Electro-optic frequency combs were employed to rapidly interrogate an optomechanical sensor, demonstrating spectral resolution substantially exceeding that possible with a mode-locked frequency comb. Frequency combs were generated using an integrated-circuit-based direct digital synthesizer and utilized in a self-heterodyne configuration. Unlike approaches based upon laser locking or sweeping, the present approach allows rapid, parallel measurements of full optical cavity modes, large dynamic range of sensor displacement, and acquisition across a wide frequency range between DC and 500 kHz. In addition to being well suited to measurements of cavity optomechanical sensors, this optical frequency comb-based approach can be utilized for interrogation in a wide range of physical and chemical sensors.
An interleaved, chirped electro-optic dual comb system is demonstrated for rapid, high dynamic range measurements of cavity optomechanical sensors. This approach allows for the cavity displacements to be interrogated at measurement times as fast as 10 μs over ranges far larger than can be achieved with alternative methods. While the performance of this novel readout approach is evaluated with an optomechanical accelerometer, this method is applicable to a wide range of applications including temperature, pressure, and humidity sensing as well as acoustics and molecular spectroscopy.
Combination of dissipative and dispersive coupling in the cavity optomechanical systems
Faculty of Physics, M.V. Lomonosov Moscow State University（莫斯科国立大学物理系）；Quantum Technology Centre, M.V. Lomonosov Moscow State University（莫斯科国立大学量子技术中心）
We demonstrate a microfabricated optomechanical accelerometer that is capable of percent-level accuracy without external calibration. To achieve this capability, we use a mechanical model of the device behavior that can be characterized by the thermal noise response along with an optical frequency comb readout method that enables high sensitivity, high bandwidth, high dynamic range, and SI-traceable displacement measurements. The resulting intrinsic accuracy was evaluated over a wide frequency range by comparing to a primary vibration calibration system and local gravity. The average agreement…
We observe high optical quality factor (Q) polygonal and star coherent optical modes in a lithium niobate microdisk. In contrast to the previous polygon modes achieved by deformed microcavities at lower mechanical and optical Q, we adopted weak perturbation from a tapered fiber for the polygon mode formation. The resulting high intracavity optical power of the polygon modes triggers second harmonic generation at high efficiency. With the combined advantage of high mechanical Q cavity optomechanical oscillation was observed for the first time. Finally, we observe frequency microcomb generation …
Optomechanical devices operated at their quantum limit open novel perspectives for the ultrasensitive determination of mass and displacement, and also in the broader field of quantum technologies. The access to higher frequencies implies operation at higher temperatures and stronger immunity to environmental noise. We propose and demonstrate here a new concept of quantum well photoelastic comb for the efficient coupling of light to optomechanical resonances at hundreds of GHz in semiconductor hybrid resonators. A purposely designed ultra-high resolution Raman spectroscopy set-up is exploited t…
Cavity optomechanics has become a powerful tool to manipulate mechanical motion via optical fields. When driving an optomechanical cavity with blue-detuned laser the mechanical motion is amplified, ultimately resulting in phonon lasing. In this work, we show that a silicon optomechanical crystal cavity can be used as an optoelectronic oscillator when driven to the phonon lasing condition. To this end, we use an optomechanical cavity designed to have a breathing-like mechanical mode vibrating at $Ω_{m}/2π=$3.897 GHz in a full phononic bandgap. Our measurements show that the first harmonic displ…
Frequency comb generation in active optomechanical cavities
Sri Guru Tegh Bahadur Khalsa College, University of Delhi（德里大学斯里古鲁泰格·巴哈杜尔·卡尔萨学院）；Birla Institute of Technology and Science Pilani, Dubai Campus（比拉理工学院迪拜校区）
We discuss the design of quantum hybrid inertial sensor that combines an optomechanical inertial sensor with the retro-reflector of a cold atom interferometer. This sensor fusion approach provides absolute and high accuracy measurements with cold atom interferometers, while utilizing the optomechanical inertial sensor at frequencies above the repetition rate of the atom interferometer. This improves the overall measurement bandwidth as well as the robustness and field deployment capabilities of these systems. We evaluate which parameters yield an optimal acceleration sensitivity, from which we…
Phonons offer the possibility to connect the microwave and optical domains while being efficiently transduced with electronic and optical signals. Here, we present a multimodal optomechanical platform, consisting of a mechanical-optical-mechanical resonator configuration. The mechanical modes, with frequencies at 265 MHz and 6.8 GHz, can be simultaneously excited into a phonon lasing regime as supported by a stability analysis of the system. Both the MHz and the GHz modes enter a self-sustained oscillation regime, leading to the intermodulation of two frequency combs in the optical field. We c…
