The encapsulation of two-dimensional layered materials such as black phosphorus is of paramount importance for their stability in air. However, the encapsulation poses several questions, namely, how it affects, via the weak van der Waals forces, the properties of the black phosphorus and whether these properties can be tuned on demand. Prompted by these questions, we have investigated the impact of hexagonal boron nitride encapsulation on the structural and vibrational properties of few layer black phosphorus, using a first-principles method in the framework of density functional theory. We demonstrate that the encapsulation with hexagonal boron nitride imposes biaxial strain on the black phosphorus material, flattening its puckered structure, by decreasing the thickness of the layers via the increase of the puckered angle and the intra-layer P-P bonds. This work exemplifies the evolution of structural parameters in layered materials after the encapsulation process. We find that after encapsulation, phosphorene (single layer black phosphorous) contracts by 1.1% in the armchair direction and stretches by 1.3% in the zigzag direction, whereas few layer black phosphorus mainly expands by up to 3% in the armchair direction. However, these relatively small strains induced by the hexagonal BN, lead to significant changes in the vibrational properties of black phosphorus, with the redshifts of up to 10 cm$^{-1}$ of the high frequency optical mode $A_g^1$. In general, structural changes induced by the encapsulation process open the door to substrate controlled strain engineering in two-dimensional crystals.
Graphene nanoribbons are prepared inside boron nitride nanotubes by liquid phase encapsulation and subsequent annealing of 1,2,4-trichlorobenzene. The product is imaged with high resolution transmission electron microscopy, and characterized by optical absorption and Raman spectroscopy. Carbon-containing material is detected inside the boron nitride nanotubes with energy-dispersive x-ray spectroscopy (EDS) and scanning transmission electron microscopy (STEM). The observed structures twist under the electron beam and the characteristic features of nanoribbons appear in the Raman spectra.
The hexagonal boron nitride (hBN) encapsulation has been widely used in the electronics applications of 2D materials to improve device performance by protecting 2D materials against contamination and degradation. It is often assumed that hBN layers as a dielectric would not affect the electronic structure of encapsulated 2D materials. Here we studied few-layer MoS$_2$ encapsulated in hBN flakes by using a combination of theoretical and experimental Raman spectroscopy. We found that after the encapsulation the out-of-plane A$_{1g}$ mode is upshifted, while the in-plane E$_{2g}^1$ mode is downsh…
Metal halide perovskites are known to suffer from rapid degradation, limiting their direct applicability. Here, the degradation of phenethylammonium lead iodide (PEA2PbI4) two-dimensional perovskites under ambient conditions is studied using fluorescence, absorbance and fluorescence lifetime measurements. It is demonstrated that a long-term stability of two-dimensional perovskites can be achieved through the encapsulation with hexagonal boron nitride. While un-encapsulated perovskite flakes degrade within hours, the encapsulated perovskites are stable for at least three months. In addition, en…
We study the mechanical and electronic properties of heterobilayers composed of black phosphorus (BP) on hexagonal boron nitride (hBN) and of blue phosphorus (\Pblue) on hBN by means of ab-intio density functional theory. Emphasis is put on how the stress applied on the constituent layers impact their structural and electronic properties. For this purpose, we adopt a specific scheme of structural relaxation which allows us to distinguish between the energy cost of distorting each layer and the gain in stacking them together. In most cases we find that the BP tends to contract along the softer …
Elemental phosphorous is believed to have several stable allotropes that are energetically nearly degenerate, but chemically reactive. To prevent chemical degradation under ambient conditions, these structures may be capped by monolayers of hexagonal boron nitride ({\em h}-BN) or graphene. We perform {\em ab initio} density functional calculations to simulate scanning tunneling microscopy (STM) images of different layered allotropes of phosphorus and study the effect of capping layers on these images. We find that protective monolayers of insulating {\em h}-BN allow to distinguish between the …
