In recent years, the lattice Boltzmann (LB) method has been widely employed to simulate boiling phenomena [A. Márkus and G. Házi, Phys. Rev. E 83, 046705 (2011); Biferale et al., Phys. Rev. Lett. 108, 104502 (2012); Li et al., Phys. Rev. E 96, 063303 (2017); Wu et al., Int. J. Heat Mass Transfer 126, 773 (2018)]. However, a very important issue still remains open, i.e., how does boiling occur in the LB simulations? For instance, the existing LB studies showed that the boiling on a hydrophobic surface begins at a lower wall superheat than that on a hydrophilic surface, which qualitatively agrees well with experimental studies, but no one has yet explained how this phenomenon appears in the LB simulations and what happened in the simulations after changing the wettability of the heating surface. In this paper, the LB boiling mechanism is revealed by analyzing boiling on a flat surface with mixed wettability and boiling on a structured surface with homogeneous wettability. Through a theoretical analysis, we demonstrate that, when the same wall superheat is applied, in the LB boiling simulations the fluid density near the heating surface decreases faster on a hydrophobic surface than that on a hydrophilic surface. Accordingly, a lower wall superheat can induce the phase transition from liquid to vapor on a hydrophobic surface than that on a hydrophilic surface. Furthermore, a similar theoretical analysis shows that the fluid density decreases fastest at concave corners in the case of a structured surface with homogeneous wettability, which explains why vapor bubbles are nucleated at concave corners in the LB simulations of boiling on structured surfaces.
Pool boiling characteristics in two computational domains with and without considering conjugate heat transfer (CHT) were numerically simulated by an improved hybrid pseudopotential phase-change lattice Boltzmann method (LBM). The effects of constant temperature boundary condition (BC) with nucleate spots and fluctuant temperature on the boiling process were investigated in detail. It was found that for the computational domain without CHT, the treatment of constant temperature BC with nucleate spots is quite easier to produce film boiling than the temperature BC with small fluctuation. Howeve…
A hybrid thermal lattice Boltzmann (LB) model is presented to simulate thermal multiphase flows with phase change based on an improved pseudopotential LB approach [Q. Li, K. H. Luo, and X. J. Li, Phys. Rev. E 87, 053301 (2013)]. The present model does not suffer from the spurious term caused by the forcing-term effect, which was encountered in some previous thermal LB models for liquid-vapor phase change. Using the model, the liquid-vapor boiling process is simulated. The boiling curve together with the three boiling stages (nucleate boiling, transition boiling, and film boiling) is numericall…
A hybrid thermal lattice Boltzmann phase-change model was performed to simulate the pool boiling above a smooth horizontal heater. The effects of homogenous and heterogeneous wettability on entire boiling curves from the onset of nucleate boiling (ONB) to fully developed film boiling were investigated comprehensively. Results show that concerning the homogeneous and hydrophilic heater, increasing the wall wettability results in a high critical heat flux (CHF) and yields a rightward and upward shift of the boiling curve. It is also found that decreasing the wettability promotes the occurrence o…
When boiling occurs in a liquid flow field, the phenomenon is known as forced-convection boiling. We numerically investigate such a boiling system on a cylinder in a flow at a saturated condition. To deal with the complicated liquid-vapor phase-change phenomenon, we develop a numerical scheme based on the pseudopotential lattice Boltzmann method (LBM). The collision stage is performed in the space of central moments (CMs) to enhance numerical stability for high Reynolds numbers. The adopted forcing scheme, consistent with the CMs-based LBM, leads to a concise yet robust algorithm. Furthermore,…
In this paper, the energy non-conservation problem of the hybrid thermal LB phase change model is emphasized. To solve this problem, an infinite volume discrete scheme is introduced to deal with the diffusion term in the energy equation. After verified this model with energy conservation law in the simulation of the one-dimensional heat conduction across the liquid-vapor interface and the liquid film evaporation on the heating wall, the improved hybrid thermal LB model is then applied in the simulation of bubble nucleation and boiling heat transfer. With an innovative nucleation site treatment…
In this paper, by using a phase-change lattice Boltzmann (LB) model coupled with an electric field model, we numerically investigate the performance and enhancement mechanism of pool boiling of dielectric fluids on pillar-structured surfaces under an electric field. The numerical investigation reveals that applying an electric field causes both positive and negative influences on the pool boiling of dielectric fluids on pillar-structured surfaces. It is found that, under the action of an electric field, the electric force prevents the bubbles nucleated in the channels from crossing the edges o…
Boiling is a complex phenomenon where different non-linear physical interactions take place and for which the quantitative modeling of the mechanism involved is not fully developed yet. In the last years, many works have been published focusing on the numerical analysis of this problem. However, a lack of numerical works assessing quantitatively the sensitivity of these numerical simulations to grid parameters can be identified, especially for the Lattice Boltzmann method (LBM). The main goal of this work is to propose a mesh refinement methodology for simulating phase-change heat transfer pro…
The combination of microstructures and mixed wettability for enhancing nucleate boiling has attracted much attention in recent years. However, in the existing experimental and numerical studies, the tops of microstructures are entirely subjected to wettability modification, which makes the influences of mixed wettability dependant on the characteristic length of microstructures. In order to disclose the joint effects of surface structure and mixed wettability on nucleate boiling, in this work we propose an improved type of pillar-textured surface with mixed wettability, in which the tops of sq…
We present a novel lattice Boltzmann method that has a capability of simulating thermodynamic multiphase flows. This approach is fully thermodynamically consistent at the macroscopic level. Using this new method, a liquid-vapor boiling process, including liquid-vapor formation and coalescence together with a full coupling of temperature, is simulated for the first time.