We describe an apparatus for the implementation of hybrid optomechanical systems at 4 K. The platform is based on a high-finesse, micrometer-scale fiber Fabry-Perot cavity, which can be widely tuned using piezoelectric positioners. A mechanical resonator can be positioned within the cavity in the object-in-the-middle configuration by a second set of positioners. A high level of stability is achieved without sacrificing either performance or tunability, through the combination of a stiff mechanical design, passive vibration isolation, and an active Pound-Drever-Hall feedback lock incorporating …
In this work, we proposed a high resolution D-shaped photonic crystal fiber (PCF) surface plasmon resonance (SPR) sensor based on gold grating. Gold grating is introduced to modulate the resonance wavelength and enhance the refractive index (RI) sensitivity. Structure parameters of PCF and gold grating are analyzed by finite element method (FEM) for optimizing the SPR sensor. The simulation results indicate that air hole pitch, air hole diameter and gold thickness and grating constant have little influence on the sensitivity of refractive index, which reduces the requirement of precise process…
Collective phenomena emerging from non-linear interactions between multiple oscillators, such as synchronization and frequency locking, find applications in a wide variety of fields. Optomechanical resonators, which are intrinsically non-linear, combine the scientific assets of mechanical devices with the possibility of long distance controlled interactions enabled by travelling light. Here we demonstrate light-mediated frequency locking of three distant nano-optomechanical oscillators positioned in a cascaded configuration. The oscillators, integrated on a chip along a coupling waveguide, are…
Cavity optomechanical system can exhibit higher-order sideband comb effect when it is driven by a control field $ω_{c}$ and a probe field $ω_{p}$, and works in the non-perturbative regime, as was shown in a previous work [Xiong et al., Opt. Lett. 38, 353 (2013)]. The repetition frequency of such a comb is equal to the mechanical frequency $ω_{b}$ and is untunable, which limits the precision of the comb. Here we address this problem by driving the system with an additional strong probe field $ω_{f}$, and the detuning between $ω_{f}$ and $ω_{c}$ is equal to $ω_{b}/n$ (here $n$ is an integer), i.…
Soliton microcombs based on Kerr nonlinearity in microresonators have been a prominent miniaturized coherent light source. Here, for the first time, we demonstrate the existence of Kerr solitons in an optomechanical microresonator, for which a nonlinear model is built by incorporating a single mechanical mode and multiple optical modes. Interestingly, an exotic vibrational Kerr soliton state is found, which is modulated by a self-sustained mechanical oscillation. Besides, the soliton provides extra mechanical gain through the optical spring effect, and results in phonon lasing with a red-detun…
Optomechanical systems combine extreme sensitivity and bandwidth in the control of mechanical motion, of interest for various applications. Integrated on a chip, actuated and detected all-optically by a single laser, they could disrupt sensing technologies. We introduce here a multiphysics model that describes their operation in the oscillating mode, under sinusoidal modulation of the laser, when both photothermal forces and radiation pressure are present, and when nonlinear absorption occurs in the device. The model is validated by systematic experiments on ultra-high frequency optomechanical…
Integrated optomechanical cavities stand as a promising means to interface mechanical motion and guided optical modes. State-of-the-art demonstrations rely on optical and mechanical modes tightly confined of in micron-scale areas to achieve strong optomechanical coupling. However, the need for tight optomechanical confinement and the general use of suspended devices hinders interaction with external devices, limiting the potential for the implementation of complex circuits. Here, we propose and demonstrate a new approach for optomechanical cavities coupling free-propagating surface acoustic wa…
Gallium phosphide offers an attractive combination of a high refractive index ($n>3$ for vacuum wavelengths up to 4 μm) and a wide electronic bandgap (2.26 eV), enabling optical cavities with small mode volumes and low two-photon absorption at telecommunication wavelengths. Heating due to strongly confined light fields is therefore greatly reduced. Here, we investigate the benefits of these properties for cavity optomechanics. Utilizing a recently developed fabrication scheme based on direct wafer bonding, we realize integrated one-dimensional photonic crystal cavities made of gallium phosphid…
It is quite important to enhance and control the optomechanically induced high-order sideband generation to achieve low-power optical comb and high-sensitivity sensing with an integratable structure. Here we present and analyze a proposal for enhancement and manipulation of optical nonlinearity and high-order sideband generation in a hybrid atom-cavity optomechanical system that is coherently driven by a bichromatic input field consisting of a control field and a probe field and works beyond the perturbative regime. Our numerical analysis with experimentally achievable parameters confirms that…
