Photonic sensors based upon high-quality optical microcavities have found a wide variety of applications ranging from inertial sensing, electro- and magnetometry to chemical and biological sensing. These sensors have a dynamic range limited by the linewidth of the cavity mode transducing the input. This dynamic range not only determines the range of the signal strength that can be detected, but also affects the resilience of the sensor to large deteriorating external perturbations and shocks in a practical environment. Unfortunately, there is a general trade-off between the detection sensitivity and the dynamic range, which undermines the performance of all microcavity-based sensors. Here we propose an approach to extend the dynamic range significantly beyond the cavity linewidth limit, in the nonlinear modulation regime, without degrading the detection sensitivity for weak signals. With a cavity optomechanical system, we experimentally demonstrate a dynamic range six times larger than the cavity linewidth, far beyond the conventional linear region of operation for such a sensor. The approach demonstrated here will help design microcavity-based sensors to achieve high detection sensitivity and a large dynamic range at the same time, a crucial property for their use in a practical environment.
A fully on-fiber optomechanical cavity is fabricated by patterning a suspended metallic mirror on the tip of an optical fiber. Optically induced self-excited oscillations of the suspended mirror are experimentally demonstrated. We discuss the feasibility of employing on-fiber optomechanical cavities for sensing applications. A theoretical analysis evaluates the sensitivity of the proposed sensor, which is assumed to operate in the region of self-excited oscillations, and the results are compared with the experimental data. Moreover, the sensitivity that is obtained in the region of self-excite…
We present a novel locking scheme for active length-stabilization and frequency detuning of a cavity optomechanical device based on the optical spring effect. The scheme can be used as an alternative to the Pound-Drever-Hall locking technique but in contrast doesn't require signal processing on time-scales of the cavity decay rate. It is therefore particularly suited for stabilizing micro cavities, where this time-scale can be extremely fast. The error signal is generated through the optical spring effect, i.e. the detuning-dependent frequency-shift of a nanomechanical oscillator that is dispe…
In cavity optomechanics, nonlinear interactions between an optical field and a mechanical resonator mode enable a variety of unique effects in classical and quantum measurement and information processing. Here, we describe nonlinear optomechanical coupling in the membrane-in-the-middle (MIM) setup in a way that allows direct comparison to the intrinsic optomechanical nonlinearity in a standard, single-cavity optomechanical system. We find that the enhancement of nonlinear optomechanical coupling in the MIM system as predicted by Ludwig et al. arXiv:1202.0532 is limited to the degree of sideban…
We theoretically demonstrate complete all-optical control of light group velocity via a cavity optomechanical system composed of an optical cavity and a mechanical resonator. The realization depends on no specific materials inside the cavity, and the control of light group velocity stems from the interaction between the signal light and the moving optical diffraction grating within the cavity in analogy to the stimulated Brillouin scattering(SBS). Furthermore, we show that a tunable switch from slow light to fast light can be achieved only by simply adjusting the pump-cavity detuning. The sche…
We study entanglement of the cavity modes in a double-cavity optomechanical system in strong-coupling regime. The system consists of two optomechanical systems coupled by a single photon hopping between them. With the radiation pressure of the photon, entanglement of the cavity modes can be generated. The concurrence between the cavity modes is at least twice larger than that between the mechanical modes. Moreover, when we change the ratio between coupling strength and resonant frequency of mechanical modes, the entanglement in cavity and mechanical modes are influenced differently.
We demonstrate the actuation of a double beam opto-mechanical cavity with a sinusoidally varying optical input power. We observe the driven mechanical motion with only 200 nW coupled to the optical cavity mode. We also investigate the pump power dependence of the radio-frequency response for both the driving power and the probe power. Finally, we investigate the dependence of the amplitude of the mechanical motion on mechanical cavity quality factor.
