Despite the promising gains, free-space optical (FSO) communication is severely influenced by atmospheric turbulence and pointing error issues, which make its practical design a bit challenging. In this paper, with the aim to increase the communication coverage and improve the system performance, reconfigurable intelligent surfaces (RISs) are considered in an FSO communication setup, in which both atmospheric turbulence and pointing errors are considered. Closed-form expressions for the outage probability, average bit error rate, and channel capacity are derived assuming large number of reflecting elements at the RIS. Specifically, according to central limit theorem (CLT), while assuming multiple reflecting elements approximate expressions are proposed. It is shown that the respective accuracies increase as the number of elements at the RIS increases. Illustrative numerical examples are shown along with insightful discussions. Finally, Monte Carlo simulations are presented to verify the correctness of the analytical results.
This work considers a point-to-point link where a reconfigurable intelligent surface assists the communication between transmitter and receiver. The system rate, energy efficiency, and their trade-off are optimized with respect to the number of individually tunable elements of the intelligent surface. The resource allocation accounts for the communication phase and for the overhead due to channel estimation and to reporting the optimized resource allocation to the intelligent surface. Numerical results confirm the optimality of the proposed methods and show the potential gains of reconfigurabl…
In this report, we summarize the end-to-end signal-to-noise ratio and the rate of half-duplex, full-duplex, amplify-and-forward, and decode-and-forward relay-aided communications, and well as the signal-to-noise ratio and the rate of the emerging technology known as reconfigurable intelligent surfaces.
Reconfigurable intelligent surfaces have emerged as a promising technology for future wireless networks. Given that a large number of reflecting elements is typically used, and that the surface has no signal processing capabilities, a major challenge is to cope with the overhead that is required to estimate the channel state information and to report the optimized phase shifts to the surface. This issue has not been addressed by previous works, which do not explicitly consider the overhead during the resource allocation phase. This work aims at filling this gap, developing an overhead-aware re…
In reconfigurable intelligent surfaces (RISs) aided communications, the existing passive beamforming (PB) design involves polynomial complexity in the number of reflecting elements, and thus is difficult to implement due to a massive number of reflecting elements. To overcome this difficulty, we propose a reflection-angle-based cascaded channel model by adopting the generalized Snell's law, in which the dimension of the variable space involved in optimization is significantly reduced, resulting in a simplified hierarchical passive beamforming (HPB) design. We develop an efficient two-stage HPB…
A reconfigurable intelligent surface (RIS) enhanced non-orthogonal multiple access assisted backscatter communication (RIS-NOMABC) system is considered. A joint optimization problem over power reflection coefficients and phase shifts is formulated. To solve this non-convex problem, a low complexity algorithm is proposed by invoking the alternative optimization, successive convex approximation and manifold optimization algorithms. Numerical results corroborate that the proposed RIS-NOMABC system outperforms the conventional non-orthogonal multiple access assisted backscatter communication (NOMA…
In this paper, we analyze the error probability of reconfigurable intelligent surfaces (RIS)-enabled communication systems with quantized channel phase compensation over Rayleigh fading channels. The probability density and characteristic functions of the received signal amplitude are derive dand used to compute exact expressions for the bit error rate(BER). The resulting expressions are general, as they hold for an arbitrary number of reflecting elements N, and quantization levels, L. We introduce an exact asymptotic analysis in the high signal-to-noise ratio (SNR) regime, from which we demon…
We investigate a multi-user multiple-input multiple-output interference network in the presence of multiple reconfigurable intelligent surfaces (RISs). The entire system is described by using a circuit-based model for the transmitters, receivers, and RISs. This is obtained by leveraging the electromagnetic tool of mutual impedances, which accounts for the signal propagation and the mutual coupling among closely-spaced scattering elements. An iterative and provably convergent optimization algorithm that maximizes the sum-rate of RIS-assisted multi-user interference channels is introduced. Numer…
