In the last decades severe plastic deformation techniques have gained increasing interest as they allow the production of bulk nanostructured materials with superior mechanical and functional properties. However, because of mechanically induced grain boundary migration, the achievable grain size reduction is not indefinite but tends to stagnate once sufficient strain has been applied. Consequently, addition of solute elements or second phase particles offers the possibility to access the true nanocrystalline regime. Due to their low solubility and high mobility, interstitial elements are extremely effective at subduing boundary migration. Herein the effect of carbon on grain refinement and the resulting mechanical properties are summarized. As carbon may not only be added as graphite but could also be introduced in other forms or as allotropes such as nanotubes, nanodiamonds, or carbides, the respective advantages and problems associated with it are the center of discussion. Independent of the strategy used, strength levels hardly achievable with other alloying elements can be obtained. Moreover, as carbon does not have a negative effect on grain boundary cohesion, despite the enormous strength levels even ductility and toughness can be widely maintained.
By introducing a strain rate generated pseudo-electric field, we discuss a magnetic response of a plastically deformed graphene. Our results demonstrate the appearance of dislocation induced paramagnetic moment in a zero applied magnetic field. More interestingly, it is shown that in the presence of the magnetoplastic effect, the resulting magnetization exhibits typical features of the so-called fishtail anomaly (previously observed in superconductors). The estimates of the model parameters suggest quite an optimistic possibility to experimentally realize the predicted phenomena in plastically…
Cementite Fe3C is studied with first-principles calculations. Two possible positions of carbon atoms in the iron sublattice are considered: with prismatic or octahedral environment. Mossbauer spectra (MS) with parameters calculated for both modifications are simulated above and below the Curie temperature. A possibility to detect the change in carbon position upon annealing from MS is discussed. It is shown that this is hardly possible using a standard approach to treatment of MS, but it can be seen in more subtle details of the MS below the Curie temperature, such as widths and positions of s…
Nanocrystalline materials are well known for their beneficial mechanical and physical properties. However, it is of utmost importance to stabilize the microstructure at elevated temperatures to broaden the window of application e.g. by pinning grain boundaries through impurities or oxides. CuCo alloys, severe plastically deformed using high-pressure torsion, were used to investigate the evolution of oxides upon annealing. These investigations were performed using electron microscopy, synchrotron high-energy X-ray scattering and atom probe tomography. Monitoring the evolution of oxides by in-si…
Previous experimental studies of the thermal conductivity of plastically deformed lead crystals in the superconducting state have shown strong anomalies in the thermal conductivity. Similar effects were also found for the thermal conductivity of bent ${}^4\text{He}$ samples. Until now, a theoretical explanation for these results was missing. In this paper we will introduce the process of phonon-kink scattering and show that it qualitatively explains the anomalies that experiments had found.
We present a numerical study of a continuum plasticity field coupled to a Ginzburg-Landau model for superfluidity. The results suggest that a supersolid fraction may appear as a long-lived transient during the time evolution of the plasticity field at higher temperatures where both dislocation climb and glide are allowed. Supersolidity, however, vanishes with annealing. As the temperature is decreased, dislocation climb is arrested and any residual supersolidity due to incomplete annealing remains frozen. Our results provide a resolution of many perplexing issues concerning a variety of experi…
We analyze the surface morphology of metals after plastic deformation over a range of scales from 10 nm to 2 mm, using a combination of atomic force microscopy and scanning white-light interferometry. We demonstrate that an initially smooth surface during deformation develops self-affine roughness over almost four orders of magnitude in scale. The Hurst exponent $H$ of one-dimensional surface profiles is initially found to decrease with increasing strain and then stabilizes at $H \approx 0.75$. By analyzing their statistical properties we show that the one-dimensional surface profiles can be m…
The contribution to the low frequency internal friction and the thermal conductivity due to optically vibrating edge dislocation dipoles is calculated within the modified Granato-Lucke string model. The results are compared with the recent experiments on plastically deformed samples of Al, Ta and Nb at low temperatures. It is shown that the presence of a reasonable density of optically vibrating dislocation dipoles provides a good fit to the thermal conductivity in superconducting samples. At the same time, the internal friction experiments can not be described within the standard fluttering s…
Recent experiments (Le Bouil et al., Phys. Rev. Lett., 2014, 112, 246001) have analyzed the statistics of local deformation in a granular solid undergoing plastic deformation. Experiments report strongly anisotropic correlation between events, with a characteristic angle that was interpreted using elasticity theory and the concept of Eshelby transformations with dilation; interestingly, the shear bands that characterize macroscopic failure occur at an angle that is different from the one observed in microscopic correlations. Here, we interpret this behavior using a mesoscale elastoplastic mode…
The properties of quantum materials are commonly tuned using experimental variables such as pressure, magnetic field and doping. Here we explore a different approach: irreversible, plastic deformation of single crystals. We show for the superconductor SrTiO$_3$ that compressive plastic deformation induces low-dimensional superconductivity significantly above the superconducting transition temperature ($T_c$) of undeformed samples, with evidence of superconducting correlations at temperatures two orders of magnitude above the bulk $T_c$. The superconductivity enhancement is correlated with the …
We present experimental and theoretical results for the surface topography of a plastically deformed metallic (aluminum) block. When a hard spherical body (here a steel-, silica glass- or silicon nitride ball) with a smooth surface is indented in a metal block with a nominally flat, but still rough, surface, a spherical-cup-like indentation result due to plastic flow. The surface roughness in the indented region is, however, not entirely flattened. The long wavelength (macroasperity) content of the roughness result from the roughness on the original (aluminum) surface, but now plastically defo…
Grain boundary diffusion in severely deformed Al-based AA5024 alloy is investigated. Different states are prepared by combination of equal channel angular processing and heat treatments, with the radioisotope $^{57}$Co being employed as a sensitive probe of a given grain boundary state. Its diffusion rates near room temperature (320~K) are utilized to quantify the effects of severe plastic deformation and a presumed formation of a previously reported deformation-modified state of grain boundaries, solute segregation at the interfaces, increased dislocation content after deformation and of the …
Al/Ni multilayers have been prepared by repeated folding and cold rolling (F&R) of elemental foils. The thickness of Al and Ni foils is reduced down to less than 50 nm after fifty F&R cycles. Three-dimensional atom probe analyses clearly reveal the presence of supersaturated solid solutions and give the evidence of deformation-induced intermixing. The formation of the solid solutions and their transformation into the Al3Ni phase upon annealing is discussed.
