Commissioning of the ATLAS Inner Tracking Detector

Commissioning ATLAS Trigger

The ATLAS experiment at the Large Hadron Collider (LHC) will face the challenge of efficiently selecting interesting candidate events in $pp$ collisions at 14 TeV centre-of-mass energy, whilst rejecting the enormous number of background events. Therefore it is equipped with a three level trigger system. The first level is is hardware based and uses coarse granularity calorimeter information and fast readout muon chambers. The second and third level triggers, which are software based, will need to reduce the first level trigger output rate of ~ 75 kHz to ~ 200 Hz written out to mass storage. Th…

Commissioning of the ATLAS reconstruction software with first data

Looking towards first LHC collisions, the ATLAS detector is being commissioned using the physics data available: cosmic rays and data taken during the LHC single beam operations at 450 GeV. During the installation of the ATLAS detector in the cavern, cosmic rays were collected with the different parts of the detector that were available. Combined cosmic runs taken with the full installed detector with and without magnetic field as well as a few single beam events recently recorded are being used to commission the full system prior to the first proton collisions.

Commissioning of the ATLAS Liquid Argon Calorimeter

The in-situ commissioning of the ATLAS liquid argon calorimeter is taking place since three years. During this period, it has been fully tested by means of frequent calibration runs, and the analysis of the large cosmic muon data samples and of the few beam splash events that occurred on September 10th, 2008. This has allowed to obtain a stable set of calibration constants for the first collisions, and to measure the in-situ calorimeter performances that were found to be at the expected level.

Commissioning of the Inner Tracker of the KLOE-2 experiment

The KLOE-2 experiment is undergoing commissioning at the DA$Φ$NE $e^{+}e^{-}$ collider of the Frascati National Laboratory of the INFN, after the integration of new detectors in the former KLOE apparatus. The Inner Tracker, a very light detector (material budget $<2\%X_{0}$), is one of the new subdetectors and it is composed of 4 cylindrical triple-GEM with a stereo X-V strips/pads readout. The commissioning phase of the Inner Tracker consists in the characterization of the detector response and in its performance evaluation. The method used to evaluate its detection efficiency is reported, to…

Commissioning of the ATLAS Muon Trigger Selection

The performance of the three-level ATLAS muon trigger as evaluated by using LHC data is presented. Events have been selected by using only the hardware-based Level-1 trigger in order to commission and to subsequently enable the (software-based) selections of the High Level Trigger. Studies aiming at selecting prompt muons from J/ψ and at reducing non prompt muon contamination have been performed. A brief overview on how the muon triggers evolve with increasing luminosity is given.

Readiness of the ATLAS Experiment for First Data

The ATLAS detector is one of the experiments at the LHC that will detect high-energy proton collisions at 14 TeV. The commissioning of the detector has started already in 2005 in parallel to the detector installation and is still in progress. The data taken so far corresponds to noise runs, cosmic muon events and beam background events from single beam in September 2008. We present the current status of the detector and performance results obtained during commissioning.

Results from the Commissioning of the ATLAS Pixel Detector with Cosmic data

The ATLAS pixel detector is the innermost detector of the ATLAS experiment at the Large Hadron Collider at CERN. With approximately 80 million readout channels, the ATLAS silicon pixel detector is a high-acceptance, high-resolution, low-noise tracking device. Providing the desired refinement in charged track pattern recognition capability in order to meet the stringent track reconstruction requirements, the pixel detector largely defines the ability of ATLAS to effectively resolve primary and secondary vertices and perform efficient flavor tagging essential for discovery of new physics. Being …

Results from the commissioning of the ATLAS Pixel detector

The ATLAS Pixel detector is a high-resolution, low-noise silicon-based device designed to provide tracking and vertexing information within a distance of 12 cm from the LHC beam axis. It consists of approximately 80 million pixel channels with radiation-hard front-end electronics connected through optical fibers to a custom-controlled DAQ system away from the detector. Following the successful installation of the detector in June 2007, an intense commissioning period was conducted in the year 2008 and more than 400,000 cosmic-ray tracks were recorded in conjunction with other ATLAS sub-detecto…

