This paper presents a data-aided channel estimator that reduces the channel estimation error of the conventional linear minimum-mean-squared-error (LMMSE) method for multiple-input multiple-output communication systems. The basic idea is to selectively exploit detected symbol vectors obtained from data detection as additional pilot signals. To optimize the selection of the detected symbol vectors, a Markov decision process (MDP) is defined which finds the best selection to minimize the mean-squared-error (MSE) of the channel estimate. Then a reinforcement learning algorithm is developed to solve this MDP in a computationally efficient manner. Simulation results demonstrate that the presented channel estimator significantly reduces the MSE of the channel estimate and therefore improves the block error rate of the system, compared to the conventional LMMSE method.
This paper investigates the performance of reconfigurable intelligent surface (RIS)-aided massive multiple-input multiple-output (MIMO) systems with direct links, and the phase shifts of the RIS are designed based on the statistical channel state information (CSI). We first derive the closed-form expression of the uplink ergodic data rate. Then, based on the derived expression, we use the genetic algorithm (GA) to solve the sum data rate maximization problem. With low-complexity maximal-ratio combination (MRC) and low-overhead statistical CSI-based scheme, we validate that the RIS can still br…
Reconfigurable intelligent surface (RIS) has recently drawn intensive attention due to its potential of simultaneously realizing high spectral and energy efficiency in a sustainable way. This paper focuses on the design of efficient transmission methods to maximize the uplink sum throughput in a RIS-aided multi-user multi-input multi-output (MU-MIMO) system. To provide an insightful basis, the channel capacity of RIS-aided MU-MIMO is theoretically analyzed. Then, the conventional transmission schemes based on orthogonal multiple access are presented as the baseline. From the information-theore…
We consider a reconfigurable intelligent surface (RIS)-aided massive multi-user multiple-input multiple-output (MIMO) communication system with transceiver hardware impairments (HWIs) and RIS phase noise. Different from the existing contributions, the phase shifts of the RIS are designed based on the long-term angle informations. Firstly, an approximate analytical expression of the uplink achievable rate is derived. Then, we use genetic algorithm (GA) to maximize the sum rate and the minimum date rate. Finally, we show that it is crucial to take HWIs into account when designing the phase shift…
Reconfigurable Intelligent Surfaces (RISs) are one of the key emerging 6th Generation (6G) technologies that are expected to improve the link budgets between transmitters and receivers by adding artificial propagation paths. In such re-configured propagation environment, Downlink (DL) Multi-User Multi-Input Multi-Output (MU-MIMO) brings capacity improvement to cellular networks. It benefits from the spatial dimension offered by MIMO systems to enable simultaneous transmission of independent data streams to multiple users on the same radio resources by applying appropriate Beamforming (BF) sche…
Millimeter-wave (mmWave) channels, which occupy frequency ranges much higher than those being used in previous wireless communications systems, are utilized to meet the increased throughput requirements that come with 5G communications. The high levels of attenuation experienced by electromagnetic waves in these frequencies causes MIMO channels to have high spatial correlation. To attain desirable error performances, systems require knowledge about the channel correlations. In this thesis, a deep neural network aided method is proposed for the parametric estimation of the channel covariance ma…
Index modulation (IM) brings the reduction of power consumption and complexity of the transmitter to classical multiple-input multiple-output orthogonal frequency division multiplexing (MIMO-OFDM) systems. However, due to the introduction of IM, the complexity of the detector at receiver is greatly increased. Furthermore, the detector also requires the channel state information at receiver, which leads to high system overhead. To tackle these challenges, in this paper, we introduce deep learning (DL) in designing a non-iterative detector. Specifically, based on the structural sparsity of the t…
Massive MIMO wireless FDD systems are often confronted by the challenge to efficiently obtain downlink channel state information (CSI). Previous works have demonstrated the potential in CSI encoding and recovery by take advantage of uplink/downlink reciprocity between their CSI magnitudes. However, such a framework separately encodes CSI phase and magnitude. To improve CSI encoding, we propose a learning-based framework based on limited CSI feedback and magnitude-aided information. Moving beyond previous works, our proposed framework with a modified loss function enables end-to-end learning to…
Cell-free systems can effectively eliminate the inter-cell interference by enabling multiple base stations (BSs) to cooperatively serve users without cell boundaries at the expense of high costs of hardware and power sources due to the large-scale deployment of BSs. To tackle this issue, the low-cost reconfigurable intelligent surface (RIS) can serve as a promising technique to improve the energy efficiency of cell-free systems. In this paper, we consider an RIS aided cell-free MIMO system where multiple RISs are deployed around BSs and users to create favorable propagation conditions via reco…
This letter investigates the reconfigurable intelligent surface (RIS)-aided massive multiple-input multiple-output (MIMO) systems with a two-timescale design. First, the zero-forcing (ZF) detector is applied at the base station (BS) based on instantaneous aggregated CSI, which is the superposition of the direct channel and the cascaded user-RIS-BS channel. Then, by leveraging the channel statistical property, we derive the closed-form ergodic achievable rate expression. Using a gradient ascent method, we design the RIS passive beamforming only relying on the long-term statistical CSI. We prove…