Ab initio calculations within the density-functional theory formalism are performed to investigate the chemical functionalization of a graphene-like monolayer of silicon - silicene - with B, N, Al or P atoms. The structural, electronic, magnetic and vibrational properties are reported. The most preferable adsorption sites are found to be valley, bridge, valley and hill site for B, N, Al and P adatoms, respectively. All the relaxed systems with adsorbed/substituted atoms exhibit metallic behaviour with strongly bonded B, N, Al, and P atoms accompanied by an appreciable electron transfer from si…
Two-dimensional (2D) transition metal dichalcogenides (TMDCs) are the subject of intense investigation for applications in optics, electronics, catalysis, and energy storage. Their optical and electronic properties can be significantly enhanced when encapsulated in an environment that is free of charge disorder. Because hexagonal boron nitride (h-BN) is atomically thin, highly-crystalline, and is a strong insulator, it is one of the most commonly used 2D materials to encapsulate and passivate TMDCs. In this report, we examine how ultrathin h-BN shields an underlying MoS2 TMDC layer from the en…
We study the effect of boron (B) and Phosphorous (P) co-doping on electronic and optical properties of graphitic carbon nitride (g-C$_3$N$_4$ or GCN) monolayer using density functional simulations. The energy band structure indicates that the incorporation of B and P into a hexagonal lattice of GCN reduces the energy band gap from $3.1$ for pristine GCN to $1.9$ eV, thus extending light absorption toward the visible region. Moreover, on the basis of calculating absorption spectra and dielectric function, the co-doped system exhibits an improved absorption intensity in the visible region and mo…
Anisotropic thermo-mechanical response of layered hexagonal boron nitride and black phosphorus: application as a simultaneous pressure and temperature sensor
In amorphous materials, acceptor and donor impurities rarely dope the system (shift the Fermi level). We find out why in a-Si:H. We report simulations on B and P doping of a-Si:H and a-Si. We analyze the Electronic Density of States (EDOS) with concentrations ranging from 1.6% to 12.5% of B or P in a-Si. The results indicate that tetrahedral B and P are effective doping configurations in a-Si, but high impurity concentrations introduce defect states. Clustered B or P also introduced mid-gap states. For a-Si:H, we report that both B(3,1) and P(3,1) (B or P atom bonded with three Si atoms and on…
We show that the optical and electronic properties of nanocrystalline silicon can be efficiently tuned using impurity doping. In particular, we give evidence, by means of ab-initio calculations, that by properly controlling the doping with either one or two atomic species, a significant modification of both the absorption and the emission of light can be achieved. We have considered impurities, either boron or phosphorous (doping) or both (codoping), located at different substitutional sites of silicon nanocrystals with size ranging from 1.1 nm to 1.8 nm in diameter. We have found that the cod…
Thin layers of black phosphorus present an ideal combination of a 2D material with a tunable direct bandgap and high carrier mobility. However the material suffers from degradation in ambient conditions due to an oxidation reaction which involves water, oxygen and light. We have measured the spatial profile of the conductivity on flakes of black phosphorus as a function of time using scanning microwave impedance microscopy. A microwave excitation (3 GHz) allows to image a conducting sample even when covered with a dielectric layer. We observe that on bare black phosphorus, the conductivity cha…
A review of electronic properties of insulating-, boron- and phosphorus-doped diamond is given. The main goal is, to show data in a wider context, to reveal trends and limitations with respect to carrier mobilities, conductivities, p- and n-type doping. Undoped diamond is an insulator with conductivities significantly smaller than 10^-17 Ohmcm at room temperature. Mostly, these insulating films show conductivity activation energies of 1.7 eV, an indication that small amounts of substitutional nitrogen dominates the Fermi-level. The electron and hole mobilities are very high (> 20.000 cm2/Vs at…
Near-field spectroscopy has been extensively applied recently to analyze collective optical properties of materials at the nanoscale. However, vibrations of small molecules were only recognizable in close proximity to a metallic resonator. We show that encapsulation in boron nitride nanotubes (BNNT) enhances the near-field vibrational spectra of C$_{60}$ fullerene, reaching a sensitivity limit of a few hundred molecules. Furthermore, products of chemical reactions inside the tubes can be identified, so long as their vibrational signatures lie in the polariton gap of the BNNT.