Sub-femtogram resolution of an in-liquid cavity optomechanical mass sensor based on the twin-microbottle glass resonator is demonstrated. An evaluation of the frequency stability using an optomechanical phase-locked loop reveals that this cavity optomechanical sensor has the highest mass resolution of $(7.0\times2.0)\times 10^{-16}$ g in water, which is four orders of magnitude better than that in our first-generation setup [Sci. Adv. 8, eabq2502 (2022)]. This highly sensitive mass sensor provides a free-access optomechanical probe in liquid and could thus be extended to a wide variety of in-s…
We propose a novel scheme for realizing single-photon blockade in a weakly driven hybrid cavity optomechanical system consisting of a nonlinear photonic crystal. Sub-Poissonian statistics is realized even when the single-photon optomechanical coupling strength is smaller than the decay rate of the optical mode. The scheme relaxes the requirement of strong coupling for photon blockade in optomechanical systems. It is shown that photon blockade could be generated at the telecommunication wavelength.
Periodically structured materials can sustain both optical and mechanical modes. Here we investigate and observe experimentally the optomechanical properties of a conventional two-dimensional suspended photonic crystal defect cavity with a mode volume of $\sim$$3(λ/n)^{3}$. Two families of mechanical modes are observed: flexural modes, associated to the motion of the whole suspended membrane, and localized modes with frequencies in the GHz regime corresponding to localized phonons in the optical defect cavity of diffraction-limited size. We demonstrate direct measurements of the optomechanical…
We report an optomechanical system with two dielectric membranes inside a Fabry-Perot cavity. The cavity resonant frequencies are measured in such a two-membrane-in-the-middle system, which show an interesting band-structure-like diagram. This system exhibits great controllability on the parameters of the system. The positions and angles of each membrane can be manipulated on demand by placing two membranes inside the cavity separately. The eigenfrequencies of the vibrational modes of the membranes can also be tuned individually with piezoelectricity. This scheme could be straightforwardly ext…
Combination of dissipative and dispersive coupling in the cavity optomechanical systems
Faculty of Physics, M.V. Lomonosov Moscow State University（莫斯科国立大学物理系）；Quantum Technology Centre, M.V. Lomonosov Moscow State University（莫斯科国立大学量子技术中心）
A theoretical consideration of the so-called "membrane-in-the-middle" optomechanical cavity revealed that it undergoes a spontaneous symmetry breaking as a function of the transparency of the membrane. Such typical features of this phenomenon as a square-root development of the order parameter and divergency of the critical susceptibility were identified. In the contract to classical spontaneous-symmetry-breaking systems of ferromagnets and ferroelectrics, in the considered system, this divergency remains, due to interference effects, an "internal" property of the system, which does not reveal…
We report narrow linewidth optomechanical oscillation of a silica microsphere immersed in a buffer solution. Through a novel optomechanical transduction sensing approach, single 10-nm-radius silica beads and Bovine serum albumin (BSA) protein molecules with a molecular weight of 66 kDalton were detected. This approach predicts the detection of 3.9 kDalton single molecules at a signal-to-noise ration above unity.
We present the design of an optomechanical crystal nanobeam cavity that combines finite-element simulation with numerical optimization, and considers the optomechanical coupling arising from both moving dielectric boundaries and the photo-elastic effect. Applying this methodology results in a nanobeam with an experimentally realized intrinsic optical Q-factor of 1.2x10^6, a mechanical frequency of 5.1GHz, a mechanical Q-factor of 6.8x10^5 (at T=10K), and a zero-point-motion optomechanical coupling rate of g=1.1MHz.
