We study radio-frequency (RF) wireless power transfer (WPT) using a digital radio transmitter for applications where alternative analog transmit circuits are impractical. An important paramter for assessing the viability of an RF WPT system is its end-to-end efficiency. In this regard, we present a prototype test-bed comprising a software-defined radio (SDR) transmitter and an energy harvesting receiver with a low resistive load; employing an SDR makes our research meaningful for simultaneous wireless information and power transfer (SWIPT). We analyze the effect of clipping and non-linear amplification at the SDR on multisine waveforms. Our experiments suggest that when the DC input power at the transmitter is constant, high peak-to-average power ratio (PAPR) multisine are unsuitable for RF WPT over a flat-fading channel, due to their low average radiated power. The results indicate that the end-to-end efficiency is positively correlated to the average RF power of the waveform, and that it reduces with increasing PAPR. Consequently, digital modulations such as phase-shift keying (PSK) and quadrature amplitude modeulation (QAM) yield better end-to-end efficiency than multisines. Moreover, the end-to-end efficiency of PSK and QAM signals is invariant of the transmission bit rate. An in-depth analysis of the end-to-end efficiency of WPT reveals that the transmitter efficiency is lower than the receiver efficiency. Furthermore, we study the impact of a reflecting surface on the end-to-end efficiency of WPT, and assess the transmission quality of the information signals by evaluating their error vector magnitude (EVM) for SWIPT. Overall, the experimental observations of end-to-end efficiency and EVM suggest that, while employing an SDR transmitter with fixed DC input power, a baseband quadrature PSK signal is most suitable for SWIPT at large, among PSK and QAM signals.
Several different waveform processing techniques have been studied and proposed for the 5G new radio (NR) physical layer, to support new mixed numerology and asynchronous services. The evaluation and comparison of these different techniques is commonly based on matched waveform processing in the transmitter and receiver units. In this article, it is shown that different techniques can be flexibly mixed, allowing to separately optimize complexity-performance trade-offs for transmitter and receiver implementations. Mixing of different waveform processing techniques is possible by setting adequat…
This paper aims to handle the joint transmitter and noncoherent receiver design for multiuser multiple-input multiple-output (MU-MIMO) systems through deep learning. Given the deep neural network (DNN) based noncoherent receiver, the novelty of this work mainly lies in the multiuser waveform design at the transmitter side. According to the signal format, the proposed deep learning solutions can be divided into two groups. One group is called pilot-aided waveform, where the information-bearing symbols are time-multiplexed with the pilot symbols. The other is called learning-based waveform, wher…
In this paper, we investigate multi-dimensional chaotic signals with respect to wireless power transfer (WPT). Specifically, we analyze a multi-dimensional Lorenz-based chaotic signal under a WPT framework. By taking into account the nonlinearities of the energy harvesting process, closed-form analytical expressions for the average harvested energy are derived. Moreover, the practical limitations of the high power amplifier (HPA) at the transmitter are also taken into consideration. We interestingly observe that for these types of signals, high peak-to-average-power-ratio (PAPR) is not the onl…
Wireless signals contain transmitter specific features, which can be used to verify the identity of transmitters and assist in implementing an authentication and authorization system. Most recently, there has been wide interest in using deep learning for transmitter identification. However, the existing deep learning work has posed the problem as closed set classification, where a neural network classifies among a finite set of known transmitters. No matter how large this set is, it will not include all transmitters that exist. Malicious transmitters outside this closed set, once within commun…
In this letter, a wireless transmitter using the new architecture of programmable metasurface is presented. The proposed transmitter does not require any filter, nor wideband mixer or wideband power amplifier, thereby making it a promising hardware architecture for cost-effective wireless communications systems in the future. Using experimental results, we demonstrate that a programmable metasurface-based 8-phase shift-keying (8PSK) transmitter with 8*32 phase adjustable unit cells can achieve 6.144 Mbps data rate over the air at 4.25 GHz with a comparable bit error rate (BER) performance as t…