This paper investigates the maximal achievable rate for a given average error probability and blocklength for the reconfigurable intelligent surface (RIS) assisted multiple-input and multiple-output (MIMO) system. The result consists of a finite blocklength channel coding achievability bound and a converse bound based on the Berry-Esseen theorem, the Mellin transform and the mutual information. Numerical evaluation shows fast speed of convergence to the maximal achievable rate as the blocklength increases and also proves that the channel variance is a sound measurement of the backoff from the …
Reconfigurable intelligent surface (RIS)-based transmission technology offers a promising solution to enhance wireless communication performance cost-effectively through properly adjusting the parameters of a large number of passive reflecting elements. This letter proposes a cosine similarity theorem-based low-complexity algorithm for adapting the phase shifts of an RIS that assists a multiple-input multiple-output (MIMO) transmission system. A semi-analytical probabilistic approach is developed to derive the theoretical average bit error probability (ABEP) of the system. Furthermore, the val…
Cooperative rate splitting (CRS), built upon rate splitting multiple access (RSMA) and opportunistic user relaying, has been recognized as a promising transmission strategy to enhance the user fairness and spectral efficiency in multiantenna broadcast channels. To further boost its performance, the interplay of CRS and reconfigurable intelligent surface (RIS) is investigated in this work. Specifically, a novel RIS-aided CRS transmission framework is proposed and the corresponding resource allocation problem to maximize the minimum rate among users is investigated. An alternative optimization a…
We propose a novel reconfigurable intelligent surface (RIS) encoded information transmission scheme for a line-of-sight environment. A RIS fed with data modulates the information on impinging waves emitted from an external source in the states of polarization (SoP) of the scattered waves by performing a novel differential polarization shift keying. In particular, the information is encoded in the change of the SoP over two successive scattering slots. The proposed scheme is immune to the SoP fluctuations in the wireless channel which allows for non-coherent detection at the receiver.
In this letter, we investigate joint application of reconfigurable intelligent surface (RIS) and vertical beamforming in cognitive radio networks (CRN). After properly modeling the network, an optimization problem is formed to jointly design the beamforming vector and tilt angle at the secondary base station (BS) as well as the phase shifts at the RIS with the objective of maximizing spectral efficiency of the secondary network. The optimization problem is non-convex; thus, we propose an efficient solution method for it. Numerical results show that adding a RIS and optimizing the radiation ori…
What is a reconfigurable intelligent surface? What is a smart radio environment? What is a metasurface? How do metasurfaces work and how to model them? How to reconcile the mathematical theories of communication and electromagnetism? What are the most suitable uses and applications of reconfigurable intelligent surfaces in wireless networks? What are the most promising smart radio environments for wireless applications? What is the current state of research? What are the most important and challenging research issues to tackle? These are a few of the many questions that we investigate in this …
The performance of cooperative ambient backscatter communications (CABC) can be enhanced by employing reconfigurable intelligent surface (RIS) to assist backscatter transmitters. Since the RIS power consumption is a non-negligible issue, we consider a RIS assisted CABC system where the RIS with energy harvesting circuit can not only reflect signal but also harvest wireless energy. We study a transmission design problem to minimize the RIS power consumption with the quality of service constraints for both active and backscatter transmissions. The optimization problem is a mixed-integer non-conv…
This paper exploits the potential of reconfigurable intelligent surface (RIS) to improve radar sensing in a non-orthogonal multiple access (NOMA) empowered integrated sensing and communication (NOMA-ISAC) network. The objective is to maximize the minimum radar beampattern gain by jointly optimizing the active beamforming, power allocation coefficients and passive beamforming. To tackle the formulated non-convex problem, we propose an efficient joint optimization algorithm by invoking alternating optimization, successive convex approximation (SCA) and sequential rank-one constraint relaxation (…
In this paper, we examine the potential for a reconfigurable intelligent surface (RIS) to be powered by energy harvested from information signals. This feature might be key to reap the benefits of RIS technology's lower power consumption compared to active relays. We first identify the main RIS power-consuming components and then propose an energy harvesting and power consumption model. Furthermore, we formulate and solve the problem of the optimal RIS placement together with the amplitude and phase response adjustment of its elements in order to maximize the signal-to-noise ratio (SNR) while …