Commissioning of the ATLAS Electron and Photon Trigger Selection

Since the start-up of the LHC end of 2009, the trigger commissioning is in full swing. The ATLAS trigger system is divided into three levels: the hardware-based first level trigger, and the software-based second level trigger and Event Filter, collectively referred to as the High Level Trigger (HLT). Initially, events have been selected online based on the Level-1 selections with the HLT algorithms run but not rejecting any events. This has been an important step in the commissioning of these triggers to ensure their correct functioning and subsequently to enable the HLT selections. Due to inc…

Commissioning of the ATLAS Muon Spectrometer with Cosmic Rays

The ATLAS detector at the Large Hadron Collider has collected several hundred million cosmic ray events during 2008 and 2009. These data were used to commission the Muon Spectrometer and to study the performance of the trigger and tracking chambers, their alignment, the detector control system, the data acquisition and the analysis programs. We present the performance in the relevant parameters that determine the quality of the muon measurement. We discuss the single element efficiency, resolution and noise rates, the calibration method of the detector response and of the alignment system, the…

Commissioning of the ATLAS Level-1 Trigger with Cosmic Rays

The ATLAS detector at CERN's Large Hadron Collider will be exposed to proton-proton collisions from beams crossing at 40 MHz. A three-level trigger system was designed to select potentially interesting events and reduce the incoming rate to 100-200 Hz. The first trigger level (LVL1) is implemented in custom-built electronics, the second and third trigger levels are realized in software. Based on calorimeter information and hits in dedicated muon-trigger detectors, the LVL1 decision is made by the central-trigger processor yielding an output rate of less than 100 kHz. The allowed latency for th…

The ATLAS Inner Detector commissioning and calibration

The ATLAS Inner Detector is a composite tracking system consisting of silicon pixels, silicon strips and straw tubes in a 2 T magnetic field. Its installation was completed in August 2008 and the detector took part in data- taking with single LHC beams and cosmic rays. The initial detector operation, hardware commissioning and in-situ calibrations are described. Tracking performance has been measured with 7.6 million cosmic-ray events, collected using a tracking trigger and reconstructed with modular pattern-recognition and fitting software. The intrinsic hit efficiency and tracking trigger ef…

Development and test of a mini-Data Acquisition system for the High-Luminosity LHC upgrade of the ATLAS Monitored Drift Tube detector

New front-end electronics including ASICs and FPGA boards are under development for the ATLAS Monitored Drift Tube (MDT) detector to handle the large data rates and harsh environment expected at high-luminosity LHC runs. A mobile Data Acquisition (miniDAQ) system is designed to perform integration tests of these front-end electronics. In addition, it will be used for surface commissioning of 96 small-radius MDT (sMDT) chambers and for integration and commissioning of new front-end electronics on the present ATLAS MDT chambers. Details of the miniDAQ hardware and firmware are described in this …

用于ATLAS HL-LHC升级的sMDT缪子腔室的表面调试与性能

Surface Commissioning and Performance of the sMDT Muon Chambers for the ATLAS HL-LHC Upgrade

本文报告了ATLAS HL-LHC升级中102个sMDT缪子腔室在CERN的表面调试，验证了其低泄漏率、低暗电流、低噪声及高效率和空间分辨率，满足并超过设计要求。

Integration and commissioning of the ATLAS Muon spectrometer

The ATLAS experiment at the Large Hadron Collider (LHC) at CERN is currently waiting to record the first collision data in spring 2009. Its muon spectrometer is designed to achieve a momentum resolution of 10% pT(mu) = 1 TeV/c. The spectrometer consists of a system of three superconducting air-core toroid magnets and is instrumented with three layers of Monitored Drift Tube chambers (Cathode Strip Chambers in the extreme forward region) as precision detectors. Resistive Plate Chambers in the barrel and Thin Gap Chambers in the endcap regions provide a fast trigger system. The spectrometer pass…

FASER Tracker Detector Commissioning, Installation, and Functionality

FASER (ForwArd Search ExpeRiment) fills the axial blindspot of other, radially arranged LHC experiments. It is installed 480 meters from the ATLAS interaction point, along the collision axis. FASER will search for new, long-lived particles that may be hidden in the collimated reaction products exiting ATLAS. The tracking detector is an essential component for observing LLP signals. FASER's tracking stations use silicon microstrip detectors to measure the path of charged particles.This is a summary of one of FASER's latest papers "The tracking detector of the FASER experiment", which describes …

ATLAS Detector Status and Physics Startup Plans

The status of the ATLAS detector shortly before the start-up of the LHC is presented. The progress in the commissioning of the detector, as well as plans for early physics analysis are outlined.