The mechanical properties of light have found widespread use in the manipulation of gas-phase atoms and ions, helping create new states of matter and realize complex quantum interactions. The field of cavity-optomechanics strives to scale this interaction to much larger, even human-sized mechanical objects. Going beyond the canonical Fabry-Perot cavity with a movable mirror, here we explore a new paradigm in which multiple cavity-optomechanical elements are wired together to form optomechanical circuits. Using a pair of optomechanical cavities coupled together via a phonon waveguide we demonst…
Microelectromechanical systems (MEMS) have been applied to many measurement problems in physics, chemistry, biology and medicine. In parallel, cavity optomechanical systems have achieved quantum-limited displacement sensitivity and ground state cooling of nanoscale objects. By integrating a novel cavity optomechanical structure into an actuated MEMS sensing platform, we demonstrate a system with high quality-factor interferometric readout, electrical tuning of the optomechanical coupling by two orders of magnitude, and a mechanical transfer function adjustable via feedback. The platform separa…
We present a cavity piezo-optomechanical system where microwave and optical degrees of freedom are coupled through an ultra-high frequency mechanical resonator. By utilizing the coherence among the three interacting modes, we demonstrate optical amplification, coherent absorption and a more general asymmetric Fano resonance. The strong piezoelectric drive further allows access to the large-amplitude-induced optomechanical nonlinearity, with which optical transparency at higher harmonics through multi-phonon scattering is demonstrated.
Resonant photoelastic coupling in semiconductor nanostructures opens new perspectives for strongly enhanced light-sound interaction in optomechanical resonators. One potential problem, however, is the reduction of the cavity Q-factor induced by dissipation when the resonance is approached. We show in this letter that cavity-polariton mediation in the light-matter process overcomes this limitation allowing for a strongly enhanced photon-phonon coupling without significant lifetime reduction in the strongly-coupled regime. Huge optomechanical coupling factors in the PetaHz/nm range are envisaged…
A cavity optomechanical magnetometer is demonstrated where the magnetic field induced expansion of a magnetostrictive material is transduced onto the physical structure of a highly compliant optical microresonator. The resulting motion is read out optically with ultra-high sensitivity. Detecting the magnetostrictive deformation of Terfenol-D with a toroidal whispering gallery mode (TWGM) resonator a peak sensitivity of 400 nT/Hz^.5 was achieved with theoretical modelling predicting that sensitivities of up to 500 fT/Hz^.5 may be possible. This chip-based magnetometer combines high-sensitivity …
Using electromagnetically induced transparency we show how the opto-mechanical systems can be used both as memory elements as well as for the transduction of optical fields. We use a double cavity optomechanical system which facilitates such applications. By tuning the frequency of the second cavity one can produce output fields at a variety of frequencies. We present analytical results for the steady state behavior which is controlled by the power and the detuning of the field driving the second cavity.
Optical forces in guided-wave nanostructures have recently been proposed as an effective means of mechanically actuating and tuning optical components. In this work, we study the properties of a photonic crystal optomechanical cavity consisting of a pair of patterned silicon nitride nanobeams. Internal stresses in the stoichiometric silicon nitride thin-film are used to produce inter-beam slot-gaps ranging from 560 to 40nm. A general pump-probe measurement scheme is described which determines, self-consistently, the contributions of thermo-mechanical, thermo-optic, and radiation pressure effec…
Mechanical rotation and oscillation have far lower frequencies than light does; thus they are not coupled to each other conventionally. In this Letter, we show the torsional mechanical oscillation of an optical cavity can be coupled to the optical modes by introducing birefringence, which produces nondegenerate modes in the cavity: ordinary and extraordinary rays. Twisting the cavity mixes them and modulates the electromagnetic energy. We find torsional optomechanical Hamiltonian by quantising the total energy and reveal the torsional oscillation can be resonantly driven by light.
We present an experimental study of an optomechanical system formed by a vibrating thin semi-transparent membrane within a high-finesse optical cavity. We show that the coupling between the optical cavity modes and the vibrational modes of the membrane can be tuned by varying the membrane position and orientation. In particular we demonstrate a large quadratic dispersive optomechanical coupling in correspondence with avoided crossings between optical cavity modes weakly coupled by scattering at the membrane surface. The experimental results are well explained by a first order perturbation trea…
A tunable nanoscale "zipper" laser cavity, formed from two doubly clamped photonic crystal nanobeams, is demonstrated. Pulsed, room temperature, optically pumped lasing action at a wavelength of 1.3 micron is observed for cavities formed in a thin membrane containing InAsP/GaInAsP quantum-wells. Metal electrodes are deposited on the ends of the nanobeams to allow for micro-electro-mechanical actuation. Electrostatic tuning and modulation of the laser wavelength is demonstrated at a rate of 0.25nm/V^2 and a frequency as high as 6.7MHz, respectively.
