A novel dual-function radar communication (DFRC) system is proposed, that achieves high target resolution and high communication rate. It consists of a multiple-input multiple-output (MIMO) radar, where only a small number of antennas are active in each channel use. The probing waveforms are orthogonal frequency division multiplexing (OFDM) type. The OFDM carriers are divided into two groups, one that is used by the active antennas in a shared fashion, and another one, where each subcarrier is assigned to an active antenna in an exclusive fashion (private subcarriers). Target estimation is carried out based on the received and transmitted symbols. The system communicates information via the transmitted OFDM data symbols and the pattern of active antennas in a generalized spatial modulation (GSM) fashion. A multi-antenna communication receiver can identify the indices of active antennas via sparse signal recovery methods. The use of shared subcarriers enables high communication rate. The private subcarriers are used to synthesize a virtual array for high angular resolution, and also for improved estimation on the active antenna indices. The OFDM waveforms allow the communication receiver to easily mitigate the effect of frequency selective fading, while the use of a sparse array at the transmitter reduces the hardware cost of the system. The radar performance of the proposed DFRC system is evaluated via simulations, and bit error rate (BER) results for the communication system are provided.
An intelligent reflecting surface (IRS) consists of passive reflective elements capable of altering impinging waveforms. The IRS-aided radar systems have recently been shown to improve detection and estimation performance by exploiting the target information collected via non-line-of-sight paths. However, the waveform design problem for an IRS-aided radar has remained relatively unexplored. In this paper, we consider a multi-IRS-aided orthogonal frequency-division multiplexing (OFDM) radar and study the theoretically achievable accuracy of target detection. In addition, we jointly design the O…
Joint RADAR communication (JRC) systems that use orthogonal frequency division multiplexing (OFDM) can be compromised by an adversary that re-produces the received OFDM signal creating thus false RADAR targets. This paper presents a set of algorithms that can be deployed at the JRC system and can detect the presence of false targets. The presence of a false target is detected depending on whether there is residual carrier frequency offset (CFO) beyond Doppler in the received signal, with a Generalized Likelihood Ratio Test (GLRT). To evaluate the performance of our approach we measure the dete…
An integrated radar and communications system (IRCS) where a monostatic radar transceiver is employed for target classification while simultaneously used as a communications transmitter is considered. The radar combined propagation-target response (joint response of the radar propagation channel and target) and communications channel response are generally frequency selective but the corresponding frequency response functions are not exactly known. In particular, these frequency response functions are only known to lie in an uncertainty class. To ensure the IRCS simultaneously provides accepta…
In contrast to the state-of-the-art technology, it is envisaged that 5G systems will accommodate a broad range of services and a variety of emerging applications. In fact, the advent of the Internet of Things (IoT) and its integration with conventional human-initiated transmissions yields the need for a fundamental system redesign. Hence, the ideal waveform for the upcoming 5G radio access technology should cope with several requirements, such as low computational complexity, good time and frequency localization and straightforward extension to \emph{multiple-input multiple-output} (MIMO) syst…
We propose a novel three-stage delay-Doppler-angle estimation algorithm for a MIMO-OFDM radar in the presence of inter-carrier interference (ICI). First, leveraging the observation that spatial covariance matrix is independent of target delays and Dopplers, we perform angle estimation via the MUSIC algorithm. For each estimated angle, we next formulate the radar delay-Doppler estimation as a joint carrier frequency offset (CFO) and channel estimation problem via an APES (amplitude and phase estimation) spatial filtering approach by transforming the delay-Doppler parameterized radar channel int…