Due to imperfections in transmitters' hardware, wireless signals can be used to verify their identity in an authorization system. While deep learning was proposed for transmitter identification, the majority of the work has focused on classification among a closed set of transmitters. Malicious transmitters outside this closed set will be misclassified, jeopardizing the authorization system. In this paper, we consider the problem of recognizing authorized transmitters and rejecting new transmitters. To address this problem, we adapt the most prominent approaches from the open set recognition a…
Free positioning of receivers is one of the key requirements for many wireless power transfer (WPT) applications, required from the end-user point of view. However, realization of stable and effective wireless power transfer for freely positioned receivers is technically challenging task because of the requirement of complex control and tuning. In this paper, we propose a concept of automatic receiver tracking and power channeling for multi-transmitter WPT systems using uncoupled transmitter and uncoupled repeaters. Each transmitter-repeater pair forms an independent power transfer channel pro…
Distributed antenna arrays have been proposed for many applications ranging from space-based observatories to automated vehicles. Achieving good performance in distributed antenna systems requires stringent synchronization at the wavelength and information level to ensure that the transmitted signals arrive coherently at the target, or that scattered and received signals can be appropriately processed via distributed algorithms. In this paper we address the challenge of high precision time synchronization to align the operations of elements in a distributed antenna array and to overcome time-v…
The optical wireless communication (OWC) with the intensity modulation (IM), requires the modulated radio frequency (RF) signal to be real and non-negative. To satisfy the requirements, this paper proposes two types of mixed orthogonal frequency division multiplexing (X-OFDM) waveform. The Hermitian symmetry (HS) character of the sub-carriers in the frequency domain, guarantees the signal in the time domain to be real, which reduces the spectral efficiency to $1/2$. For the odd sub-carriers in the frequency domain, the signal in the time domain after the inverse fast fourier transform (IFFT) i…
Wireless signals are commonly used for communications. Emerging applications are giving new functions to wireless signals, in which wireless sensing is the most attractive one. Channel state information (CSI) is not only the parameter for channel equalization in communications but also the indicator for wireless sensing. However, due to the broadcast nature of wireless signals, eavesdroppers can easily capture legitimate user signals and violate user privacy by measuring CSI. Moreover, the advancement of hardware simplifies illegal eavesdropping since smart devices can track over-the-air signa…
Waveform optimization has recently been shown to be a key technique to boost the efficiency and range of far-field wireless power transfer (WPT). Current research has optimized transmit waveform adaptive to channel state information (CSI) and accounting for energy harvester (EH)'s non-linearity but under the assumption of linear high power amplifiers (HPA) at the transmitter. This paper proposes a channel-adaptive waveform design strategy that optimizes the transmitter's input waveform considering both HPA and EH non-linearities. Simulations demonstrate that HPA's non-linearity degrades the en…
This article proposes a novel system concept named universal wireless power transfer, in which power can be wirelessly transferred between different entities (e.g. vehicles, robots, homes, grid facilities, consumer electronic devices, etc.) equipped with proper energy transmitters and receivers, whether stationary or in motion. This concept generalizes individually existing wireless power transfer systems, where a specific wireless power transfer technology is used, and where the wireless energy transmitter or receiver is fixed. As a result, energy mobility, flexibility, and convenience are si…
Wireless Energy Transfer (WET) has recently emerged as an appealing solution for power supplying mobile / Internet of Things (IoT) devices. As an enabling WET technology, Resonant Beam Charging (RBC) is well-documented for its long-range, high-power, and safe "WiFi-like" mobile power supply. To provide high-quality wireless charging services for multi-user in a given region, we formulate a deployment problem of multiple RBC transmitters for balancing the charging fairness and quality of charging service. Based on the RBC transmitter's coverage model and receiver's charging / discharging model,…
Some new properties of the chaotic signal have been implemented in communication system applications recently. However, due to the broadband property of the chaotic signal, it is very difficult for a practical transducer or antenna to convert such a broadband signal into a signal that would be suitable for practical band-limited wireless channel. Thus, the use of chaos property to improve the performance of conventional communication system without changing the system configuration becomes a critical issue in communication with chaos. In this paper, chaotic baseband waveform generated by a cha…