Commissioning and installation of the new small-Diameter Muon Drift Tube (sMDT) detectors for the Phase-I upgrade of the ATLAS Muon Spectrometer

The Monitored Drift Tubes, as a part of the ATLAS muon spectrometer, are precision drift chambers designed to provide excellent spatial resolution and high tracking efficiency independent of the track angle. Through the life of the LHC and ATLAS experiment, this detector has already demonstrated that they provide precise tracking over large areas. The aim of the ATLAS muon spectrometer upgrade is to increase the muon trigger efficiency, precise muon momentum measurement and to improve the rate capability of the muon system in the high-background regions during the High-Luminosity LHC runs. To …

The upgraded Pixel detector and the commissioning of the Inner Detector tracking of the ATLAS experiment for Run-2 at the Large Hadron Collider

Run-2 of the Large Hadron Collider (LHC) will provide new challenges to track and vertex reconstruction with higher energies, denser jets and higher rates. Therefore the ATLAS experiment has constructed the first 4-layer Pixel Detector in HEP, installing a new pixel layer, also called Insertable B-Layer (IBL). The IBL is a fourth layer of pixel detectors, and has been installed in May 2014 at a radius of 3.3 cm between the existing Pixel Detector and a new smaller radius beam-pipe. The new detector, built to cope with the high radiation and expected occupancy, is the first large scale applicat…

The Topological Processor for the future ATLAS Level-1 Trigger: from design to commissioning

The ATLAS detector at LHC will require a Trigger system to efficiently select events down to a manageable event storage rate of about 400 Hz. By 2015 the LHC instantaneous luminosity will be increased up to 3 x 10^34 cm-2s-1, this represents an unprecedented challenge faced by the ATLAS Trigger system. To cope with the higher event rate and efficiently select relevant events from a physics point of view, a new element will be included in the Level-1 Trigger scheme after 2015: the Topological Processor (L1Topo). The L1Topo system, currently developed at CERN, will consist initially of an ATCA c…

ALICE Inner Tracking System Upgrade: construction and commissioning

ALICE (A Large Ion Collider Experiment) is the CERN LHC experiment optimized for the study of the strongly interacting matter produced in heavy-ion collisions and devoted to the characterization of the Quark-Gluon Plasma. To achieve the physics program for LHC Run 3 and 4, ALICE is undergoing a major upgrade of the experimental apparatus during the ongoing second long LHC shutdown. A key element of the ALICE upgrade is the substitution of the Inner Tracking System (ITS) with a completely new silicon-based detector whose features will allow the reconstruction of rare physics channels which coul…

The ATLAS Insertable B-Layer: from construction to operation

The ATLAS Insertable B-Layer (IBL) is the innermost layer of pixel detectors, and was installed in May 2014 at a radius of 3.3 cm from the beam axis, between the existing Pixel detector and a new smaller radius beam-pipe. The new detector, built to cope with high radiation and occupancy, is the first large scale application of 3D sensors and CMOS 130 nm technology. The IBL detector construction was completed within about two years (2012-2014), and the key features and challenges met during the IBL project are presented, as well as its commissioning and operational experience at the LHC.

Commissioning of the new ALICE Inner Tracking System

The upgrade of the Inner Tracking System (ITS) of ALICE (A Large Ion Collider Experiment) will extend measurements of heavy-flavour hadrons and low-mass dileptons to a lower transverse momentum than currently achieved and increase the readout capabilities to incorporate the full interaction. Furthermore, the tracking efficiency will be improved at low transverse momentum. To achieve this, the new ALICE ITS is comprised of seven layers of a custom Monolithic Active Pixel Sensor design known as ALPIDE, with a spatial resolution of $5\,\mathrm{μm}$. The use of the ALPIDE-based detector design wil…

Commissioning and Performance of the New ALICE Inner Tracking System in the First Phase of LHC Run 3

ALICE is one of the four experiments at the CERN Large Hadron Collider (LHC) specifically designed to study nuclear matter at extreme conditions of temperature and pressure. The LHC Run 3 started officially in July 2022 with proton-proton (pp) collisions at a centre-of-mass energy $\sqrt{s}$ = 13.6 TeV after a shutdown of more than two years to allow for the upgrade of both the accelerator and the experiments. To fulfill the requirements of the ALICE physics program for Run 3, new timing, tracking and multiplicity detectors have been installed in the ALICE central barrel both at mid- and forwa…