Recently, integrating the communication and sensing functions into a common network has attracted a great amount of attention. This paper considers the advanced signal processing techniques for enabling the radar to sense the environment via the communication signals. Since the technologies of orthogonal frequency division multiplexing (OFDM) and multiple-input multiple-output (MIMO) are widely used in the legacy cellular systems, this paper proposes a two-stage signal processing approach for radar sensing in an MIMO-OFDM system, where the scattered channels caused by various targets are estim…
This paper studies the processing principles, implementation challenges, and performance of OFDM-based radars, with particular focus on the fourth-generation Long-Term Evolution (LTE) and fifth-generation (5G) New Radio (NR) mobile networks' base stations and their utilization for radar/sensing purposes. First, we address the problem stemming from the unused subcarriers within the LTE and NR transmit signal passbands, and their impact on frequency-domain radar processing. Particularly, we formulate and adopt a computationally efficient interpolation approach to mitigate the effects of such emp…
In this paper, we explore a dual-functional radar-communication (DFRC) system for achieving integrated sensing and communications (ISAC). The technique of orthogonal frequency division multiplexing (OFDM) is leveraged to overcome the frequency-selective fading of the wideband multiple-input multiple-output (MIMO) systems with one multi-antenna DFRC base station (BS) and multiple single-antenna user equipment (UEs). In order to restrain the high peak-to-average power ratio (PAPR) of OFDM signals, we aim to jointly design low-PAPR DFRC MIMO-OFDM waveforms. This is done by utilizing a weighted ob…
This work analyzes the performance of the implementable detectors for multiple-input-multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM) technique under specific and realistic operation system condi- tions, including antenna correlation and array configuration. Time-domain channel model has been used to evaluate the system performance under realistic communication channel and system scenarios, including different channel correlation, modulation order and antenna arrays configurations. A bunch of MIMO-OFDM detectors were analyzed for the purpose of achieve high performance …
Hybrid beamforming is considered a key enabler to realize millimeter wave (mmWave) multiple-input multiple-output (MIMO) communications due to its capability of considerably reducing the number of costly and power-hungry radio frequency chains in the transceiver. However, in mmWave MIMO orthogonal frequency-division multiplexing (MIMO-OFDM) systems, hybrid beamforming design is challenging because the analog precoder and combiner are required to be shared across the whole employed bandwidth. In this paper, we propose closed-form solutions to the problem of designing the analog precoder/combine…
We propose in this work a radar detection system for orthogonal-frequency division multiplexing (OFDM) transmission. We assume that the transmitting antenna Tx is colocated with a monostatic radar. The latter knows the transmitted signal and listens to echoes coming from the reflection of fixed or moving targets. We estimate the targets parameters (range and velocity) using a 2D-Periodogram. Moreover, we improve the estimation performance in low signal to noise ratio (SNR) conditions using the discrete Fourier transform channel estimation (DFT-CE) and we show that Zadoff-Chu precoding (ZCP) ad…
This paper considers the problem of estimating the sparse mmWave massive multiple input - multiple output (MIMO) OFDM channel from one-bit quantized measurements. Unlike previous grid-based one-bit compressive sensing approaches, we present a gridless convex method to recover sparse channel form one-bit measurements via Binary Atomic Norm Minimization (BiANM) and Reweighted Binary Atomic Norm Minimization (ReBiANM). Simulation results verify the accuracy of the binary and reweighted binary atomic norm minimization techniques.
