The lift and drag forces acting on a small, neutrally-buoyant spherical particle in a single-wall-bounded linear shear flow are examined via numerical computation. The effects of shear rate are isolated from those of slip by setting the particle velocity equal to the local fluid velocity (zero slip), and examining the resulting hydrodynamic forces as a function of separation distance. In contrast to much of the previous numerical literature, low shear Reynolds numbers are considered ($10^{-3} \lesssim Re_γ \lesssim 10^{-1}$). This shear rate range is relevant when dealing with particulate flows within small channels, for example particle migration in microfluidic devices being used or developed for the biotech industry. We demonstrate a strong dependence of both the lift and drag forces on shear rate. Building on previous theoretical $Re_γ \ll 1$ studies, a wall-shear based lift correlation is proposed that is applicable when the wall lies both within the inner and outer regions of the disturbed flow. Similarly, we validate an improved drag correlation that includes higher order terms in wall separation distance that more accurately captures the drag force when the particle is close to, but not touching, the wall. Application of the new correlations shows that the examined shear based lift force is as important as the previously examined slip based lift force, highlighting the need to account for shear when predicting the near-wall movement of neutrally-buoyant particles.
Recent experiments found that a hot solid sphere that is able to sustain a stable Leidenfrost vapour layer in a liquid exhibits significant drag reduction during free fall. The variation of the drag coefficient with Reynolds number shows substantial deviation from the characteristic drag crisis behavior at high Reynolds numbers. Results obtained with liqiuds of different viscosities show that onset of the drag crisis depends on the viscosity ratio of the vapor to the liquid. The key feature of the vapour layer in facilitating tangential flow and in altering the behaviour of the boundary layer …
The lift and drag forces acting on a small spherical particle moving with a finite slip in single-wall-bounded flows are investigated via direct numerical simulations. The effect of slip velocity on the particle force is analysed as a function of separation distance for low slip and shear Reynolds numbers ($10^{-3} \leq Re_γ, Re_{\text{slip}} \leq 10^{-1}$) in both quiescent and linear shear flows. A generalised lift model valid for arbitrary particle-wall separation distances and $Re_γ, Re_{\text{slip}} \leq 10^{-1}$ is developed based on the results of the simulations. The proposed model can…
Superhydrophobic surfaces (SHSs) have the potential to reduce drag at solid boundaries. However, multiple independent studies have recently shown that small amounts of surfactant, naturally present in the environment, can induce Marangoni forces that increase drag, at least in the laminar regime. To obtain accurate drag predictions, one must solve the mass, momentum, bulk surfactant and interfacial surfactant conservation equations. This requires expensive simulations, thus preventing surfactant from being widely considered in SHS studies. To address this issue, we propose a theory for steady,…
Superhydrophobic surfaces (SHSs) can reduce the friction drag in turbulent flows. In the laminar regime, it has been shown that trace amounts of surfactant can negate this drag reduction, at times rendering these surfaces no better than solid walls (Peaudecerf et al., Proc. Natl. Acad. Sci. USA 114(28), 7254-9, 2017). However, surfactant effects on the drag-reducing properties of SHSs have not yet been studied under turbulent flow conditions, where predicting the effects of surfactant in direct numerical simulations remains expensive by today's standards. We present a model for turbulent flow …
The classical problem of the fluid mechanics is the problem of a supersonic motion around a thin body was generalized to the case of non-equilibrium gas. The drag and lift force coefficients were founded. It is shown that the drag and lift force coefficients in the acoustically active supersonic flow are both decreased
d'Alembert's paradox is the contradictory observation that for incompressible and inviscid (potential) fluid flow, there is no drag force experienced by a body moving with constant velocity relative to the fluid. This paradox can be straightforwardly resolved by considering Navier's slip boundary condition. Potential flow around a cylinder then solves the Navier--Stokes equations using friction parameter $β=-2ν$. This negative friction parameter can be interpreted physically as the fluid being accelerated by the cylinder wall. This explains the lack of drag. In this paper, we introduce the Nav…