We describe an optomechanical device consisting of a fiber-based optical cavity containing a silicon nitiride membrane. In comparison with typical free-space cavities, the fiber-cavity's small mode size (10 μm waist, 80 μm length) allows the use of smaller, lighter membranes and increases the cavity-membrane linear coupling to 3 GHz/nm and quadratic coupling to 20 GHz/nm^2. This device is also intrinsically fiber-coupled and uses glass ferrules for passive alignment. These improvements will greatly simplify the use of optomechanical systems, particularly in cryogenic settings. At room temperat…
We describe the design, fabrication, and characterization of a one-dimensional silicon photonic crystal cavity in which a central slot is used to enhance the overlap between highly localized optical and mechanical modes. The optical mode has an extremely small mode volume of 0.017 $(λ_{vac}/n)^3$, and an optomechanical vacuum coupling rate of 310 kHz is measured. With optical quality factors up to $1.2 \cdot 10^5$, fabricated devices are in the resolved-sideband regime. The electric field has its maximum at the slot wall and couples to the in-plane breathing motion of the slot. The optomechani…
We present a monolithic integrated aluminum nitride (AlN) optomechanical resonator in which the mechanical motion is actuated by piezoelectric force and the displacement is transduced by a high-Q optical cavity. The AlN optomechanical resonator is excited from a radio-frequency electrode via a small air gap to eliminate resonator-to-electrode loss. We observe the electrically excited mechanical motion at 47.3 MHz, 1.04 GHz, and 3.12 GHz, corresponding to the 1st, 2nd, and 4th radial-contour mode of the wheel resonator respectively. An equivalent circuit model is developed to describe the obser…
We review and study the roles of quantum and classical fluctuations in recent cavity-optomechanical experiments which have now reached the quantum regime (mechanical phonon occupancy < 1) using resolved sideband laser cooling. In particular, both the laser noise heating of the mechanical resonator and the form of the optically transduced mechanical spectra, modified by quantum and classical laser noise squashing, are derived under various measurement conditions. Using this theory, we analyze our recent ground-state laser cooling and motional sideband asymmetry experiments with nanoscale optome…
We study the role of stimulated Brillouin scattering in a fiber cavity by numerical simulations and a simple theoretical model and find good agreement between experiment, simulation and theory. We also investigate an optomechanical system based on a fiber cavity in the presence on the nonlinear Brillouin scattering. Using simulation and theory, we show that this hybrid optomechanical system increases optomechanical damping for low mechanical resonance frequencies in the unresolved sideband regime. Furthermore, optimal damping occurs for blue detuning in stark contrast to standard optomechanics…
We develop a chip-scale cavity optomechanical system in single-crystal lithium niobate that exhibits high optical quality factors and a large frequency-quality product as high as $3.6\times 10^{12}$ Hz at room temperature and atmosphere. The excellent optical and mechanical properties together with the strong optomechanical coupling allow us to efficiently excite the coherent regenerative optomechanical oscillation operating at 375.8 MHz with a threshold power of 174 ${\rm μW}$ in the air. The demonstrated lithium niobate optomechanical device enables great potential for achieving electro-opti…
Experiments involving micro- and nanomechanical resonators need to be carefully designed to reduce mechanical environmental noise. A small scale on-chip approach is to add an additional resonator to the system as a mechanical low-pass filter. Unfortunately, the inherent low frequency of the low-pass filter causes the system to be easily excited mechanically. Fixating the additional resonator ensures that the resonator itself can not be excited by the environment. This, however, negates the purpose of the low-pass filter. We solve this apparent paradox by applying active feedback to the resonat…
We investigate theoretically the effect of optical feedback from a cavity containing an ultracold two level atomic ensemble, on the bistable behavior shown by mean intracavity optical field and the ground state cooling effect of the mechanical oscillator in an optomechanical cavity resonator. The optical bistability can be controlled by tuning the frequency and power of the single driving laser as well as by varying the atom-cavity coupling strength in the atomic cavity. Study of the cooling of the mechanical oscillator, in both good and bad cavity limits, reveals that the hybrid system is mor…
