The ATLAS detector at CERN's Large Hadron Collider (LHC) is equipped with a tracking system at its core (the Inner Detector, ID) consisting of silicon and gaseous straw tube detectors. The physics performance of the ID requires a precision alignment; a challenge involving complex algorithms and significant computing power. The alignment algorithms were already validated on: Combined Test Beam data, Cosmic Ray runs and simulated physics events. The alignment chain was tested on a daily basis in exercises that mimicked ATLAS data taking operations. ID commissioning after final installation into the ATLAS detector has yielded thousands of reconstructed cosmic ray tracks, which have been used for an initial alignment of the ID before the LHC start-up. A hardware system using Frequency Scanning Interferometry will be used to monitor structural deformations. Given the programme outlined here, the ATLAS Inner Detector has had a solid preparation for LHC collisions.
The inner detector is the central tracking device of the ATLAS detector. In these proceedings the tracking performance of the inner detector is presented on collision data recorded at $\sqrt{s}$ = 900 GeV and 7 TeV. The identification of resonances like $Ξ$ and $Ω$ baryons in cascade decays via $K_{\mathrm{s}}$ and $Λ$ mesons is presented as well as the reconstruction of the $J / ψ$ and $ψ$(2S) mesons decaying into two muons. Furthermore, the performance of the track reconstruction and a data-driven method of estimating the track reconstruction efficiency as used in measurements of charged par…
The ATLAS Inner Detector is responsible for particle tracking in ATLAS experiment at CERN Large Hadron Collider (LHC) and comprises silicon and gas based detectors. The combination of both silicon and gas based detectors provides high precision impact parameter and momentum measurement of charged particles, with high efficiency and small fake rate. The ID has been used to exploit fully the physics potential of the LHC since the first proton-proton collisions at 7 TeV were delivered in 2009. The performance of track and vertex reconstruction is presented, as well as the operation aspects of the…
The magnetic field integrals connected with the momentum resolution are calculated for the ATLAS inner tracking volume in a range of pseudorapidity $|η| < 3$ for the cases of `ideal' and inhomogeneous solenoid fields. In the latest case, the magnetic field map is extracted from POISSON calculations with help of an interface program POISGT. The tracking volume is restricted by a length of 6.8 m and by a radius of 1.06 m. The solenoid coil with an active length of 6.3 m and with an inner radius of 1.23 m produces the magnetic flux density of 2 T in the center of the coil.
The ATLAS detector, built at one of the interaction points of the Large Hadron Collider, is operational and has been collecting data from cosmic rays. This paper describes the track based alignment of the ATLAS Inner Detector tracker which was performed using cosmic rays collected in 2008. The alignment algorithms are described and the performance of the alignment is demonstrated by showing the resulting hit residuals and comparing track parameters of upper and lower segments of tracks. The impact of the alignment on physics measurements is discussed.
Particle physicists at the Large Hadron Collider investigate the properties of matter at subatomic length scales by colliding together bunches of high-energy protons and observing the decay products of the collisions. ATLAS is one of two general-purpose detectors that reconstruct the interactions and, as part of a wide range of physics goals, measure the production of Higgs bosons and searches for exotic new phenomena including supersymmetry, extra dimensions of spacetime, and dark matter. Selecting the interesting collision events using hardware- and software-based triggers is a major challen…
The upgrade to the ATLAS trigger for LHC Run 2 is presented including a description of the design and performance of the newly reimplemented tracking algorithms. The profiling infrastructure, constructed to provide prompt feedback from the optimisation procedure is described including the methods used to monitor the relative performance improvements as the code evolves. The performance of the trigger on the first data collected in the LHC Run 2 is presented.
Several algorithms for tracking and for primary and secondary vertex reconstruction have been developed by the ATLAS collaboration following different approaches. This has allowed a thorough cross-check of the performances of the algorithms and of the reconstruction software. The results of the most recent studies on this topic are discussed and compared.