Two-dimensional (2D) materials, such as graphene and transition metal dichalcogenides have attracted great attention because of the rich physics and potential applications in next-generation nano-sized electronic devices. Recently, atomically thin black phosphorus (BP) has become a new member of the 2D materials family with high theoretical mobility and tunable bandgap structure. However, degradation of properties under atmospheric conditions and high-density charge traps in BP have largely limited its mobility (~400 cm2/Vs at room temperature) and thus restricted its future applications. Here…
Two-dimensional (2D) layered materials with diverse properties have attracted significant interest in the past decade. The layered materials discovered so far have covered a wide, yet discontinuous electromagnetic spectral range from semimetallic graphene, insulating boron nitride, to semiconductors with bandgaps from middle infrared to visible light. Here, we introduce new layered semiconductors, black arsenic-phosphorus (b-AsP), with highly tunable chemical compositions and electronic and optical properties. Transport and infrared absorption studies demonstrate the semiconducting nature of b…
Few layer phosphorene(FLP) devices are extensively studied due to its unique electronic properties and potential applications on nano-electronics . Here we present magnetotransport studies which reveal electron-electron interactions as the dominant scattering mechanism in hexagonal boron nitride-encapsulated FLP devices. From weak localization measurements, we estimate the electron dephasing length to be 30 to 100 nm at low temperatures, which exhibits a strong dependence on carrier density n and a power-law dependence on temperature (~T-0.4). These results establish that the dominant scatteri…
Black phosphorus (BP) has attracted significant interest as a monolayer or few-layer material with extraordinary electrical and optoelectronic properties. However, degradation in air and other environments is an unresolved issue that may limit future applications. In particular the role of different ambient species has remained controversial. Here, we report systematic experiments combined with ab-initio calculations that address the effects of oxygen and water in the degradation of BP. Our results show that BP rapidly degrades whenever oxygen is present, but is unaffected by deaerated (i.e., …
We have studied electrical transport as a function of carrier density, temperature and bias in multi-terminal devices consisting of hexagonal boron nitride (h-BN) encapsulated titanium trisulfide (TiS$_3$) sheets. Through the encapsulation with h-BN, we observe metallic behavior and high electron mobilities. Below $\sim$60 K an increase in the resistance, and non-linear transport with plateau-like features in the differential resistance are present, in line with the expected charge density wave (CDW) formation. Importantly, the critical temperature and the threshold field of the CDW phase can …
The production of high-quality hexagonal boron nitride (h-BN) is essential for the ultimate performance of two-dimensional (2D) materials-based devices, since it is the key 2D encapsulation material. Here, a decisive guideline is reported for fabricating high-quality h-BN on transition metals: It is crucial to exclude carbon from h-BN related process. Otherwise carbon prevails over boron and nitrogen due to its larger binding energy, thereupon forming graphene on metals after high-temperature annealing. We demonstrate the surface reaction-assisted conversion from h-BN to graphene with high-tem…
Two-dimensional electron gases (2DEG) have been an important source of experimental discovery and conceptual development in condensed matter physics for decades. When combined with the unique electronic properties of two-dimensional (2D) crystals, rich new physical phenomena can be probed at the quantum level. Here, we create a new 2DEG in black phosphorus, a recent member of the two-dimensional atomic crystal family, using a gate electric field. We achieve high carrier mobility in black phosphorus 2DEG by placing it on a hexagonal boron nitride substrate (h-BN). This allows us, for the first …
By using first-principles calculations, we investigated the effects of graphene/boron nitride (BN) encapsulation, surface functionalization by metallic elements (K, Al, Mg and typical transition metals) and molecules (tetracyanoquinodimethane (TCNQ) and tetracyanoethylene (TCNE)) on the electronic properties of layered indium selenide (InSe). It was found that an opposite trend of charge transfer is possible for graphene (donor) and BN (acceptor), which is dramatically different from phosphorene where both graphene and BN play the same role (donor). For InSe/BN heterostructure, a change of the…
Ultrathin black phosphorus, or phosphorene, is the second known elementary two-dimensional material that can be exfoliated from a bulk van der Waals crystal. Unlike graphene it is a semiconductor with a sizeable band gap and its excellent electronic properties make it attractive for applications in transistor, logic, and optoelectronic devices. However, it is also the first widely investigated two dimensional electronic material to undergo degradation upon exposure to ambient air. Therefore a passivation method is required to study the intrinsic material properties, understand how oxidation af…
The preferred location of boron and phosphorus in oxidized free-standing Si nanoparticles was investigated using a first-principles density functional approach. The calculated formation energies indicate that P should segregate to the silicon core, whereas B is equally stable in the Si and SiO_2 regions. Our models thus suggest that, in contrast with nanocrystals with H-terminated surfaces, the efficiency of phosphorus incorporation in oxidized Si nanoparticles can be improved by thermal annealing.
