Solar arrays are the primary energy source of the satellite. In this paper, a metamaterial absorber for solar arrays with simultaneous high optical transparency and broadband microwave absorption is presented. By tailoring the reflection response of meta-atoms, 85% absorption performance from 6.8GHz to 18GHz is obtained. In the meantime, by employing transparent substrates, including indium tin oxide (ITO) film and anti-reflection glass, a maximum of 87% light transmittance is achieved. The absorptivity of the proposed metamaterial absorber is simulated and measured experimentally. Light transmittance and the effect of transparent metamaterial absorber on the conversion efficiency of the solar array have also been measured. These results fully demonstrate the reliability of our design for solar arrays, which also meet the requirements of structural strength, atomic oxygen erosion resistance, weight limitation, etc.
This paper presents a slot antenna array with a reconfigurable radar cross section (RCS). The antenna system is formed by combining a liquid absorber with a 2*2 slot antenna array. The liquid absorber consists of a polymethyl methacrylate (PMMA) container, a 45% ethanol layer, and a metal ground,which is attached to the surface of the slot antenna array. The incident wave can be absorbed by the absorber rather than reflected in other directions when the PMMA container is filled with ethanol, which reduces the monostatic and bistatic RCS. Thus the RCS of the antenna can be changed by injecting …
Absorbing materials in ultra-high frequency (UHF) band has constantly been a major challenge. The size of the absorber in UHF band is large, whereas the resonant frequency band is narrow. According to Rozanov's theory, two kinds of composite metamaterial absorbers are designed to realize the requirements of low-frequency broadband metamaterial microwave absorber: the magnetic-metamaterial composite absorber1 (MA1) and the dielectric-metamaterial composite absorber 2 (MA2). In the range of approximately 300-1000MHz, both absorbers achieve absorption of over 90% and feature good adaptability to …
We demonstrate a ventilated metamaterial absorber operating at low frequency (< 500 Hz).With only two layers of the absorption units, high-efficiency absorption (> 90%) has been achieved in both simulations and experiments. This high-efficiency absorption under ventilation condition is originated from the weak coupling of the two identical split tube resonators constituting the absorber, which leads to the hybridization of the degenerate eigenmodes and breaks the absorption upper limit of 50% for conventional transmissive symmetric acoustic absorbers. The absorber can also be extended to an ar…
In this paper, a superlattice VO2/SiO2 metamaterial on a lossy substrate is designed to create a near perfect absorber with tunability across the infrared spectrum. We selected VO2 as it presents a dielectric to metal-like phase change slightly above room temperature. Additionally, the slightly lossy nature of high-temperature VO2 presents comparable and small components (real and imaginary) of the complex refractive index across portions of the visible and infrared. Coupled with a limited conductivity substrate, VO2 has been employed to create highly absorbing/emitting structures where the th…
By using a structured tungsten-polyurethane composite that is impedance-matched to water while simultaneously having a much slower longitudinal sound speed, we have theoretically designed, and experimentally realized, an underwater acoustic absorber exhibiting high absorption from 4 to 20 kHz, measured in a 5.6m times 3.6m water pool with the time-domain approach. The broadband functionality is achieved by optimally engineering the distribution of the Fabry-Perot resonances, based on an integration scheme, to attain impedance matching over a broad frequency range. The average thickness of the …
Increasing attention on microwave ultra-broadband metamaterial absorbers has been paid due to their promising applications. While most microwave ultra-broadband metamaterial absorbers developed so far are based on metallic resonant structures, dispersive dielectric water-based metamaterial opens a simpler and more versatile route for the construction of polarization- and angle- insensitive ultra-broadband absorption. Here, we review the recent progresses of water-based metamaterial absorber by providing an illustration of the mechanisms to realize ultra-broadband, tunable and multi-functional …
In this paper, a liquid reconfigurable stealth window constructed by metamaterial absorber at microwave band is proposed. The stealth window consists of an anti-reflection glass with indium tin oxide (ITO) as resistive film and a liquid container made of polymethyl methacrylate (PMMA). Since the materials constituting the window are all transparent, the metamaterials that can be switched through the liquid control system can always maintain high light transmission. The proposal can obtain a transmission passband from 2.3 GHz to 5 GHz with low insertion loss, especially at 2.45 GHz and 5 GHz wi…
This paper proposes a functionally reconfigurable integrated structure of a Fabry-Perot (FP) antenna and wideband liquid absorber. The partial reflecting surface (PRS) is elaborately tailored to serve as both a component of the FP antenna and the metal ground of the broadband liquid absorber. Then the integrated structure is realized by combining the FP antenna with the liquid absorber. The PRS is composed of patches on the top layer of the substrate and the square loop on the bottom and the microstrip patch antenna is used as a source. The liquid absorber is composed of a 3-D printed containe…