Development of a Depleted Monolithic CMOS Sensor in a 150 nm CMOS Technology for the ATLAS Inner Tracker Upgrade

The recent R&D focus on CMOS sensors with charge collection in a depleted zone has opened new perspectives for CMOS sensors as fast and radiation hard pixel devices. These sensors, labelled as depleted CMOS sensors (DMAPS), have already shown promising performance as feasible candidates for the ATLAS Inner Tracker (ITk) upgrade, possibly replacing the current passive sensors. A further step to exploit the potential of DMAPS is to investigate the suitability of equipping the outer layers of the ATLAS ITk upgrade with fully monolithic CMOS sensors. This paper presents the development of a deplet…

Cosmic Ray Muons Timing in the ATLAS Detector

In this talk I discuss the use of calorimeter timing both for detector commissioning and in searches for new physics. In particular I present real and simulated cosmic ray muons data results for the ATLAS Tile Calorimeter system. The analysis shows that several detector errors such as imperfect calibrations can be uncovered. I also demonstrate the use of ATLAS Tile Calorimeters excellent timing resolution in suppressing cosmic ray fake missing transverse energy in searches for supersymmetry.

Subpixel Mapping and Test Beam Studies with a HV2FEI4v2 CMOS-Sensor-Hybrid Module for the ATLAS Inner Detector Upgrade

The upgrade to the High Luminosity Large Hadron Collider will pose unprecedented challenges to the tracking systems of all experiments. Recent advancement of active pixel detectors designed in CMOS processes provide attractive alternatives to the well-established hybrid design using passive sensors. This article presents studies with a high-voltage CMOS active pixel sensor designed for the ATLAS tracker upgrade. The sensor is glued to the read-out chip of the Insertable B-Layer. The device under test is structured in smaller pixels than those of the attached read-out chip with information on t…

Rad-hard vertical JFET switch for the HV-MUX system of the ATLAS upgrade Inner Tracker

This work presents a new silicon vertical JFET (V-JFET) device, based on the trenched 3D-detector technology developed at IMB-CNM, to be used as switches for the High-Voltage powering scheme of the ATLAS upgrade Inner Tracker. The optimization of the device characteristics is performed by 2D and 3D TCAD simulations. Special attention has been paid to the on-resistance and the switch-off and breakdown voltages to meet the specific requirements of the system. In addition, a set of parameter values has been extracted from the simulated curves to implement a SPICE model of the proposed V-JFET tran…

Depleted fully monolithic CMOS pixel detectors using a column based readout architecture for the ATLAS Inner Tracker upgrade

Depleted monolithic active pixel sensors (DMAPS), which exploit high voltage and/or high resistivity add-ons of modern CMOS technologies to achieve substantial depletion in the sensing volume, have proven to have high radiation tolerance towards the requirements of ATLAS in the high-luminosity LHC era. Depleted fully monolithic CMOS pixels with fast readout architectures are currently being developed as promising candidates for the outer pixel layers of the future ATLAS Inner Tracker, which will be installed during the phase II upgrade of ATLAS around year 2025. In this work, two DMAPS prototy…

Commissioning of the Silicon Drift Detectors of the ALICE experiment at the LHC

Silicon Drift Detectors (SDD) equip the two central layers of the Inner Tracking System of the ALICE experiment at the LHC. Main results of systematic studies of detector performance including noise, gain, drift speed and charge collection measurements will be reported

ATLAS Pixel Detector: Operational Experience and Run-1 to Run-2 Transition

The Pixel Detector of the ATLAS experiment has shown excellent performance during the whole Run-1 of LHC. Taking advantage of the long shutdown, the detector was extracted from the experiment and brought to surface, to equip it with new service quarter panels, to repair modules and to ease installation of a new innermost layer, the Insertable B-Layer (IBL). An overview of the operational experience, the refurbishing of the Pixel Detector and of the IBL project as well as the experience in its construction, integration and commissioning are described.

