theorem-based low-complexity algorithm for adapting the phase shifts of an RIS that assists a multiple-input multiple-output (MIMO) transmission system. A semi-analytical probabilistic approach is developed to derive the theoretical average bit error probability (ABEP) of the system. Furthermore, the val…
Channel Estimation for Reconfigurable Intelligent Surface-Aided Multiuser Communication Systems Exploiting Statistical CSI of Correlated RIS-User Channels
In this work, we consider a single input single output (SISO) system for Reconfigurable Intelligent Surface (RIS) assisted mmWave communication. We consider Rician channel models over user node to RIS and RIS to Access Point (AP). We obtain closed form expressions for capacity with channel state information (CSI) and without CSI at the transmitter. Newly derived capacity expressions are closed form expressions in a very compact form. We also simplified the closed form expressions for average symbol error probability. We also characterize the impacts of key parameters Rician factor K and number…
We propose a novel reconfigurable intelligent surface (RIS) encoded information transmission scheme for a line-of-sight environment. A RIS fed with data modulates the information on impinging waves emitted from an external source in the states of polarization (SoP) of the scattered waves by performing a novel differential polarization shift keying. In particular, the information is encoded in the change of the SoP over two successive scattering slots. The proposed scheme is immune to the SoP fluctuations in the wireless channel which allows for non-coherent detection at the receiver.
New reconfigurable intelligent surface (RIS) based amplitude and phase modulation schemes are proposed as an evolution how the phase-only modulation schemes available in the literature. Explicitly, both the amplitude-phase shift keying (A-PSK) and quadrature amplitude-phase shift keying (QA-PSK) are conceived, where the RIS is assumed to be part of a transmitter to deliver information to the multi-antenna aided downlink receiver. In the proposed design, the RIS is partitioned into multiple blocks, and the information bits are conveyed by controlling both the ON-OFF state and the phase shift of…
What is a reconfigurable intelligent surface? What is a smart radio environment? What is a metasurface? How do metasurfaces work and how to model them? How to reconcile the mathematical theories of communication and electromagnetism? What are the most suitable uses and applications of reconfigurable intelligent surfaces in wireless networks? What are the most promising smart radio environments for wireless applications? What is the current state of research? What are the most important and challenging research issues to tackle? These are a few of the many questions that we investigate in this …
This paper exploits the potential of reconfigurable intelligent surface (RIS) to improve radar sensing in a non-orthogonal multiple access (NOMA) empowered integrated sensing and communication (NOMA-ISAC) network. The objective is to maximize the minimum radar beampattern gain by jointly optimizing the active beamforming, power allocation coefficients and passive beamforming. To tackle the formulated non-convex problem, we propose an efficient joint optimization algorithm by invoking alternating optimization, successive convex approximation (SCA) and sequential rank-one constraint relaxation (…