We propose a novel binary polarization shift keying modulation scheme for a line-of-sight environment by exploiting the polarization control ability of the reconfigurable intelligent surface (RIS). The RIS encodes the information data in terms of the polarization states of either the reflected wave from the RIS or the composite wireless channel between an RF source and receiver. In the first case, polarization mismatch correction becomes essential at the receiver. In the second case, the RIS pre-codes the reflected wave to compensate for the polarization mismatch which allows non-coherent demo…
Enabling mmWave Communications with VCSEL-Based Light-Emitting Reconfigurable Intelligent Surfaces
Aristotle University of Thessaloniki（塞萨洛尼基亚里士多德大学）；University of Ioannina and FORTH（约阿尼纳大学与研究所）；James Watt School of Engineering, University of Glasgow（格拉斯哥大学詹姆斯·瓦特工程学院）
Reconfigurable intelligent surfaces (RIS) have been presented as a solution to realize the concept of smart radio environments, wherein uninterrupted coverage and extremely high quality of service can be ensured. In this paper, assuming that multiple RIS are deployed in the propagation environment, the performance of a cascaded RIS network affected by imperfect phase estimation is evaluated. Specifically, we derive closed-form expressions for the outage probability, the ergodic capacity and the average symbol error probability that can be utilized to evaluate the coverage of the proposed netwo…
The extra degrees of freedom resulting from the consideration of Reconfigurable Intelligent Surfaces (RISs) for smart signal propagation can be exploited for high accuracy localization and tracking. In this paper, capitalizing on a recent RIS hardware architecture incorporating a single receive Radio Frequency (RF) chain for measurement collection, we present a user localization method with multiple RISs. The proposed method includes an initial step for direction estimation at each RIS, followed by maximum likelihood position estimation, which is initialized with a least squares line intersect…
Reconfigurable intelligent surface~(RIS) has drawn a great attention worldwide as it can create favorable propagation conditions by controlling the phase shifts of the reflected signals at the surface to enhance the communication quality. However, the practical RIS only has limited phase shifts, which will lead to the performance degradation. In this letter, we evaluate the performance of an uplink RIS assisted communication system by giving an approximation of the achievable data rate, and investigate the effect of limited phase shifts on the data rate. In particular, we derive the required n…
Reconfigurable intelligent surface (RIS) is an emerging technique employing metasurface to reflect the signal from the source node to the destination node. By smartly reconfiguring the electromagnetic (EM) properties of the metasurface and adjusting the EM parameters of the reflected radio waves, RIS can turn the uncontrollable propagation environment into an artificially reconfigurable space, and thus, can significantly increase the communications capacity and improve the coverage of the system. In this paper, we investigate the far field channel in which the line-of-sight (LOS) propagation i…
To achieve the joint active and passive beamforming gains in the reconfigurable intelligent surface assisted millimeter wave system, the reflected cascade channel needs to be accurately estimated. Many strategies have been proposed in the literature to solve this issue. However, whether the Cramér-Rao lower bound (CRLB) of such estimation is achievable still remains uncertain. To fill this gap, we first convert the channel estimation problem into a sparse signal recovery problem by utilizing the properties of discrete Fourier transform matrix and Kronecker product. Then, a joint typicality bas…
A communication link aided by a Reconfigurable Intelligent Surface (RIS) is studied, in which the transmitter can control the state of the RIS via a finite-rate control link. Prior work mostly assumed a fixed RIS configuration irrespective of the transmitted information. In contrast, this work derives information-theoretic limits, and demonstrates that the capacity is achieved by a scheme that jointly encodes information in the transmitted signal as well as in the RIS configuration. In addition, a novel signaling strategy based on layered encoding is proposed that enables practical successive …
Reconfigurable intelligent surfaces (RISs) consisting of multiple reflective elements are a promising technique to enhance communication quality as they can create favorable propagation conditions. In this letter, we characterize the fundamental relations between the number of reflective elements and the system sum-rate in RIS-assisted multi-user communications. It is known from previous works that the received signal-to-noise ratio~(SNR) can linearly increase with the squared number of RIS reflective elements, but how many elements are sufficient to provide an acceptable system sum-rate still…