A Unified Multicarrier Waveform Framework for Next-generation Wireless Networks: Principles, Performance, and Challenges
Sun Yat-sen University（中山大学）；Guangdong Provincial Key Laboratory of Sea-Air-Space Communication, China（中国海空天通信广东省重点实验室）；Nanyang Technological University（南洋理工大学）；AUMOVIO-NTU Corporate Lab（奥莫维欧-南洋理工大学企业实验室）；Southeast University（东南大学）；National Mobile Communications Research Laboratory（移动通信国家重点实验室）；Frontiers Science Center for Mobile Information Communication and Security（移动信息通信与安全前沿科学中心）；Purple Mountain Laboratories（紫金山实验室）；South China University of Technology（华南理工大学）；University of Essex（埃塞克斯大学）
University of California, Los Angeles（加利福尼亚大学洛杉矶分校）
As the Internet of Things (IoT) continues to grow, ensuring the security of systems that rely on wireless IoT devices has become critically important. Deep learning-based passive physical layer transmitter authorization systems have been introduced recently for this purpose, as they accommodate the limited computational and power budget of such devices. These systems have been shown to offer excellent outlier detection accuracies when trained and tested on a fixed authorized transmitter set. However in a real-life deployment, a need may arise for transmitters to be added and removed as the aut…
This paper advances the state of the art by proposing the first comprehensive analysis and experimental evaluation of adversarial learning attacks to wireless deep learning systems. We postulate a series of adversarial attacks, and formulate a Generalized Wireless Adversarial Machine Learning Problem (GWAP) where we analyze the combined effect of the wireless channel and the adversarial waveform on the efficacy of the attacks. We propose a new neural network architecture called FIRNet, which can be trained to "hack" a classifier based only on its output. We extensively evaluate the performance…
In this paper, we study a multi-sine multiple-input multiple-output (MIMO) wireless power transfer (WPT) system with the objective to increase the output DC power. We jointly optimize the multi-sine waveform and beamforming accounting for the rectenna nonlinearity, and consider two combining schemes for the rectennas at the receiver, namely DC and RF combinings. For DC combining, the waveform and transmit beamforming are optimized, as a function of the channel state information (CSI). For RF combining, the optimal transmit and receive beamformings are provided in closed form and the waveform i…
Istanbul Technical University（伊斯坦布尔理工大学）；Bilkent University（比尔肯特大学）
In this paper, a deep learning based receiver is proposed for a collection of multi-carrier wave-forms including both current and next-generation wireless communication systems. In particular, we propose to use a convolutional neural network (CNN) for jointly detection and demodulation of the received signal at the receiver in wireless environments. We compare our proposed architecture to the classical methods and demonstrate that our proposed CNN-based architecture can perform better on different multi-carrier forms including OFDM and GFDM in various simulations. Furthermore, we compare the t…
In this paper, we design, prototype, and experiment a closed-loop radiative wireless power transfer (WPT) system with adaptive waveform and beamforming using limited feedback. Spatial and frequency domains are exploited by jointly utilizing multi-sine waveform and multi-antenna beamforming at the transmitter in WPT system to adapt to the multipath fading channel and boost the output dc power. A closed-loop architecture based on a codebook design and a low complexity over-the-air limited feedback using an IEEE 802.15.4 RF interface is proposed. The codebook consists of multiple codewords where …
In this paper, we study the waveform and passive beamforming design for intelligent reflecting surface (IRS)-aided wireless power transfer (WPT). Generalized multi-user and low complexity single-user algorithms are derived based on alternating optimization (AO) framework to maximize the weighted sum output DC current, subject to transmit power constraints and passive beamforming phases unit modulus constraints. The input signal waveform and IRS passive beamforming phase shifts are jointly designed as a function of users' individual frequency-selective channel state information (CSI). The energ…
University of Maryland（马里兰大学）；Intelligent Automation, Inc.（智能自动化公司）
We consider a wireless communication system that consists of a background emitter, a transmitter, and an adversary. The transmitter is equipped with a deep neural network (DNN) classifier for detecting the ongoing transmissions from the background emitter and transmits a signal if the spectrum is idle. Concurrently, the adversary trains its own DNN classifier as the surrogate model by observing the spectrum to detect the ongoing transmissions of the background emitter and generate adversarial attacks to fool the transmitter into misclassifying the channel as idle. This surrogate model may diff…
