Fifth-generation (5G) cellular systems are likely to operate in the centimeter-wave (3-30 GHz) and millimeter-wave (30-300 GHz) frequency bands, where a vast amount of underutilized bandwidth exists world-wide. To assist in the research and development of these emerging wireless systems, a myriad of measurement studies have been conducted to characterize path loss in urban environments at these frequencies. The standard theoretical free space (FS) and Stanford University Interim (SUI) empirical path loss models were recently modified to fit path loss models obtained from measurements performed at 28 GHz and 38 GHz, using simple correction factors. In this paper, we provide similar correction factors for models at 60 GHz and 73 GHz. By imparting slope correction factors on the FS and SUI path loss models to closely match the close-in (CI) free space reference distance path loss models, millimeter-wave path loss can be accurately estimated (with popular models) for 5G cellular planning at 60 GHz and 73 GHz. Additionally, new millimeter-wave beam combining path loss models are provided at 28 GHz and 73 GHz by considering the simultaneous combination of signals from multiple antenna pointing directions between the transmitter and receiver that result in the strongest received power. Such directional channel models are important for future adaptive array systems at millimeter-wave frequencies.
Future cellular systems will make use of millimeter wave (mmWave) frequency bands. Many users in these bands are located indoors, i.e., inside buildings, homes, and offices. Typical building material attenuations in these high frequency ranges are of interest for link budget calculations. In this paper, we report on a collaborative measurement campaign to find the attenuation of several typical building materials in three potential mmWave bands (28, 73, 91 GHz). Using directional antennas, we took multiple measurements at multiple locations using narrow-band and wide-band signals, and averaged…
In this paper, two large-scale fading path loss models are presented based on indoor and outdoor channel measurements at 73 GHz. The line-of-sight millimeter-wave propagation measurement campaigns were uniquely conducted within the indoor and outdoor environments at an airport setting, i.e., the Boise Airport. The channel measurements were made with directional transmit and receive antennas with a 24 dBi gain at different receive antenna heights. From the measured data, we obtained the parameters of two path loss models, i.e., the close-in reference distance model (CIM) and the floating-interc…
We here propose a novel cost-effective millimeter-level resolution photonic multiband radar system using a single MZM driven by a 1-GHz-bandwidth LFM signal. It experimentally shows an ~8.5-mm range resolution through coherence-processing-free multiband data fusion.
With the expected adoption of millimeter wave technologies for industrial communication, it is fundamentally important to properly understand the radio channel characteristics of such environments. This paper presents the setup, scenario and results of a measurement campaign at 28 GHz in a machine hall. The radio channel was measured with a bandwidth of 2 GHz and both large scale parameters and directional information were extracted. Evaluation of the power delay profiles shows that the channel contains dense multipath components. A path loss model is parameterized and blockage losses, RMS del…
We present measurements of the 28 GHz self-interference channel for full-duplex sectorized multi-panel millimeter wave (mmWave) systems, such as integrated access and backhaul. We measure the isolation between the input of a transmitting phased array panel and the output of a co-located receiving phased array panel, each of which is electronically steered across a number of directions in azimuth and elevation. In total, nearly 6.5 million measurements were taken in an anechoic chamber to densely inspect the directional nature of the coupling between 256-element phased arrays. We observe that h…
This paper presents a 2 x 2 millimeter wave (mm-wave) multiple-input-multiple-output (MIMO) testbed that operates at around 30 GHz. The link assessment of the system operating at 26.25 GHz was carried out on a test bench, with a short communication distance between the transmitting and receiving antennas. A user-programmable, reconfigurable and real-time signal processing field-programmable gate arrays (FPGAs)-based software defined radio (SDR) system was employed as part of the testbed to validate the system-level performance for a downlink time division long-term evolution (TD-LTE) duplex sc…
Picocellular architectures are essential for providing the spatial reuse required to satisfy the ever-increasing demand for mobile data. A key deployment challenge is to provide backhaul connections with sufficiently high data rate. Providing wired support (e.g., using optical fiber) to pico base stations deployed opportunistically on lampposts and rooftops is impractical, hence wireless backhaul becomes an attractive approach. A multihop mesh network comprised of directional millimeter wave links is considered here for this purpose. The backhaul design problem is formulated as one of joint ro…
This paper presents selected results from a channel measurement campaign conducted in a shopping mall scenario at 158 GHz. The focus is on the statistical analysis of the collected measurement data in terms of directional channel gain. Although most power is received from the line-of-sight (LOS) direction, significant multipaths arrive from all measured azimuth directions. The median of the sorted directional channel gain can be approximated by a linear curve showing an offset of about 10 dB with respect to the LOS direction.
