Future wireless communication systems are expected to explore spectral bands typically used by radar systems, in order to overcome spectrum congestion of traditional communication bands. Since in many applications radar and communication share the same platform, spectrum sharing can be facilitated by joint design as dual function radar-communications system. In this paper, we propose a joint transmit beamforming model for a dual-function multiple-input-multiple-output (MIMO) radar and multiuser MIMO communication transmitter sharing the spectrum and an antenna array. The proposed dual-function system transmits the weighted sum of independent radar waveform and communication symbols, forming multiple beams towards the radar targets and the communication receivers, respectively. The design of the weighting coefficients is formulated as an optimization problem whose objective is the performance of the MIMO radar transmit beamforming, while guaranteeing that the signal-to-interference-plus-noise ratio (SINR) at each communication user is higher than a given threshold. Despite the non-convexity of the proposed optimization problem, it can be relaxed into a convex one, which can be solved in polynomial time, and we prove that the relaxation is tight. Then, we propose a reduced complexity design based on zero-forcing the inter-user interference and radar interference. Unlike previous works, which focused on the transmission of communication symbols to synthesize a radar transmit beam pattern, our method provides more degrees of freedom for MIMO radar and is thus able to obtain improved radar performance, as demonstrated in our simulation study. Furthermore, the proposed dual-function scheme approaches the radar performance of the radar-only scheme, i.e., without spectrum sharing, under reasonable communication quality constraints.
In this letter, we investigate the millimeter wave (mmWave) downlink multiuser multiple-input multiple-output (MU-MIMO) system, adopting the dynamic subarray architecture at the base station and considering the multi-stream communication for each user. Aiming at maximizing the system spectral efficiency, we propose a novel hybrid beamforming design. First, assuming no inter-user interference (IUI), we easily get the optimal fully-digital beamformers and combiners using the singular value decomposition of each user channel and the waterfilling algorithm. Then, based on the obtained fullydigital…
The paper presents a joint beamforming algorithm using statistical channel state information (S-CSI) for reconfigurable intelligent surfaces (RIS) for multiuser MISO wireless communications. We used S-CSI, which is a long-term average of the cascaded channel as opposed to instantaneous CSI utilized in most existing works. Through this method, the overhead of channel estimation is dramatically reduced. We propose a proximal policy optimization (PPO) algorithm which is a well-known actor-critic based reinforcement learning (RL) algorithm to solve the optimization problem. To test the efficacy of…
This paper investigates the problem of resource allocation for multiuser communication networks with a reconfigurable intelligent surface (RIS)-assisted wireless transmitter. In this network, the sum transmit power of the network is minimized by controlling the phase beamforming of the RIS and transmit power of the BS. This problem is posed as a joint optimization problem of transmit power and RIS control, whose goal is to minimize the sum transmit power under signal-to-interference-plus-noise ratio (SINR) constraints of the users. To solve this problem, a dual method is proposed, where the du…
In this letter, we consider optimal hybrid beamforming design to minimize the transmission power under individual signal-to-interference-plus-noise ratio (SINR) constraints in a multiuser massive multiple-input-multiple-output (MIMO) system. This results in a challenging non-convex optimization problem. We consider two cases. In the case where the number of users is smaller than or equal to that of radio frequency (RF) chains, we propose a low-complexity method to obtain a globally optimal solution and show that it achieves the same transmission power as an optimal fully-digital beamformer. In…
Energy beamforming has emerged as a promising technique for enhancing the energy transfer efficiency of wireless power transfer (WPT). However, the performance of conventional energy beamforming may seriously degrade due to the non-linear radio frequency (RF) to direct current (DC) conversion at energy receivers (ERs). To tackle this issue, this letter proposes a new time-division energy beamforming, in which different energy beamforming matrices (of high ranks in general) are time shared to exploit the "convex-concave" shape of the RF-DC power relation at ERs. By considering a particular time…
Implicit Neural Representation for Multiuser Continuous Aperture Array Beamforming
School of Electronics and Information Engineering, Beihang University（北京航空航天大学电子信息工程学院）；School of Electronic Engineering and Computer Science, Queen Mary University of London（伦敦大学玛丽女王学院电子工程与计算机科学学院）
Configuring millimeter wave links following a conventional beam training protocol, as the one proposed in the current cellular standard, introduces a large communication overhead, specially relevant in vehicular systems, where the channels are highly dynamic. In this paper, we propose the use of a passive radar array to sense automotive radar transmissions coming from multiple vehicles on the road, and a radar processing chain that provides information about a reduced set of candidate beams for the links between the road-infrastructure and each one of the vehicles. This prior information can b…
In this paper, we propose a beamforming design for dual-functional radar-communication (DFRC) systems at the millimeter wave (mmWave) band, where hybrid beamforming and sub-arrayed MIMO radar techniques are jointly exploited. We assume that a base station (BS) is serving a user equipment (UE) located in a Non-Line-of-Sight (NLoS) channel, which in the meantime actively detects multiple targets located in a Line-of-Sight (LoS) channel. Given the optimal communication beamformer and the desired radar beampattern, we propose to design the analog and digital beamformers under non-convex constant-m…
