Developing applicable two-dimensional (2D) electrode materials with high performance, especially with high ion storage capacity, has become an ever more obsessive quest in recent years. Based on first-principles calculations, we report that T-graphene, a new carbon-based 2D material, has a record-high Li/Na storage capacity. The capacity of T-graphene is as high as 2233.2 mA h g-1 for Li, and can reach 2357.2 mA h g-1 for Na, which are 6 times as much as that of the commercial graphite and are the highest among 2D anode materials identified so far. We demonstrate that the ultrahigh storage capacity of T-graphene mostly benefits from its low atomic mass and special periodic lattice structure. T-graphene has not only the ultrahigh storage capacity but also hosts the stable ion adsorption, good electric conductivity, fast ion diffusion speed, and low open-circuit voltage, which are merits required as a superior anode material for Li-ion and Na-ion batteries with ultrahigh storage capacity.
Magnesium (Mg) metal has been widely explored as an anode material for Mg-ion batteries (MIBs) owing to its large specific capacity and dendrite-free operation. However critical challenges, such as the formation of passivation layers during battery operation and anode-electrolyte-cathode incompatibilities, limit the practical application of Mg-metal anodes for MIBs. Motivated by the promise of group XIV elements (namely Si, Ge and Sn) as anodes for lithium- and sodium-ion batteries, here we conduct systematic first principles calculations to explore the thermodynamics and kinetics of group XIV…
Inspired by the wisdom of metallurgists in designing new alloys, the Integrated Computational Materials Engineering (ICME) based design strategy is proposed for development of Si based anodes for Li-ion batteries (LIBs). The strategy starts with a rational component design of Si-X, where X is the additive component(s) helping to overcome the problems of the pure Si anodes. An optimization of the composition, structure, property and performance of the Si-X anode is followed to fulfill the requirements for its commercialization. In addition to the widely applied designing scheme for the nanostru…
Due to the rapid growth in the demand for high-energy-density Li batteries and insufficient global Li reserves, the anode-free Li metal batteries are receiving increasing attention. Various strategies, such as surface modification and structural design of Cu current collectors, have been proposed to stabilize the anode-free Li metal batteries. Unfortunately, the mechanism of Li deposition on the Cu surfaces with the different Miller indices is poorly understood, especially on the atomic scale. Here, a large-scale molecular dynamics simulation of Li deposition on the Cu substrates was performed…
We systematically evaluate the prospects of a novel 2D nanomaterial, phosphorene, as anode for Na-ion batteries. Using first-principles calculations, we determine the Na adsorption energy, specific capacity and Na diffusion barriers on monolayer phosphorene. We examine the main trends in electronic structure and mechanical properties as a function of Na concentration. We find favorable Na-phosphorene interaction with theoretical capacity, exceeding those of alternative monolayer anodes for Na-ion batteries. We find that Na-phosphorene undergoes semiconductor-metal transition at high Na concent…
There is an urgently need for the high-performance rechargeable electrical storage devices as supplement or substitutions of lithium ion batteries due to the shortage of lithium in nature. Herein we propose a stable 2D electrene T'-Ca2P as anode material for Na/K ion batteries by first-principle calculations. Our calculated results show that T'-Ca2P monolayer is an antiferromagnetic semiconducting electrene with spin-polarized electron gas. It exhibits suitable adsorption for both Na and K atoms, and its anisotropic migration energy barriers are 0.050/0.101 eV and 0.037/0.091 eV in b/a directi…
Graphyne, a single atomic layer structure of the carbon six-member rings connected by one acetilenic linkage, is a promising anode of rechargeable batteries. In this paper, a first-principle study has been carried out on graphyne as a new candidate for the anode material of magnesium-ion batteries, using density functional theory calculations. The main focus is on the magnesium adsorption on graphyne surface. The structural properties such as adsorption height and energy, the most stable adsorption sites, the Band structure and DOS of the pristine graphyne the diverse Mg-decorated graphyne str…