Reconfigurable intelligent surfaces (RISs) are regarded as a promising emerging hardware technology to improve the spectrum and energy efficiency of wireless networks by artificially reconfiguring the propagation environment of electromagnetic waves. Due to the unique advantages in enhancing wireless channel capacity, RISs have recently become a hot research topic. In this article, we focus on three fundamental physical-layer challenges for the incorporation of RISs into wireless networks, namely, channel state information acquisition, passive information transfer, and low-complexity robust sy…
Channel modeling is a critical issue when designing or evaluating the performance of reconfigurable intelligent surface (RIS)-assisted communications. Inspired by the promising potential of learning-based methods for characterizing the radio environment, we present a general approach to model the RIS end-to-end equivalent channel using the unsupervised expectation-maximization (EM) learning algorithm. We show that an EM-based approximation through a simple mixture of two Nakagami-$m$ distributions suffices to accurately approximating the equivalent channel, while allowing for the incorporation…
Reconfigurable intelligent surfaces (RISs) are typically used in multi-user systems to mitigate interference among active transmitters. In contrast, this paper studies a setting with a conventional active encoder as well as a passive encoder that modulates the reflection pattern of the RIS. The RIS hence serves the dual purpose of improving the rate of the active encoder and of enabling communication from the second encoder. The capacity region is characterized, and information-theoretic insights regarding the trade-offs between the rates of the two encoders are derived by focusing on the high…
A realistic performance assessment of any wireless technology requires the use of a channel model that reflects its main characteristics. The independent and identically distributed Rayleigh fading channel model has been (and still is) the basis of most theoretical research on multiple antenna technologies in scattering environments. This letter shows that such a model is not physically appearing when using a reconfigurable intelligent surface (RIS) with rectangular geometry and provides an alternative physically feasible Rayleigh fading model that can be used as a baseline when evaluating RIS…
Reconfigurable intelligent surface (RIS)-assisted communication appears as one of the potential enablers for sixth generation (6G) wireless networks by providing a new way to optimize the communication system performance. This paper aims to fill an important gap in the open literature by providing an accurate, source, and widely applicable RIS channel model for mmWave frequencies. Our model is not only applicable in various indoor and outdoor environments but also includes the physical aspects of wireless propagation in the presence of an RIS as well as various practical 5G channel modeling is…
In this paper, we introduce a physics-based analytical characterization of the free-space path-loss of a wireless link in the presence of a reconfigurable intelligent surface. The proposed approach is based on the vector generalization of Green's theorem. The obtained path-loss model can be applied to two-dimensional homogenized metasurfaces, which are made of sub-wavelength scattering elements and that operate either in reflection or transmission mode. The path-loss is formulated in terms of a computable integral that depends on the transmission distances, the polarization of the radio waves,…
The key advantage of successive relaying (SR) networks is their ability to mimic the full-duplex (FD) operation with half-duplex (HD) relays. However, the main challenge that comes with such schemes is the associated inter-relay interference (IRI). In this work, we propose a reconfigurable intelligent surface (RIS)-enhanced SR network, where one RIS is deployed near each of the two relay nodes to provide spatial suppression of IRI, and to maximize the gain of desired signals. The resultant max-min optimization problem with joint phase-shift design for both RISs is first tackled via the semidef…
Reconfigurable intelligent surfaces (RISs) become promising for enhancing non-orthogonal multiple access (NOMA) systems, i.e., enhancing the channel quality and altering the SIC orders. Invoked by stochastic geometry methods, we investigate the downlink coverage performance of RIS-aided multi-cell NOMA networks. We first derive the RIS-aided channel model, concluding the direct and reflecting links. The analytical results demonstrate that the RIS-aided channel model can be closely modeled as a Gamma distribution. Additionally, interference from other cells is analyzed. Lastly, we derive closed…
