Millimeter-wave (mmWave) communications have been one of the promising technologies for future wireless networks that integrate a wide range of data-demanding applications. To compensate for the large channel attenuation in mmWave band and avoid high hardware cost, a lens-based beamspace massive multiple-input multiple-output (MIMO) system is considered. However, the beam squint effect in wideband mmWave systems makes channel estimation very challenging, especially when the receiver is equipped with a limited number of radio-frequency (RF) chains. Furthermore, the real channel data cannot be obtained before the mmWave system is used in a new environment, which makes it impossible to train a deep learning (DL)-based channel estimator using real data set beforehand. To solve the problem, we propose a model-driven unsupervised learning network, named learned denoising-based generalized expectation consistent (LDGEC) signal recovery network. By utilizing the Stein's unbiased risk estimator loss, the LDGEC network can be trained only with limited measurements corresponding to the pilot symbols, instead of the real channel data. Even if designed for unsupervised learning, the LDGEC network can be supervisingly trained with the real channel via the denoiser-by-denoiser way. The numerical results demonstrate that the LDGEC-based channel estimator significantly outperforms state-of-the-art compressive sensing-based algorithms when the receiver is equipped with a small number of RF chains and low-resolution ADCs.
Millimeter-wave (mmWave) multiple-input multiple-out (MIMO) systems relying on lens antenna arrays are capable of achieving a high antenna-gain at a considerably reduced number of radio frequency (RF) chains via beam selection. However, the traditional beam selection network suffers from significant performance loss in wideband systems due to the effect of beam squint. In this paper, we propose a phase shifter-aided beam selection network, which enables a single RF chain to support multiple focused-energy beams, for mitigating the beam squint in wideband mmWave MIMO systems. Based on this arch…
In this paper, a framework of beamspace channel estimation in millimeter wave (mmWave) massive MIMO system is proposed. The framework includes the design of hybrid precoding and combining matrix as well as the search method for the largest entry of over-sampled beamspace receiving matrix. Then based on the framework, three channel estimation schemes including identity matrix approximation (IA)-based scheme, scattered zero off-diagonal (SZO)-based scheme and concentrated zero off-diagonal (CZO)-based scheme are proposed. These schemes together with the existing channel estimation schemes are co…
Millimeter-wave massive multiple-input multiple-output (MIMO) can use a lens antenna array to considerably reduce the number of radio frequency (RF) chains, but channel estimation is challenging due to the number of RF chains is much smaller than that of antennas. By exploiting the sparsity of beamspace channels, the beamspace channel estimation can be formulated as a sparse signal recovery problem, which can be solved by the classical iterative algorithm named approximate message passing (AMP), and its corresponding version learned AMP (LAMP) realized by a deep neural network (DNN). However, …
Of the wide palette of 5G features, ultra-wide bandwidth and large-scale antenna configuration are regarded as the essential enabling technology components at millimeter wave (mmWave) communication. Accurate knowledge of delay and angle information of multipath components is essential for many applications in mmWave systems. There is a strong need for a low computation-cost channel estimation algorithm for such systems, where typically adopted far-field and narrowband assumptions might be violated. In this work, a generic yet novel beamspace uniform circular array (UCA) beamforming algorithm w…
Massive multi-user multiple-input multiple-output (MU-MIMO) wireless systems operating at millimeter-wave (mmWave) frequencies enable simultaneous wideband data transmission to a large number of users. In order to reduce the complexity of MU precoding in all-digital basestation architectures, we propose a two-stage precoding architecture that first performs precoding using a sparse matrix in the beamspace domain, followed by an inverse fast Fourier transform that converts the result to the antenna domain. The sparse precoding matrix requires a small number of multipliers and enables regular ha…
We propose equalization-based data detection algorithms for all-digital millimeter-wave (mmWave) massive multiuser multiple-input multiple-out (MU-MIMO) systems that exploit sparsity in the beamspace domain to reduce complexity. We provide a condition on the number of users, basestation antennas, and channel sparsity for which beamspace equalization can be less complex than conventional antenna-domain processing. We evaluate the performance-complexity trade-offs of existing and new beamspace equalization algorithms using simulations with realistic mmWave channel models. Our results reveal that…