A reconfigurable intelligent surface (RIS) can shape the radio propagation by passively changing the directions of impinging electromagnetic waves. The optimal control of the RIS requires perfect channel state information (CSI) of all the links connecting the base station (BS) and the mobile station (MS) via the RIS. Thereby the channel (parameter) estimation at the BS/MS and the related message feedback mechanism are needed. In this paper, we adopt a two-stage channel estimation scheme for the RIS-aided millimeter wave (mmWave) MIMO channels using an iterative reweighted method to sequentiall…
Index modulation (IM) reduces the power consumption and hardware cost of the multiple-input multiple-output (MIMO) system by activating part of the antennas for data transmission. However, IM significantly increases the complexity of the receiver and needs accurate channel estimation to guarantee its performance. To tackle these challenges, in this paper, we design a deep learning (DL) based detector for the IM aided MIMO (IM-MIMO) systems. We first formulate the detection process as a sparse reconstruction problem by utilizing the inherent attributes of IM. Then, based on greedy strategy, we …
Multiuser massive multiple-input multiple-output (MU-MIMO) systems can be used to meet high throughput requirements of 5G and beyond networks. In an uplink MUMIMO system, a base station is serving a large number of users, leading to a strong multi-user interference (MUI). Designing a high performance detector in the presence of a strong MUI is a challenging problem. This work proposes a novel detector based on the concepts of expectation propagation (EP) and graph neural network, referred to as the GEPNet detector, addressing the limitation of the independent Gaussian approximation in EP. The …
Location information offered by external positioning systems, e.g., satellite navigation, can be used as prior information in the process of beam alignment and channel parameter estimation for reconfigurable intelligent surface (RIS)-aided millimeter wave (mmWave) multiple-input multiple-output networks. Benefiting from the availability of such prior information, albeit imperfect, the beam alignment and channel parameter estimation processes can be significantly accelerated with less candidate beams explored at all the terminals. We propose a practical channel parameter estimation method via a…
Reducing computational complexity is crucial in optimizing the phase shifts of Intelligent Reflecting Surface (IRS) systems since IRS-assisted communication systems are generally deployed with a large number of reflecting elements (REs). This letter proposes a low-complexity algorithm, designated as Dimension-wise Sinusoidal Maximization (DSM), to obtain the optimal IRS phase shifts that maximize the sum capacity of a MIMO network. The algorithm exploits the fact that the objective function for the optimization problem is sinusoidal w.r.t. the phase shift of each RE. The numerical results show…
This work studies the modelling and the optimization of intelligent reflecting surface (IRS) assisted multiple-input multiple-output (MIMO) systems through cascaded line-of-sight (LoS) links. In Part I of this work, we build up a new IRS-aided MIMO channel model, named the cascaded LoS MIMO channel. The proposed channel model consists of a transmitter (Tx) and a receiver (Rx) both equipped with uniform linear arrays, and an IRS is used to enable communications between the transmitter and the receiver through the LoS links seen by the IRS. When modeling the reflection of electromagnetic waves a…
As communication systems that employ millimeter wave (mmWave) frequency bands must use large antenna arrays to overcome the severe propagation loss of mmWave signals, hybrid beamforming has been considered as an integral component of mmWave communications. Recently, intelligent reflecting surface (IRS) has been proposed as an innovative technology that can significantly improve the performance of mmWave communication systems through the use of low-cost passive reflecting elements. In this paper, we study IRS-aided mmWave multiple-input multiple-output (MIMO) systems with hybrid beamforming arc…
Intelligent reflecting surface (IRS) is a promising solution to enhance the wireless communication capacity both cost-effectively and energy-efficiently, by properly altering the signal propagation via tuning a large number of passive reflecting units. In this paper, we aim to characterize the fundamental capacity limit of IRS-aided point-to-point multiple-input multiple-output (MIMO) communication systems with multi-antenna transmitter and receiver in general, by jointly optimizing the IRS reflection coefficients and the MIMO transmit covariance matrix. First, we consider narrowband transmiss…
Orthogonal time frequency space (OTFS) modulation has the potential to enable robust communications in highly-mobile scenarios. Estimating the channels for OTFS systems, however, is associated with high pilot signaling overhead that scales with the maximum delay and Doppler spreads. This becomes particularly challenging for massive MIMO systems where the overhead also scales with the number of antennas. An important observation however is that the delay, Doppler, and angle of departure/arrival information are directly related to the distance, velocity, and direction information of the mobile u…
In this paper, we study surface-based communication systems based on different levels of channel state information for system optimization. We analyze the system performance in terms of rate and degrees of freedom (DoF). We show that the deployment of a reconfigurable intelligent surface (RIS) results in increasing the number of DoF, by extending the near-field region. Over Rician fading channels, we show that an RIS can be efficiently optimized only based on the positions of the transmitting and receiving surfaces, while providing good performance if the Rician fading factor is not too small.
