The upcoming PANDA experiment at FAIR will be among a new generation of particle physics experiments to employ a novel event filtering system realised purely in software, i.e. a software trigger. To educate its triggering decisions, online reconstruction algorithms need to offer outstanding performance in terms of efficiency and track quality. We present a method to reconstruct longitudinal track parameters in PANDA's Straw Tube Tracker, which is general enough to be easily added to other track finding algorithms that focus on transversal reconstruction. For the pattern recognition part of this method, three approaches are employed and compared: A combinatorial path finding approach, a Hough transformation, and a recursive annealing fit. In a systematic comparison, the recursive annealing fit was found to outperform the other approaches in every category of quality parameters and reaches a reconstruction efficacy of 95% and higher.
We report on a novel concept of silicon microstrips and straw tubes detector, where integration is accomplished by a straw module with straws not subjected to mechanical tension in a Rohacell lattice and carbon fiber reinforced plastic shell. Results on mechanical and test beam performances are reported on as well.
The coordinate detectors based on straw tubes provide a high accuracy of the radial coordinate measurement using the drift time and a small amount of matter in the way of the measured particles. However, the measurement of the coordinate along the wire constitutes a problem. This paper proposes a method for measuring the hit coordinate along the wire with an accuracy better than 1 mm in a straw tube detector using the signals from the cathodes of the detector.
We report on a novel concept of silicon microstrips and straw tubes detector, where integration is accomplished by a straw module with straws not subjected to mechanical tension in a Rohacell $^{\circledR}$ lattice and carbon fiber reinforced plastic shell. Results on mechanical and test beam performances are reported on as well.
A check of the eccentricity of the aluminised kapton straw tubes used in the BTeV experiment is accomplished using X-ray tomography of the section of tubes modules. 2 and 3-dimensional images of the single tubes and of the modules are reconstructed and analysed. Preliminary results show that a precision better than 40 $μ$m can be reached on the measurement of the straw radii.
A novel FPGA based online tracking algorithm for helix track reconstruction in a solenoidal field, developed for the PANDA spectrometer, is described. Employing the Straw Tube Tracker detector with 4636 straw tubes, the algorithm includes a complex track finder, and a track fitter. Implemented in VHDL, the algorithm is tested on a Xilinx Virtex-4 FX60 FPGA chip with different types of events, at different event rates. A processing time of 7 $μ$s per event for an average of 6 charged tracks is obtained. The momentum resolution is about 3\% (4\%) for $p_t$ ($p_z$) at 1 GeV/c. Comparing to the al…
The PANDA experiment will be built at the FAIR facility at Darmstadt (Germany) to perform accurate tests of the strong interaction through bar pp and bar pA annihilation's studies. To track charged particles, two systems consisting of a set of planar, closed-packed, self-supporting straw tube layers are under construction. The PANDA straw tubes will have also unique characteristics in term of material budget and performance. They consist of very thin mylar-aluminized cathodes which are made self-supporting by means of the operation gas-mixture over-pressure. This solution allows to reduce at m…
For the development of charged particle detectors based on straw tubes operating in vacuum, a special measurement technique is required for the evaluation of their mechanical properties. A summary of the known equations that govern straw behavior under internal pressure is provided, and a new experimental method of a strained pressurized straw tube study is presented in this paper. The Poisson's ratio of the straw wall, which defines the stability conditions of a built-in tube, is measured for the NA62 spectrometer straw, and its minimum pre-tension is estimated.
Prototypes of newly developed boron-coated straw (BCS) detectors have been tested in the thermal and cold neutron energy ranges. Their neutron detection performance has been benchmarked against the industry standard (detector tubes filled with 3He gas). The tests show that the BCS straws perform near their theoretical limit regarding the detection efficiency, which is adequate for scientific instruments in the cold neutron energy range. The BCS detectors perform on par with 3He tubes in terms of signal to noise and timing resolution, and superior regarding longitudinal spatial resolution.
Straw tube detectors are single wire proportional counters that are widely used as a tracking device. We have carried out R$\&$D with a straw tube detector prototype. The motivation of this work is to study the stability of the performance in terms of gain and energy resolution of the straw tube detectors under high rate radiation. Two different methods are incorporated to perform this study. The gain and energy resolution of the detector are studied along with its variation with ambient temperature and pressure. X-ray from a radioactive source is used to irradiate the detector and the same so…
The article considers a prototype module with sensitive dimensions of 2 x 0.5 m2 based on 2 m long straw tubes which preserves its geometrical dimensions up to the pressure of 4 bar independently of the ambient temperature and humidity. The suggested technique provides a possibility of constructing relatively low-cost planar modules by using straw tubes as long as needed for constructing large area detectors at colliders or other field experiments by assembling them in a common coordinate detector with a user-specified acceptance. The distinguishing feature of a detector is its good radiation …
Basic R & D have been carried out with one small straw tube detector prototype with premixed gas of Ar+CO2 in 70:30 and 90:10 ratio. The gain and the energy resolution are measured with Fe55 X-ray source. Effect of temperature and pressure on these parameters are measured. The variation of gain and energy resolution with rate per unit length are also measured. The details of the test set-up, the method of measurement and the test results are presented in this paper.