Mixtures of Fe and Cu powders are cold-compacted and subsequently deformed with severe plastic deformation by high-pressure torsion, leading to bulk samples. The dilution of Fe in the Cu matrix is investigated with SQUID-magnetometry, whereas the magnetic properties change as a function of Fe-content from a frustrated regime to a thermal activated behaviour. The magnetic properties are correlated with the microstructure, investigated by synchrotron X-ray diffraction and atom probe tomography. Annealing of the as-deformed states leads to demixing and grain growth, with the coercivity as a funct…
In the Cu Cr system, the formation of supersaturated solid solutions can be obtained by severe plastic deformation. Energy dispersive synchrotron diffraction measurements on as deformed Cu Cr samples as a function of the applied strain during deformation confirm the formation of supersaturated solid solutions in this usually immiscible system. Due to evaluation of the diffraction data by a newly developed energy dispersive Rietveld program, lattice parameter and microstructural parameters such as domain size and microstrain are determined for as deformed as well as annealed samples. The obtain…
The processing of binary alloys consisting of ferromagnetic Fe and antiferromagnetic Cr by severe plastic deformation (SPD) with different chemical compositions has been investigated. Although the phase diagram exhibits a large gap in the thermodynamical equilibrium at lower temperatures, it is shown that techniques based on SPD help to overcome common processing limits. Different processing routes including initial ball milling (BM) and arc melting (AM) and a concatenation with annealing treatments prior to high-pressure torsion (HPT) deformation are compared in this work. Investigation of th…
A FePd alloy was nanostructured by severe plastic deformation following two different routes: ordered and disordered states were processed by high pressure torsion (HPT). A grain size in a range of 50 to 150 nm is obtained in both cases. Severe plastic deformation induces some significant disordering of the long range ordered L10 phase. However, Transmission Electron Microscopy (TEM) data clearly show that few ordered nanocrystals remain in the deformed state. The deformed materials were annealed to achieve nanostructured long range ordered alloys. The transformation proceeds via a first order…
The properties of bulk nanostructured materials are often controlled by atomic scale features like segregation along defects or composition gradients. Here we discuss about the complimentary use of TEM and APT to obtain a full description of nanostructures. The advantages and limitations of both techniques are highlighted on the basis of experimental data collected in severely deformed steels with a special emphasis on carbon spatial distribution.
A Cu-Cr composite was processed by severe plastic deformation to investigate the role of interphase boundaries on the grain size reduction mechanisms. The as-deformed material exhibits a grain size of only 20nm. This gives rise to a dramatic increase of the hardness. Some deformation induced Cu super saturated solid solutions were clearly exhibited and it is shown that they decrease the hardness. The formation of such supersaturated solid solution and their influence on the mechanical properties are discussed.