We consider a hybrid active-passive radar system that employs a wireless source as a passive illuminator of opportunity (IO) and a co-channel active radar transmitter operating in the same frequency band to seek spectral efficiency. The hybrid system can take advantage of the strengths of passive radar (e.g., energy efficiency, bi-/multi-static configuration, and spatial diversity) as well as those of active radar (dedicated transmitter, flexible transmit beam steering, waveform optimized for sensing, etc.). To mitigate the mutual interference and location-induced timing uncertainty between th…
The coexistence of different wireless communication systems such as LTE and Wi-Fi by sharing the unlicensed band is well studied in the literature. In these studies, various methods are proposed to support the coexistence of systems, including listen-before-talk mechanism, joint user association and resource allocation. However, in this study, the coexistence of different waveform structures in the same resource elements are studied under the theory of non-orthogonal multiple access. This study introduces a paradigm-shift on NOMA towards the application-centric waveform coexistence. Throughout…
This paper presents a novel massive multiple-input multiple-output (MIMO) transmission in beam domain for optical wireless communications. The optical base station equipped with massive optical transmitters communicates with a number of user terminals (UTs) through a transmit lens. Focusing on LED transmitters, we analyze light refraction of the lens and establish a channel model for optical massive MIMO transmissions. For a large number of LEDs, channel vectors of different UTs become asymptotically orthogonal. We investigate the maximum ratio transmission and regularized zero-forcing precodi…
University of Maryland（马里兰大学）；Intelligent Automation, Inc.（智能自动化公司）
We consider a wireless communication system that consists of a transmitter, a receiver, and an adversary. The transmitter transmits signals with different modulation types, while the receiver classifies its received signals to modulation types using a deep learning-based classifier. In the meantime, the adversary makes over-the-air transmissions that are received as superimposed with the transmitter's signals to fool the classifier at the receiver into making errors. While this evasion attack has received growing interest recently, the channel effects from the adversary to the receiver have be…
In this paper we present a method that prevents an unauthorized receiver (URx) from correctly estimating the Doppler shift present in an orthogonal frequency division multiplexing (OFDM) wireless signal. To prevent this estimation we propose to insert an artificial frequency variation in the transmitted signal that mimics a transmitter (Tx) movement with a spoofed/fake speed. This spoofed Doppler shift does not affect data demodulation since it can be compensated at the legitimate receiver (LRx). We evaluate our method for its efficacy through simulations and we show that it offers a reliable …
Clutter-Resilient ISAC for Low-Altitude Wireless Networks: A 5G Base Station-Compatible Protocol, Waveform, and Prototype
Nanjing University of Information Science and Technology（南京信息工程大学）；Southern University of Science and Technology（南方科技大学）；Southeast University（东南大学）；Aerospace Information Research Institute, Chinese Academy of Sciences（中国科学院空天信息创新研究院）
We propose a learning-based method for the joint design of a transmit and receive filter, the constellation geometry and associated bit labeling, as well as a neural network (NN)-based detector. The method maximizes an achievable information rate, while simultaneously satisfying constraints on the adjacent channel leakage ratio (ACLR) and peak-to-average power ratio (PAPR). This allows control of the tradeoff between spectral containment, peak power, and communication rate. Evaluation on an additive white Gaussian noise (AWGN) channel shows significant reduction of ACLR and PAPR compared to a …
By reconfiguring the propagation environment of electromagnetic waves artificially, reconfigurable intelligent surfaces (RISs) have been regarded as a promising and revolutionary hardware technology to improve the energy and spectrum efficiency of wireless networks. In this paper, we study a RIS aided multiuser multiple-input single-output (MISO) wireless power transfer (WPT) system, where the transmitter is equipped with a constant-envelope analog beamformer. We formulate a novel problem to maximize the total received power of all the users by jointly optimizing the beamformer at transmitter …