York College, City University of New York（纽约市立大学约克学院）；Boston University（波士顿大学）；Fermi National Accelerator Laboratory（费米国家加速器实验室）；FPT University（FPT大学）；Yale University（耶鲁大学）；University of Minnesota（明尼苏达大学）
Performance Evaluation of Straw Tubes with Muon Beams at CERN
University of Michigan（密歇根大学）；Tufts University（塔夫茨大学）；Institute of Nuclear Physics, Almaty（阿拉木图核物理研究所）；Joint Institute for Nuclear Research, Dubna（杜布纳联合核研究所）；University of Florida（佛罗里达大学）；CERN（欧洲核子研究组织）；NRC Kurchatov Institute PNPI（库尔恰托夫国家研究中心普列哈诺夫物理技术研究所）
We have developed the baseline design for the straw drift tube tracking detectors for high rate environment application. The low-mass inner straw elements and the technology of the multianode straws assembly was devised and checked. The prototype chamber was constructed and studied the granularity of similar chambers can be reduced to one cm2. Submitted to Physics of Elementary Particles and Atomic Nuclei, Letters
The Mu2e experiment will search for coherent, neutrino-less conversion of muons into electrons in the Coulomb field of an aluminum nucleus with a sensitivity of four orders of magnitude better than previous experiments. The signature of this process is an electron with energy nearly equal to the muon mass. Mu2e relies on a precision (0.1%) measurement of the outgoing electron momentum to separate signal from background. In order to achieve this goal, Mu2e has chosen a very low-mass straw tracker, made of 20,736 5 mm diameter thin-walled (15 $μ$m) Mylar straws, held under tension to avoid the n…
Detector rate capability is one of the main parameters for designing a new detector for high energy physics due to permanent rise of the beam luminosity of modern accelerators. One of the widely used detectors for particle track reconstruction is a straw detector based on drift tubes. The rate capability of such detectors is limited by the parameters of readout electronics. The traditional method of increasing detector rate capability is increasing their granularity (a number of readout channels) by reducing the straw diameter and/or by dividing the straw anode wire into two parts (for decreas…
The PANDA (anti-Proton ANnihilation at DArmstadt) experiment at the Facility for Anti-proton and Ion Research is going to study strong interactions at the scale at which quarks are confined to form hadrons. A continuous beam of antiproton, provided by the High Energy Storage Ring (HESR), will impinge on a fixed hydrogen target. The antiproton beam momentum spans from 1.5 GeV {Natural units, c=1} to 15 GeV \cite{physics2009report}, will create optimal conditions for studying many different aspects of hadron physics, including hyperon physics. Precision physics studies require a highly efficient…
This article presents the results of a study of the longitudinal spatial resolution of 2 m long straw tubes by means of the direct timing method (DTM). The feasibility of achieving a coordinate resolution (r.m.s.) better than 2 cm over full length of the straw is demonstrated. The spatial resolution insignificantly changes when measured by detecting gammas from a Fe-55 gamma ray source or minimum ionizing particles from a Ru-106 source. The use of the same type of FEE for data taking both for measuring the drift time of ionization electrons and propagation of a signal along the anode wire allo…
Multiple types of high quality neutron detectors are proposed for the first phase of the China Spallation Neutron Source (CSNS), which will be commissioned in 2018. Considering the shortage of 3He supply, a detector module composed of 49 boron-coated straws (BCS) was developed by Proportional Technologies Inc. (PTI). Each straw has a length of 1000 mm and a diameter of 7.5 mm. Seven straws are tightly packed in a tube, and seven tubes are organized in a row to form a detector module. The charge division method is used for longitudinal positioning. A specific readout system was utilized to outp…
The considering different technics of measuring the longitudinal coordinates by the drift tubes. It is shown that the determination of the longitudinal coordinate by the direct time method provides the best longitudinal resolution. The realization of this method enables the development of coordinate detectors based on the straw with two-dimensional readout, which can be fast enough and not very complex.
Many complex vacuum systems include edge-welded bellows. Their simulation in the molecular flow regime with a Test Particle Monte Carlo (TPMC) code, such as MolFlow+, can take considerable amounts of computing power and time. Therefore we investigated the change of the transmission probability of a bellow compared to a cylindrical tube in TPMC simulations. The results were used to develop an empirical model to simplify the geometry of a bellow in a TPMC model by replacing it with a cylindrical tube of extended length, consequently compensating the reduced conductance of the bellow. The simulat…
The LHCb Outer Tracker is a gaseous detector covering an area of 5x6 m2 with 12 double layers of straw tubes. The detector with its services are described together with the commissioning and calibration procedures. Based on data of the first LHC running period from 2010 to 2012, the performance of the readout electronics and the single hit resolution and efficiency are presented. The efficiency to detect a hit in the central half of the straw is estimated to be 99.2%, and the position resolution is determined to be approximately 200 um. The Outer Tracker received a dose in the hottest region c…
The Central Drift Chamber is a straw-tube wire chamber of cylindrical structure located surrounding the target inside the bore of the GlueX spectrometer solenoid. Its purpose is to detect and track charged particles with momenta as low as 0.25 GeV/c as well as to identify low-momentum protons via energy loss. The construction of the detector is described and its operation and calibration are discussed in detail. The design goal of 150 microns in position resolution has been reached.
The ATLAS detector at CERN's Large Hadron Collider (LHC) is equipped with a tracking system at its core (the Inner Detector, ID) consisting of silicon and gaseous straw tube detectors. The physics performance of the ID requires a precision alignment; a challenge involving complex algorithms and significant computing power. The alignment algorithms were already validated on: Combined Test Beam data, Cosmic Ray runs and simulated physics events. The alignment chain was tested on a daily basis in exercises that mimicked ATLAS data taking operations. ID commissioning after final installation into …