Physics collisions at 13 TeV are expected at the LHC with an average of 40-50 proton-proton collisions per bunch crossing under nominal conditions. Tracking at trigger level is an essential tool to control the rate in high-pileup conditions while maintaining a good efficiency for relevant physics processes. The Fast TracKer is an integral part of the trigger upgrade for the ATLAS detector. For every event passing the Level-1 trigger (at a maximum rate of 100 kHz) the FTK receives data from all the channels of the silicon detectors, providing tracking information to the High Level Trigger in or…
The Phase-II upgrade of the ATLAS detector for the High Luminosity Large Hadron Collider (HL-LHC) includes the replacement of the current Inner Detector with an all-silicon tracker consisting of pixel and strip detectors. The current Phase-II detector layout requires the construction of 20,000 strip detector modules consisting of sensor, circuit boards and readout chips, which are connected mechanically using adhesives. The adhesive between readout chips and circuit board is a silver epoxy glue as was used in the current ATLAS SemiConductor Tracker (SCT). This glue has several disadvantages, w…
The LHC Phase-II upgrade will lead to a significant increase in luminosity, which in turn will bring new challenges for the operation of inner tracking detectors. A possible solution is to use active silicon sensors, taking advantage of commercial CMOS technologies. Currently ATLAS R&D programme is qualifying a few commercial technologies in terms of suitability for this task. In this paper a prototype designed in one of them (LFoundry 150 nm process) will be discussed. The chip architecture will be described, including different pixel types incorporated into the design, followed by simulation…
The goals of the ongoing and planned ATLAS muon detector upgrades are to increase the acceptance for precision muon momentum measurement and triggering and to improve the rate capability of the muon chambers in the high-background regions corresponding to the increasing LHC luminosity. Smalldiameter Muon Drift Tube (sMDT) chambers have been developed for these purposes. With half the drift-tube diameter of the current ATLAS Muon Drift Tube (MDT) chambers with 30 mm drift tube diameter and otherwise unchanged operating parameters, the sMDT chambers share all the advantages of the MDTs, but have…
The alignment of tracking detectors is crucial for the physics programme at the LHC, especially for precision measurements like the W mass. The alignment of the ATLAS silicon tracking detectors with a total of 5832 modules poses an unprecedented challenge. In this poster, two track-based alignment algorithms at ATLAS will be covered: the Global chi^2 Algorithm based on chi^2 minimisation, and the Robust Alignment Algorithm based on centering residual distributions. On a time scale of minutes and hours, the geometry of the silicon tracking detectors can be monitored with the Frequency Scanning …
ATLAS is a multipurpose experiment at the LHC. The tracking system of ATLAS, embedded in a 2 T solenoidal field, is composed of different technologies: silicon planar sensors (pixel and microstrips) and drift-tubes. The procedure used to align the ATLAS tracker and the results of the alignment using data recorded during 2010 and 2011 using LHC proton-proton collision runs at 7 TeV are presented. Validation of the alignment is performed by measuring the alignment observables as well as many other physics observables, notably resonance invariant masses in a wide mass range. The E/p distributions…
This work presents a depleted monolithic active pixel sensor (DMAPS) prototype manufactured in the LFoundry 150 nm CMOS process. The described device, named LF-Monopix, was designed as a proof of concept of a fully monolithic sensor capable of operating in the environment of outer layers of the ATLAS Inner Tracker upgrade for the High Luminosity Large Hadron Collider (HL-LHC). Implementing such a device in the detector module will result in a lower production cost and lower material budget compared to the presently used hybrid designs. In this paper the chip architecture will be described foll…
A new small-diameter Monitored Drift Tube (sMDT) chamber has been developed for the muon spectrometer of the ATLAS experiment to handle the higher collision rates expected at the CERN High Luminosity Large Hadron Collider (HL-LHC). This paper presents measurements of the tracking resolution and hit efficiency of two prototype sMDT chambers constructed at the University of Michigan. Using cosmic-ray muons the sMDT tracking resolution of 103.7$\pm8.1$ \textmu m was measured for one chamber and 101.8$\pm$7.8 \textmu m for the other, compared with a design resolution of 106 \textmu m. A further tr…
The ATLAS muon spectrometer is designed to measure muon momenta with a resolution of 4% @ 100 GeV/c rising to 10% @ 1 TeV/c track momentum. The spectrometer consists of precision tracking and trigger chambers embedded in a 2T magnetic field generated by three large air-core superconducting toroids. The precision detectors provide 50 micron tracking resolution to a pseudo-rapidity of 2.7. The system also includes an optical monitoring system which measures detector positions with 40 micron precision. This paper reports on the calibration and performance of the ATLAS muon spectrometer.
