Millimeter Wave (mmWave) communications with full-duplex (FD) have the potential of increasing the spectral efficiency, relative to those with half-duplex. However, the residual self-interference (SI) from FD and high pathloss inherent to mmWave signals may degrade the system performance. Meanwhile, hybrid beamforming (HBF) is an efficient technology to enhance the channel gain and mitigate interference with reasonable complexity. However, conventional HBF approaches for FD mmWave systems are based on optimization processes, which are either too complex or strongly rely on the quality of channel state information (CSI). We propose two learning schemes to design HBF for FD mmWave systems, i.e., extreme learning machine based HBF (ELM-HBF) and convolutional neural networks based HBF (CNN-HBF). Specifically, we first propose an alternating direction method of multipliers (ADMM) based algorithm to achieve SI cancellation beamforming, and then use a majorization-minimization (MM) based algorithm for joint transmitting and receiving HBF optimization. To train the learning networks, we simulate noisy channels as input, and select the hybrid beamformers calculated by proposed algorithms as targets. Results show that both learning based schemes can provide more robust HBF performance and achieve at least 22.1% higher spectral efficiency compared to orthogonal matching pursuit (OMP) algorithms. Besides, the online prediction time of proposed learning based schemes is almost 20 times faster than the OMP scheme. Furthermore, the training time of ELM-HBF is about 600 times faster than that of CNN-HBF with 64 transmitting and receiving antennas.
This work develops LoneSTAR, a novel enabler of full-duplex millimeter wave (mmWave) communication systems through the design of analog beamforming codebooks. LoneSTAR codebooks deliver high beamforming gain and broad coverage while simultaneously reducing the self-interference coupled by transmit and receive beams at a full-duplex mmWave transceiver. Our design framework accomplishes this by tolerating some variability in transmit and receive beamforming gain to strategically shape beams that reject self-interference spatially while accounting for digitally-controlled analog beamforming netwo…
We study the beamforming optimization for an intelligent reflecting surface (IRS)-aided full-duplex (FD) communication system in this letter. Specifically, we maximize the sum rate of bi-directional transmissions by jointly optimizing the transmit beamforming and the beamforming of the IRS reflection. A fast converging alternating algorithm is developed to tackle this problem. In each iteration of the proposed algorithm, the solutions to the transmit beamforming and the IRS reflect beamforming are obtained in a semi-closed form and a closed form, respectively. Compared to an existing method ba…
We consider an integrated access and backhaul (IAB) node operating in full-duplex (FD) mode. We analyze simultaneous transmission from the New Radio gNB to the IAB node on the backhaul uplink, IAB node to a user equipment (UE) on the access downlink, and IAB transmitter to the IAB receiver on the self-interference (SI) channel. Our contributions include (1) a low complexity algorithm to jointly design the hybrid analog/digital beamformers for all three nodes to maximize the sum spectral efficiency of the access and backhaul links by canceling SI and maximizing received power; (2) derivation of…
In this letter, we study the reconfigurable intelligent surfaces (RIS) aided full-duplex (FD) communication system. By jointly designing the active beamforming of two multi-antenna sources and passive beamforming of RIS, we aim to maximize the energy efficiency of the system, where extra self-interference cancellation power consumption in FD system is also considered. We divide the optimization problem into active and passive beamforming design subproblems, and adopt the alternative optimization framework to solve them iteratively. Dinkelbach's method is used to tackle the fractional objective…
Full Duplex (FD) communication can revolutionize wireless communications as it avoids using independent channels for bi-directional communications. This work generalizes the point-to-point FD communication in millimeter wave (mmWave) band consisting of K-pairs of massive MIMO FD nodes operating simultaneously. We present a novel joint hybrid beamforming (HYBF) and combining scheme for weighted sum-rate (WSR) maximization to enable the coexistence of massive MIMO FD links cost-efficiently. The proposed algorithm relies on alternative optimization based on the minorization-maximization method. M…