Ultrawide-angle electromagnetic wave absorbers with excellent mechanical properties are required in many diverse applications such as sensing, and stealth technologies. Here, a novel 3D reconfigurable metamaterial absorber (MMA) consisting of honeycomb and VO2 films is proposed. The proposed MMA exhibits a strong absorptivity above 90\% in the widest incident angle up to $87^\circ$ for TM- and TE- polarized oblique incidences for THz wave propagating in yoz-plane. According to simulation results, under normal incidence, when VO2 films are in the insulating state, the proposed absorber exhibits…
For most acoustic metamaterials, once they have been fabricated, their operating frequencies and functions cannot be adjusted, which is an intrinsic barrier for development of realistic applications. The study to overcome this limit has become a significant issue in acoustic metamaterial engineering. Although with the advance of metamaterials in the past two decades, a series of methods such as electric or magnetic control have been proposed, most of them can only work in the condition of no fluid passage. Some metamaterials with large transmission losses have been proposed, but the sounds are…
In this paper, a low radar cross section (RCS) patch antenna based on the 3-bit metasurface composed of linear polarization conversion elements is designed. At first, 3-bit coding metamaterials are constructed by a sequence of eight coded unit cells, which have a similar cross-polarized reflected amplitude response and gradient reflected phase responses covering 0~2π, respectively. Equivalent circuit models (ECMs) of these unit cells are created to describe their electrical behavior for the two linear incident polarizations at the same time. Then, a patch antenna is integrated on the 3-bit met…
We propose a thin, compact, broadband, polarization and angle insensitive metamaterial absorber based on a tungsten reflector, silicon spacer and a top pattern composed of a double square-like ring resonator utilizing nickel(Ni). In such a structure, a high absorption (above 80 %) bandwidth ~ 4.8 μm from 3.52 up to 8.32 μm corresponding to the relative bandwidth ~81% can be achieved with deeply subwavelength unit cell dimensions. Here the physical origin of the broadband absorption is associated with low Q-factor dipole modes of the top pattern inner and outer sides functioning as rectangular …
Terahertz (THz) metamaterials have been developed for THz sensing, detection, imaging, and many other functions due to their unusual absorbers. However, the unusual absorption spectra change with different incident angles. Thus, we designed and fabricated a focal plane array with metal-insulator-metal (MIM) structure metamaterial absorbers for further research. The absorption spectrum with incident angles from 20 to 60 was measured using THz time-domain spectroscopy (THz-TDS), and the experimental results reveal that the absorption spectrum changes with incident angle variations. A basic analy…
Metamaterial-based absorbers have been extensively investigated in the terahertz (THz) range with ever increasing performances. In this paper, we propose an all-dielectric THz absorber based on doped silicon. The unit cell consists of a silicon cross resonator with an internal cross-shaped air cavity. Numerical results suggest that the proposed absorber can operate from THz to mid-infrared, having an average power absorption of >95% between 0.6 and 10 THz. Experimental results using THz time-domain spectroscopy show a good agreement with simulations. The underlying mechanisms for broadband abs…
High-efficiency absorption of low-frequency sounds (< 1000 Hz) while maintaining a free flow of fluids remains a significant challenge in acoustical engineering due to the rigid trade-off between absorption and ventilation performances. Although ongoing advances in acoustic metamaterials have unlocked unprecedented possibilities and various metamaterial absorbers have been proposed, most of them only work adequately in the condition of no sound transmissions. Unfortunately, such condition requires a complete block of fluid channels due to longitudinal nature of sounds, which allows them to pen…
The implementation of terahertz (THz) wafer-level metadevices is critical to advance the science for applications including (I) integrated focal plane array which can image for biology and (II) integrated narrowband absorbers for high spectral resolution THz spectroscopy. Substantial progress has been made in the development of THz metamaterials; however, a wafer-level low-stress THz metadevices platform remains a challenge. This paper experimentally demonstrates a substrate-free THz metadevices platform adopting engineered Si-rich and low-stress silicon nitride (SiNx) thin films, achieving an…
This work experimentally studies silicon-cored tungsten nanowire selective metamaterial absorber to enhance solar-thermal energy harvesting, simply fabricated by conformally coating a thin tungsten layer onto a commercial silicon nanowire stamp. Scanning electron microscopy is used to characterize the morphology change before and after the tungsten deposition, while optical spectroscopy is carried out to measure the spectral absorptance (or emittance) in the broad wavelength range from solar spectrum to infrared. It is shown that the tungsten nanowire absorber exhibits almost the same total so…