Hollow carbon spheres (HCS) covered with metal oxide nanoparticles (SnO2 and MnO2, respectively) were successfully synthesized and investigated regarding their potential as anode materials for lithium-ion batteries. Raman spectroscopy shows a high degree of graphitization for the HCS host structure. The mesoporous nature of the nanocomposites is confirmed by Brunauer-Emmett-Teller analysis. For both metal oxides under study, the metal oxide functionalization of HCS yields a significant increase of electrochemical performance. The charge capacity of HCS/SnO2 is 370 mAh/g after 45 cycles (266 mA…
Sodium-ion batteries (SIBs) have attracted a great deal of attention as potential low-cost energy storage alternatives to Lithium-ion batteries (LIBs) due to the intrinsic safety and great abundance of sodium on Earth. For developing competitive SIBs, highly efficient anode materials with large capacity and rapid ion diffusion are indispensable. In this study, a two-dimensional (2D) Dirac monolayer, that is borophosphene, is proposed to be a promising anode material for high performance SIBs on the basis of density functional theory calculations. The performances of Na adsorption and diffusion…
We have investigated the possibility of using aluminum functionalized silicene trilayers (ABC-Si$_4$Al$_2$) as an anode material for alkali metal ion batteries (AMIBs). First, we studied the thermodynamic stability of ABC-Si$_4$Al$_2$ using ab-initio molecular dynamics simulations, showing that this material remains stable up to 600 K. Then, we explored the properties of alkali metal atoms (Li, Na, K) adsorption in ABC-Si$_4$Al$_2$, finding several available sites with high adsorption energies. Moreover, we computed the diffusion properties of those atoms along high-symmetry paths using the nu…
Combining first-principles density functional method and crystal structure prediction techniques, we report a series of hexagonal two-dimensional (2D) transition metal borides (TMBs) including Sc2B2, Ti2B2, V2B2, Cr2B2, Y2B2, Zr2B2, and Mo2B2. Their dynamic and thermal stabilities are testified by phonon and molecular dynamics simulations. We investigate the potential of 2D Ti2B2 monolayer as the anode material for Li-ion batteries (LIBs) and Na-ion batteries (NIBs). The Ti2B2 monolayer possesses high theoretical specific capacities of 456 and 1027 mAhg-1 for Li and Na, respectively. The very …
MoO2/C-composites have been fabricated for the first time by a tartaric acid/glucose-assisted sol-gel method with post-annealing at 500 °C for 1 h in N2 flow. The synthesized materials were fully characterized with respect to structure, morphology, and electrochemical properties. Compared with tartaric acid-assisted products, the adoption of glucose as carbon source effectively increases the carbon content in the composites. Irrespective of the organic component, the composites exhibit low crystallinity and small grain size. This results in good electrochemical performance of the anode materia…
Rational design of novel two-dimensional (2D) electrode materials with high capacity is crucial for the further development of Li-ion and Na-ion batteries. Herein, based on first-principles calculations, we systemically investigate Li and Na storage behaviors in the recently discovered 2D topological nodal-loop metal - the honeycomb borophene oxide (h-B2O). We show that h-B2O is an almost ideal anode material. It has good conductivity before and after Li/Na adsorption, fast ion diffusion with diffusion barrier less than 0.5 eV, low open-circuit voltage (less than 1 V), and small lattice change…
Mg batteries utilizing a Mg metal anode with a high-voltage intercalation cathode define a potential pathway toward energy storage with high energy density. However, the realization of Mg batteries is plagued by the instability of existing electrolytes against the Mg-metal anode and high-voltage cathode materials. One viable solution to this problem is the identification of protective coating materials that could effectively separate the distinct chemistries of the metal-anode and the cathode materials from the electrolyte. Using first-principles calculations we map the electrochemical stabili…
Phosphorus is one of the most promising anodes for sodium ion batteries (SIBs). Little is known about the structural mechanism of Na/P cycling due to the fact that only one of the structures involved (Na3P) is crystalline. Using operando X-ray diffraction computed tomography (XRD-CT) analysed by Rietveld and pair distribution (PDF) methods combined with density functional theory (DFT) calculations we show that the sodiation and desodiation mechanisms of phosphorus are very different. Sodiation follows the thermodynamic path of lowest energy from P via NaP to Na3P while desodiation follows a ki…