We propose sparsity-adaptive beamspace channel estimation algorithms that improve accuracy for 1-bit data converters in all-digital millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) basestations. Our algorithms include a tuning stage based on Stein's unbiased risk estimate (SURE) that automatically selects optimal denoising parameters depending on the instantaneous channel conditions. Simulation results with line-of-sight (LoS) and non-LoS mmWave massive MIMO channel models show that our algorithms improve channel estimation accuracy with 1-bit measurements in a computatio…
The rate loss is an important issue for multi-user beamspace multiple-input multiple-output (MIMO) millimeter-wave systems. In such systems, multi-cluster channel propagation leads as a function of the quantization error and, as a result, each active user suffers a significant rate loss. Particularly, a conventional single beam selection (SBS) scheme is used in an equivalent beamspace MIMO channel to reduce the required number of radio frequency (RF) chains, but this scheme does not properly mitigate the quantization error due to the limited number of the channel propagation clusters per-user.…
In this paper, we propose an accurate two-phase millimeter-Wave (mmWave) beamspace channel tracking mechanism. Particularly in the first phase, we train an extreme reservoir machine (ERM) for tracking the historical features of the mmWave beamspace channel and predicting them in upcoming time steps. Towards a more accurate prediction, we further fine-tune the ERM by means of Xavier initializer technique, whereby the input weights in ERM are initially derived from a zero mean and finite variance Gaussian distribution, leading to 49% degradation in prediction variance of the conventional ERM. Th…
Beamspace processing is an emerging technique to reduce baseband complexity in massive multiuser (MU) multiple-input multiple-output (MIMO) communication systems operating at millimeter-wave (mmWave) and terahertz frequencies. The high directionality of wave propagation at such high frequencies ensures that only a small number of transmission paths exist between user equipments and basestation (BS). In order to resolve the sparse nature of wave propagation, beamspace processing traditionally computes a spatial discrete Fourier transform (DFT) across a uniform linear antenna array at the BS whe…
Massive multi-antenna millimeter wave (mmWave) and terahertz wireless systems promise high-bandwidth communication to multiple user equipments in the same time-frequency resource. The high path loss of wave propagation at such frequencies and the fine-grained nature of beamforming with massive antenna arrays necessitates accurate channel estimation to fully exploit the advantages of such systems. In this paper, we propose BEAmspace CHannel EStimation (BEACHES), a low-complexity channel estimation algorithm for multi-antenna mmWave systems and beyond. BEACHES leverages the fact that wave propag…
Millimeter-wave (mmWave) communication in combination with massive multiuser multiple-input multiple-output (MU-MIMO) enables high-bandwidth data transmission to multiple users in the same time-frequency resource. The strong path loss of wave propagation at such high frequencies necessitates accurate channel state information to ensure reliable data transmission. We propose a novel channel estimation algorithm called BEAmspace CHannel EStimation (BEACHES), which leverages the fact that wave propagation at mmWave frequencies is predominantly directional. BEACHES adaptively denoises the channel …
Millimeter-wave (mmW)/Terahertz (THz) wideband communication employing a large-scale antenna array is a promising technique of the sixth-generation (6G) wireless network for realizing massive machine-type communications (mMTC). To reduce the access latency and the signaling overhead, we design a grant-free random access scheme based on joint active device detection and channel estimation (JADCE) for mmW/THz wideband massive access. In particular, by exploiting the simultaneously sparse and low-rank structure of mmW/THz channels with spreads in the delay-angular domain, we propose two multi-ran…
Millimeter-wave (mmWave) systems use directional beams to support high-rate data communications. Small misalignment between the transmit and receive beams (e.g., due to the mobility) can result in significant drop of the received signal quality especially in line-of-sight communication channels. In this paper, we propose and evaluate high-resolution angle tracking strategies for wideband mmWave systems with mobility. We custom design pairs of auxiliary beams as the tracking beams, and use them to capture the angle variations, towards which the steering directions of the data beams are adjusted…
In this work, the uplink channel estimation problem is considered for a millimeter wave (mmWave) multi-input multi-output (MIMO) system. It is well known that pilot overhead and computation complexity in estimating the channel increases with the number of antennas and the bandwidth. To overcome this, the proposed approach allows the channel estimation at the base station to be aided by the sensing information. The sensing information contains an estimate of scatterers locations in an environment. A simultaneous weighting orthogonal matching pursuit (SWOMP) - sparse Bayesian learning (SBL) algo…