A small-cell network with multiple transmitters and unreliable wireless backhaul is considered for secrecy enhancement. The small-cell network is operating under a spectrum sharing agreement with a primary network in a cognitive radio system. A constraint on the desired outage probability at the primary receiver is assumed as a part of the spectrum sharing agreement. The reliability of the wireless backhaul links are modeled by a set of independent and identically distributed Bernoulli random variables. A sub-optimal and an optimal small-cell transmitter selection (TS) scheme is proposed to im…
In this paper we consider wireless energy transfer for a point-to-point link. The energy transmitter sees a finite number of independent channel realizations, and, armed with (causal) knowledge of the channels, must decide how much energy to transmit in each time slot. The objective is to maximize the expected energy transferred to the receiver at the end of the time period. We show that the optimal energy allocation policy is binary: the transmitter sends no energy or all energy in a slot with this decision based on a simple threshold on the channel. As intuition demands, this threshold for t…
The semantic communication system enables wireless devices to communicate effectively with the semantic meaning of the data. Wireless powered Internet of Things (IoT) that adopts the semantic communication system relies on harvested energy to transmit semantic information. However, the issue of energy constraint in the semantic communication system is not well studied. In this paper, we propose a semantic-based energy valuation and take an economic approach to solve the energy allocation problem as an incentive mechanism design. In our model, IoT devices (bidders) place their bids for the ener…
In this letter, we consider the control of an energy self-sufficient receiver in a multi-access network with simultaneous wireless information and energy transfer. Multiple transmitters send data to a common receiver whose only source of energy is a finite size battery which is recharged only from the energy harvested from incoming RF signals. The nodes access the channel randomly resulting in a packet collision when multiple transmitters simultaneously access the channel. The receiver takes samples from the received RF signal to calculate the probability of a collision. The objective is to ma…
Coordinating the operations of separate wireless systems at the wavelength level can lead to significant improvements in wireless capabilities. We address a fundamental challenge in distributed radio frequency system cooperation - inter-node phase alignment - which must be accomplished wirelessly, and is particularly challenging when the nodes are in relative motion. We present a solution to this problem that is based on a novel combined high-accuracy ranging and frequency transfer technique. Using this approach, we present the design of the first fully wireless distributed system operating at…
In this paper, we propose a unified SWIPT signal and its architecture design in order to take advantage of both single tone and multi-tone signaling by adjusting only the power allocation ratio of a unified signal. For this, we design a novel unified and integrated receiver architecture for the proposed unified SWIPT signaling, which consumes low power with an envelope detection. To relieve the computational complexity of the receiver, we propose an adaptive control algorithm by which the transmitter adjusts the communication mode through temporal convolutional network (TCN) based asymmetric p…
In recent years, the demand for high speed wireless networking has increased considerably due to the enormous number of devices connected to the Internet. In this context, optical wireless communication (OWC) has received tremendous interest in the context of next generation wireless networks where OWC offers a huge unlicensed bandwidth using optical bands. OWC systems are directional and can naturally provide multiple-input and multiple-output (MIMO) configurations serving multiple users using a high number of transmitters in the indoor environment to ensure coverage. Therefore, multiuser int…
Multi-Functional Chirp Signalling for Next-Generation Multi-Carrier Wireless Networks: Communications, Sensing and ISAC Perspectives
University of Essex（埃塞克斯大学）；University of Surrey（萨里大学）；University College London（伦敦大学学院）；Nanyang Technological University（南洋理工大学）；University of Southampton（南安普顿大学）
We propose a mechanism for distributed resource management and interference mitigation in wireless networks using multi-agent deep reinforcement learning (RL). We equip each transmitter in the network with a deep RL agent that receives delayed observations from its associated users, while also exchanging observations with its neighboring agents, and decides on which user to serve and what transmit power to use at each scheduling interval. Our proposed framework enables agents to make decisions simultaneously and in a distributed manner, unaware of the concurrent decisions of other agents. More…