Theoretical Studies on Sodium Storage Mechanism in Hard Carbon Anodes of Sodium-Ion Batteries: Molecular Simulations Based on Machine Learning Force Fields
We developed two-step solution-phase reactions to form hybrid materials of Mn3O4 nanoparticles on reduced graphene oxide (RGO) sheets for lithium ion battery applications. Mn3O4 nanoparticles grown selectively on RGO sheets over free particle growth in solution allowed for the electrically insulating Mn3O4 nanoparticles wired up to a current collector through the underlying conducting graphene network. The Mn3O4 nanoparticles formed on RGO show a high specific capacity up to ~900mAh/g near its theoretical capacity with good rate capability and cycling stability, owing to the intimate interacti…
Silicon suboxide is currently considered as a unique candidate for lithium ion batteries anode materials due to its considerable capacity. However, no adequate information exist about the role of oxygen content on its performance. To this aim, we used density functional theory to create silicon suboxide matrices of various Si:O ratios and investigated the role of oxygen content on the structural, dynamic, electronic properties and lithiation behavior of the matrices. Our study demonstrates that the O atoms interact strongly with the inserted Li atoms resulting in a disintegration of the host m…
Phosphorus has received recent attention in the context of high-capacity and high-rate anodes for lithium and sodium-ion batteries. Here, we present a first principles structure prediction study combined with NMR calculations which gives us insights into its lithiation/sodiation process. We report a variety of new phases phases found by AIRSS and the atomic species swapping methods. Of particular interest, a stable Na$_5$P$_4$-C2/m structure and locally stable structures found less than 10 meV/f.u. from the convex hull, such as Li$_4$P$_3$-P2$_1$2$_1$2$_1$, NaP$_5$-Pnma and Na$_4$P$_3$-Cmcm. T…
Finding electrode materials with high capacity is a key challenge for developing Lithium-ion batteries (LIBs). Graphene was once expected to be a promising candidate, but it turns out to be too inert to interact with Li. Here, by using the first-principles calculations, we predict that Germanium doped graphene, termed as Germagraphene which has been achieved in recent experiment, is a promising LIB anode material. We find that at the optimal Ge concentration, which corresponds to the chemical formula C17Ge, the specific capacity for Germagraphene can be as high as 1734 mAh/g, over four times l…
It is shown that continuously occurring electrolyte-reduction reaction on freshly-exposed electrode surfaces during lithiation/delithiation cycles causes the lowering of cycling efficiency, and hence, capacity fade in well-cycled silicon anodes in lithium-ion batteries. Using galvanostatic lithiation/delithiation data from multiple cycles on a Li/Si half-cell, a methodology to separate the charge due to the main reaction (lithiation/delithiation of Si) from the side-reaction (electrolyte-reduction) is presented. The rate of this parasitic side reaction is estimated on well-cycled amorphous sil…
Li3VO4/C composites have been synthesized by a sol-gel method and post-annealing at 650 °C for 1 h in N2 flow using either tartaric acid, malic acid, or glucose as both chelating agents and carbon source. The presence of these organic additives crucially affects morphology and crystallite size of the final product. It is found that the electrochemical properties of Li3VO4/C as anode material for Li-ion batteries (LIBs) are influenced by the morphology, texture and carbon content of the material. When using carboxylic acids as carbon source composites with mesoporous structure and a high surfac…
Using first principles structure searching with density-functional theory (DFT) we identify a novel $Fm\bar{3}m$ phase of Cu$_2$P and two low-lying metastable structures, an $I\bar{4}3d$--Cu$_3$P phase, and a $Cm$--Cu$_3$P$_{11}$ phase. The computed pair distribution function of the novel $Cm$--Cu$_3$P$_{11}$ phase shows its structural similarity to the experimentally identified $Cm$--Cu$_2$P$_7$ phase. The relative stability of all Cu--P phases at finite temperatures is determined by calculating the Gibbs free energy using vibrational effects from phonon modes at 0 K. From this, a finite-temp…