Devices made from graphene encapsulated in hexagonal boron-nitride exhibit pronounced negative bend resistance and an anomalous Hall effect, which are a direct consequence of room-temperature ballistic transport on a micrometer scale for a wide range of carrier concentrations. The encapsulation makes graphene practically insusceptible to the ambient atmosphere and, simultaneously, allows the use of boron nitride as an ultrathin top gate dielectric.
Layered and two-dimensional (2D) materials such as graphene, boron nitride, transition metal dichalcogenides(TMDCs), and black phosphorus (BP) have intriguing fundamental physical properties and bear promise of numerous important applications in electronics and optics. Of them, BP is a novel 2D material that has been theoretically predicted to acquire plasmonic behavior for frequencies below ~0.4 eV when highly doped. The electronic properties of BP are unique due to an anisotropic structure, which could strongly influence collective electronic excitations. Advantages of BP as a material for n…
Two-dimensional materials, such as graphene, boron nitride and transition metal dichalcogenides, have attracted increased interest due to their potential applications in electronics and optoelectronics. Thermal transport in two-dimensional materials could be quite different from three-dimensional bulk materials. This article reviews the progress on experimental measurements and theoretical modeling of phonon transport and thermal conductivity in two-dimensional materials. We focus our review on a few typical two-dimensional materials, including graphene, boron nitride, silicene, transition met…
Based on variable components global optimization algorithm, we predict a stable two-dimensional (2D) phase of boron phosphide with 1:5 stoichiometry, i.e. boron pentaphosphide (BP_5) monolayer, which has a lower formation energy than that of the commonly believed graphitic phase (g-BP). BP_5 monolayer is a multiferroic material with coupled ferroelasticity and ferroelectricity. The predicted reversible strain is up to 41.41%, which is the largest among all reported ferroelastic materials. Due to the non-centrosymmetric structure and electronegativity differences between boron and phosphorus at…
We design a hybrid graphene/hexagonal boron nitride superlattice monolayer and investigate its thermoelectric properties using density functional theory and Boltzmann transport equations with the relaxation time accurately treated by electron-phonon coupling calculations. Compared with that of pristine graphene, the lattice thermal conductivity of the superlattice structure is more than two orders of magnitude lower due to the enhanced three-phonon scattering process originated from the mixed-bond characteristics. Besides, the coexistence of light and heavy bands around the Fermi level leads t…
Atomically thin monolayers of graphene show excellent electronic properties which have led to a great deal of research on their use in nanoscale devices. However, heat management of such nanoscale devices is essential in order to improve their performance. Graphene supported on hexagonal boron nitride (h-BN) substrate has been reported to show enhanced (opto)electronic and thermal properties as compared to extensively used SiO2/Si supported graphene. Motivated by this, we have performed temperature- and power-dependent Raman Spectroscopic measurements on four different types of (hetero)structu…
The current research in graphene spintronics strives for achieving a long spin lifetime, and efficient spin injection and detection in graphene. In this article, we review how hexagonal boron nitride (hBN) has evolved as a crucial substrate, as an encapsulation layer, and as a tunnel barrier for manipulation and control of spin lifetimes and spin injection/detection polarizations in graphene spin valve devices. First, we give an overview of the challenges due to conventional SiO$_2$ substrate for spin transport in graphene followed by the progress made in hBN based graphene heterostructures. T…
The photovoltaic effect is one of the fundamental light-matter interactions in light energy harvesting. In conventional photovoltaic solar cells, the photogenerated charge carriers are extracted by the built-in electric field of a PN junction, typically defined by ionic dopants in a semiconductor. In atomically thin semiconductors, the doping level can be controlled by the field-effect without need of implanting dopants in the lattice, which makes 2D semiconductors prospective materials to implement electrically tunable PN junctions. However, most 2D semiconducting materials do not show ambipo…