We report on the modification of the optical and mechanical properties of a silicon 1D optomechanical crystal cavity due to thermo-optic effects in a high phonon/photon population regime. The cavity heats up due to light absorption in a way that shifts the optical modes towards longer wavelengths and the mechanical modes to lower frequencies. By combining the experimental optical results with finite-difference time-domain simulations we establish a direct relation between the observed wavelength drift and the actual effective temperature increase of the cavity. By assuming that the Young's mod…
We develop a rigorous theoretical framework for interaction-induced phenomena in the waveguide quantum electrodynamics (QED) driven by mechanical oscillations of the qubits. Specifically, we predict that the simplest set-up of two qubits, harmonically trapped over an optical waveguide, enables the ultrastrong coupling regime of the quantum optomechanical interaction. Moreover, the combination of the inherent open nature of the system and the strong optomechanical coupling leads to emerging parity-time (\PT) symmetry, quite unexpected for a purely quantum system without artificially engineered …
In this paper we propose a novel strategy to control optomechanical parametric instability (PI) in gravitational wave (GW) detectors, based on radiation pressure. The fast deflection of a high power beam is the key element of our approach. We built a 2D deflection system based on a pair of acousto-optic modulators (AOMs) that combines high rapidity and large scan range. As fast frequency switching configurable AOM driver we used an Universal Software Radio Peripheral (USRP) combined with a high performance personal computer (PC). In this way we demonstrate a 2D beam steering system with flat e…
In the field of cavity nano-optomechanics, the nanoresonator-in-the-middle approach consists in inserting a sub-wavelength sized deformable resonator, here a nanowire, in the small mode volume of a fiber microcavity. Internal resonances in the nanowire enhance the light nanowire interaction which provide giant coupling strengthes -- sufficient to enter the single photon regime of cavity optomechanics -- at the condition to precisely position the nanowire within the cavity field. Here we expose a theoretical description that combines an analytical formulation of the Mie-scattering of the intrac…
Laser cooling of mechanical degrees of freedom is one of the most significant achievements in the field of opto-mechanics. Here, we report, for the first time to the best of our knowledge, efficient passive optomechanical cooling of the motion of a freestanding waveguide coupled to a whispering-gallery-mode (WGM) resonator. The waveguide is an 8 mm long glass-fiber nanospike, which has a fundamental flexural resonance at Ω/2π = 2.5 kHz and a Q-factor of 1.2 10**5. Upon launching 250 μW laser power at an optical frequency close to the WGM resonant frequency, we observed cooling of the nanospike…
Laser engineered exciton-polariton networks could lead to dynamically configurable integrated optical circuitry and quantum devices. Combining cavity optomechanics with electrodynamics in laser configurable hybrid designs constitutes a platform for the vibrational control, conversion, and transport of signals. With this aim we investigate 3D optical traps laser-induced in quantum-well embedded semiconductor planar microcavities. We show that the laser generated and controlled discrete states of the traps dramatically modify the interaction between photons and phonons confined in the resonators…
A III-V compound semiconductor nanowire is an attractive material for a novel hybrid quantum interface that interconnects photons, electrons, and phonons through a wavelength-tunable quantum structure embedded in its free-standing structure. In such a nanomechanical element, however, a challenge is how to detect and manipulate a small number of phonons via its tiny mechanical motion. A solution would be to couple an optical cavity to a nanowire by introducing the ``cavity optomechanics'' framework, but the typical size difference between them becomes a barrier to achieving this. Here, we demon…
Optomechanical transducers for gigahertz frequency ultrasound imaging
Sandia National Laboratories（桑迪亚国家实验室）；James C. Wyant College of Optical Sciences, University of Arizona（亚利桑那大学詹姆斯·C·怀安特光学学院）；Electrical, Computer and Energy Engineering, University of Colorado, Boulder（科罗拉多大学博尔德分校电气、计算机与能源工程学院）
Efficient interconversion of both classical and quantum information between microwave and optical frequency is an important engineering challenge. The optomechanical approach with gigahertz-frequency mechanical devices has the potential to be extremely efficient due to the large optomechanical response of common materials, and the ability to localize mechanical energy into a micron-scale volume. However, existing demonstrations suffer from some combination of low optical quality factor, low electrical-to-mechanical transduction efficiency, and low optomechanical interaction rate. Here we demon…
Photonic crystal (PhC) membranes patterned with sub-wavelength periods offer a unique combination of high reflectivity, low mass, and high mechanical quality factor. We demonstrate a PhC membrane that we use as one mirror of a Fabry-Perot cavity with finesse as high as $F=35,000(500)$, corresponding to a record high PhC reflectivity of $R=0.999835(6)$. The fundamental mechanical frequency is 426 kHz, more than twice the optical linewidth, placing it firmly in the resolved-sideband regime. The mechanical quality factor in vacuum is $Q=1.1(1)\times 10^6$, allowing us to achieve values of the sin…