A variety of severe plastic deformation (SPD) techniques have been developed to process materials to high strains and impart microstructural refinement. High pressure torsion (HPT) is one technique that imparts inhomogeneous strain to process discs with low strain in the center and high strain at the outer edge. In the literature, this inhomogeneity is typically ignored when characterizing wear properties after HPT. In this work, the wear rate of pure copper discs processed by HPT was characterized by conducting dry sliding reciprocating wear tests at a few judicious locations on the discs. Fr…
This work gives insights into processing and characterisation of bulk nanocrystalline FeCr materials. The investigated FeCr alloys, consisting of 30, 50 and 70 at.% ferromagnetic Fe and remaining anti-ferromagnetic Cr, are processed by arc melting and subsequent severe plastic deformation by high pressure torsion. The physical similarities between elemental Fe and Cr in combination with the nanocrystalline structure of the as-deformed alloys, necessitates advanced characterisation techniques for the as-deformed state: In-situ annealing synchrotron X-ray diffraction measurements as well as elec…
The image fractal analysis is actively used in all science branches. In particular in materials science the fractal analysis is applied to study microstructure of deformed metals because its structure can be interpreted as the fractal image. It is well known that such images can be described by fractal dimension. In this paper, the fractal dimension change for different kinds of metals in the processes of severe plastic deformation (SPD) is explored. It is shown that for the undeformed metals the stochastic network of structural elements boundaries has the fractal dimension Db=1.60\pm 0.03. Th…
Grain boundary segregations were investigated by Atom Probe Tomography in an Al-Mg alloy, a carbon steel and Armco\trademark Fe processed by severe plastic deformation (SPD). In the non-deformed state, the GBs of the aluminium alloy are Mg depleted, but after SPD some local enrichment up to 20 at.% was detected. In the Fe-based alloys, large carbon concentrations were also exhibited along GBs after SPD. These experimental observations are attributed to the specific structure of GBs often described as "non-equilibrum" in ultra fine grained materials processed by SPD. The grain boundary segregat…
Exchange-coupling between soft- and hard-magnetic phases plays an important role in the engineering of novel magnetic materials. To achieve exchange coupling, a two-phase microstructure is necessary. This interface effect is further enhanced if both phase dimensions are reduced to the nanometer scale. At the same time, it is challenging to obtain large sample dimensions. In this study, powder blends and ball-milled powder blends of Fe-SmCo$_{5}$ are consolidated and are deformed by high-pressure torsion (HPT), as this technique allows us to produce bulk magnetic materials of reasonable sizes. …
Cu-refractory metal composites containing Cr, Mo or W were subjected to severe plastic deformation using room temperature high-pressure torsion (HPT). A lamellar microstructure developed in each of the composites at equivalent strains of ~75. The refractory metals developed {hkl}<111> fibre textures with a slight tilt to the tangential direction. This texture was stronger and more clearly defined in Mo and W than in Cr. By applying additional HPT deformation to these samples, perpendicular to the original shear strain, it was found that the lamellar structure of Cu30Mo70 and Cu20W80 (wt.%) com…
Knowledge of the state of plastic deformation in metallic structures is vital to prevent failure. This is why non-destructive acoustic tests based on the measurement of first order elastic constants have been developed and intensively used. However, plastic deformations, which are usually heterogeneous in space, may be invisible to these methods if the variation of the elastic constants is too small. In recent years, digital image correlation techniques, based on measurements carried out at the surface of a sample, have been successfully used in conjunction with finite element modeling to gain…
A complex study of aging kinetics for both coarse-grained and nanostructured by severe plastic deformation Cu -- 2 wt% Be alloy is reported. It is shown that aging of a coarse-grained alloy leads to continuous formation of nanosized CuBe body centred cubic (bcc, CsCl -- type) semi-coherent particles with the {220} Cu // {200} CuBe crystallographic orientation relationship. These particles created significant internal stress fields and became obstacles for dislocation glide that resulted in a change in the hardness from 95 Vickers hardness (HV) for the solubilized alloy to 400 HV for the aged o…
An elastic membrane that is forced to reside in a container smaller than its natural size will deform and, upon further volume reduction, eventually crumple. The crumpled state is characterized by the localization of energy in a complex network of highly deformed crescent-like regions joined by line ridges. Previous studies have focused on the onset of the crumpled state by analyzing the mechanical response and stability of a conical dislocation, while others have simulated the highly packed regime neglecting the importance of the connectivity of the membrane. Here we show, through a combinati…
High-pressure torsion (HPT), a technique of severe plastic deformation (SPD), is shown as a promising processing method for exchange-spring magnetic materials in bulk form. Powder mixtures of Fe and SmCo$_{5}$ are consolidated and deformed by HPT exhibiting sample dimensions of several millimetres, being essential for bulky magnetic applications. The structural evolution during HPT deformation of Fe-SmCo$_{5}$ compounds at room- and elevated- temperatures of chemical compositions consisting of 87, 47, 24 and 10 wt.% Fe is studied and microstructurally analysed. Electron microscopy and synchrot…
Nanodiamond reinforced silver matrix nanocomposites with different nanodiamond content are produced from pure silver and nanodiamond powders by a combination of two severe plastic deformation methods, ball-milling and high-pressure torsion (HPT). The ball milling parameters are varied to improve the distribution of the nanodiamonds in the powder blends. An optimized processing route combining both processes has been developed to achieve a homogenous dispersion of small nanodiamond particles in a nanocrystalline silver matrix. The microstructure of these nanocomposites was characterized by scan…
Achieving a combination of high mechanical strength and high electrical conductivity in low-weight Al alloys requires a full understanding of the relationships between nanoscaled features and physical properties. Grain boundary strengthening through grain size reduction offers some interesting possibilities but is limited by thermal stability issues. Zener pinning by stable nanoscaled particles or grain boundary segregation are well-known strategies for stabilizing grain boundaries. In this study, the Al-Ca system has been selected to investigate the way segregation affects the combination of …