Joint radar-communications (JRC) benefits from multi-functionality of radar and communication operations using same hardware and radio frequency (RF) spectrum resources. Thus JRC systems possess very high potential to be employed into the sixth generation (6G) standards. This paper designs a flexible beamformer for multiple-input multiple output (MIMO) JRC with maximized spectral efficiency (SE). Hybrid beamforming is implemented which constitutes lesser number of RF chains than number of transmitter antennas. We jointly express JRC rate with communication and radar entities including a weight…
In this paper, we propose a radar-assisted predictive beamforming design for vehicle-to-infrastructure (V2I) communication by relying on the joint sensing and communication functionalities at road side units (RSUs). We present a novel extended Kalman filtering (EKF) framework to track and predict kinematic parameters of the vehicle. By exploiting the radar functionality of the RSU we show that the communication beam tracking overheads can be drastically reduced. Numerical results have demonstrated that the proposed radar-assisted approach significantly outperforms the communication-only feedba…
Cognitive multiple-input multiple-output (MIMO) radar is capable of adjusting system parameters adaptively by sensing and learning in complex dynamic environment. Beamforming performance of MIMO radar is guided by both beamforming weight coefficients and the transceiver configuration. We propose a cognitive-driven MIMO array design where both the beamforming weights and the transceiver configuration are adaptively and concurrently optimized under different environmental conditions. The perception-action cycle involves data collection of full virtual array, covariance reconstruction and joint d…
In this paper, we propose an energy-efficient radar beampattern design framework for a Millimeter Wave (mmWave) massive multi-input multi-output (mMIMO) system, equipped with a hybrid analog-digital (HAD) beamforming structure. Aiming to reduce the power consumption and hardware cost of the mMIMO system, we employ a machine learning approach to synthesize the probing beampattern based on a small number of RF chains and antennas. By leveraging a combination of softmax neural networks, the proposed solution is able to achieve a desirable beampattern with high accuracy.
This work presents a novel robust beamforming design dedicated for dual-functional radar and communication (DFRC) base stations (BSs) in the context of integrated sensing and communications (ISAC). The architecture is intended for circumstances with imperfect channel state information (CSI). Our suggested approach demonstrates several tradeoffs for joint radar-communication deployment. Due to the DFRC nature of the design, the beamformer can simultaneously point towards an intended target, while optimizing communication quality of service. We unveil several insights regarding closed form expre…
This article studies and derives beamforming design in a dual-functional radar-communication (DFRC) multiple-input-multiple-output system. We focus on a scenario, where the DFRC base station communicates with downlink communication users, with imperfect channel state information knowledge, and performs target detection, all via the same transmit signal. Through careful relaxation procedures, we arrive at a suitable and novel optimization problem, which maximizes the radar output power in the Bartlett sense, under probabilistic outage signal-to-interference-and-noise ratio constraints. Theoreti…
In this paper, we develop a predictive beamforming scheme based on the dual-functional radar-communication (DFRC) technique, where the road-side units estimates the motion parameters of vehicles exploiting the echoes of the DFRC signals. Compared to the conventional feedback-based beam tracking approaches, the proposed method can reduce the signaling overhead and improve the tracking performance. A novel message passing algorithm is proposed, which yields a near optimal performance achieved by the maximum a posteriori estimation. Simulation results have shown the effectiveness of the proposed …
Sparse array design aided by emerging fast sensor switching technologies can lower the overall system overhead by reducing the number of expensive transceiver chains. In this paper, we examine the active sparse array design enabling the maximum signal to interference plus noise ratio (MaxSINR) beamforming at the MIMO radar receiver. The proposed approach entails an entwined design, i.e., jointly selecting the optimum transmit and receive sensor locations for accomplishing MaxSINR receive beamforming. Specifically, we consider a co-located multiple-input multiple-output (MIMO) radar platform wi…
As a cost-effective alternative, hybrid analog and digital beamforming architecture is a promising scheme for millimeter wave (mmWave) system. This paper considers two hybrid beamforming architectures, i.e. the partially-connected and fully-connected structures, for mmWave dual-function radar communication (DFRC) system, where the transmitter communicates with the downlink users and detects radar targets simultaneously. The optimization problems are formulated by minimizing a weighted summation of radar and communication performance, subject to constant modulus and power constraints. To tackle…
Intelligent reflecting surface (IRS) is a promising technology being considered for future wireless communications due to its ability to control signal propagation. This paper considers the joint active and passive beamforming problem for an IRS-assisted radar, where multiple IRSs are deployed to assist the surveillance of multiple targets in cluttered environments. Specifically, we aim to maximize the minimum target illumination power at multiple target locations by jointly optimizing the active beamformer at the radar transmitter and the passive phase-shift matrices at the IRSs, subject to a…