The ATLAS Inner Detector is a composite tracking system consisting of silicon pixels, silicon strips and straw tubes in a 2 T magnetic field. Its installation was completed in August 2008 and the detector took part in data- taking with single LHC beams and cosmic rays. The initial detector operation, hardware commissioning and in-situ calibrations are described. Tracking performance has been measured with 7.6 million cosmic-ray events, collected using a tracking trigger and reconstructed with modular pattern-recognition and fitting software. The intrinsic hit efficiency and tracking trigger ef…
Impact of Cold Noise on the tracking performance of ATLAS ITk short strip barrel modules using a charged particle beam
Santa Cruz Institute for Particle Physics, University of California Santa Cruz（加州大学圣克鲁兹分校圣克鲁兹粒子物理研究所）；Deutsches Elektronen-Synchrotron DESY（德国电子同步加速器中心）；Lunds universitet（隆德大学）；University of Birmingham（伯明翰大学）；Charles University（查理大学）；Rutherford Appleton Laboratory（卢瑟福阿普尔顿实验室）；University of British Columbia（不列颠哥伦比亚大学）；TRIUMF（特里姆夫实验室）
ATLAS is one of the two general purpose detectors at the world's largest particle accelerator, the Large Hadron Collider (LHC). The LHC will be colliding proton beams at a center of mass energy {\surd}s= 14 TeV and is currently operating at {\surd}s = 7 TeV. During the commissioning phase since September 2008, the ATLAS recorded cosmic-rays data and proton-proton collisions at {\surd}s = 0.9 TeV. This data has extensively been used for the alignment and calibration of various sub-detectors. The ATLAS detector has a precision tracking system installed around the beam pipe for the measurements o…
Precision sound velocity measurements can simultaneously determine binary gas composition and flow. We have developed an analyzer with custom electronics, currently in use in the ATLAS inner detector, with numerous potential applications. The instrument has demonstrated ~0.3% mixture precision for C3F8/C2F6 mixtures and < 10-4 resolution for N2/C3F8 mixtures. Moderate and high flow versions of the instrument have demonstrated flow resolutions of +/- 2% F.S. for flows up to 250 l.min-1, and +/- 1.9% F.S. for linear flow velocities up to 15 ms-1; the latter flow approaching that expected in the …
The alignment of the ATLAS Inner Detector is performed with a track-based algorithm. The aim of the detector alignment is to provide an accurate description of the detector geometry such that track parameters are accurately determined and bias free. The detector alignment is validated and improved by studying resonant decays ($J/ψ$ and $Z$ to $μ^+μ^-$). The detailed study of these resonances (together with the properties of the tracks of their decay products) allows to detect and correct for alignment weak modes such as detector curls and radial deformations that may bias the momentum and/or t…
In next ten years, the Large Hadron Collider will be upgraded to the High Luminosity LHC (HL-LHC), resulting in ten time more integrated luminosity. To withstand the much harsher radiation and occupancy conditions of the HL-LHC, the inner tracker of the ATLAS detector must be redesigned and rebuilt completely. The design of the ATLAS Upgrade inner tracker (ITk) has already been defined. It consists of several layers of silicon particle detectors. The innermost layers will be composed of silicon pixel sensors, and the outer layers will consist of silicon microstrip sensors. This paper will focu…
The ATLAS Collaboration will upgrade its semiconductor pixel tracking detector with a new Insertable B-layer (IBL) between the existing pixel detector and the vacuum pipe of the Large Hadron Collider. The extreme operating conditions at this location have necessitated the development of new radiation hard pixel sensor technologies and a new front-end readout chip, called the FE-I4. Planar pixel sensors and 3D pixel sensors have been investigated to equip this new pixel layer, and prototype modules using the FE-I4A have been fabricated and characterized using 120 GeV pions at the CERN SPS and 4…
The recent R&D focus on CMOS sensors with charge collection in a depleted zone has opened new perspectives for CMOS sensors as fast and radiation hard pixel devices. These sensors, labelled as depleted CMOS sensors (DMAPS), have already shown promising performance as feasible candidates for the ATLAS Inner Tracker (ITk) upgrade, possibly replacing the current passive sensors. A further step to exploit the potential of DMAPS is to investigate the suitability of equipping the outer layers of the ATLAS ITk upgrade with fully monolithic CMOS sensors. This paper presents the development of a deplet…