Nucleate boiling heat transfer (NBHT) from enhanced structures is an effective way to dissipate high heat flux. In the present study, the cavities behaviours for nucleation on roughened surface are numerically studied on the entire ebullition cycle based on a phase-change lattice Boltzmann method without introducing any artificial disturbances. The adopted model is firstly validated with the Laplace law and the two phase coexistence curve, and then applied to investigate the effects of cavity structure on NBHT. The bubble departure diameter, departure frequency and total boiling heat flux of a…
Direct simulations of phase-change and phase-ordering phenomena are becoming more common. Recently qualitative simulations of boiling phenomena have been undertaken by a large number of research groups. One seldom discussed limitations is that large values of gravitational forcing are required to simulate the detachment and rising of bubbles formed at a bottom surface. The forces are typically so large that neglecting the effects of varying pressure in the system becomes questionable. In this paper we examine the effect of large pressure variations induced by gravity using pseudopotential latt…
Present study explores the capability of the pseudopotential-based thermal lattice Boltzmann (LB) model in emulating the underlying thermohydrodynamics of flow boiling in a narrow fluidic channel. In contrary to the conventional Eulerian-averaging-based approach, it adheres to the mesoscopic Boltzmann statistical averaging, which allows natural phase separation and no need of assuming the initial interface. A narrow fluidic channel, with specified inlet temperature and flow rate, and exit pressure, housing a microheater at the bottom wall is considered as the computational domain of interest. …
We present high resolution numerical simulations of convection in multiphase flows (boiling) using a novel algorithm based on a Lattice Boltzmann method. We first validate the thermodynamical and kinematical properties of the algorithm. Then, we perform a series of 3d numerical simulations at changing the mean properties in the phase diagram and compare convection with and without phase coexistence at $Ra \sim 10^7$. We show that in presence of nucleating bubbles non-Oberbeck Boussinesq effects develops, mean temperature profile becomes asymmetric, heat-transfer and heat-transfer fluctuations …
Numerical codes using the Lattice Boltzmann Methods (LBM) for simulating one- or two-phase flows are widely compiled and run on graphical process units. However, those computational units necessitate to re-write the program by using a low-level language which is suited to those architectures (e.g. CUDA for GPU NVIDIA or OpenCL). In this paper we focus our effort on the performance portability of LBM i.e. the possibility of writing LB algorithms with a high-level of abstraction while remaining efficient on a wide range of architectures such as multicores x86, GPU NVIDIA, ARM, and so on. For suc…
We apply lattice Boltzmann methods to study the relaxation of the velocity profile in binary fluids under shear during spinodal decomposition. In simple fluids, when a shear flow is applied on the boundaries of the system, the time required to obtain a triangular profile is inversely proportional to the viscosity and proportional to the square of the size of the system. We find that the same behaviour also occurs for binary mixtures, for any component ratio in the mixture and independently from the time when shear flow is switched on during phase separation.