Flow over bluff bodies has multiple engineering applications and thus, has been studied for decades. The lift and drag coefficients are practically important in the design of many components such as automobiles, aircrafts, buildings etc. These coefficients vary significantly with Reynolds number and geometric parameters of the bluff body. In this study, we have analyzed the sensitivity of lift and drag coefficients on single and tandem elliptic cylinders to cylinder aspect ratios, angles of attack, cylinder separation, and flow Reynolds number. Sensitivity analysis with Monte-Carlo algorithm r…
The drag reduction induced by superhydrophobic surfaces is investigated in turbulent pipe flow. Wetted superhydrophobic surfaces are shown to trap gas bubbles in their asperities. This stops the liquid from coming in direct contact with the wall in that location, allowing the flow to slip over the air bubbles. We consider a well defined texture with streamwise grooves at the walls in which the gas is expected to be entrapped. This configuration is modelled with alternating no-slip and shear-free boundary conditions at the wall. With respect to classical turbulent pipe flow, a substantial drag …
When a very thin capillary is inserted into a liquid, the liquid is sucked into it: this imbibition process is controlled by a balance of capillary and drag forces, which are hard to quantify experimentally, in particularly considering flow on the nanoscale. By computer experiments using a generic coarse-grained model, it is shown that an analysis of imbibition forced by a controllable external pressure quantifies relevant physical parameter such as the Laplace pressure, Darcy's permeability, effective pore radius, effective viscosity, dynamic contact angle and slip length of the fluid flowing…
We study numerically the two-dimensional flow past a circular cylinder as a prototypical transitional flow, and investigate the influence of a generic slip boundary condition on the wake dynamics. We show that slip significantly delays the onset of recirculation and shedding in the wake behind the cylinder. As expected, the drag on the cylinder decreases with slip, with an increased drag sensitivity for large Reynolds numbers. We also show that past the critical shedding Reynolds number, slip decreases the vorticity intensity in the wake, as well as the lift forces on the cylinder, but increas…
A numerical study of two-dimensional flow past a confined circular cylinder with slip wall is performed. A dimensionless number, Knudsen number ($Kn$) is used to describe the slip length of cylinder wall. The Reynolds number ($Re$) and Knudsen number ($Kn$) ranges considered are $Re = [1, 180]$ and $Kn = [0, \infty)$, respectively. Time-averaged flow separation angle ($\bar{θ_s}$), dimensionless recirculation length ($\bar{L_s}$) and the tangential velocity ($\bar{u_τ}$) distributed on the cylinder's wall, drag coefficient ($\bar{C_d}$) and drag reduction ($DR$) are investigated. The time-aver…
Owing to the multiscale nature and the consequent high computational cost associated with simulations of flows over rough surfaces, effective models are being developed as a practical means of dealing with such flows. Existing effective models focus primarily on accurately predicting interface velocities using slip length. Moreover, they are concerned mainly with flat interfaces and do not directly address the drag computation. In this work, we formulate the Transpiration-Resistance model in polar coordinates and address the challenge of computing drag components on rough surfaces. Like slip l…
Results are reported of an experimental investigation into the motion of a heavy cylinder free to move inside a water-filled drum rotating around a horizontal axis. The cylinder is observed to either co- or, counter intuitively, counter-rotate with respect to the rotating drum. The flow was measured with particle image velocimetry (PIV), and it was found that the inner cylinder significantly altered the bulk flow field from the solid-body rotation found for a fluid filled drum. In the counter-rotation case, the generated lift force allowed the cylinder to freely rotate without contact with the…
The underlying mechanisms of three different flow-control strategies on drag reduction in a channel flow are investigated by direct numerical simulations at friction Reynolds numbers ranging from 65 to 85. These strategies include the addition of long-chain polymers, the incorporation of slip surfaces, and the application of an external body force. While it has been believed that such methods lead to a skin-friction reduction by controlling near-wall flow structures, the underlying mechanisms at play are still not as clear. In this study, a temporal analysis is employed to elucidate underlying…