Sodium ion batteries become popular due to their low cost. Among possible anode materials of sodium ion batteries, phosphorus has great potential owing to its high theoretical capacity. Previous research that yielded high capacity and long duration of phosphorus anode used expensive materials such as black phosphorus (BP) and phosphorene. To take advantage of the low cost of sodium ion batteries, we report a simple and low-cost method to fabricate anode: condensing red phosphorus on carbon xerogel. Even with large particle size (~ 50 $μ$m) and high mass loading (2 mg cm$^{-2}$), the composite …
For a successful integration of silicon in high-capacity anodes of Li-ion batteries, its intrinsic capacity decay on cycling due to severe volume swelling should be minimized. In this work, Ni-Sn intermetallics are studied as buffering matrix during reversible lithiation of Si-based anodes. Si/Ni-Sn composites have been synthetized by mechanical milling using C and Al as process control agents. Ni3Sn4, Ni3Sn2 intermetallics and their bi-phasic mixture were used as constituents of the buffering matrix. The structure, composition and morphology of the composites have been analyzed by X-ray diffr…
We report in situ measurement of biaxial moduli of a Si thin-film electrode as a function of its lithium concentration. During lithiation, biaxial compressive stress is induced in the Si film and it undergoes plastic flow. At any state-of-charge (SOC), a relatively small delithiation-relithiation sequence unloads and reloads the film elastically. From the stress and strain changes during a delithiation-relithiation cycle, the biaxial modulus of the film is calculated. Stress change is obtained by measuring the change in substrate curvature using a Multi-beam Optical Sensor; the elastic strain …
Conditional spinodal decomposition in Li-Mg anodes for lithium metal batteries
Max Planck Institute for Sustainable Materials（马克斯·普朗克可持续材料研究所）；Aeronautics Institute of Technology（航空技术学院）；Université de Picardie Jules Verne（亚眠儒勒·凡尔纳大学）；University Grenoble Alpes, CNRS, Grenoble INP, SIMAP（格勒诺布尔阿尔卑斯大学，法国国家科学研究中心，格勒诺布尔理工学院，SIMAP）；Thermo-Calc Software AB（Thermo-Calc软件有限公司）；Federal University of São Carlos（圣卡洛斯联邦大学）；Korea University（高丽大学）；Univ Rouen Normandie, CNRS, INSA Rouen Normandie, Groupe de Physique des Matériaux, UMR 6634（鲁昂诺曼底大学，法国国家科学研究中心，鲁昂诺曼底国立应用科学学院，材料物理研究组）
Recently "carbon ene-yne" (CEY), a novel full carbon two-dimensional (2D) material was successfully synthesized by the solvent-phase reaction. Motivated by this experimental effort, we conducted extensive first-principles density functional theory simulations to explore the application prospects of CEY as an anode material for Mg, Na and Li-ion batteries. To simulate the ionic intercalation process in an anode electrode, the adatoms coverage was gradually increased. We then employed Bader charge analysis to evaluate the charge transfer between the adatoms and the CEY nanosheet and finally to r…
The abundance of Sodium (Na), its low-cost, and low reduction potential provide a lucrative inexpensive, safe, and environmentally benign alternative to Lithium Ion Batteries (LIBs). The significant challenges in advancing Sodium Ion Battery (NIB) technologies lies in finding the better electrode materials. Experimental investigations revealed the real potency of Germanium (Ge) as suitable anode materials for NIBs. However, a systematic atomistic study is necessary to understand the fundamental aspects of capacity-voltage correlation, microstructural changes of Ge, as well as diffusion kinetic…
Employing two-dimensional (2D) materials as anodes for lithium-ion batteries (LIBs) is believed to be an effective approach to meet the growing demands of high-capacity next-generation LIBs. In this work, the first-principles density functional theory (DFT) calculations are employed to evaluate the potential application of two-dimensional phosphorus carbide (2D PCx, x=2, 5, and 6) monolayers as anode materials for lithium-ion batteries. The 2D PCx systems are predicted to show outstanding structural stability and electronic properties. From the nudge elastic band calculations, the Li atoms sho…
Identifying applicable anode materials is a significant task for Li- and Na-ion battery (LIB and NIB) technologies. We propose the GaN monolayer (2D GaN) can be a good anode candidate. The GaN monolayer manifests stable Li/Na adsorption and inherently low theoretical voltages. Most excitingly, both high storage capacity and extremely fast Li/Na diffusion can be simultaneously realized in the GaN monolayer. For Li, the storage capacity and diffusion barrier is 938 mA h g-1 and 80 meV , respectively. And the values for Na are 625 mA h g-1 and 22 meV. Comparing with known 2D anode materials with …