We report the fabrication, characterization, and modeling of photoconductive antennas using 40 nm thin-film flakes of black phosphorus (BP) as the photoconductor and hexagonal boron nitride (hBN) as a capping layer to prevent oxidation of BP. Dipole antennas were fabricated on oxidized high-resistivity Si substrates, and BP and hBN flakes were picked up and transferred onto the antenna inside a nitrogen glovebox. The transfer matrix technique was used to optimize the thickness of BP and hBN for maximum absorption. BP flakes were aligned with the armchair axis along the anode-cathode gap of the…
Holey graphyne (HGY) is a recently synthesized two-dimensional semiconducting allotrope of carbon composed of a regular pattern of six and eight-vertex carbon rings. In this study, based on first-principles density functional theory and molecular dynamics simulations, we predict a similar stable porous boron nitride holey graphyne-like structure that we call BN-holey-graphyne (BN-HGY). The dynamical and thermal stability of the structure at room temperature is confirmed by performing calculations of the phonon dispersion relations, and also ab-initio molecular dynamics simulations. BN-HGY stru…
Tellurium can form nanowires of helical atomic chains. Given their unique one-dimensional van der Waals structure, these nanowires are expected to show remarkably different physical and electronic properties than bulk tellurium. Here we show that few-chain and single-chain van der Waals tellurium nanowires can be isolated using carbon nanotube and boron nitride nanotube encapsulation. With the approach, the number of atomic chains can be controlled by the inner diameter of the nanotube. The Raman response of the structures suggests that the interaction between a single-atomic tellurium chain a…
The remarkable properties of graphene stem from its two-dimensional (2D) structure, with a linear dispersion of the electronic states at the corners of the Brillouin zone (BZ) forming a Dirac cone. Since then, other 2D materials have been suggested based on boron, silicon, germanium, phosphorus, tin, and metal di-chalcogenides. Here, we present an experimental investigation of a single silicon layer on Au(111) using low energy electron diffraction (LEED), high resolution angle-resolved photoemission spectroscopy (HR-ARPES), and scanning tunneling microscopy (STM). The HR-ARPES data show compel…
Two-dimensional (2D) insulators are a key element in the design and fabrication of van der Waals heterostructures. They are vital as transparent dielectric spacers whose thickness can influence both the photonic, electronic, and optoelectronic properties of 2D devices. Simultaneously, they provide protection of the active layers in the heterostructure. For these critical roles, hexagonal Boron Nitride (hBN) is the dominant choice due to its large bandgap, atomic flatness, low defect density, and encapsulation properties. However, the broad catalogue of 2D insulators offers exciting opportuniti…
Low-symmetry 2D materials---such as ReS$_2$ and ReSe$_2$ monolayers, black phosphorus monolayers, group-IV monochalcogenide monolayers, borophene, among others---have more complex atomistic structures than the honeycomb lattices of graphene, hexagonal boron nitride, and transition metal dichalcogenides. The reduced symmetries of these emerging materials give rise to inhomogeneous electron, optical, valley, and spin responses, as well as entirely new properties such as ferroelasticity, ferroelectricity, magnetism, spin-wave phenomena, large nonlinear optical properties, photogalvanic effects, a…
Atomically thin transition metal dichalcogenide crystals (TMDCs) have extraordinary optical properties that make them attractive for future optoelectronic applications. Integration of TMDCs into practical all-dielectric heterostructures hinges on the ability to passivate and protect them against necessary fabrication steps on large scales. Despite its limited scalability, encapsulation of TMDCs in hexagonal boron nitride (hBN) currently has no viable alternative for achieving high performance of the final device. Here, we show that the novel, ultrathin Ga$_2$O$_3$ glass is an ideal centimeter-…