Characterization of a depleted monolithic pixel sensors in 150 nm CMOS technology for the ATLAS Inner Tracker upgrade

This work presents a depleted monolithic active pixel sensor (DMAPS) prototype manufactured in the LFoundry 150\,nm CMOS process. DMAPS exploit high voltage and/or high resistivity inclusion of modern CMOS technologies to achieve substantial depletion in the sensing volume. The described device, named LF-Monopix, was designed as a proof of concept of a fully monolithic sensor capable of operating in the environment of outer layers of the ATLAS Inner Tracker upgrade in 2025 for the High Luminosity Large Hadron Collider (HL-LHC). This type of devices has a lower production cost and lower materia…

The ATLAS Inner Detector operation, data quality and tracking performance

The ATLAS Inner Detector is responsible for particle tracking in ATLAS experiment at CERN Large Hadron Collider (LHC) and comprises silicon and gas based detectors. The combination of both silicon and gas based detectors provides high precision impact parameter and momentum measurement of charged particles, with high efficiency and small fake rate. The ID has been used to exploit fully the physics potential of the LHC since the first proton-proton collisions at 7 TeV were delivered in 2009. The performance of track and vertex reconstruction is presented, as well as the operation aspects of the…

Alignment of the ATLAS Inner Detector Tracking System

The ATLAS detector, built at one of the interaction points of the Large Hadron Collider, is operational and has been collecting data from cosmic rays. This paper describes the track based alignment of the ATLAS Inner Detector tracker which was performed using cosmic rays collected in 2008. The alignment algorithms are described and the performance of the alignment is demonstrated by showing the resulting hit residuals and comparing track parameters of upper and lower segments of tracks. The impact of the alignment on physics measurements is discussed.

Alignment of the ATLAS Inner Detector Tracking System

The ATLAS detector at CERN's Large Hadron Collider (LHC) is equipped with a tracking system at its core (the Inner Detector, ID) consisting of silicon and gaseous straw tube detectors. The physics performance of the ID requires a precision alignment; a challenge involving complex algorithms and significant computing power. The alignment algorithms were already validated on: Combined Test Beam data, Cosmic Ray runs and simulated physics events. The alignment chain was tested on a daily basis in exercises that mimicked ATLAS data taking operations. ID commissioning after final installation into …

Characterization of a gigabit transceiver for the ATLAS inner tracker pixel detector readout upgrade

We present a gigabit transceiver prototype Application Specific Integrated Circuit (ASIC), GBCR, for the ATLAS Inner Tracker (ITk) Pixel detector readout upgrade. GBCR is designed in a 65-nm CMOS technology and consists of four upstream receiver channels, a downstream transmitter channel, and an Inter-Integrated Circuit (I2C) slave. The upstream channels receive the data at 5.12 Gbps passing through 5-meter 34-American Wire Gauge (AWG) Twin-axial (Twinax) cables, equalize them, retime them with a recovered clock, and then drive an optical transmitter. The downstream channel receives the data a…

The construction and commissioning of the CMS Silicon Strip Tracker

As the start up date for LHC approaches, the detectors are readying for data taking. Here a review will be given on the construction phase with insights into the various difficulties encountered during the process. An overview will also be given of the commissioning strategy and results obtained so far. The CMS tracker is the largest silicon microstrip detector ever built. Consisting of three main subsystems, Inner Barrel and Disks, Outer Barrel and End Caps, it is 5.4m long and is 2.4m in diameter. Total detector surface is an unprecedented 200m^2 with more than 15000 detector modules. The va…

Characterization and quality control test of a gigabit cable receiver ASIC (GBCR2) for the ATLAS Inner Tracker Detector upgrade

We present the characterization and quality control test of a gigabit cable receiver ASIC prototype, GBCR2, for the ATLAS Inner Tracker pixel detector upgrade. GBCR2 equalizes and retimes the uplink electrical signals from RD53B through a 6 m Twinax AWG34 cable to lpGBT. GBCR2 also pre-emphasizes downlink command signals through the same electrical connection from lpGBT to RD53B. GBCR2 has seven uplink channels each at 1.28 Gbps and two downlink channels each at 160 Mbps. The prototype is fabricated in a 65 nm CMOS process. The characterization of GBCR2 has been demonstrated that the total jit…

BESIII实验中圆柱形GEM内径迹探测器的建造、调试与安装

Construction, Commissioning, and Installation of the Cylindrical GEM Inner Tracker of the BESIII Experiment