We experimentally study an optomechanical cavity consisting of an oscillating mechanical resonator embedded in a superconducting microwave transmission line cavity. Tunable optomechanical coupling between the mechanical resonator and the microwave cavity is introduced by positioning a niobium-coated single mode optical fiber above the mechanical resonator. The capacitance between the mechanical resonator and the coated fiber gives rise to optomechanical coupling, which can be controlled by varying the fiber-resonator distance. We study radiation pressure induced self-excited oscillations as a …
Dynamical backaction has proven to be a versatile tool in cavity optomechanics, allowing for precise manipulation of a mechanical resonator's motion using confined optical photons. In this work, we present measurements of a silicon whispering-gallery-mode optomechanical cavity where backaction originates from opposing radiation pressure and photothermal forces, with the former dictating the optomechanical spring effect and the latter governing the optomechanical damping. At high enough optical input powers, we show that the photothermal force drives the mechanical resonator into self-oscillati…
We experimentally study a fiber-based optical ring cavity integrated with a mechanical resonator mirror and an optical amplifier. The device exhibits a variety of intriguing nonlinear effects including synchronization and self-excited oscillation. Passively generated optical pulses are observed when the frequency of the optical ring cavity is tuned very close to the mechanical frequency of the suspended mirror. The optical power at the threshold of this process of mechanical mode locking is found to be related to quantum noise of the optical amplifier.
We present the fabrication and characterization of an artificial crystal structure formed from a thin-film of silicon which has a full phononic bandgap for microwave X-band phonons and a two-dimensional pseudo-bandgap for near-infrared photons. An engineered defect in the crystal structure is used to localize optical and mechanical resonances in the bandgap of the planar crystal. Two-tone optical spectroscopy is used to characterize the cavity system, showing a large vacuum coupling rate of 220kHz between the fundamental optical cavity resonance at 195THz and a co-localized mechanical resonanc…
We demonstrate highly efficient coupling of light from an optical fiber to a silicon photonic crystal optomechanical cavity. The fiber-to-cavity coupling utilizes a compact (L ~ 25 um) intermediate adiabatic coupler. The optical coupling is lithographically controlled, broadband, relatively insensitive to fiber misalignment, and allows for light to be transferred from an optical fiber to, in principle, any photonic chip with refractive index greater than that of the optical fiber. Here we demonstrate single-sided cavity coupling with a total fiber-to-cavity optical power coupling efficiency of…
We experimentally study forced and self oscillations of an optomechanical cavity which is formed between a fiber Bragg grating that serves as a static mirror and between a freely suspended metallic mechanical resonator that serves as a moving mirror. In the domain of small amplitude mechanical oscillations, we find that the optomechanical coupling is manifested as changes in the effective resonance frequency, damping rate and cubic nonlinearity of the mechanical resonator. Moreover, self oscillations of the micromechanical mirror are observed above a certain optical power threshold. A comparis…
Microwave to optical transduction has received a great deal of interest from the cavity optomechanics community as a landmark application for electro-optomechanical systems. In this Letter, we demonstrate a novel transducer that combines high-frequency mechanical motion and a microwave cavity for the first time. The system consists of a 3D microwave cavity and a gallium arsenide optomechanical crystal, which has been placed in the microwave electric field maximum. This allows the microwave cavity to actuate the gigahertz-frequency mechanical breathing mode in the optomechanical crystal through…
Electronic resonances can significantly enhance the photon-phonon coupling in cavity optomechanics, but are normally avoided due to absorption losses and dephasing by inhomogeneous broadening. We experimentally demonstrate that exciton-polaritons in semiconductor microcavities enable GHz optomechanics with single-particle resonant couplings reaching record values in the 10s of MHz range. Moreover, this resonant enhancement is protected from inhomogeneous broadening by the Rabi gap. Single-polariton non-linearities and the optomechanical strong-coupling regime become accessible in this platform…