We propose herein a method of material-structure integrated design for broadband absorption of dielectric metamaterial, which is achieved by combination of genetic algorithm and simulation platform. A multi-layered metamaterial absorber with an ultra-broadband absorption from 5.3 to 18 GHz (a relative bandwidth of as high as 109%) is realized numerically and experimentally. In addition, simulated results demonstrate the proposed metamaterial exhibits good incident angle and polarization tolerance, which also are significant criteria for practical applications. By investigating the working prin…
While the design of always new metamaterials with exotic static and dynamic properties is attracting deep attention in the last decades, little effort is made to explore their interactions with other materials. This prevents the conception of (meta-)structures that can enhance metamaterials' unorthodox behaviours and that can be employed in real engineering applications. In this paper, we give a first answer to this challenging problem by showing that the relaxed micromorphic model with zero static characteristic length can be usefully applied to describe the refractive properties of simple me…
We present a guide for the design and fabrication of a CMOS-compatible metamaterial microstructure as an absorber of visible light with exceptionally high absorption efficiency (~ 98%), for wavelengths 400nm-700nm. The structural parameters of the microstructure have been optimized by using Finite Element method (FEM) based COMSOL multyphysics software simulations. An optimized 2D unit cell of the structure consists of 4um by 160 nm TiN base on glass substrate covered with 70 nm thick silicon dioxide (SiO2). A periodic structure of titanium nitride (TiN) straps (each of 90 nm thick and 2-micro…
Selective solar absorbers (SSAs) with high performance are the key to concentrated solar power systems. Optical metamaterials are emerging as a promising strategy to enhance selective photon absorption, however, the high-temperature resistance (>500C) remains as one of the main challenges for their practical applications. Here, a multilayered metamaterial system (Al2O3/W/SiO2/W) based on metal-insulator-metal (MIM) resonance effect has been demonstrated with high solar absorptance over 92%, low thermal emittance loss below 6%, and significant high-temperature resistance: it has been proved tha…
Conventional multistatic radar systems using microwave and millimeter-wave (mm-wave) frequencies seek to reconstruct the target in the imaging domain, employing many transmitting and receiving antenna elements. These systems are suboptimal, in that they do not take into consideration the large mutual information existing between the measurements. This work reports a new mm-wave radar system for high sensing capacity applications. The system is composed of a Compressive Reflector Antenna (CRA), whose surface is specially tailored by digitized Metamaterial Absorbers (MMAs). The MMA elements are …
Engineered optical absorbers are of substantial interest for applications ranging from stray light reduction to energy conversion. We demonstrate a large-area (centimeter-scale) metamaterial that features near-unity frequency-selective absorption in the mid-infrared wavelength range. The metamaterial comprises a self-assembled porous structure known as an inverse opal, here made of silica. The structure's large volume fraction of voids, together with the vibrational resonances of silica in the mid-infrared spectral range, reduce the metamaterial's refractive index to close to that of air and i…
We theoretically investigate photothermal heating of ultra-flexible metamaterials, which are obtained by randomly mixing TiN nanoparticles in polydimethylsiloxane (PDMS). Due to the plasmonic properties of TiN nanoparticles, incident light is perfectly absorbed in a broadband range (300-3000 nm) to generate heat within these metamaterials. Under irradiation of an 808 nm near-infrared laser with different intensities, our predicted temperature rises as a function of time agree well with recent experimental data. For a given laser intensity, the temperature rise varies non-monotonically with con…
Designing broadband metamaterial perfect absorbers is challenging due to the intrinsically narrow bandwidth of surface plasmon resonances. Here, the paper reports an ultra-broadband metamaterial absorber by using space filling Gosper curve. The optimized result shows an average absorptivity of 95.78% from 2.64 to 9.79 μm across the entire mid-infrared region. Meanwhile, the absorber shows insensitivity to the polarization angle and the incident angle of the incident light. The underlying physical principles, used in our broadband absorber, involve a fractal geometry with multiple scales and a …
Spectrally selective solar absorbers (SSAs), harvesting sunlight into heat, are the key to the concentrated solar thermal systems. Current SSAs' designs using photonic crystals, metamaterials, or cermets are either cost-inefficient or have limited applicability due to complicated nanofabrication methods and poor thermal stability at high temperatures. We present a scalable-manufactured blackbody cavity solar absorber design with nearly ideal properties. The unity solar absorptivity and nearly zero infrared emissivity allow for a stagnation temperature of 880C under 10 suns. The performance sur…