In view of the high luminosity phase of the LHC (HL-LHC) to start operation around 2026, a major upgrade of the tracker system for the ATLAS experiment is in preparation. The expected neutron equivalent fluence of up to 2.4 * 1e16 1 MeV neq./cm2 at the innermost layer of the pixel detector poses the most severe challenge. Thanks to their low material budget and high charge collection efficiency after irradiation, modules made of thin planar pixel sensors are promising candidates to instrument these layers. To optimise the sensor layout for the decreased pixel cell size of 50 * 50 μm2, TCAD dev…
Run-2 of the Large Hadron Collider (LHC) will provide new challenges to track and vertex reconstruction with higher energies, denser jets and higher rates. Therefore the ATLAS experiment has constructed the first 4-layer Pixel Detector in HEP, installing a new pixel layer, also called Insertable B-Layer (IBL). The IBL is a fourth layer of pixel detectors, and has been installed in May 2014 at a radius of 3.3 cm between the existing Pixel Detector and a new smaller radius beam-pipe. The new detector, built to cope with the high radiation and expected occupancy, is the first large scale applicat…
The ATLAS experiment will undergo a major upgrade of the tracker system in view of the high luminosity phase of the LHC (HL-LHC) to start operation in 2026. The most severe challenges are to be faced by the innermost layers of the pixel detector which will have to withstand a radiation fluence of up to $1.4\times10^{16}\,$n$_\text{eq}$/cm$^{2}$. Thin planar pixel modules are promising candidates to instrument these layers, thanks to the small material budget and their high charge collection efficiency after irradiation. Sensors of $100-200\,μ$m thickness, interconnected to FE-I4 read-out chips…
The steadily increasing luminosity of the LHC requires an upgrade with high-rate and high-resolution detector technology for the inner end cap of the ATLAS muon spectrometer: the New Small Wheels (NSW). In order to achieve the goal of precision tracking at a hit rate of about 15 kHz/cm$^2$ at the inner radius of the NSW, large area Micromegas quadruplets with 100\,\microns spatial resolution per plane have been produced. % IRFU, from the CEA research center of Saclay, is responsible for the production and validation of LM1 Micromegas modules. The construction, production, qualification and val…
Hardware-based track reconstruction in the CMS and ATLAS trigger systems for the High-Luminosity LHC upgrade will provide unique capabilities. An overview is presented of earlier track trigger systems at hadron colliders, in particular for the Tevatron CDF and D0 experiments. We discuss the plans of the CMS and ATLAS experiments to implement hardware-based track reconstruction for the High-Luminosity LHC. Particular focus is placed on the track trigger capability of the upgraded CMS experiment. We discuss the challenges and opportunities of this novel handle, and review the alternatives that w…
For the High Luminosity upgrade of the Large Hadron Collider the current ATLAS Inner Detector will be replaced by an all-silicon Inner Tracker. The pixel detector will consist of five barrel layers and a number of rings, resulting in about 13 m^2 of instrumented area. Due to the huge non-ionising fluence (1e16 neq/cm^2) and ionising dose (5 MGy), the two innermost layers, instrumented with 3D pixel sensors and 100 um thin planar sensors, will be replaced after about five years of operation. Each pixel layer comprises hybrid detector modules that will be read out by novel ASICs, implemented in …
The structure of the CMS inner tracking system has been studied using nuclear interactions of hadrons striking its material. Data from proton-proton collisions at a center-of-mass energy of 13 TeV recorded in 2015 at the LHC are used to reconstruct millions of secondary vertices from these nuclear interactions. Precise positions of the beam pipe and the inner tracking system elements, such as the pixel detector support tube, and barrel pixel detector inner shield and support rails, are determined using these vertices. These measurements are important for detector simulations, detector upgrades…
The inner drift chamber of the BESIII is encountering serious aging problem after five year's running. For the first layer, the decrease in gas gain is about 26% from 2009 to 2013. The upgrade of the inner tracking detector has become an urgent problem for the BESIII experiment. An inner tracker using CMOS pixel sensors is an important candidate because of its great advantages on spatial resolution and radiation hardness. In order to carry out a Monte Carlo study on the expected performance, a Geant4-based full simulation for the silicon pixel detector has been implemented. The tracking method…
The ATLAS Pixel detector is a high-resolution, low-noise silicon-based device designed to provide tracking and vertexing information within a distance of 12 cm from the LHC beam axis. It consists of approximately 80 million pixel channels with radiation-hard front-end electronics connected through optical fibers to a custom-controlled DAQ system away from the detector. Following the successful installation of the detector in June 2007, an intense commissioning period was conducted in the year 2008 and more than 400,000 cosmic-ray tracks were recorded in conjunction with other ATLAS sub-detecto…