针对BESIII内径迹探测器老化问题，本文介绍基于圆柱形GEM技术的新探测器CGEM-IT的建造、调试与安装过程，旨在提升空间分辨率并确保数据采集持续至2030年。

Tracking Performance of the ATLAS Inner Detector and Observation of Known Hadrons

The inner detector is the central tracking device of the ATLAS detector. In these proceedings the tracking performance of the inner detector is presented on collision data recorded at $\sqrt{s}$ = 900 GeV and 7 TeV. The identification of resonances like $Ξ$ and $Ω$ baryons in cascade decays via $K_{\mathrm{s}}$ and $Λ$ mesons is presented as well as the reconstruction of the $J / ψ$ and $ψ$(2S) mesons decaying into two muons. Furthermore, the performance of the track reconstruction and a data-driven method of estimating the track reconstruction efficiency as used in measurements of charged par…

A gigabit transceiver for the ATLAS inner tracker pixel detector readout upgrade

This paper presents the design and simulation results of a gigabit transceiver Application Specific Integrated Circuit (ASIC) called GBCR for the ATLAS Inner Tracker (ITk) Pixel detector readout upgrade. GBCR has four upstream receiver channels and a downstream transmitter channel. Each upstream channel operates at 5.12 Gbps, while the downstream channel operates at 2.56 Gbps. In each upstream channel, GBCR equalizes a signal received through a 5-meter 34-American Wire Gauge (AWG) twin-axial cable, retimes the data with a recovered clock, and drives an optical transmitter. In the downstream ch…

A Method to check the Connectivity for the ATLAS TRT Detector

We report on a technique developed to diagnostic for non working readout channels of the Transition Radiation Tracker (TRT), one of the three inner detectors of the ATLAS experiment. From a detailled study, we show that 99.6 % of the readout channels of the TRT endcap-detector are perfectly operational.

The design and test results of A Giga-Bit Cable Receiver (GBCR) for the ATLAS Inner Tracker Pixel Detector

This paper presents the design and test results of a Gigabit Cable Receiver ASIC called GBCR for the HL-LHC upgrade of the ATLAS Inner Tracker (ITk) pixel detector. Three prototypes (GBCR1, GBCR2, and GBCR3) have been designed in the CERN-identified 65 nm CMOS technology. GBCR receives seven (GBCR2) or six (GBCR3) channels (RX) each at 1.28 Gbps from the front-end readout chip RD53B via flex cables up to 1 meter and Twinax cables up to 5 meters and sends the equalized and retimed signals to lpGBT. Both GBCR2 and GBCR3 ASICs have two transmitting channels (TX) that pre-emphasize the signals fro…

The Performance and Development of the Inner Detector Trigger Algorithms at ATLAS for LHC Run 2

The upgrade to the ATLAS trigger for LHC Run 2 is presented including a description of the design and performance of the newly reimplemented tracking algorithms. The profiling infrastructure, constructed to provide prompt feedback from the optimisation procedure is described including the methods used to monitor the relative performance improvements as the code evolves. The performance of the trigger on the first data collected in the LHC Run 2 is presented.

Radiation Hard 3D Silicon Pixel Sensors for use in the ATLAS Detector at the HL-LHC

The High Luminosity LHC (HL-LHC) upgrade requires the planned Inner Tracker (ITk) of the ATLAS detector to tolerate extremely high radiation doses. Specifically, the innermost parts of the pixel system will have to withstand radiation fluences above $1\times10^{16}$ $n_{eq}cm^{-2}$. Novel 3D silicon pixel sensors offer a superior radiation tolerance compared to conventional planar pixel sensors, and are thus excellent candidates for the innermost parts of the ITk. This paper presents studies of 3D pixel sensors with pixel size $50 \times 50$ $μm^2$ mounted on the RD53A prototype readout chip. …

ATLAS内部径迹探测器（ITk）升级硅像素探测器数据链路测试系统的开发

Development of a Test System for Data Links of the ATLAS Inner Tracker (ITk) Upgrade Silicon Pixel Detector

针对ATLAS ITk升级的约2.6万条1.28Gb/s高速电链路，本文开发基于FPGA的DAQ测试系统，支持64通道并行BER测试与虚拟眼图，并通过校准及原型、预生产组件测试验证其链路质量认证能力。

Alternative glues for the production of ATLAS silicon strip modules for the Phase-II upgrade of the ATLAS Inner Detector