The wide bandwidths offered at millimeter-wave (mmWave) frequencies have made them an attractive choice for future wireless communication systems. Recent works have presented beamforming strategies for enabling in-band full-duplex (FD) capability at mmWave even under the constraints of hybrid beamforming, extending the exciting possibilities of next-generation wireless. Existing mmWave FD designs, however, do not consider frequency-selective mmWave channels. Wideband communication at mmWave suggests that frequency-selectivity will likely be of concern since communication channels will be on th…
There have been recent works on enabling in-band full-duplex operation using millimeter-wave (mmWave) transceivers. These works are based solely on creating sufficient isolation between a transceiver's transmitter and receiver via multiple-input multiple-output (MIMO) precoding and combining. In this work, we propose supplementing these beamforming strategies with analog self-interference cancellation (A-SIC). By leveraging A-SIC, a portion of the self-interference is cancelled without the need for beamforming, allowing for more optimal beamforming strategies to be used in serving users. We us…
Full-duplex (FD) systems gained enormous attention because of the potential to double the spectral efficiency. In the context of 5G technology, FD systems operating at millimeter-wave (mmWave) frequencies become one of the most promising solutions to further increase the spectral efficiency and reduce the latency. However, such systems are vulnerable to the self-interference (SI) that significantly degrades the performance. To overcome this shortcoming, analog-only beamforming techniques have been developed to mitigate the SI. Because of the huge power consumption, systems operating at mmWave …
Equipping millimeter wave (mmWave) systems with full-duplex capability would accelerate and transform next-generation wireless applications and forge a path for new ones. Full-duplex mmWave transceivers could capitalize on the already attractive features of mmWave communication by supplying spectral efficiency gains and latency improvements while also affording future networks with deployment solutions in the form of interference management and wireless backhaul. Foreseeable challenges and obstacles in making mmWave full-duplex a reality are presented in this article along with noteworthy unkn…
Although the hardware complexity of the analog self-interference canceller in full duplex Multiple Input Multiple Output (MIMO) designs does not necessarily scale with the number of transceiver antennas, exploiting the benefits of analog cancellation in massive MIMO systems with hundreds of antenna elements is still quite impractical. Hybrid Analog and Digital (A/D) beamforming architectures have been lately considered as a candidate technology for realizing massive MIMO transceivers with very large number of antenna elements, but with much fewer numbers of Radio Frequency (RF) chains. In this…
In recent years, there has been extensive research on millimeter-wave (mmWave) communication and on in-band full-duplex (FD) communication, but work on the combination of the two is relatively lacking. FD mmWave systems could offer increased spectral efficiency and decreased latency while also suggesting the redesign of existing mmWave applications. While FD technology has been well-explored for sub-6 GHz systems, the developed methods do not translate well to mmWave. This turns us to a method called beamforming cancellation (BFC), where the highly directional mmWave beams are steered to mitig…
Full-duplex (FD) systems have the capability to transmit and receive at the same time in the same frequency band. FD systems can reduce congestion and latency and improve coverage and spectral efficiency. As a relay, they can increase range and decrease outages. Full-duplex (FD) wireless systems have been emerging as a practical solution to provide high bandwidth, low latency, and big data processing in millimeter wave and Terahertz systems to support cellular networks, autonomous driving, platooning, advanced driving assistance and other systems. However, FD systems suffer from loopback self-…
In this paper, we focus on reduced complexity full duplex Multiple-Input Multiple-Output (MIMO) systems and present a joint design of digital transmit and receive beamforming with Analog and Digital (A/D) self-interference cancellation. We capitalize on a recently proposed multi-tap analog canceller architecture, whose number of taps does not scale with the number of transceiver antennas, and consider practical transmitter impairments for the full duplex operation. Particularly, transmitter IQ imbalance and nonlinear power amplification are assumed via relevant realistic models. Aiming at supp…