Beamspace millimeter-wave (mmWave) and terahertz (THz) massive MIMO constitute attractive schemes for next-generation communications, given their abundant bandwidth and high throughput. However, their user and beam selection problem has to be efficiently addressed. Inspired by this challenge, we develop low-complexity solutions explicitly. We introduce the dirty paper coding (DPC) into the joint user and beam selection problem. We unveil the compelling properties of the DPC sum rate in beamspace massive MIMO, showing its monotonic evolution against the number of users and beams selected. We th…
We present a beamforming algorithm for multiuser wideband millimeter wave (mmWave) communication systems where one access point uses hybrid analog/digital beamforming while multiple user stations have phased-arrays with a single RF chain. The algorithm operates in a more general mode than others available in literature and has lower computational complexity and training overhead. Throughout the paper, we describe: i) the construction of novel beamformer sets (codebooks) with wide sector beams and narrow beams based on the orthogonality property of beamformer vectors, ii) a beamforming algorith…
Beamspace multi-input multi-output (MIMO) relying on lens antenna arrays can significantly reduce the number of radio-frequency chains in millimeter-wave (mmWave) communication systems through beam selection. However, the beamforming gain is actually frequency-dependent in wideband mmWave MIMO systems. This phenomenon is called beam squint, which will deteriorate the system's performance when traditional beam selection methods are used. To solve this problem, we propose a wideband beam selection method for mmWave MIMO systems relying on lens antenna arrays. Firstly, we select one beam with the…
Channel estimation and hybrid precoding are considered for multi-user millimeter wave massive multi-input multi-output system. A deep learning compressed sensing (DLCS) channel estimation scheme is proposed. The channel estimation neural network for the DLCS scheme is trained offline using simulated environments to predict the beamspace channel amplitude. Then the channel is reconstructed based on the obtained indices of dominant beamspace channel entries. A deep learning quantized phase (DLQP) hybrid precoder design method is developed after channel estimation. The training hybrid precoding n…
In this paper, an efficient beam and channel acquisition scheme together with joint angle-delay power profile (JADPP) construction are proposed for single-carrier mm-wave wideband sparse massive multiple-input multiple-output (MIMO) channels when hybrid beamforming architecture is utilized. We consider two different modes of operation, namely slow-time beam acquisition and fast-time instantaneous channel estimation, for training stage of time division duplex based systems. In the first mode, where pre-structured hybrid beams are formed to scan intended angular sectors, the joint angle-delay sp…
The decadal research in integrated true-time-delay arrays have seen organic growth enabling realization of wideband beamformers for large arrays with wide aperture widths. This article introduces highly reconfigurable delay elements implementable at analog or digital baseband that enables multiple SSP functions including wideband beamforming, wideband interference cancellation, and fast beam training. Details of the beam-training algorithm, system design considerations, system architecture and circuits with large delay range-to-resolution ratios are presented leveraging integrated delay compen…
In this article, we investigate channel estimation for wideband millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) under hybrid architecture with lowprecision analog-to-digital converters (ADCs). To design channel estimation for the hybrid structure, both analog processing components and frequency-selective digital combiners need to be optimized. The proposed channel estimator follows the typical linear-minimum-mean-square-error (LMMSE) structure and applies for an arbitrary channel model. Moreover, for sparsity channels as in mmWave, the proposed estimator performs more ef…
In this letter, we investigate time-domain channel estimation for wideband millimeter wave (mmWave) MIMO OFDM system. By transmitting frequency-domain pilot symbols as well as different beamforming vectors, we observe that the time-domain mmWave MIMO channels exhibit channel delay sparsity and especially block sparsity among different spatial directions. Then we propose a time-domain channel estimation exploiting block sparsity (TDCEBS) scheme, which always aims at finding the best nonzero block achieving the largest projection of the residue at each iterations. In particular, we evaluate the …