The Phase-II upgrade of the ATLAS detector for the High Luminosity Large Hadron Collider (HL-LHC) includes the replacement of the current Inner Detector with an all-silicon tracker consisting of pixel and strip detectors. The current Phase-II detector layout requires the construction of 20,000 strip detector modules consisting of sensor, circuit boards and readout chips, which are connected mechanically using adhesives. The adhesive between readout chips and circuit board is a silver epoxy glue as was used in the current ATLAS SemiConductor Tracker (SCT). This glue has several disadvantages, w…

The Monopix chips: Depleted monolithic active pixel sensors with a column-drain read-out architecture for the ATLAS Inner Tracker upgrade

Two different depleted monolithic CMOS active pixel sensor (DMAPS) prototypes with a fully synchronous column-drain read-out architecture were designed and tested: LF-Monopix and TJ-Monopix. These chips are part of a R&D effort towards a suitable implementation of a CMOS DMAPS for the HL-LHC ATLAS Inner Tracker. LF-Monopix was developed using a 150nm CMOS process on a highly resistive substrate (>2 k$Ω\,$cm), while TJ-Monopix was fabricated using a modified 180 nm CMOS process with a 1 k$Ω\,$cm epi-layer for depletion. The chips differ in their front-end design, biasing scheme, pixel pitch, di…

ATLAS ITk R2硅条探测器的测试束测量与计算机模拟

Test beam measurements and computer simulations of the ATLAS ITk R2 silicon strip detector

本文针对ATLAS ITk R2端盖条形模块进行电子束测量，评估其在垂直与倾斜入射下的性能，并利用Allpix-Squared框架进行模拟，通过实验对比验证了模块在高亮度LHC极端条件下的可靠性。

Prototype Active Silicon Sensor in 150 nm HR-CMOS Technology for ATLAS Inner Detector Upgrade

The LHC Phase-II upgrade will lead to a significant increase in luminosity, which in turn will bring new challenges for the operation of inner tracking detectors. A possible solution is to use active silicon sensors, taking advantage of commercial CMOS technologies. Currently ATLAS R&D programme is qualifying a few commercial technologies in terms of suitability for this task. In this paper a prototype designed in one of them (LFoundry 150 nm process) will be discussed. The chip architecture will be described, including different pixel types incorporated into the design, followed by simulation…

高亮度LHC下ATLAS内部径迹探测器的预期径迹测量性能

Expected Tracking Performance of the ATLAS Inner Tracker at the High-Luminosity LHC

为应对高亮度LHC每次束团交叉200次质子相互作用的挑战，ATLAS合作组将用全硅ITk替换现有内部探测器，适配软件实现高亮度下先进径迹重建，本文介绍其基于最新进展的预期性能。

The Pixel Detector of the ATLAS experiment for the Run2 at the Large Hadron Collider

The Pixel Detector of the ATLAS experiment has shown excellent performance during the whole Run-1 of LHC. Taking advantage of the long shutdown, the detector was extracted from the experiment and brought to surface, to equip it with new service quarter panels, to repair the modules and to ease installation of the Insertable B-Layer (IBL). The IBL is a fourth layer of pixel detectors, and has been installed in May 2014 between the existing Pixel Detector and a new smaller radius beam-pipe at a radius of 3.3 cm. To cope with the high radiation and pixel occupancy due to the proximity to the inte…

Track-Based Alignment of the Inner Detector of ATLAS

ATLAS is a multipurpose experiment at the LHC. The tracking system of ATLAS, embedded in a 2 T solenoidal field, is composed of different technologies: silicon planar sensors (pixel and microstrips) and drift-tubes. The procedure used to align the ATLAS tracker and the results of the alignment using data recorded during 2010 and 2011 using LHC proton-proton collision runs at 7 TeV are presented. Validation of the alignment is performed by measuring the alignment observables as well as many other physics observables, notably resonance invariant masses in a wide mass range. The E/p distributions…

测试ITkPixV2的极限：ATLAS内跟踪器像素探测器读出芯片

Testing the limits of ITkPixV2: the ATLAS inner tracker pixel detector readout chip

针对HL-LHC的ATLAS二期内跟踪器升级，本文首次在全设计要求极限下测试其最终量产读出芯片ITkPixV2，重点测量了活动诱导电流随击中率的变化，验证芯片在高亮度环境下的性能。