A two-user downlink network aided by a reconfigurable intelligent surface is considered. The weighted sum signal to interference plus noise ratio maximization and the sum rate maximization models are presented, where the precoding vectors and the RIS matrix are jointly optimized. Since the optimization problem is non-convex and difficult, new approximation models are proposed. The upper bounds of the corresponding objective functions are derived and maximized. Two new algorithms based on the alternating direction method of multiplier are proposed. It is proved that the proposed algorithms conv…
We consider a reconfigurable intelligent surface (RIS)-aided massive multi-user multiple-input multiple-output (MIMO) communication system with transceiver hardware impairments (HWIs) and RIS phase noise. Different from the existing contributions, the phase shifts of the RIS are designed based on the long-term angle informations. Firstly, an approximate analytical expression of the uplink achievable rate is derived. Then, we use genetic algorithm (GA) to maximize the sum rate and the minimum date rate. Finally, we show that it is crucial to take HWIs into account when designing the phase shift…
The advantages of millimeter-wave and large antenna arrays technologies for accurate wireless localization received extensive attentions recently. However, how to further improve the accuracy of wireless localization, even in the case of obstructed line-of-sight, is largely undiscovered. In this paper, the reconfigurable intelligent surface (RIS) is introduced into the system to make the positioning more accurate. First, we establish the three-dimensional RIS-assisted wireless localization channel model. After that, we derive the Fisher information matrix and the Cramer-Rao lower bound for eva…
This paper investigates the performance of reconfigurable intelligent surface (RIS)-aided massive multiple-input multiple-output (MIMO) systems with direct links, and the phase shifts of the RIS are designed based on the statistical channel state information (CSI). We first derive the closed-form expression of the uplink ergodic data rate. Then, based on the derived expression, we use the genetic algorithm (GA) to solve the sum data rate maximization problem. With low-complexity maximal-ratio combination (MRC) and low-overhead statistical CSI-based scheme, we validate that the RIS can still br…
The future of mobile communications looks exciting with the potential new use cases and challenging requirements of future 6th generation (6G) and beyond wireless networks. Since the beginning of the modern era of wireless communications, the propagation medium has been perceived as a randomly behaving entity between the transmitter and the receiver, which degrades the quality of the received signal due to the uncontrollable interactions of the transmitted radio waves with the surrounding objects. The recent advent of reconfigurable intelligent surfaces in wireless communications enables, on t…
The design of feedback channels in frequency division duplex (FDD) systems is a major challenge because of the limited available feedback bits. We consider non-orthogonal multiple access (NOMA) systems that incorporate reconfigurable intelligent surfaces (RISs). In limited feedback RIS-aided NOMA systems, the RIS-aided channel and the direct channel gains should be quantized and fed back to the transmitter. This paper investigates the rate loss of the overall RIS-aided NOMA systems suffering from quantization errors. We first consider random vector quantization for the overall RIS-aided channe…
This article aims to reduce huge pilot overhead when estimating the reconfigurable intelligent surface (RIS) relayed wireless channel. Motivated by the compelling grasp of deep learning in tackling nonlinear mapping problems, the proposed approach only activates a part of RIS elements and utilizes the corresponding cascaded channel estimate to predict another part. Through a synthetic deep neural network (DNN), the direct channel and active cascaded channel are first estimated sequentially, followed by the channel prediction for the inactive RIS elements. A three-stage training strategy is dev…
Reconfigurable intelligent surface-empowered communication (RIS) and sparse code multiple access (SCMA) are promising candidates for future generations of wireless networks. The former enhances the transmission environments, whereas the latter provides a high spectral efficiency transmission. This letter proposes, for the first time, an RIS-assisted uplink SCMA (SCMA-RIS) scheme to improve the conventional SCMA spectrum efficiency. The message passing algorithm (MPA) is utilized and modified to decode the SCMA-RIS transmitted signals. Moreover, a low-complexity decoder for the SCMA-RIS scheme …
Sixth generation (6G) mobile networks may include new passive technologies, such as ambient backscatter communication or the use of reconfigurable intelligent surfaces, to avoid the emission of waves and the corresponding energy consumption. On the one hand, a reconfigurable intelligent surface improves the network performance by adding electronically controlled reflected paths in the radio propagation channel. On the other hand, in an ambient backscatter system, a device, named tag, communicates towards a reader by backscattering the waves of an ambient source (such as a TV tower). However, t…