Reconfigurable Intelligent Surface (RIS) is one of the key technologies for the upcoming 6th Generation (6G) communications, which can improve the signal strength at the receivers by adding artificial propagation paths. In the context of Downlink (DL) Multi-User Multiple-Input Multiple-Output (MU-MIMO) communications, designing an appropriate Beamforming (BF) scheme to take full advantage of this reconfigured propagation environment and improve the network capacity is a major challenge. Due to the spatial dimension provided by MIMO systems, independent data streams can be transmitted to multip…
Reconfigurable intelligent surface (RIS) has been recognized as a potential technology for 5G beyond and attracted tremendous research attention. However, channel estimation in RIS-aided system is still a critical challenge due to the excessive amount of parameters in cascaded channel. The existing compressive sensing (CS)-based RIS estimation schemes only adopt incomplete sparsity, which induces redundant pilot consumption. In this paper, we exploit the specific triple-structured sparsity of the cascaded channel, i.e., the common column sparsity, structured row sparsity after offset compensat…
Millimeter wave (mmWave) massive multiple-input multiple-output (massive MIMO) is one of the most promising technologies for the fifth generation and beyond wireless communication system. However, a large number of antennas incur high power consumption and hardware costs, and high-frequency communications place a heavy burden on the analog-to-digital converters (ADCs) at the base station (BS). Furthermore, it is too costly to equipping each antenna with a high-precision ADC in a large antenna array system. It is promising to adopt low-resolution ADCs to address this problem. In this paper, we …
This paper considers an antenna structure where a (non-large) array of radiating elements is placed at short distance in front of a reconfigurable intelligent surface (RIS). We propose a channel estimation procedure using different configurations of the RIS elements and derive a closed-form expression for an achievable downlink spectral efficiency by using the popular hardening lower-bound. Next, we formulate an optimization problem, with respect to the phase shifts of the RIS, aimed at minimizing the channels cross-correlations while preserving the channels individual norms. The numerical ana…
We investigate a reconfigurable intelligent surface (RIS)-aided multi-user massive multiple-input multi-output (MIMO) system where low-resolution digital-analog converters (DACs) are configured at the base station (BS) in order to reduce the cost and power consumption. An approximate analytical expression for the downlink achievable rate is derived based on maximum ratio transmission (MRT) and additive quantization noise model (AQNM), and the rate maximization problem is solved by particle swarm optimization (PSO) method under both continuous phase shifts (CPSs) and discrete phase shifts (DPSs…
Reconfigurable intelligent surface (RIS) is very promising for wireless networks to achieve high energy efficiency, extended coverage, improved capacity, massive connectivity, etc. To unleash the full potentials of RIS-aided communications, acquiring accurate channel state information is crucial, which however is very challenging. For RIS-aided multiple-input and multiple-output (MIMO) communications, the existing channel estimation methods have computational complexity growing rapidly with the number of RIS units $N$ (e.g., in the order of $N^2$ or $N^3$) and/or have special requirements on t…
Cell-free (CF) massive multiple-input multiple-output (MIMO) is a promising solution to provide uniform good performance for unmanned aerial vehicle (UAV) communications. In this paper, we propose the UAV communication with wireless power transfer (WPT) aided CF massive MIMO systems, where the harvested energy (HE) from the downlink WPT is used to support both uplink data and pilot transmission. We derive novel closed-form downlink HE and uplink spectral efficiency (SE) expressions that take hardware impairments of UAV into account. UAV communications with current small cell (SC) and cellular …
Reconfigurable intelligent surfaces (RISs) have emerged as a promising technique to enhance the system spectral efficiency. This paper investigates the ergodic channel capacity (ECC) of an RIS-aided multiple-input multiple-output channel under the assumption that the transmitter-RIS, RIS-receiver, and transmitter-receiver channels contain deterministic line-of-sight paths. Novel expressions are derived to characterize the upper and lower bounds of the ECC. To unveil more system insights, asymptotic analyses are performed to the system ECC in the limit of large signal-to-noise ratio (SNR) and n…