Ultra-low latency and high reliability communications are the two defining characteristics of Tactile Internet (TI). Nevertheless, some TI applications would also require high data-rate transfer of audio-visual information to complement the haptic data. Using Millimeter wave (mmWave) communications is an attractive choice for high datarate TI applications due to the availability of large bandwidth in the mmWave bands. Moreover, mmWave radio access is also advantageous to attain the airinterface-diversity required for high reliability in TI systems as mmWave signal propagation significantly dif…
In this paper, we present a novel real-time multiple-input-multiple-output (MIMO) channel sounder for the 28 GHz band. Until now, most investigations of the directional characteristics of millimeter-wave channels have used mechanically rotating horn antennas. In contrast, the sounder presented here is capable of performing horizontal and vertical beam steering with the help of phased arrays. Due to its fast beam-switching capability, the proposed sounder can perform measurements that are directionally resolved both at the transmitter(TX) and receiver (RX) in 1.44 milliseconds compared to the m…
A cost-effective millimeter-wave (MMW) joint radar-communication (JRC) system with super resolution is proposed and experimentally demonstrated, using optical heterodyne up-conversion and self-coherent detection down-conversion techniques. The point lies in the designed coherent dual-band constant envelope linear frequency modulation-orthogonal frequency division multiplexing (LFM-OFDM) signal with opposite phase modulation indexes for the JRC system. Then the self-coherent detection, as a simple and low-cost means, is accordingly facilitated for both de-chirping of MMW radar and frequency dow…
In this paper, we present 3D high resolution radar imaging process at millimeter-Wave (mmWave) frequencies by creating the effect of a large aperture synthetically. We use a low cost fully integrated Frequency Modulated Continuous Wave (FMCW) radar operating at $\rm 79\;GHz$ and then perform Synthetic Aperture Radar (SAR) imaging in the near-filed zone. At the end, we conduct a real experiment and present the reconstructed image.
Exploiting Out-of-Band Information for Millimeter-Wave MIMO Channel Estimation: Performance in Static and Dynamic Scenarios
Institute of Telecommunications, TU Wien（维也纳工业大学电信研究所）；Christian Doppler Laboratory for Digital Twin assisted AI for sustainable Radio Access Networks（可持续无线电接入网络数字孪生辅助人工智能克里斯蒂安·多普勒实验室）
Exploiting the millimeter wave (mmWave) band has recently attracted considerable attention as a potential solution to widespread deployment of device-to-device (D2D) communication challenges, namely, spectrum scarcity and interference. However, its directional nature makes the utilization of mmWave band a challenging task as it requires careful beam alignment between the D2D transmitter and receiver. In this paper, we investigate the impact of inaccurate angle-of-arrival (AoA) estimation as a beam alignment impairment on the performance of a directional mmWave D2D network. We have used tools f…
We study the distribution of the interference power in a millimeter wave (mmWave) cellular network. Such interference is random and highly dependent on the employed transmission technique, as well as the varying channel conditions and the varying association between users and base stations. Traditional networks at lower frequencies usually employ omnidirectional transmission which creates an (almost) equal amount of interference in any direction. MmWave networks, however, must employ directional beamforming transmission in order to compensate for the high path loss in mmWave frequency bands. T…
5G millimeter wave (mmWave) technology is envisioned to be an integral part of next-generation vehicle-to-everything (V2X) networks and autonomous vehicles due to its broad bandwidth, wide field of view sensing, and precise localization capabilities. The reliability of mmWave links may be compromised due to difficulties in beam alignment for mobile channels and due to blocking effects between a mmWave transmitter and a receiver. In this paper, we study the channel characteristics for mmWave and sub-6 GHz V2X communications using ray-tracing simulations. We present results for time-varying path…
The initial access is required to establish a connection between millimeter wave access point (AP) and users. The large isotropic pathloss at high frequencies can be mitigated by the use of highly directional antennas. However, it complicated the initial access procedures and increased the latency, defying one of the major low latency objective of 5G systems. Beam training algorithms are developed for the AP as well as for the users to find the desired beam quickly and reduce the initial access delay. But, these beam training protocols have to be run very frequently due to outage events, user'…
This paper provides indoor reflection, scattering, transmission, and large-scale path loss measurements and models, which describe the main propagation mechanisms at millimeter wave and Terahertz frequencies. Channel properties for common building materials (drywall and clear glass) are carefully studied at 28, 73, and 140 GHz using a wideband sliding correlation based channel sounder system with rotatable narrow-beam horn antennas. Reflection coefficient is shown to linearly increase as the incident angle increases, and lower reflection loss (e.g., stronger reflections) are observed as freque…