Reconfigurable intelligent surfaces (RISs) are an emerging technology for future wireless communication. The vast majority of recent research on RIS has focused on system level optimizations. However, developing straightforward and tractable electromagnetic models that are suitable for RIS aided communication modeling remains an open issue. In this paper, we address this issue and derive communication models by using rigorous scattering parameter network analysis. We also propose new RIS architectures based on group and fully connected reconfigurable impedance networks that can adjust not only…
In this paper, we survey state-of-the-art research outcomes in the burgeoning field of reconfigurable intelligent surface (RIS) in view of its potential for significant performance enhancement for next generation wireless communication networks by means of adapting the propagation environment. Emphasis has been placed on several aspects gating the commercially viability of a future network deployment. Comprehensive summaries are provided for practical hardware design considerations and broad implications of artificial intelligence techniques, so are in-depth outlooks on salient aspects of syst…
Reconfigurable Intelligent Surface (RIS) has becoming a useful tool in future wireless communication systems for close-distance communication network. This paper we use Reconfigurable Intelligent Surface (RIS) for downlink multi-user communication designed to improve energy collection performance while satisfying wireless information and Power Transfer (WIPT). The designed system consists of an IRS-assisted system consists of a multi-antenna assisted base station (BS) and two opposite multi-antenna assisted information receiver cooperated (RIS) as energy receiver (ERs) that meets energy collec…
In this paper, we introduce a theoretical framework for analyzing the performance of multi-reconfigurable intelligence surface (RIS) empowered terahertz (THz) wireless systems subject to turbulence and stochastic beam misalignment. In more detail, we extract a closed-form expression for the outage probability that quantifies the joint impact of turbulence and misalignment as well as the effect of transceivers' hardware imperfections. Our results highlight the importance of accurately modeling both turbulence and misalignment when assessing the performance of multi-RIS-empowered THz wireless sy…
The reconfigurable intelligent surface (RIS) has arose an upsurging research interest recently due to its promising outlook in 5G-and-beyond wireless networks. With the assistance of RIS, the wireless propagation environment is no longer static and could be customized to support diverse service requirements. In this paper, we will approach the rate maximization problems in RIS-aided wireless networks by considering the beamforming and reflecting design jointly. Three representative design problems from different system settings are investigated based on a proposed unified algorithmic framework…
In this work, we consider the target detection problem in a sensing architecture where the radar is aided by a reconfigurable intelligent surface (RIS), that can be modeled as an array of sub-wavelength small reflective elements capable of imposing a tunable phase shift to the impinging waves and, ultimately, of providing the radar with an additional echo of the target. A theoretical analysis is carried out for closely- and widely-spaced (with respect to the target) radar and RIS and for different beampattern configurations, and some examples are provided to show that large gains can be achiev…
Recent research provides an approximation on the performance for reconfigurable intelligent surface (RIS) assisted systems over generalized fading channels with phase noise resulting from imperfect phase compensation at the RIS. In this paper, we developed exact analysis and upper bounds on the performance of RIS-assisted vehicular communication system considering phase noise with mobility over asymmetric fading channels by coherently combining received signals reflected by RIS elements and direct transmissions from the source terminal. We employ a novel approach to represent the PDF and CDF o…
We introduce a phase hopping scheme for reconfigurable intelligent surfaces (RISs) in which the phases of the individual RIS elements are randomly varied with each transmitted symbol. This effectively converts slow fading into fast fading. We show how this can be leveraged to significantly improve the outage performance especially for small outage probabilities without channel state information (CSI) at the transmitter and RIS. Furthermore, the same result can be accomplished even if only two possible phase values are available. Since we do not require perfect CSI at the transmitter or RIS, th…