Channel estimation is one of the key issues in practical massive multiple-input multiple-output (MIMO) systems. Compared with conventional estimation algorithms, deep learning (DL) based ones have exhibited great potential in terms of performance and complexity. In this paper, an attention mechanism, exploiting the channel distribution characteristics, is proposed to improve the estimation accuracy of highly separable channels with narrow angular spread by realizing the "divide-and-conquer" policy. Specifically, we introduce a novel attention-aided DL channel estimation framework for conventio…
In this work, the uplink channel estimation problem is considered for a millimeter wave (mmWave) multi-input multi-output (MIMO) system. It is well known that pilot overhead and computation complexity in estimating the channel increases with the number of antennas and the bandwidth. To overcome this, the proposed approach allows the channel estimation at the base station to be aided by the sensing information. The sensing information contains an estimate of scatterers locations in an environment. A simultaneous weighting orthogonal matching pursuit (SWOMP) - sparse Bayesian learning (SBL) algo…
This paper proposes a reconfigurable intelligent surface (RIS)-aided and angular-based hybrid beamforming (AB-HBF) technique for the millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems. The proposed RIS-AB-HBF architecture consists of three stages: (i) RF beamformer, (ii) baseband (BB) precoder/combiner, and (iii) RIS phase shift design. First, in order to reduce the number of RF chains and the channel estimation overhead, RF beamformers are designed based on the 3D geometry-based mmWave channel model using slow time-varying angular parameters of the channel. Second,…
This article aims to reduce huge pilot overhead when estimating the reconfigurable intelligent surface (RIS) relayed wireless channel. Motivated by the compelling grasp of deep learning in tackling nonlinear mapping problems, the proposed approach only activates a part of RIS elements and utilizes the corresponding cascaded channel estimate to predict another part. Through a synthetic deep neural network (DNN), the direct channel and active cascaded channel are first estimated sequentially, followed by the channel prediction for the inactive RIS elements. A three-stage training strategy is dev…
This paper considers the power-efficient resource allocation problem in a cloud radio access network (C-RAN). The C-RAN architecture consists of a set of base-band units (BBUs) which are connected to a set of radio remote heads (RRHs) equipped with massive multiple input multiple output (MIMO), via fronthaul links with limited capacity. We formulate the power-efficient optimization problem in C-RANs as a joint resource allocation problem in order to jointly allocate the RRH and transmit power to each user, and fronthaul links and BBUs assign to active RRHs while satisfying the minimum required…
In the context of cell-free massive multi-input multi-output (CFmMIMO), zero-forcing precoding (ZFP) is superior in terms of spectral efficiency. However, it suffers from channel aging owing to fronthaul and processing delays. In this paper, we propose a robust scheme coined delay-tolerant zero-forcing precoding (DT-ZFP), which exploits deep learning-aided channel prediction to alleviate the effect of outdated channel state information (CSI). A predictor consisting of a bank of user-specific predictive modules is specifically designed for such a multi-user scenario. Leveraging the degree of fr…
Research Center for Information Technology Innovation, Academia Sinica（中央研究院资讯科技创新研究中心）
This paper proposes a novel multiple-input multiple-output (MIMO) symbol detector that incorporates a deep reinforcement learning (DRL) agent into the Monte Carlo tree search (MCTS) detection algorithm. We first describe how the MCTS algorithm, used in many decision-making problems, is applied to the MIMO detection problem. Then, we introduce a self-designed deep reinforcement learning agent, consisting of a policy value network and a state value network, which is trained to detect MIMO symbols. The outputs of the trained networks are adopted into a modified MCTS detection algorithm to provide…
Tsinghua University（清华大学）；Beijing National Research Center for Information Science and Technology（北京信息科学与技术国家研究中心）
Hybrid beamforming is widely recognized as an important technique for millimeter wave (mmWave) multiple input multiple output (MIMO) systems. Generalized spatial modulation (GSM) is further introduced to improve the spectrum efficiency. However, most of the existing works on beamforming assume the perfect channel state information (CSI), which is unrealistic in practical systems. In this paper, joint optimization of downlink pilot training, channel estimation, CSI feedback, and hybrid beamforming is considered in GSM aided frequency division duplexing (FDD) mmWave MIMO systems. With the help o…