Distributed phased arrays based multiple-input multiple-output (DPA-MIMO) is a recently proposed highly reconfigurable architecture enabling both spatial multiplexing and beamforming in millimeter-wave (mmWave) systems. In this work, we focus on coping with the hybrid precoding for the wideband DPA-MIMO system with orthogonal frequency division multiplexing (OFDM) modulation. More specifically, we propose an alternating direction method of multipliers (ADMM) enabled hybrid precoding approach based on an alternating optimization framework, abbreviated to ADMM-AltMin, for such cooperative array-…
Spatial multiplexing (SMX) multiple-input multiple-output (MIMO) over the best beamspace was considered as the best solution for millimeter wave (mmWave) communications regarding spectral efficiency (SE), referred as the best beamspace selection (BBS) solution. The equivalent MIMO water-filling (WF-MIMO) channel capacity was treated as an unsurpassed SE upper bound. Recently, researchers have proposed various schemes trying to approach the benchmark and the performance bound. But, are they the real limit of mmWave MIMO systems with reduced radio-frequency (RF) chains? In this paper, we challen…
Carleton University（卡尔顿大学）；United States Army Research Laboratory（美国陆军研究实验室）
This paper addresses two major challenges in terahertz (THz) channel estimation: the beam-split phenomenon, i.e., beam misalignment because of frequency-independent analog beamformers, and computational complexity because of the usage of ultra-massive number of antennas to compensate propagation losses. Data-driven techniques are known to mitigate the complexity of this problem but usually require the transmission of the datasets from the users to a central server entailing huge communication overhead. In this work, we introduce a federated multi-task learning (FMTL), wherein the users transmi…
A major source of difficulty when operating with large arrays at mmWave frequencies is to estimate the wideband channel, since the use of hybrid architectures acts as a compression stage for the received signal. Moreover, the channel has to be tracked and the antenna arrays regularly reconfigured to obtain appropriate beamforming gains when a mobile setting is considered. In this paper, we focus on the problem of channel tracking for frequency-selective mmWave channels, and propose two novel channel tracking algorithms that leverage prior statistical information on the angles-of-arrival and an…
This paper investigates adaptive signal shaping methods for millimeter wave (mmWave) multiple-input multiple-output (MIMO) communications based on the maximizing the minimum Euclidean distance (MMED) criterion. In this work, we utilize the indices of analog precoders to carry information and optimize the symbol vector sets used for each analog precoder activation state. Specifically, we firstly propose a joint optimization based signal shaping (JOSS) approach, in which the symbol vector sets used for all analog precoder activation states are jointly optimized by solving a series of quadratical…
In this paper, the fully corrective forward greedy selection-cross validation-based (FCFGS-CV-based) channel estimator is proposed for wideband millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems with low-resolution analog-to-digital converters (ADCs). The sparse nature of the mmWave virtual channel in the angular and delay domains is exploited to convert the maximum a posteriori (MAP) channel estimation problem to an optimization problem with a concave objective function and sparsity constraint. The FCFGS algorithm, which is the generalized orthogonal matching pursu…
The best beam steering directions are estimated through beam training, which is one of the most important and challenging tasks in millimeter-wave and sub-terahertz communications. Novel array architectures and signal processing techniques are required to avoid prohibitive beam training overhead associated with large antenna arrays and narrow beams. In this work, we leverage recent developments in true-time-delay (TTD) arrays with large delay-bandwidth products to accelerate beam training using frequency-dependent probing beams. We propose and study two TTD architecture candidates, including a…
In wideband millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems, channel estimation is challenging due to the hybrid analog-digital architecture, which compresses the received pilot signal and makes channel estimation a compressive sensing (CS) problem. However, existing high-performance CS algorithms usually suffer from high complexity. On the other hand, the beam squint effect caused by huge bandwidth and massive antennas will deteriorate estimation performance. In this paper, frequency-dependent angular dictionaries are first adopted to compensate for beam squint.…
In this paper, a channel estimator for wideband millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems with hybrid architectures and low-resolution analog-to-digital converters (ADCs) is proposed. To account for the propagation delay across the antenna array, which cannot be neglected in wideband mmWave massive MIMO systems, the discrete time channel that models the spatial wideband effect is developed. Also, the training signal design that addresses inter-frame, inter-user, and inter-symbol interferences is investigated when the spatial wideband effect is not negligibl…