Accurate channel estimation is critical to the performance of orthogonal frequency-division multiplexing (OFDM) underwater acoustic (UWA) communications, especially under multiple-input multiple-output (MIMO) scenarios. In this paper, we explore Vector Approximate Message Passing (VAMP) coupled with Expected Maximum (EM) to obtain channel estimation (CE) for MIMO OFDM UWA communications. The EM-VAMP-CE scheme is developed by employing a Bernoulli-Gaussian (BG) prior distribution for the channel impulse response, and hyperparameters of the BG prior distribution are learned via the EM algorithm.…
In this paper, we analyze the performance of evolutionary heuristic-aided linear detectors deployed in Multiple-Input Multiple-Output (MIMO) Orthogonal Frequency-Division Multiplexing (OFDM) systems, considering realistic operating scenarios. Hybrid linear-heuristic detectors under different initial solutions provided by linear detectors are considered, namely differential evolution (DE) and particle swarm optimization (PSO). Numerical results demonstrated the applicability of hybrid detection approach, which can improve considerably the performance of minimum mean-square error (MMSE) and matc…
Herein, an atomic norm based method for accurately estimating the location and orientation of a target from millimeter-wave multi-input-multi-output (MIMO) orthogonal frequency-division multiplexing (OFDM) signals is presented. A novel virtual channel matrix is introduced and an algorithm to extract localization-relevant channel parameters from its atomic norm decomposition is designed. Then, based on the extended invariance principle, a weighted least squares problem is proposed to accurately recover the location and orientation using both line-of-sight and non-line-of-sight channel informati…
Distributed MIMO radar is known to achieve superior sensing performance by employing widely separated antennas. However, it is challenging to implement a low-complexity distributed MIMO radar due to the complex operations at both the receivers and the fusion center. This work proposed a low-bit quantized distributed MIMO (LiQuiD-MIMO) radar to significantly reduce the burden of signal acquisition and data transmission. In the LiQuiD-MIMO radar, the widely-separated receivers are restricted to operating with low-resolution ADCs and deliver the low-bit quantized data to the fusion center. At the…
The slice-wise multiplication of two tensors is required in a variety of tensor decompositions (including PARAFAC2 and PARATUCK2) and is encountered in many applications, including the analysis of multidimensional biomedical data (EEG, MEG, etc.) or multi-carrier MIMO systems. In this paper, we propose a new tensor representation that is not based on a slice-wise (matrix) description, but can be represented by a double contraction of two tensors. Such a double contraction of two tensors can be efficiently calculated via generalized unfoldings. It leads to new tensor models of the investigated …
A novel monostatic multiple-input multiple-output (MIMO) dual-function radar communication (DFRC) system is proposed, that uses the available bandwidth efficiently for both sensing and communication. The proposed system, referred to as Shared-Subcarriers DFRC (SS-DFRC) transmits wideband, orthogonal frequency division multiplexing (OFDM) waveforms and allows the transmit antennas to use subcarriers in a shared fashion. A novel, low complexity target estimation approach is proposed to overcome the coupling of radar target parameters and transmitted symbols that arises in that case. When all sub…
Future wireless communication systems are expected to explore spectral bands typically used by radar systems, in order to overcome spectrum congestion of traditional communication bands. Since in many applications radar and communication share the same platform, spectrum sharing can be facilitated by joint design as dual function radar-communications system. In this paper, we propose a joint transmit beamforming model for a dual-function multiple-input-multiple-output (MIMO) radar and multiuser MIMO communication transmitter sharing the spectrum and an antenna array. The proposed dual-function…
Millimeter-wave radars are being increasingly integrated into commercial vehicles to support advanced driver-assistance system features. A key shortcoming for present-day vehicular radar imaging is poor azimuth resolution (for side-looking operation) due to the form factor limits on antenna size and placement. In this paper, we propose a solution via a new multiple-input and multiple-output synthetic aperture radar (MIMO-SAR) imaging technique, that applies coherent SAR principles to vehicular MIMO radar to improve the side-view (angular) resolution. The proposed 2-stage hierarchical MIMO-SAR …
Multi-input multi-output orthogonal frequency division multiplexing (MIMO OFDM) is a key technology for mobile communication systems. However, due to the issue of high peak-to-average power ratio (PAPR), the OFDM symbols may suffer from nonlinear distortions of the power amplifier (PA) at the transmitters, which degrades the channel estimation and detection performances of the receivers. To mitigate the clipping distortions at the receivers end, we leverage deep learning (DL) and devise a DL based receiver which is aided by the traditional least square (LS) channel estimation and the zero-forc…