Cycling efficiency and rate capability of porous copper-coated, amorphous silicon thin-film negative electrodes are compared to equivalent silicon thin-film electrodes in lithium-ion batteries. The presence of a copper layer coated on the active material plays a beneficial role in increasing the cycling efficiency and the rate capability of silicon thin-film electrodes. Between 3C and C/8 discharge rates, the available cell energy decreased by 8% and 18% for 40 nm copper-coated silicon and equivalent silicon thin-film electrodes, respectively. Copper-coated silicon thin-film electrodes also sh…
Effective passivation of lithium metal surfaces, and prevention of battery-shorting lithium dendrite growth, are critical for implementing lithium-metal-anodes for batteries with increased power densities. Nanoscale surface heterogeneities can be "hot spots" where anode passivation breaks down. Motivated by the observation of lithium dendrites in pores and grain boundaries in all-solid batteries, we examine lithium metal surfaces covered with Li(2)O and/or LiF thin films with grain boundaries in them. Electronic structure calculations show that, at >0.25 V computed equilibrium overpotential, L…
A rechargeable lithium metal battery (LMB), which uses metallic lithium at the anode, is among the most promising technologies for next generation electrochemical energy storage devices due to its high energy density, particularly when Li is paired with energetic conversion cathodes such as sulfur, oxygen/air, and carbon dioxide. Practical LMBs in any of these designs remain elusive due to multiple stubborn problems, including parasitic reactions of Li metal with liquid electrolytes, unstable/dendritic electrodeposition at the anode during cell recharge, and chemical reaction of dissolved cath…
Thick Li-ion battery electrodes with high ion transport rates could enable batteries that cost less and that have higher gravimetric and volumetric energy density, because they require fewer inactive cell-components. Finding ways to increase ion transport rates in thick electrodes would be especially valuable for electrodes made with graphite platelets, which have been shown to have tortuosities in the thru-plane direction about 3 times higher than in the in-plane direction. Here, we predict that bi-tortuous electrode structures (containing electrolyte-filled macro-pores embedded in micro-poro…
Li-ion rechargeable batteries have enabled the wireless revolution transforming global communication. Future challenges, however, demands distributed energy supply at a level that is not feasible with the current energy-storage technology. New materials, capable of providing higher energy density are needed. Here we report a new class of lithium-ion batteries based on a graphene ink anode and a lithium iron phosphate cathode. By carefully balancing the cell composition and suppressing the initial irreversible capacity of the anode, we demonstrate an optimal battery performance in terms of spec…
In view of the long-standing controversy over the reversibility of transition metals in Sn-based alloys as anode for Li-ion batteries, an in situ real-time magnetic monitoring method was used to investigate the evolution of Sn-Co intermetallic during the electrochemical cycling. Sn-Co alloy film anodes with different compositions were prepared via magnetron sputtering without using binders and conductive additives. The magnetic responses showed that the Co particles liberated by Li insertion recombine fully with Sn during the delithiation to reform Sn-Co intermetallic into stannum richer phase…
We present ab initio studies of structures, energetics, and diffusion properties of Mg in Si, Ge, and Sn diamond structures to evaluate their potential as insertion type anode materials for Mg batteries. We show that Si could provide the highest specific capacities (3817 mAh g-1) and the lowest average insertion voltage (~0.15 eV vs. Mg) for Mg storage. Nevertheless, due to its significant percent lattice expansion (~216%) and slow Mg diffusion, Sn and Ge are more attractive; both anodes have lower lattice expansions (~120 % and ~178 %, respectively) and diffusion barriers (~0.50 and ~0.70 eV,…