The present work is dedicated to a better understanding of the stability properties of regularized lattice Boltzmann (LB) schemes. To this extent, linear stability analyses of two-dimensional models are proposed: the standard Bhatnagar-Gross-Krook (BGK) collision model, the original pre-collision regularization and the recursive regularized model, where off-equilibrium distributions are partially computed thanks to a recursive formula. A systematic identification of the physical content carried by each LB mode is done by analyzing the eigenvectors of the linear systems. Stability results are t…
The present study focuses on the unphysical effects induced by the use of non-uniform grids in the lattice Boltzmann method. In particular, the convection of vortical structures across a grid refinement interface is likely to generate spurious noise that may impact the whole computation domain. This issue becomes critical in the case of aeroacoustic simulations, where accurate pressure estimations are of paramount importance. The purpose of this article is to identify the issues occurring at the interface and to propose possible solutions yielding significant improvements for aeroacoustic simu…
Wall-driven flow in square cavity has been studied extensively, yet it is more frequently for the rectangular cavity flow occurring in practical problems, and some flow characteristics about rectangular cavity have not been fully investigated. As a promising numerical simulation tool, the Lattice Boltzmann Method (LBM) is employed to simulate the lid-driven flow in a two-dimensional rectangular cavity in this paper. First, the code is validated for the standard square cavity, the velocity profiles, stream function values and center positions of the primary and second vortexes at different Re a…
Immiscible fluid displacement in porous media occurs in several natural and industrial processes. For example, during petroleum extraction from porous rock reservoirs, water is used to displace oil. In this paper, we investigate primary drainage and imbibition in a heterogeneous porous medium using an improved numerical model based on the multicomponent pseudopotential lattice Boltzmann method. We apply recent developments from the literature and develop new pressure boundary conditions. We show that the proposed model is able to simulate realistic viscosity ratios, and it allows independent t…
The performances of the Color-Gradient (CG) and of the Shan-Chen (SC) multicomponent Lattice Boltzmann models are quantitatively compared side-by-side on multiple physical flow problems where breakup, coalescence and contraction of fluid ligaments are important. The flow problems are relevant to microfluidic applications, jetting of microdroplets as seen in inkjet printing, as well as emulsion dynamics. A significantly wider range of parameters is shown to be accessible for CG in terms of density-ratio, viscosity-ratio and surface tension values. Numerical stability for a high density ratio $\…
Most Computational Fluid Dynamics (CFD) studies of hemodynamics in intracranial aneurysms are based on the assumption of laminar flow due to a relatively low (below 500) parent artery Reynolds number. A few studies have recently demonstrated the occurrence of transitional flow in aneurysms, but these studies employed special finite element schemes tailored to capture transitional nature of flow. In this study we investigate the occurrence of transition using a standard Lattice Boltzmann method (LBM). The LBM is used because of its computational efficiency, which in the present study allowed us…
We numerically study the dynamics of quasi-two dimensional cholesteric liquid crystal droplets in the presence of a time-dependent electric field, rotating at constant angular velocity. A surfactant sitting at droplet interface is also introduced to prevent droplet coalescence. The dynamics is modeled following a hybrid numerical approach, where a standard lattice Boltzmann technique solves the Navier-Stokes equation and a finite difference scheme integrates the evolution equations of liquid crystal and surfactant. Our results show that, once the field is turned on, the liquid crystal rotates …
Electrolyte filling is a time-critical step during battery manufacturing that also affects the battery performance. The underlying physical phenomena during filling mainly occur on the pore scale and are hard to study experimentally. In this paper, a computational approach, i.e.\ the lattice Boltzmann method, is used to study the filling process and corresponding pore-scale phenomena in 3D lithium-ion battery cathodes. The electrolyte flow through the nanoporous binder is simulated using a homogenization approach. Besides the process time, the influence of structural and physico-chemical prope…
We use free energy lattice Boltzmann methods (FRE LBM) to simulate shear and extensional flow of a binary mixture in two and three dimensions. To this end, two classical configurations are digitally twinned, namely a parallel-band device for binary shear flow and a four-roller apparatus for binary extensional flow. The FRE LBM and the test cases are implemented in the open-source C++ framework OpenLB and evaluated for several non-dimensional numbers. Characteristic deformations are captured, where breakup mechanisms occur for critical capillary regimes. Though the known mass leakage for small …
In this paper, the pinning and depinning mechanism of the contact line during droplet evaporation on chemically stripe-patterned surfaces is numerically investigated using a thermal multiphase lattice Boltzmann (LB) model with liquid-vapor phase change. A local force balance in the context of diffuse interfaces is introduced to explain the equilibrium states of droplets on chemically patterned surfaces. It is shown that, when the contact line is pinned on a hydrophobic-hydrophilic boundary, different contact angles can be interpreted as the variation of the length of the contact line occupied …