By means of lattice-Boltzmann simulations the drag force on a sphere of radius R approaching a superhydrophobic striped wall has been investigated as a function of arbitrary separation h. Superhydrophobic (perfect-slip vs. no-slip) stripes are characterized by a texture period L and a fraction of the gas area $ϕ$. For very large values of h/R we recover the macroscopic formulae for a sphere moving towards a hydrophilic no-slip plane. For h/R=O(1) and smaller the drag force is smaller than predicted by classical theories for hydrophilic no-slip surfaces, but larger than expected for a sphere in…
We conduct direct simulations of turbulent channels imposing different virtual origins for all three velocities using Robin, slip-like boundary conditions to study the effect of displacing the origins perceived by different flow components, a mechanism common to small-textured surfaces. We also explore this effect using opposition control. For riblets, Luchini et al. (1991) proposed that their effect could be reduced to the offset between the streamwise- and spanwise-velocity origins, the latter being the origin perceived by turbulence. Later results on superhydrophobic surfaces suggest that t…
The motion of a viscous drop is investigated when the interface is fully covered with a stagnant layer of surfactant in an arbitrary unsteady Stokes flow for the low surface Péclet number limit. The effect of the interfacial slip coefficient on the behavior of the flow field is also considered. The hydrodynamic problem is solved by the solenoidal decomposition method and the drag force is computed in terms of Faxen's laws using a perturbation ansatz in powers of the surface Péclet number. The analytical expressions for the migration velocity of the drop are also obtained in powers of the surfa…
In a recent paper, Liu, Zhu and Wu (2015, {\it J. Fluid Mech.} {\bf 784}: 304) present a force theory for a body in a two-dimensional, viscous, compressible and steady flow. In this companion paper we do the same for three-dimensional flow. Using the fundamental solution of the linearized Navier-Stokes equations, we improve the force formula for incompressible flow originally derived by Goldstein in 1931 and summarized by Milne-Thomson in 1968, both being far from complete, to its perfect final form, which is further proved to be universally true from subsonic to supersonic flows. We call this…
The hydrodynamic drag at a lipid bilayer surface determines in part the flow properties of suspensions of cells and liposomes. Given the fluidity of lipid bilayers, it is not obvious a priori whether solid-like no-slip, liquid-like no-stress, or intermediate boundary conditions apply at the water-bilayer interface. Though no-slip conditions have been widely assumed for many decades, this fundamental aspect of membrane rheology has, to our knowledge, never been directly measured for free bilayers. We applied light sheet fluorescence microscopy to image freely diffusing phospholipid vesicles and…
Anisotropic super-hydrophobic surfaces have the potential to greatly reduce drag and enhance mixing phenomena in microfluidic devices. Recent work has focused mostly on cases of super-hydrophobic stripes. Here, we analyze a relevant situation of cosine variation of the local slip length. We derive approximate formulae for maximal (longitudinal) and minimal (transverse) directional effective slip lengths that are in good agreement with the exact numerical solution and lattice-Bolzmann simulations for any surface slip fraction. The cosine texture can provide a very large effective (forward) slip…
Recently, experiments showed that forces on intruders dragged horizontally through dense, hydrostatic granular packings mainly depend on the local surface orientation and can be seen as the sum of the forces exerted on small surface elements. In order to understand such forces more deeply, we perform 2D soft-sphere molecular dynamics simulation, on similar set up, of an intruder dragged through a 50-50 bi-disperse granular packing, with diameters 0.30 and 0.34 cm. We measure, for both circular and half-circle shapes, the forces parallel (drag) and perpendicular (lift) to the drag direction as …
Unlike a helicopter, an insect can, in theory, use both lift and drag to stay aloft. Here we show that a dragonfly uses mostly drag to hover by employing asymmetric up and down strokes. Computations of a family of strokes further show that using drag can be as efficient as using lift at the low Reynolds number regime appropriate for insects.