The ATLAS collaboration will replace its tracking detector with new all silicon pixel and strip systems. This will allow to cope with the higher radiation and occupancy levels expected after the 5-fold increase in the luminosity of the LHC accelerator complex (HL-LHC). In the new tracking detector (ITk) pixel modules with increased granularity will implement to maintain the occupancy with a higher track density. In addition, both sensors and read-out chips composing the hybrid modules will be produced employing more radiation hard technologies with respect to the present pixel detector. Due to…
The upgrade to the High Luminosity Large Hadron Collider will pose unprecedented challenges to the tracking systems of all experiments. Recent advancement of active pixel detectors designed in CMOS processes provide attractive alternatives to the well-established hybrid design using passive sensors. This article presents studies with a high-voltage CMOS active pixel sensor designed for the ATLAS tracker upgrade. The sensor is glued to the read-out chip of the Insertable B-Layer. The device under test is structured in smaller pixels than those of the attached read-out chip with information on t…
The Fast Tracker (FTK) is a proposed upgrade to the ATLAS trigger system that will operate at full Level-1 output rates and provide high quality tracks reconstructed over the entire detector by the start of processing in Level-2. FTK solves the combinatorial challenge inherent to tracking by exploiting the massive parallelism of Associative Memories (AM) that can compare inner detector hits to millions of pre-calculated patterns simultaneously. The tracking problem within matched patterns is further simplified by using pre-computed linearized fitting constants and leveraging fast DSP's in mode…
The ATLAS pixel detector is a high precision silicon tracking device located closest to the LHC interaction point. It belongs to the first generation of its kind in a hadron collider experiment. It will provide crucial pattern recognition information and will largely determine the ability of ATLAS to precisely track particle trajectories and find secondary vertices. It was the last detector to be installed in ATLAS in June 2007, has been fully connected and tested in-situ during spring and summer 2008. It is currently in a commissioning phase using cosmic-ray events. We present the highlights …
The ATLAS Roman Pot system is designed to determine the total proton-proton cross-section as well as the luminosity at the Large Hadron Collider (LHC) by measuring elastic proton scattering at very small angles. The system is made of four Roman Pot stations, located in the LHC tunnel in a distance of about 240~m at both sides of the ATLAS interaction point. Each station is equipped with tracking detectors, inserted in Roman Pots which approach the LHC beams vertically. The tracking detectors consist of multi-layer scintillating fibre structures readout by Multi-Anode-Photo-Multipliers.
Small-diameter muon drift tube (sMDT) chambers with 15 mm tube diameter are a cost-effective technology for high-precision muon tracking over large areas at high background rates as expected at future high-energy hadron colliders including HL-LHC. The chamber design and construction procedures have been optimized for mass production and provide sense wire positioning accuracy of better than 10 ?m. The rate capability of the sMDT chambers has been extensively tested at the CERN Gamma Irradiation Facility. It exceeds the one of the ATLAS muon drift tube (MDT) chambers, which are operated at unpr…
During the Long Shutdown 2 of the LHC in 2018/2019, the ALICE experiment plans the installation of a novel Inner Tracking System. It will replace the current six layer detector system with a seven layer detector using Monolithic Active Pixel Sensors. The upgraded Inner Tracking System will have significantly improved tracking and vertexing capabilities, as well as readout rate to cope with the expected increased Pb-Pb luminosity of the LHC. The choice of Monolithic Active Pixel Sensors has been driven by the specific requirements of ALICE as a heavy ion experiment dealing with rare processes a…
This work presents a new silicon vertical JFET (V-JFET) device, based on the trenched 3D-detector technology developed at IMB-CNM, to be used as switches for the High-Voltage powering scheme of the ATLAS upgrade Inner Tracker. The optimization of the device characteristics is performed by 2D and 3D TCAD simulations. Special attention has been paid to the on-resistance and the switch-off and breakdown voltages to meet the specific requirements of the system. In addition, a set of parameter values has been extracted from the simulated curves to implement a SPICE model of the proposed V-JFET tran…