Exploring the hydrodynamic boundary of a surface by approaching a colloidal sphere and measuring the occurring drag force is a common experimental technique. However, numerous parameters like the wettability and surface roughness influence the result. In experiments these cannot be separated easily. For a deeper understanding of such surface effects a tool is required that predicts the influence of different surface properties. In this paper we present computer simulations based on the lattice Boltzmann method of a sphere submerged in a Newtonian liquid. We show that our method is able to repr…
Shan-Chen model is a numerical scheme to simulate multiphase fluid flows using Lattice Boltzmann approach. The original Shan-Chen model suffers from inability to accurately predict behavior of air bubbles interacting in a non-aqueous fluid. In the present study, we extended the Shan-Chen model to take the effect of the attraction-repulsion barriers among bubbles in to account. The proposed model corrects the interaction and coalescence criterion of the original Shan-Chen scheme in order to have a more accurate simulation of bubbles morphology in a metal foam. The model is based on forming a th…
In this work we want to simulate with the Lattice-Boltzmann method in 2D the capillary infiltration into porous structures obtained from the packing of particles. The experimental problem motivating our work is the densification of carbon preforms by reactive melt infiltration. The aim is to determine optimization principles for the manufacturing of high-performance ceramics. Simulations are performed for packings with varying structural properties. Our analysis suggests that the observed slow infiltrations can be ascribed to interface dynamics. Pinning represents the primary factor retarding …
A three-dimensional color-fluid lattice Boltzmann model for immiscible two-phase flows is developed in the framework of a three-dimensional 27-velocity (D3Q27) lattice. The collision operator comprises the D3Q27 versions of three sub-operators: a multiple-relaxation-time (MRT) collision operator, a generalized Liu--Valocchi--Kang perturbation operator, and a Latva-Kokko--Rothman recoloring operator. A D3Q27 version of an enhanced equilibrium distribution function is also incorporated into this model to improve the Galilean invariance. Three types of numerical tests, namely, a static droplet, a…
The tumbling to tank-treading (TB-TT) transition for red blood cells (RBCs) has been widely investigated, with a main focus on the effects of the viscosity ratio $λ$ (i.e., the ratio between the viscosities of the fluids inside and outside the membrane) and the shear rate $\dotγ$ applied to the RBC. However, the membrane viscosity $μ_m$ plays a major role in a realistic description of RBC's dynamics, and only a few works have systematically focused on its effects on the TB-TT transition. In this work, we provide a parametric investigation on the effect of membrane viscosity $μ_m$ on the TB-TT …
It is widely recognized that the structure of porous media is of relevance for a variety of mechanical and physical phenomena. The focus of the present work is on capillarity, a pore-scale process occurring at the micron scale. We attempt to characterize the influence of pore shape for capillary infiltration by means of Lattice Boltzmann simulations in 2D with reactive boundaries leading to surface growth and ultimately to pore closure. The systems under investigation consist of single channels with different simplified morphologies: namely, periodic profiles with sinusoidal, step-shaped and z…
Fluid dynamics simulations with the lattice Boltzmann method (LBM) are very memory-intensive. Alongside reduction in memory footprint, significant performance benefits can be achieved by using FP32 (single) precision compared to FP64 (double) precision, especially on GPUs. Here, we evaluate the possibility to use even FP16 and Posit16 (half) precision for storing fluid populations, while still carrying arithmetic operations in FP32. For this, we first show that the commonly occurring number range in the LBM is a lot smaller than the FP16 number range. Based on this observation, we develop nove…
Thermal flows characterized by high Prandtl number are numerically challenging as the transfer of momentum and heat occurs at different time scales. To account for very low thermal conductivity and obey the Courant-Friedrichs-Lewy condition, the numerical diffusion of the scheme has to be reduced. As a consequence, the numerical artefacts are dominated by dispersion errors commonly known as wiggles. In this study, we explore possible remedies in the framework of the lattice Boltzmann method by applying novel collision kernels, lattices with a large number of discrete velocities, namely D3Q27, …
The characteristics of the hydro-thermal flow which occurs when a cold fluid is injected into a hot fractured bedrock depend on the morphology of the fracture. We consider a sharp triangular asperity, invariant in one direction, perturbing an otherwise flat fracture. We investigate its influence on the macroscopic hydraulic transmissivity and heat transfer efficiency, at fixed low Reynolds number. In this study, numerical simulations are done with a coupled lattice Boltzmann method that solves both the complete Navier-Stokes and advection-diffusion equations in three dimensions. The results ar…
Gas slippage occurs when the mean free path of the gas molecules is in the order of the characteristic pore size of a porous medium. This phenomenon leads to the Klinkenberg's effect where the measured permeability of a gas (apparent permeability) is higher than that of the liquid (intrinsic permeability). A generalized lattice Boltzmann model is proposed for flow through porous media that includes Klinkenberg's effect, which is based on the model of Guo et al. (Z.L. Guo et al., Phys.Rev.E 65, 046308 (2002)). The second-order Beskok and Karniadakis-Civan's correlation (A. Beskok and G. Karniad…