Developing deterministic neighborhood-informed point-particle closure models using machine learning has garnered interest in recent times from dispersed multiphase flow community. The robustness of neural models for this complex multi-body problem is hindered by the availability of particle-resolved data. The present work addresses this unavoidable limitation of data paucity by implementing two strategies: (i) by using a rotation and reflection equivariant neural network and (ii) by pursuing a physics-based hierarchical machine learning approach. The resulting machine learned models are observ…
In this work, we investigate the dynamics of vortex-induced vibration of an elastically mounted cylinder with very low values of mass and damping. We use two methods to investigate this canonical problem: first we calculate the instantaneous phase between the cylinder motion and the fluid forcing; second we decompose the total hydrodynamic force into drag and lift components that act along and normal to, respectively, the instantaneous effective angle of attack. We focus on the phase dynamics in the large-amplitude-response range, consisting of the initial, upper and lower branches of response…
In this work, we analyze the inertial migration of an electrophoretic particle in a 2-D Poiseuille flow with an electric field applied parallel to the walls. For a thin electrical double layer, the particle exhibits a slip-driven electrokinetic motion along the direction of the applied electric field, which causes the particle to lead or lag the flow (depending on its surface charge). The fluid disturbance caused by this slip-driven motion is characterized by a rapidly decaying source-dipole field which alters the inertial lift on the particle. We determine this inertial lift using the recipro…
Lubrication forces depend to a high degree on elasticity, texture, charge, chemistry, and temperature of the interacting surfaces. Therefore, by appropriately designing surface properties, we may tailor lubrication forces to reduce friction, adhesion and wear between sliding surfaces or control repulsion, assembly, and collision of interacting particles. Here, we show that variations of slippage on one of the contacting surfaces induce a lift force. We demonstrate the consequences of this force on the mobility of a cylinder traveling near a wall and show the emergence of particle oscillation a…
We report on a series of fully resolved simulations of the flow around a rigid sphere translating steadily near a wall, either in a fluid at rest or in the presence of a uniform shear. Non-rotating and freely rotating spheres subject to a torque-free condition are both considered to evaluate the importance of spin-induced effects. The separation distance between the sphere and wall is varied from values at which the wall influence is weak down to gaps of half the sphere radius. The Reynolds number based on the sphere diameter and relative velocity with respect to the ambient fluid spans the ra…
In this paper, we applied the Shan-Chen multiphase Lattice Boltzmann method to simulate two different parameters, contact angle (a static parameter) and slip length (a dynamic parameter), and we proposed a relationship between them by fitting those numerical simulation results. By changing the values of the strength of interaction between fluid particles (SIF) and the strength of interaction between fluid and solid surface (SIFS), we simulated a series of contact angles and slip lengths. Our numerical simulation results show that both SIF and SIFS have little effects on the relationship betwee…
Patterned surfaces with large effective slip lengths, such as super-hydrophobic surfaces containing trapped gas bubbles, have the potential to reduce hydrodynamic drag. Based on lubrication theory, we analyze an approach of a hydrophilic disk to such a surface. The drag force is predicted analytically and formulated in terms of a correction function to the Reynolds equation, which is shown to be the harmonic mean of corrections expressed through effective slip lengths in the two principal (fastest and slowest) orthogonal directions. The reduction of drag is especially pronounced for a thin (co…
Flow control for turbulent skin-friction drag reduction is applied to a transonic airfoil to improve its aerodynamic performance. The study is based on direct numerical simulations (with up to 1.8 billions cells) of the compressible turbulent flow around a supercritical airfoil, at Reynolds and Mach numbers of $Re_\infty= 3 \times 10^5$ and $M_\infty =0.7$. Control via spanwise forcing is applied over a fraction of the suction side of the airfoil. Besides locally reducing friction, the control modifies the shock wave and significantly improves the aerodynamic efficiency of the airfoil by incre…