We study the optical cooling of the resonator mirror in a cavity-optomechanical system that contains an optical gain medium. We find that the optical damping rate is vanishingly small for an incoherently pumped laser above threshold. In the presence of an external coherent drive however, the optical damping rate can be enhanced substantially with respect to that of a passive cavity. We show that the strength of the incoherent pump provides a conduit to tune the damping rate and the minimum attainable phonon number with the same radiation pressure force, and the latter can be lowered from that …
Cavity optomechanics has become a powerful tool to manipulate mechanical motion via optical fields. When driving an optomechanical cavity with blue-detuned laser the mechanical motion is amplified, ultimately resulting in phonon lasing. In this work, we show that a silicon optomechanical crystal cavity can be used as an optoelectronic oscillator when driven to the phonon lasing condition. To this end, we use an optomechanical cavity designed to have a breathing-like mechanical mode vibrating at $Ω_{m}/2π=$3.897 GHz in a full phononic bandgap. Our measurements show that the first harmonic displ…
Recent nanofabrication technologies have miniaturized optical and mechanical resonators, and have led to a variety of novel optomechanical systems in which optical and mechanical modes are strongly coupled. Here we hybridize an optomechanical resonator with two-level emitters and successfully demonstrate all-optical dynamic control of optical transition in the two-level system by the mechanical oscillation via the cavity quantum-electrodynamics (CQED) effect. Employing copper-doped silicon nanobeam optomechanical resonators, we have observed that the spontaneous emission rate of excitons bound…
Integrated optomechanical cavities stand as a promising means to interface mechanical motion and guided optical modes. State-of-the-art demonstrations rely on optical and mechanical modes tightly confined of in micron-scale areas to achieve strong optomechanical coupling. However, the need for tight optomechanical confinement and the general use of suspended devices hinders interaction with external devices, limiting the potential for the implementation of complex circuits. Here, we propose and demonstrate a new approach for optomechanical cavities coupling free-propagating surface acoustic wa…
We theoretically study a strongly-driven optomechanical system which consists of a passive optical cavity and an active mechanical resonator. When the optomechanical coupling strength is varied, phase transitions, which are similar those observed in $\mathcal{PT}$-symmetric systems, are observed. We show that the optical transmission can be controlled by changing the gain of the mechanical resonator and loss of the optical cavity mode. Especially, we find that: (i) for balanced gain and loss, optical amplification and absorption can be tuned by changing the optomechanical coupling strength thr…
Micro- and nanomechanical resonators have emerged as promising platforms for sensing a broad range of physical properties such as mass, force, torque, magnetic field, and acceleration. The sensing performance relies critically on the motional mass, the mechanical frequency, and the linewidth of the mechanical resonator. Here, we demonstrate a hetero optomechanical crystal (OMC) cavity based on a silicon nanobeam structure. The cavity supports phonon lasing in a fundamental mechanical mode with a frequency of 5.91 GHz, an effective mass of 116 fg, and a mechanical linewidth narrowing from 3.3 M…
We study the cavity mode frequencies of a Fabry-Pérot cavity containing two vibrating dielectric membranes. We derive the equations for the mode resonances and provide approximate analytical solutions for them as a function of the membrane positions, which act as an excellent approximation when the relative and center-of-mass position of the two membranes are much smaller than the cavity length. With these analytical solutions, one finds that extremely large optomechanical coupling of the membrane relative motion can be achieved in the limit of highly reflective membranes when the two membrane…
Optomechanical systems offer new opportunities in quantum information processing and quantum sensing. Many solid-state quantum devices operate at millikelvin temperatures -- however, it has proven challenging to operate nanoscale optomechanical devices at these ultralow temperatures due to their limited thermal conductance and parasitic optical absorption. Here, we demonstrate a two-dimensional optomechanical crystal resonator capable of achieving large cooperativity $C$ and small effective bath occupancy $n_b$, resulting in a quantum cooperativity $C_{\text{eff}}\equiv C/n_b \approx 1.3 > 1$ …