Complete absorption of electromagnetic waves is paramount in today's applications, ranging from photovoltaics to cross-talk prevention into sensitive devices. In this context, we use a genetic algorithm (GA) strategy to optimize absorption properties of periodic arrays of truncated square-based pyramids made of alternating stacks of metal/dielectric layers. We target ultra-broadband quasi-perfect absorption of normally incident electromagnetic radiations in the visible and near-infrared ranges (wavelength comprised between 420 and 1600 nm). We compare the results one can obtain by considering …
A highly-efficient multi-resonant RF energy-harvesting rectenna based on a metamaterial perfect absorber featuring closely-spaced polarization-independent absorption modes is presented. Its effective area is larger than its physical area, and so efficiencies of 230% and 130% are measured at power densities of 10 uW/cm2 and 1 uW/cm2 respectively, for a linear absorption mode at 0.75 GHz. The rectenna exhibits a broad polarization-independent region between 1.4 GHz and 1.7 GHz with maximum efficiencies of 167% and 36% for those same power densities. Additionally, by adjustment of the distance be…
The requirement for metamaterial perfect absorbers (MPA) based on doped semiconductors is steadily increasing due to the available matured fabrication and simulation technology. There is a particular interest in developing terahertz (THz) perfect absorbers using doped semiconductors for achieving characteristics such as polarization-independence, wide-angle, and broadband absorption. We report MPA based on patterned arrays of tapered micro-cylindrical structures of doped silicon to enable them with broadband, wide-angle, and polarization-independent response. In this work, we modeled the MPA s…
Wave absorption in time-invariant, passive thin films is fundamentally limited by a trade-off between bandwidth and overall thickness. In this work, we investigate the use of temporal switching to reduce signal reflections from a thin grounded slab over broader bandwidths. We extend quasi-normal mode theory to time switching, developing an ab initio formalism that can model a broad class of time-switched structures. Our formalism provides optimal switching strategies to maximize the bandwidth over which minimal reflection is achieved, showing promising prospects for time-switched nanophotonic …
Metamaterials have great potential to construct ultrathin, miniaturized, and cost-effective microwave and optical devices for future wireless communication systems. Here, a dual-band meta-absorber comprising four arrows-shaped unit cells is investigated. The absorption features are numerically studied and analyzed in a microwave frequency spectrum from 28 - 36 GHz. The proposed meta-absorber illustrates the two independent absorption peaks of 96% and 99.99% at the corresponding operating points of 31.11 GHz and 33.77 GHz, respectively, within the 5G spectrum. Due to structure symmetry, the pro…
Aligned, densely-packed carbon nanotube metamaterials prepared using vacuum filtration are an emerging infrared nanophotonic material. We report multiple hyperbolic plasmon resonances, together spanning the mid-infrared, in individual resonators made from aligned and densely-packed carbon nanotubes. In the first near-field scanning optical microscopy (NSOM) imaging study of nanotube metamaterial resonators, we observe distinct deeply-subwavelength field profiles at the fundamental and higher-order resonant frequencies. The wafer-scale area of the nanotube metamaterials allows us to combine thi…
The unusual viscoelastic properties of silica aerogel plates are efficiently used to design subwavelength perfect sound absorbers. We theoretically, numerically and experimentally report a perfect absorbing metamaterial panel made of periodically arranged resonant building blocks consisting of a slit loaded by a clamped aerogel plate backed by a closed cavity. The impedance matching condition is analyzed using the Argand diagram of the reflection coefficient, i.e., the trajectory of the reflection coefficient as a function of frequency in the complex plane. The lack or excess of losses in the …
The Brewster's law predicts zero reflection of p-polarization on a dielectric surface at a particular angle. However, when loss is introduced into the permittivity of the dielectric, the Brewster condition breaks down and reflection unavoidably appears. In this work, we found an exception to this long-standing dilemma by creating a class of nonmagnetic anisotropic metamaterials, where an anomalous Brewster effects with independently tunable absorption and refraction emerges. This loss-independent Brewster effect is bestowed by the extra degrees of freedoms introduced by anisotropy and strictly…
Metamaterials and metasurfaces operating in the visible and near-infrared (NIR) offer a promising route towards next-generation photodetectors and devices for solar energy harvesting. While numerous metamaterials and metasurfaces using metals and semiconductors have been demonstrated, semimetals-based metasurfaces in the vis-NIR range are notably missing. Here, we experimentally demonstrate a broadband metasurface superabsorber based on large area, semimetallic, van der Waals PtSe2 thin films in agreement with electromagnetic simulations. Our results show that PtSe2 is an ultrathin and scalabl…