The capacity and stability of constituent electrodes determine the performance of Li-ion batteries. In this study, density functional theory is employed to explore the potential application of recently synthesized two dimensional phosphorene as electrode materials. Our results show that Li atoms can bind strongly with phosphorene monolayer and double layer with significant electron transfer. Besides, the structure of phosphorene is not much influenced by lithiation and the volume change is only 0.2\%. A semiconducting to metallic transition is observed after lithiation. The diffusion barrier i…
Embedding silicon nanoparticles in an intermetallic matrix is a promising strategy to produce remarkable bulk anode materials for lithium-ion (Li-ion) batteries with low potential, high electrochemical capacity and good cycling stability. These composite materials can be synthetized at a large scale using mechanical milling. However, for Si-Ni3Sn4 composites, milling also induces a chemical reaction between the two components leading to the formation of free Sn and NiSi2, which is detrimental to the performance of the electrode. To prevent this reaction, a modification of the surface chemistry…
Sodium ion batteries (SIBs) are considered as an efficient alternative for lithium-ion batteries (LIBs) owing to the natural abundance and low cost of sodium than lithium. In this context, the anode materials play a vital role in rechargeable batteries to acquire high energy and power density. In order to demonstrate transition metal dichalcogenide (TMD) as potential anode materials, we have synthesized MoSeTe sample by conventional flux method, and the structure and morphology are characterized using x-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), transmission el…
Bismuth has recently attracted interest in connection with Na-ion battery anodes due to its high volumetric capacity. It reacts with Na to form Na$_3$Bi which is a prototypical Dirac semimetal with a nontrivial electronic structure. Density-functional-theory based first-principles calculations are playing a key role in understanding the fascinating electronic structure of Na$_3$Bi and other topological materials. In particular, the strongly-constrained-and-appropriately-normed (SCAN) meta-generalized-gradient-approximation (meta-GGA) has shown significant improvement over the widely used gener…
The development of silicon anodes to replace conventional graphite in efforts to increase energy densities of lithium-ion batteries has been largely impeded by poor interfacial stability against liquid electrolytes. Here, stable operation of 99.9 weight% micro-Si (uSi) anode is enabled by utilizing the interface passivating properties of sulfide based solid-electrolytes. Bulk to surface characterization, as well as quantification of interfacial components showed that such an approach eliminates continuous interfacial growth and irreversible lithium losses. In uSi || layered-oxide full cells, h…
Spatially-resolved neutron powder diffraction with gauge volume 2x2x20 mm3 has been applied to probe the lithium concentration in the graphite anode of different Li-ion cells of 18650-type in situ in charged state. Structural studies performed in combination with electrochemical measurements and X-ray computed tomography under real cell operating conditions unambiguously revealed non-homogeneity of lithium distribution in the graphite anode. Deviations from a homogeneous behaviour have been found in both radial and axial directions of 18650-type cells and were discussed in the frame of cell ge…
Lithium-graphite intercalation compounds (Li-GICs) are the most common anode material for modern Li-ion batteries. However, the dielectric response of this material in the electrostatic limit (and its variation with the state of charge (SOC)) has not been investigated to a satisfactory degree, especially not for the higher SOC range. Nevertheless, said dielectric behaviour is a highly desired property, particularly as an input parameter for charged kinetic Monte Carlo simulations, one of the most promising modeling techniques for energy materials. In this work, we employ our recent DFTB parame…
Using density functional calculations, we examine insertion/extraction of Mg ions in Mg3Bi2, an interesting Mg-ion battery anode. We found that a (1 1 0) facet is the most stable termination. Vacating a Mg2+ ion from the octahedral site is more favourable for both surface and bulk regions of the material. However, the diffusion barriers among the tetrahedral sites are around 3 times smaller than those among octahedral sites. Consequently, during the magnesiation/demagnesiation process, Mg ions first vacate the octahedral sites and then diffuse through the tetrahedral sites. The spin-orbit inte…