Beamforming design has been widely investigated for integrated sensing and communication (ISAC) systems with full-duplex (FD) sensing and half-duplex (HD) communication. To achieve higher spectral efficiency, in this paper, we extend existing ISAC beamforming design by considering the FD capability for both radar and communication. Specifically, we consider an ISAC system, where the base station (BS) performs target detection and communicates with multiple downlink users and uplink users reusing the same time and frequency resources. We jointly optimize the downlink dual-functional transmit si…
In this article, we study the joint communication and sensing (JCAS) paradigm in the context of millimeter-wave (mm-wave) mobile communication networks. We specifically address the JCAS challenges stemming from the full-duplex operation and from the co-existence of multiple simultaneous beams for communications and sensing purposes. To this end, we first formulate and solve beamforming optimization problems for hybrid beamforming based multiuser multiple-input and multiple-output JCAS systems. The cost function to be maximized is the beamformed power at the sensing direction while constraining…
In this paper, a novel full-duplex non-coherent (FD-NC) transmission scheme is developed for massive multiple-input multiple-output (mMIMO) systems using analog beamforming (ABF). We propose to use a structured Grassmannian constellation for the non-coherent communications that does not require channel estimation. Then, we design the transmit and receive ABF via the slow time-varying angle-of-departure (AoD) and angle-of-arrival (AoA) information, respectively. The ABF design targets maximizing the intended signal power while suppressing the strong self-interference (SI) occurred in the FD tra…
In this paper, we investigate an intelligent reflecting surface (IRS) assisted multi-user multiple-input multiple-output (MIMO) full-duplex (FD) system. We jointly optimize the active beamforming matrices at the access point (AP) and uplink users, and the passive beamforming matrix at the IRS to maximize the weighted sum-rate of the system. Since it is practically difficult to acquire the channel state information (CSI) for IRS-related links due to its passive operation and large number of elements, we conceive a mixed-timescale beamforming scheme. Specifically, the high-dimensional passive be…
Modern millimeter wave (mmWave) communication systems rely on beam alignment to deliver sufficient beamforming gain to close the link between devices. We present a novel beam selection methodology for multi-panel, full-duplex mmWave systems, which we call STEER, that delivers high beamforming gain while significantly reducing the full-duplex self-interference coupled between the transmit and receive beams. STEER does not necessitate changes to conventional beam alignment methodologies nor additional over-the-air feedback, making it compatible with existing cellular standards. Instead, STEER us…
We present measurements of the 28 GHz self-interference channel for full-duplex sectorized multi-panel millimeter wave (mmWave) systems, such as integrated access and backhaul. We measure the isolation between the input of a transmitting phased array panel and the output of a co-located receiving phased array panel, each of which is electronically steered across a number of directions in azimuth and elevation. In total, nearly 6.5 million measurements were taken in an anechoic chamber to densely inspect the directional nature of the coupling between 256-element phased arrays. We observe that h…
In this paper, a full-duplex unmanned aerial vehicle (FD-UAV) relay is employed to increase the communication capacity of millimeter-wave (mmWave) networks. Large antenna arrays are equipped at the source node (SN), destination node (DN), and FD-UAV relay to overcome the high path loss of mmWave channels and to help mitigate the self-interference at the FD-UAV relay. Specifically, we formulate a problem for maximization of the achievable rate from the SN to the DN, where the UAV position, analog beamforming, and power control are jointly optimized. Since the problem is highly non-convex and in…
Recently, full duplex (FD) has been studied in 5G LTE millimeter wave (mmWave) cellular communications for New Radio in 3GPP releases 15-17. FD allows bidirectional transmission over the same resources and has the potential to reduce latency and double spectral efficiency. Self-interference (SI) is the primary drawback. SI can be several orders of magnitude greater than the received signal power, saturate the analog-to-digital converters (ADCs) and degrade communication performance severely. Massive mmWave antenna arrays may provide enough degrees of freedom for spatial multiplexing and SI sup…