The actuator line model (ALM) is a commonly used method to represent lifting surfaces such as wind turbine blades within Large-Eddy Simulations (LES). In the ALM the lift and drag forces are replaced by an imposed body force which is typically smoothed over several grid points using a Gaussian kernel with some prescribed smoothing width $ε$. To date, the choice of $ε$ has most often been based on numerical considerations related to the grid spacing used in LES. However, especially for finely resolved LES with grid spacings on the order of or smaller than the chord-length of the blade, the best…
High-fidelity simulations are performed to study active flow control techniques for alleviating deep dynamic stall of a SD7003 airfoil in plunging motion. The flow Reynolds number is $Re=60{,}000$ and the freestream Mach number is $M=0.1$. Numerical simulations are performed with a finite difference based solver that incorporates high-order compact schemes for differentiation, interpolation and filtering on a staggered grid. A mesh convergence study is conducted and results show good agreement with available data in terms of aerodynamic coefficients. Different spanwise arrangements of actuator…
We analyze theoretically a high-speed drainage of liquid films squeezed between a hydrophilic sphere and a textured super-hydrophobic plane, that contains trapped gas bubbles. A super-hydrophobic wall is characterized by parameters $L$ (texture characteristic length), $b_1$ and $b_2$ (local slip lengths at solid and gas areas), and $ϕ_1$ and $ϕ_2$ (fractions of solid and gas areas). Hydrodynamic properties of the plane are fully expressed in terms of the effective slip-length tensor with eigenvalues that depend on texture parameters and $H$ (local separation). The effect of effective slip is p…
We explore the ability of anisotropic permeable substrates to reduce turbulent skin-friction, studying the influence that these substrates have on the overlying turbulence. For this, we perform DNSs of channel flows bounded by permeable substrates. The results confirm theoretical predictions, and the resulting drag curves are similar to those of riblets. For small permeabilities, the drag reduction is proportional to the difference between the streamwise and spanwise permeabilities. This linear regime breaks down for a critical value of the wall-normal permeability, beyond which the performanc…
The following note shows that the symmetry of various resistance formulae, often based on Lorentz reciprocity for linearly viscous fluids, applies to a wide class of non-linear viscoplastic fluids. This follows from Edelen's non-linear generalization of the Onsager relation for the special case of \emph{strongly dissipative} rheology, where constitutive equations are derivable from his dissipation potential. For flow domains with strong dissipation in the interior and on a portion of the boundary this implies strong dissipation on the remaining portion of the boundary, with strongly dissipativ…
Super Hydrophobic (SH) coatings are widely used to mitigate drag in various applications. Numerous studies have demonstrated that the beneficial wall-slip effect produced by these materials disappears in laminar flow regimes. The main mechanisms considered to be behind the decrease in performance are Marangoni-induced stresses and air/liquid interface deformation. In the present study, a new mechanism is proposed to explain the loss of performances of SH-surfaces in laminar flow regimes. Here we consider the flow of air inside the plastron and the associated momentum loses induced by roughness…
Data from direct numerical simulation of open channel flow over a geometrically rough wall at a bulk Reynolds number of 2900, generated by Chan-Braun et al. ["Force and torque acting on particles in a transitionally rough open-channel flow", J. Fluid Mech. 684, 441--474 (2011), 10.1017/jfm.2011.311] are further analysed with respect to the time and length scales of force and torque acting on the wall-mounted spheres. For the two sizes of spheres in a square arrangement (11 and 49 wall units in diameter, yielding hydraulically smooth and transitionally rough flow, respectively), the spatial str…
Deep reinforcement learning-based active flow control of an elliptical cylinder: transitioning from an elliptical cylinder to a circular cylinder and a flat plate
Severe contradictions exist between experimental observations and computational predictions regarding natural convective thermal transport in nanosuspensions. The approach treating nanosuspensions as homogeneous fluids in computations has been pin pointed as the major contributor to such contradictions. To fill the void, inter particle and particle fluid interactivities (slip mechanisms), in addition to effective thermophysical properties, have been incorporated within the present formulation. Through thorough scaling analysis, the dominant slip mechanisms have been identified. A Multi Compone…