We describe and demonstrate a method to control a detuned movable-mirror Fabry-Perot cavity using radiation pressure in the presence of a strong optical spring. At frequencies below the optical spring resonance, self-locking of the cavity is achieved intrinsically by the optomechanical (OM) interaction between the cavity field and the movable end mirror. The OM interaction results in a high rigidity and reduced susceptibility of the mirror to external forces. However, due to a finite delay time in the cavity, this enhanced rigidity is accompanied by an anti-damping force, which destabilizes th…
We study self-excited oscillations (SEO) in an on-fiber optomechanical cavity. Synchronization is observed when the optical power that is injected into the cavity is periodically modulated. A theoretical analysis based on the Fokker-Planck equation evaluates the expected phase space distribution (PSD) of the self-oscillating mechanical resonator. A tomography technique is employed for extracting PSD from the measured reflected optical power. Time-resolved state tomography measurements are performed to study phase diffusion and phase locking of the SEO. The detuning region inside which synchron…
Mechanical motion of photonic devices driven by optical forces provides a profound means of coupling between optical fields. The current focus of these optomechanical effects has been on cavity optomechanics systems in which co-localized optical and mechanical modes interact strongly to enable wave-mixing between photons and phonons and backaction cooling of mechanical modes. Alternatively, extended mechanical modes can also induce strong nonlocal effects on propagating optical fields or multiple localized optical modes at distances. Here, we demonstrate a novel multi-cavity optomechanical dev…
Photon statistics in a weakly driven optomechanical photonic crystal cavity, with Kerr-type nonlinearity, is analyzed both analytically and numerically. Single-photon blockade effect is demonstrated via calculations of the zero-time-delay second-order correlation function $g^{(2)}(0)$. The analytical results obtained by solving the Schrödinger equation are in complete conformity with the results obtained through numerical solution of the quantum master equation. The experimental feasibility with state-of-the-art device parameters is discussed. It is observed that photon blockade could be gener…
We study an optomechanical cavity, in which a buckled suspended beam serves as a mirror. The mechanical resonance frequency of the beam obtains a minimum value near the buckling temperature. Contrary to the common case, in which self-excited oscillations of the suspended mirror are optically induced by injecting blue detuned laser light, in our case self-excited oscillations are observed with red detuned light. These observations are attributed to a retarded thermal (i.e. bolometric) force acting on the buckled mirror in the inwards direction (i.e. towards to other mirror). With relatively hig…
Optomechanical coupling between a light field and the motion of a cavity mirror via radiation pressure plays an important role for the exploration of macroscopic quantum physics and for the detection of gravitational waves (GWs). It has been used to cool mechanical oscillators into their quantum ground states and has been considered to boost the sensitivity of GW detectors, e.g. via the optical spring effect. Here, we present the experimental characterization of generalized, that is, dispersive and dissipative optomechanical coupling, with a macroscopic (1.5mm)^2-sized silicon nitride (SiN) me…
We study a fully on-fiber optomechanical cavity and characterize its performance as a sensor. The cavity is formed by patterning a suspended metallic mirror near the tip of an optical fiber and by introducing a static reflector inside the fiber. Optically induced self-excited oscillation (SEO) is observed above a threshold value of the injected laser power. The SEO phase can be synchronized by periodically modulating the optical power that is injected into the cavity. Noise properties of the system in the region of synchronization are investigated. Moreover, the spectrum is measured near diffe…
Cavity optomechanical magnetic field sensors, constructed by coupling a magnetostrictive material to a micro-toroidal optical cavity, act as ultra-sensitive room temperature magnetometers with tens of micrometre size and broad bandwidth, combined with a simple operating scheme. Here, we develop a general recipe for predicting the field sensitivity of these devices. Several geometries are analysed, with a highest predicted sensitivity of 180~p$\textrm{T}/\sqrt{\textrm{Hz}}$ at 28~$μ$m resolution limited by thermal noise in good agreement with previous experimental observations. Furthermore, by …