Joint Synchronization and Radar Parameter Estimation for OFDM-based DISAC Systems
School of Computer Science and Engineering, Constructor University（康斯坦茨大学计算机科学与工程学院）；Department of Electrical and Computer Engineering, University of California San Diego（加州大学圣地亚哥分校电气与计算机工程学院）
Digital predistortion (DPD) is a method commonly used to compensate for the nonlinear effects of power amplifiers (PAs). However, the computational complexity of most DPD algorithms becomes an issue in the downlink of massive multi-user (MU) multiple-input multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM), where potentially up to several hundreds of PAs in the base station (BS) require linearization. In this paper, we propose a convolutional neural network (CNN)-based DPD in the frequency domain, taking place before the precoding, where the dimensionality of the signal s…
This paper proposes the use of sufficient cyclic prefix (CP) OFDM synthetic aperture radar (SAR) for foliage penetration (FOPEN). The foliage introduces phase and amplitude fluctuation which cause the sidelobes to increase and affects the final image of the obscured targets. The wideband CP-based OFDM SAR inherently eliminates the sidelobes that arise from the interference between targets on the same range line. The integrated sidelobe level ratio (ISLR) of the CP-based OFDM signal along the range direction is lower than that of the random noise signal by 2 dB for foliage penetration applicati…
Dual-function radar-communication (DFRC) based on frequency hopping (FH) MIMO radar (FH-MIMO DFRC) achieves symbol rate much higher than radar pulse repetition frequency. Such DFRC, however, is prone to eavesdropping due to the spatially uniform illumination of FH-MIMO radar. How to enhance the physical layer security of FH-MIMO DFRC is vital yet unsolved. In this paper, we reveal the potential of using permutations of hopping frequencies to achieve secure and high-speed FH-MIMO DFRC. Detecting permutations at a communication user is challenging due to the dependence on spatial angle. We propo…
Massive MIMO requires a large number of antennas and the same amount of power amplifiers (PAs), one per antenna. As opposed to 4G base stations, which could afford highly linear PAs, next-generation base stations will need to use inexpensive PAs, which have a limited region of linear amplification. One of the research challenges is effectively handling signals which have high peak-to-average power ratios (PAPRs), such as orthogonal frequency division multiplexing (OFDM). This paper introduces a PAPR-aware precoding scheme that exploits the excessive spatial degrees-of-freedom of large scale mu…
The impact of spatial correlation on mutual information (MI) is analyzed for MIMO radar. Unlike the work done in literature for statistical MIMO radar, we consider the spatial correlation of the target matrix elements to study the correlated MIMO radar performance. There is a trade-off between coherent processing gain in correlated MIMO radar and spatial diversity gain of target scatterers in uncorrelated MIMO radar. We address how the MI between the received signal and target channel matrix is affected by spatial correlation. Using majorization theory and the notion of Schur-convexity, we pro…
Multiple-input multiple-output (MIMO) radar has several advantages with respect to the traditional radar array systems in terms of performance and flexibility. However, in order to achieve high angular resolution, a MIMO radar requires a large number of transmit and receive antennas, which increases hardware design and computational complexities. Although spatial compressive sensing (CS) has been recently considered for a pulsed-waveform MIMO radar with sparse random arrays, such methods for the frequency-modulated continuous wave (FMCW) radar remain largely unexplored. In this context, we pro…
Adopting one-bit analog-to-digital convertors (ADCs) for massive multiple-input multiple-output (MIMO) implementations has great potential in reducing the hardware cost and power consumption. However, distortions caused by quantization raise great challenges. In MIMO orthogonal frequency-division modulation (OFDM) detection, coarse quantization renders the orthogonal separation among subcarriers inapplicable, forcing us to deal with a problem that has a very large problem size. In this paper we study the expectation-maximization (EM) approach for one-bit MIMO-OFDM detection. The idea is to ite…
Virginia Tech（弗吉尼亚理工大学）；Samsung Research America（三星美国研究院）
In this paper, we investigate learning-based MIMO-OFDM symbol detection strategies focusing on a special recurrent neural network (RNN) -- reservoir computing (RC). We first introduce the Time-Frequency RC to take advantage of the structural information inherent in OFDM signals. Using the time domain RC and the time-frequency RC as the building blocks, we provide two extensions of the shallow RC to RCNet: 1) Stacking multiple time domain RCs; 2) Stacking multiple time-frequency RCs into a deep structure. The combination of RNN dynamics, the time-frequency structure of MIMO-OFDM signals, and th…