Depleted monolithic active pixel sensors (DMAPS), which exploit high voltage and/or high resistivity add-ons of modern CMOS technologies to achieve substantial depletion in the sensing volume, have proven to have high radiation tolerance towards the requirements of ATLAS in the high-luminosity LHC era. Depleted fully monolithic CMOS pixels with fast readout architectures are currently being developed as promising candidates for the outer pixel layers of the future ATLAS Inner Tracker, which will be installed during the phase II upgrade of ATLAS around year 2025. In this work, two DMAPS prototy…
FASER (ForwArd Search ExpeRiment) fills the axial blindspot of other, radially arranged LHC experiments. It is installed 480 meters from the ATLAS interaction point, along the collision axis. FASER will search for new, long-lived particles that may be hidden in the collimated reaction products exiting ATLAS. The tracking detector is an essential component for observing LLP signals. FASER's tracking stations use silicon microstrip detectors to measure the path of charged particles.This is a summary of one of FASER's latest papers "The tracking detector of the FASER experiment", which describes …
We describe the main components of the ATLAS Forward Physics project, namely the movable beam pipe, the tracking and timing detectors which allow to detect intact protons in the final state at the LHC. The position detector is composed on 6 layers of 3D silicon detectors readout by FE-I4 chips developped for ATLAS. The fast timing detector is built from a quartz-based Cerenkov detector coupled to a microchannel plate photomultiplier tube, followed by the electronic elements that amplify, measure, and record the time of the event along with a stabilized reference clock signal, ensuring a time r…
The ATLAS detector is currently being upgraded with a new layer of pixel based charged particle tracking and a new arrangement of the services for the pixel detector. These upgrades require the replacement of the opto-boards previously used by the pixel detector. In this report we give details on the design and production of the new opto-boards.
The challenging demands of the ATLAS High Luminosity (HL-LHC) Upgrade aim for a complete swap of new generation sensors that should cope with the ultimate radiation hardness. FBK has been one of the prime foundries to develop and fabricate such radiation-hard 3D silicon (Si) sensors. These sensors are chosen to be deployed into the innermost layer of the ATLAS Inner Tracker (ITk). Recently, a pre-production batch of 3D Si sensors of 50x50 um2 pixel geometry, compatible with the full-size ITKPix (RD53B) readout chip, was fabricated. Two wafers holding temporary metal were diced at IZM, Germany,…
The ATLAS detector has to undergo significant updates at the end of the current decade, in order to withstand the increased occupancy and radiation damage that will be produced by the high-luminosity upgrade of the Large Hadron Collider. In this presentation we give an overview of the recent accomplishments of the R&D activity on the planar pixel sensors for the ATLAS Inner Detector upgrade.
For the muon spectrometer of the ATLAS detector at the large hadron collider (LHC), large drift chambers consisting of 6 to 8 layers of pressurized drift tubes are used for precision tracking covering an active area of 5000 m2 in the toroidal field of superconducting air core magnets. The chambers have to provide a spatial resolution of 41 microns with Ar:CO2 (93:7) gas mixture at an absolute pressure of 3 bar and gas gain of 2?104. The environment in which the chambers will be operated is characterized by high neutron and background with counting rates of up to 100 per square cm and second. T…
For the Phase-II Upgrade of the ATLAS detector at CERN, the current ATLAS Inner Detector will be replaced with the ATLAS Inner Tracker. The ATLAS Inner Tracker will be an all-silicon detector, consisting of a pixel tracker and a strip tracker. Sensors for the ITk strip tracker are required to have a low leakage current up to bias voltages of -700 V to maintain a low noise and power dissipation. In order to minimise sensor leakage currents, particularly in the high-radiation environment inside the ATLAS detector, sensors are foreseen to be operated at low temperatures and to be manufactured fro…
ATLAS is making extensive efforts towards preparing a detector upgrade for the high luminosity operations of the LHC (HL-LHC), which will commence operation in about 10 years. The current ATLAS Inner Detector will be replaced by an all-silicon tracker (comprising an inner Pixel tracker and outer Strip tracker). The software currently used for the new silicon tracker is broadly inherited from that used for the LHC Run-1 and Run-2, but many new developments have been made to better fulfill the future detector and operation requirements. One aspect in particular which will be highlighted is the s…