In millimeter-wave (mmWave) systems, beamforming is needed to overcome harsh channel environments. As a promising beamforming solution, lens antenna array (LAA) implementation can provide a cost-effective solution without notable performance degradation compared to its counterpart. However, an appropriate beam selection is a challenge since it requires efficient channel estimation via an extensive beam training process for perfect beam alignment. In this paper, we propose a high mobility beam and channel tracking algorithm based on the unscented Kalman filter (UKF) to address this challenge, w…
Millimeter-wave communications rely on beamforming gain from both transmitters and receivers to compensate for severe propagation loss. To achieve adequate gain, beam training is required to identify propagation directions. The main challenge in beam training arises from maintaining low overhead with increased array size. This paper presents a novel one-shot beam training technique that utilizes the emerging architecture of true-time-delay (TTD) arrays. We first show that TTD arrays facilitate frequency dependent beam steering. The proposed training procedure with TTD arrays then exploits this…
Millimeter-wave/Terahertz (mmW/THz) communications have shown great potential for wideband massive access in next-generation cellular internet of things (IoT) networks. To decrease the length of pilot sequences and the computational complexity in wideband massive access, this paper proposes a novel joint activity detection and channel estimation (JADCE) algorithm. Specifically, after formulating JADCE as a problem of recovering a simultaneously sparse-group and low rank matrix according to the characteristics of mmW/THz channel, we prove that jointly imposing $l_1$ norm and low rank on such a …
Accurate channel parameter estimation is challenging for wideband millimeter-wave (mmWave) large-scale hybrid arrays, due to beam squint and much fewer radio frequency (RF) chains than antennas. This paper presents a novel joint delay and angle estimation approach for wideband mmWave fully-connected hybrid uniform cylindrical arrays. We first design a new hybrid beamformer to reduce the dimension of received signals on the horizontal plane by exploiting the convergence of the Bessel function, and to reduce the active beams in the vertical direction through preselection. The important recurrenc…
In this paper, we propose and evaluate two novel double-sequence low-resolution frequency synchronization methods in millimeter-wave (mmWave) systems. In our system model, the base station uses analog beams to send the synchronization signal with infinite-resolution digital-to-analog converters. The user equipment employs a fully digital front end to detect the synchronization signal with low-resolution analog-to-digital converters (ADCs). The key ingredient of the proposed methods is the custom designed synchronization sequence pairs, from which there exists an invertible function (a ratio me…
Extremely large-scale multiple-input-multiple-output (XL-MIMO) at millimeter-wave (mmWave) and terahertz (THz) bands plays an important role in supporting extreme high beamforming gain as well as ultra-wideband spectrum resources. Unfortunately, accurate wideband XL-MIMO channel estimation suffers from the new challenge called as the near-field beam split effect. Prior works either neglect the accurate near-field channel model or fail to exploit the beam split effect, resulting in poor channel estimation accuracy for wideband XL-MIMO. To tackle this problem, this paper proposes a bilinear patt…
Aiming at maximizing the achievable sum-rate of wideband multiuser mmWave massive MIMO systems, the hybrid precoding is studied. Since each computation of the achievable sum-rate can be performed only after the analog precoder and digital precoder are both determined, the maximization of the achievable sum-rate has intractable computational complexity. By introducing the interference free (IF) achievable sum-rate, the design of the analog and digital precoders can be decoupled. To avoid the beam conflict and maximize the IF achievable sum-rate, a Hungarian-based codeword selection algorithm is…
Wideband Antenna Deconvolution for Bistatic Millimeter Wave Radar Reflectivity Measurements
Thuringian Center of Innovation in Mobility（图林根创新 mobility 中心）；Institute of Information Technology, Technische Universität Ilmenau（伊尔梅瑙工业大学信息技术研究所）；RF and Microwave Research Group, Technische Universität Ilmenau（伊尔梅瑙工业大学射频与微波研究组）
Spatial wideband effects are known to affect channel estimation and localization performance in millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems. Based on perturbation analysis, we show that the spatial wideband effect is in fact more pronounced than previously thought and significantly degrades performance, even at moderate bandwidths, if it is not properly considered in the algorithm design. We propose a novel channel estimation method based on multidimensional ESPRIT per subcarrier, combined with unsupervised learning for pairing across subcarriers, which shows…