The dual-functional radar and communication (DFRC) technique constitutes a promising next-generation wireless solution, due to its benefits in terms of power consumption, physical hardware, and spectrum exploitation. In this paper, we propose sophisticated beamforming designs for multi-user DFRC systems by additionally taking the physical layer security (PLS) into account. We show that appropriately designed radar waveforms can also act as the traditional artificial noise conceived for drowning out the eavesdropping channel and for attaining increased design degrees of freedom (DoF). The joint…
Reconfigurable intelligent surface has recently emerged as a promising technology for shaping the wireless environment by leveraging massive low-cost reconfigurable elements. Prior works mainly focus on a single-layer metasurface that lacks the capability of suppressing multiuser interference. By contrast, we propose a stacked intelligent metasurface (SIM)-enabled transceiver design for multiuser multiple-input single-output downlink communications. Specifically, the SIM is endowed with a multilayer structure and is deployed at the base station to perform transmit beamforming directly in the e…
In vehicular networks of the future, sensing and communication functionalities will be intertwined. In this paper, we investigate a radar-assisted predictive beamforming design for vehicle-to-infrastructure (V2I) communication by exploiting the dual-functional radar-communication (DFRC) technique. Aiming for realizing joint sensing and communication functionalities at road side units (RSUs), we present a novel extended Kalman filtering (EKF) framework to track and predict kinematic parameters of each vehicle. By exploiting the radar functionality of the RSU we show that the communication beam …
This paper investigates the passive beamforming and information transfer (PBIT) technique for the multiuser multiple-input multiple-output (MIMO) systems with the aid of a reconfigurable intelligent surface (RIS), where the RIS enhances the primary communication via passive beamforming and at the same time delivers additional information by the spatial modulation (which adjusts the on-off states of the reflecting elements). For the passive beamforming design, we propose to maximize the sum channel capacity of the RIS-aided multiuser MIMO channel and formulate the problem as a two-step stochast…
This paper considers transmit beamforming in dual-function radar-communication (DFRC) system, where a DFRC transmitter simultaneously communicates with a communication user and detects a malicious target with the same waveform. Since the waveform is embedded with information, the information is risked to be intercepted by the target. To address this problem, physical-layer security technique is exploited. By using secrecy rate and estimation rate as performance measure for communication and radar, respectively, three secrecy rate maximization (SRM) problems are formulated, including the SRM wi…
In this paper, we consider the design of a multiple-input multiple-output (MIMO) transmitter which simultaneously functions as a MIMO radar and a base station for downlink multiuser communications. In addition to a power constraint, we require the covariance of the transmit waveform be equal to a given optimal covariance for MIMO radar, to guarantee the radar performance. With this constraint, we formulate and solve the signal-to-interference-plus-noise ratio (SINR) balancing problem for multiuser transmit beamforming via convex optimization. Considering that the interference cannot be complet…
Integrated sensing and communication (ISAC), which allows individual radar and communication systems to share the same spectrum bands, is an emerging and promising technique for alleviating spectrum congestion problems. In this paper, we investigate how to exploit the inherent interference from strong radar signals to ensure the physical layer security (PLS) for the considered multi-user multi-input single-output (MU-MISO) communication and colocated multi-input multi-output (MIMO) radar coexistence system. In particular, with known eavesdroppers' channel state information (CSI), we propose to…
In multiuser communication systems, user scheduling and beamforming (US-BF) design are two fundamental problems that are usually studied separately in the existing literature. In this work, we focus on the joint US-BF design with the goal of maximizing the set cardinality of scheduled users, which is computationally challenging due to the non-convex objective function and the coupled constraints with discrete-continuous variables. To tackle these difficulties, a successive convex approximation based US-BF (SCA-USBF) optimization algorithm is firstly proposed. Then, inspired by wireless intelli…
This paper studies an intelligent reflecting surface (IRS)-assisted multiuser multiple-input single-output (MISO) simultaneous wireless information and power transfer (SWIPT) system. In this system, a multi-antenna access point (AP) uses transmit beamforming to send both information and energy signals to a set of receivers each for information decoding (ID) or energy harvesting (EH), and a dedicatedly deployed IRS properly controls its reflecting phase shifts to form passive reflection beams for facilitating both ID and EH at receivers. Under this setup, we jointly optimize the (active) inform…
The dual-functional radar-communication (DFRC) system is an attractive technique, since it can support both wireless communications and radar by a unified hardware platform with real-time cooperation. Considering the appealing feature of multiple beams, this paper proposes a precoding scheme that simultaneously support multiuser transmission and target detection, with an integrated continuous phase modulation (CPM) and linear frequency modulation (LFM) signal, based on the designed dual mode framework. Similarly to the conception of communication rate, this paper defines radar rate to unify th…
In this paper, we consider hybrid beamforming designs for multiuser massive multiple-input multiple-output (MIMO)-orthogonal frequency division multiplexing (OFDM) systems. Aiming at maximizing the weighted spectral efficiency, we propose one alternating maximization framework where the analog precoding is optimized by Riemannian manifold optimization. If the digital precoding is optimized by a locally optimal algorithm, we obtain a locally optimal alternating maximization algorithm. In contrast, if we use a weighted minimum mean square error (MMSE)-based iterative algorithm for digital precod…