Millimeter-wave (mmWave) and Terahertz (THz) will be used in the sixth-generation (6G) wireless systems, especially for indoor scenarios. This paper presents an indoor three-dimensional (3-D) statistical channel model for mmWave and sub-THz frequencies, which is developed from extensive channel propagation measurements conducted in an office building at 28 GHz and 140 GHz in 2014 and 2019. Over 15,000 power delay profiles (PDPs) were recorded to study channel statistics such as the number of time clusters, cluster delays, and cluster powers. All the parameters required in the channel generatio…
This paper proposes a three-dimensional (3D) communication channel model for an indoor environment considering the effect of the Hypersurface. The Hypersurface is a software controlled intelligent metasurface, which can be used to manipulate electromagnetic waves, as for example for non-specular reflection and full absorption. Thus it can control the impinging rays from a transmitter towards a receiver location in both LOS and NLOS paths, e.g. to combat distance and improve wireless connectivity. We focus on the 60 GHz mmWave frequency band due to its increasing significance in 5G/6G networks …
Covert communication prevents legitimate transmission from being detected by a warden while maintaining certain covert rate at the intended user. Prior works have considered the design of covert communication over conventional low-frequency bands, but few works so far have explored the higher-frequency millimeter-wave (mmWave) spectrum. The directional nature of mmWave communication makes it attractive for covert transmission. However, how to establish such directional link in a covert manner in the first place remains as a significant challenge. In this paper, we consider a covert mmWave comm…
To meet the demand of supreme data rates in terabits-per-second, the next-generation mobile system needs to exploit the abundant spectrum in the millimeter-wave and terahertz bands. However, high-frequency transmission heavily relies on large-scale antenna arrays to reap high beamforming gain, used to compensate for severe propagation loss. It raises a problem of omni-directional beamforming during the phase of initial access, where a base station is required to broadcast synchronization signals and system information to all users within its coverage. This paper proposes a novel initial beamfo…
Path gain and effective directional gain in azimuth in urban canyons from actual rooftop base station sites are characterized based on a massive data set of 3000 links on 12 streets in two cities, with over 21 million individual continuous wave power measurements at 28 GHz using vertically polarized antennas. Large street-to-street path gain variation is found, with median street path gain varying over 30 dB at similar distances. Coverage in the street directly illuminated by a roof edge antenna is found to suffer an average excess loss of 11 dB relative to free space at 200 m, with empirical …
A fully-digital wideband joint communication-radar (JCR) with a multiple-input-multiple-output (MIMO) architecture at the millimeter-wave (mmWave) band will enable high joint communication and radar performance with enhanced design flexibility. A quantized receiver with few-bit analog-to-digital converters (ADCs) will enable a practical JCR solution with reduced power consumption for futuristic portable devices and autonomous vehicles. In this paper, we present a joint communication-radar proof-of-concept platform, named JCR70, to evaluate and demonstrate the performance of these JCR systems u…
Next-generation wireless networks must enable emerging technologies such as augmented reality and connected autonomous vehicles via wide range of wireless services that span enhanced mobile broadband (eMBB), as well as ultra-reliable low-latency communication (URLLC). Existing wireless systems that solely rely on the scarce sub-6 GHz, microwave ($μ$W) frequency bands will be unable to meet such stringent and mixed service requirements for future wireless services due to spectrum scarcity. Meanwhile, operating at high-frequency millimeter wave (mmWave) bands is seen as an attractive solution, p…
Massive multiple-input multiple-out (MIMO) technology is vital in millimeter-wave (mmWave) bands to obtain large array gains. However, there are practical challenges, such as high hardware cost and power consumption in such systems. A promising solution to these problems is to adopt a hybrid beamforming architecture. This architecture has a much lower number of transceiver (TRx) chains than the total antenna number, resulting in cost- and energy-efficient systems. In this paper, we present a real-time mmWave (28 GHz) massive MIMO testbed with hybrid beamforming. This testbed has a 64-antenna/1…
Blockage by the human hand/body is an important impairment in realizing practical millimeter wave wireless systems. Prior works on blockage modeling are either based on theoretical studies of double knife edge diffraction or its modifications, high-frequency simulations of electromagnetic effects, or measurements with experimental millimeter wave prototypes. While such studies are useful, they do not capture the form-factor constraints of user equipments (UEs). In this work, we study the impact of hand/body blockage with a UE at $28$ GHz built on Qualcomm's millimeter wave modem, antenna modul…