This paper studies intelligent reflecting surface (IRS)-aided full-duplex (FD) wireless-powered communication network (WPCN), where a hybrid access point (HAP) broadcasts energy signals to multiple devices for their energy harvesting in the downlink (DL) and meanwhile receives information signals in the uplink (UL) with the help of IRS. Particularly, we propose three types of IRS beamforming configurations to strike a balance between the system performance and signaling overhead as well as implementation complexity. We first propose the fully dynamic IRS beamforming, where the IRS phase-shift …
This paper investigates the downlink transmission of reconfigurable intelligent surface (RIS)-aided cooperative non-orthogonal-multiple-access (C-NOMA), where both half-duplex (HD) and full-duplex (FD) relaying modes are considered. The system model consists of one base station (BS), two users and one RIS. The goal is to minimize the total transmit power at both the BS and at the user-cooperating relay for each relaying mode by jointly optimizing the power allocation coefficients at the BS, the transmit power coefficient at the relay user, and the passive beamforming at the RIS, subject to pow…
This letter considers the secure communication in a reconfigurable intelligent surface (RIS) aided full duplex (FD) system. An FD base station (BS) serves an uplink (UL) user and a downlink (DL) user simultaneously over the same time-frequency dimension assisted by a RIS in the presence of an eavesdropper. In addition, the artificial noise (AN) is also applied to interfere the eavesdropper's channel. We aim to maximize the sum secrecy rate of UL and DL users by jointly optimizing the transmit beamforming, receive beamforming and AN covariance matrix at the BS, and passive beamforming at the RI…
Millimeter wave (mmWave) full-duplex (FD) is a promising technique for improving capacity by maximizing the utilization of both time and the rich mmWave frequency resources. Still, it has restrictions due to FD self-interference (SI) and mmWave's limited coverage. Therefore, this study dives into FD mmWave MIMO with the assistance of reconfigurable intelligent surfaces (RIS) for capacity improvement. First, we demonstrate the angular-domain reciprocity of FD antenna arrays under the far-field planar wavefront assumption. Accordingly, a strategy for joint downlink-uplink (DL-UL) channel estimat…
In this work, we present a framework analysis of full-duplex (FD) systems for Millimeter Wave (mmWave) analog architecture. Given that FD systems can double the ergodic capacity, such systems experience large losses caused by the loopback self-interference (SI). In addition, systems with analog architecture also suffer from other forms of losses mainly incurred by the constant amplitude (CA) constraint. For this purpose, we propose the projected Gradient Ascent algorithm to maximize the sum rate under the unit-norm and CA constraints. Unlike previous works, our approach achieves the best spect…
In this letter, we investigate the hybrid beamforming for millimeter wave massive multiple-input multiple-output (MIMO) system based on deep reinforcement learning (DRL). Imperfect channel state information (CSI) is assumed to be available at the base station (BS). To achieve high spectral efficiency with low time consumption, we propose a novel DRL-based method called PrecoderNet to design the digital precoder and analog combiner. The DRL agent takes the digital beamformer and analog combiner of the previous learning iteration as state, and these matrices of current learning iteration as acti…
This paper investigates the passive beamforming and deployment design for an intelligent reflecting surface (IRS) aided full-duplex (FD) wireless system, where an FD access point (AP) communicates with an uplink (UL) user and a downlink (DL) user simultaneously over the same time-frequency dimension with the help of IRS. Under this setup, we consider three deployment cases: 1) two distributed IRSs placed near the UL user and DL user, respectively; 2) one centralized IRS placed near the DL user; 3) one centralized IRS placed near the UL user. In each case, we aim to minimize the weighted sum tr…
Recent applications of the Full Duplex (FD) technology focus on enabling simultaneous control communication and data transmission to reduce the control information exchange overhead, which impacts end-to-end latency and spectral efficiency. In this paper, we present a simultaneous direction estimation and data transmission scheme for millimeter Wave (mmWave) massive Multiple-Input Multiple-Output (MIMO) systems, enabled by a recent FD MIMO technology with reduced hardware complexity Self-Interference (SI) cancellation. We apply the proposed framework in the mmWave analog beam management proble…
Hybrid beamforming (HBF) design is a crucial stage in millimeter wave (mmWave) multi-user multi-input multi-output (MU-MIMO) systems. However, conventional HBF methods are still with high complexity and strongly rely on the quality of channel state information. We propose an extreme learning machine (ELM) framework to jointly optimize transmitting and receiving beamformers. Specifically, to provide accurate labels for training, we first propose an factional-programming and majorization-minimization based HBF method (FP-MM-HBF). Then, an ELM based HBF (ELM-HBF) framework is proposed to increase…
Full Duplex (FD) radio has emerged as a promising solution to increase the data rates by up to a factor of two via simultaneous transmission and reception in the same frequency band. This paper studies a novel hybrid beamforming (HYBF) design to maximize the weighted sum-rate (WSR) in a single-cell millimeter wave (mmWave) massive multiple-input-multiple-output (mMIMO) FD system. Motivated by practical considerations, we assume that the multi-antenna users and hybrid FD base station (BS) suffer from the limited dynamic range (LDR) noise due to non-ideal hardware and an impairment aware HYBF ap…
Integrated Sensing and Communication (ISAC) has attracted substantial attraction in recent years for spectral efficiency improvement, enabling hardware and spectrum sharing for simultaneous sensing and signaling operations. In-band Full Duplex (FD) is being considered as a key enabling technology for ISAC applications due to its simultaneous transmission and reception capability. In this paper, we present an FD-based ISAC system operating at millimeter Wave (mmWave) frequencies, where a massive Multiple-Input Multiple-Output (MIMO) Base Station (BS) node employing hybrid Analog and Digital (A/…
Intelligent reflecting surface (IRS) technology offers more feasible propagation paths for millimeter-wave (mmWave) communication systems to overcome blockage than existing technologies. In this paper, we consider a downlink wireless system with the IRS and formulate a joint power allocation and beamforming design problem to maximize the weighted sum-rate, which is a multi-variable optimization problem. To solve the problem, we propose a novel alternating manifold optimization based beamforming algorithm. Simulation results show that our proposed optimization algorithm outperforms existing alg…
Integrated access and backhaul (IAB) facilitates cost-effective deployment of millimeter wave(mmWave) cellular networks through multihop self-backhauling. Full-duplex (FD) technology, particularly for mmWave systems, is a potential means to overcome latency and throughput challenges faced by IAB networks. We derive practical and tractable throughput and latency constraints using queueing theory and formulate a network utility maximization problem to evaluate both FD-IAB and half-duplex(HD)-IAB networks. We use this to characterize the network-level improvements seen when upgrading from convent…
This work studies the effectiveness of a novel simultaneous transmission and reflection reconfigurable intelligent surface (STAR-RIS) aided Full-Duplex (FD) communication system. We aim to maximize the energy efficiency by jointly optimizing the transmit power and passive beamforming at the STAR-RIS. We propose an efficient algorithm to optimize them iteratively under the alternating optimization framework. The successive convex approximation (SCA) and Dinkelbach's method are used to solve the power optimization subproblem. The penalty-based method is used to design passive beamforming at the …
In this letter, we investigate the millimeter wave (mmWave) downlink multiuser multiple-input multiple-output (MU-MIMO) system, adopting the dynamic subarray architecture at the base station and considering the multi-stream communication for each user. Aiming at maximizing the system spectral efficiency, we propose a novel hybrid beamforming design. First, assuming no inter-user interference (IUI), we easily get the optimal fully-digital beamformers and combiners using the singular value decomposition of each user channel and the waterfilling algorithm. Then, based on the obtained fullydigital…
Wireless communication systems can be enhanced at the link level, in medium access, and at the network level when transceivers are equipped with full-duplex capability: the transformative ability to simultaneously transmit and receive over the same frequency spectrum. Effective methods to cancel self-interference are required to facilitate full-duplex operation, which we overview herein in the context of traditional radios, along with those in next-generation wireless networks. We highlight advances in self-interference cancellation that leverage machine learning, and we summarize key consider…
