Spinel lithium manganese oxide (LixMn2O4) is used as an active material in battery cathodes. It is a relatively inexpensive and environmentally friendly material, but suffers from capacity fade during use. The capacity losses are generally attributed to the formation of the tetragonal phase (x > 1) due to overpotentials at the surfaces of the micron-sized particles that are used in commercial electrodes. In this study, we investigate the mechanisms of tetragonal phase formation by performing electrochemical lithiation (discharging) in-situ in the transmission electron microscope (TEM) utilizing diffraction and high resolution as well as spectroscopy. We observe a sharp interface between the cubic spinel (x = 1) and the tetragonal phase (x = 2), that moves under lithium diffusion-control. The tetragonal phase forms as a complex nanotwinned microstructure, presumably to relieve the stresses due to expansion during lithiation. We propose that the twinned microstructure stabilizes the tetragonal phase, adding to capacity loss upon deep discharge.
We report in situ measurements of stress evolution in a silicon thin-film electrode during electrochemical lithiation and delithiation by using the Multi-beam Optical Sensor (MOS) technique. Upon lithiation, due to substrate constraint, the silicon electrode initially undergoes elastic deformation, resulting in rapid rise of compressive stress. The electrode begins to deform plastically at a compressive stress of ca. -1.75 GPa; subsequent lithiation results in continued plastic strain, dissipating mechanical energy. Upon delithiation, the electrode first undergoes elastic straining in the oppo…
We report real-time average stress measurements on composite silicon electrodes made with two different binders [Carboxymethyl cellulose (CMC), and polyvinylidene fluoride (PVDF)] during electrochemical lithiation and delithiation. During galvanostatic lithiation at very slow rates, the stress in a CMC-based electrode becomes compressive and increases to 70 MPa, where it reaches a plateau and increases slowly thereafter with capacity. The PVDF-based electrode exhibits similar behavior, although with lower peak compressive stress of about 12 MPa. These initial experiments indicate that the stre…
In this work, the mechanism of Li insertion in $η'$-Cu$_6$Sn$_5$ to form Li$_2$CuSn is discussed in detail, based on both theoretical calculations and experimental results. The mechanism is investigated by means of first principles calculations, with the full potential linearized augmented plane wave method, in combination with {\it in situ} X-ray diffraction experiments. The $η'$-Cu$_6$Sn$_5$ structure, as well as its lithiated products, have been optimized and the electronic charge density calculated in order to study the change in bond character on lithiation. The average insertion voltage …
Crystalline to amorphous phase transformation during initial lithiation in (100) silicon-wafers is studied in an electrochemical cell with lithium metal as the counter and reference electrode. It is demonstrated that severe stress jumps across the phase boundary lead to fracture and damage, which is an essential consideration in designing silicon based anodes for lithium ion batteries. During initial lithiation, a moving phase boundary advances into the wafer starting from the surface facing the lithium electrode, transforming crystalline silicon into amorphous LixSi. The resulting biaxial com…
An in situ study of deformation, fracture, and fatigue behavior of silicon as a lithium-ion battery electrode material is presented. Thin films (100-200 nm) of silicon are cycled in a half-cell configuration with lithium metal foil as counter/reference electrode, with 1M lithium hexafluorophosphate in ethylene carbonate, diethylene carbonate, dimethyl carbonate solution (1:1:1, wt.%) as electrolyte. Stress evolution in the Si thin-film electrodes during electrochemical lithiation and delithiation is measured by monitoring the substrate curvature using the multi-beam optical sensing method. The…
An in situ study of stress evolution and mechanical behavior of germanium as a lithium-ion battery electrode material is presented. Thin films of germanium are cycled in a half-cell configuration with lithium metal foil as counter/reference electrode, with 1M LiPF6 in ethylene carbonate, diethyl carbonate, dimethyl carbonate solution (1:1:1, wt. %) as electrolyte. Real-time stress evolution in the germanium thin-film electrodes during electrochemical lithiation/delithiation is measured by monitoring the substrate curvature using the multi-beam optical sensing method. Upon lithiation a-Ge under…
The atomistic mechanisms during lithiation and delithiation of amorphous Si nanowires ($a$-SiNW) have been investigated over cycles by molecular dynamics simulations. First, the Modified Embedded Atom Method (MEAM) potential from Cui et al. [J. Power Sources. 2012, (207) 150] has been further optimized on static (Li$_x$Si alloy phases and point defect energies) and on dynamic properties (Li diffusion) to reproduce the lithiation of small crystalline Si nanowires calculated at the {\it ab initio} level. The lithiation of $a$-SiNW reveals a two-phase process of lithiation with a larger diffusion…
Cubic spinel Li$_{\rm 1+x}$Ti$_2$O$_4$ is a promising electrode material as it exhibits a high lithium diffusivity and undergoes minimal changes in lattice parameters during lithiation and delithiation, thereby ensuring favorable cycleability. The present work is a multi-physics and multi-scale study of Li$_{\rm 1+x}$Ti$_2$O$_4$ that combines first principles computations of thermodynamic and kinetic properties with continuum scale modeling of lithiation-delithiation kinetics. Density functional theory calculations and statistical mechanics methods are used to calculate lattice parameters, ela…
As a typical immiscible binary system, copper (Cu) and lithium (Li) show no alloying and chemical intermixing under normal circumstances. A notable example that takes advantages of the immiscibility between Cu and Li is the widespread utilization of Cu foils as the anodic current collector in Li-ion batteries. Here we show that the nanoscale size effect can play a subtle yet critical role in mediating the chemical activity of Cu and therefore its miscibility with Li, such that the electrochemical alloying and solid-state amorphization will occur in such an immiscible system when decreasing Cu …
Fabrics of continuous fibers of carbon nanotubes (CNTFs) are attractive materials for multifunctional energy storage devices, either as current collector, or as active material. Despite a similar chemical composition, lithiation/delithiation in CNTFs is substantially different from traditional graphite electrodes. In CNTFs this process is dominated by surface processes, insertion in the bundles interstices, electrochemical doping and often-overlooked partial degradation of the sp2 lattice upon cycling. Through extensive electrochemical analysis, together with in situ Raman spectroscopy measure…
Obtaining a complete picture of local processes still poses a significant challenge in battery research. Here we demonstrate an in-situ combination of multimodal neutron imaging with neutron diffraction for spatially resolved operando observations of the lithiation-delithiation of a graphite electrode in a Li-ion battery cell. Throughout the lithiation-delithiation process we image the Li distribution based on the local beam attenuation. Simultaneously, we observe the development of the lithiated graphite phases as a function of cycling time and electrode thickness and integral throughout its …
It is shown that continuously occurring electrolyte-reduction reaction on freshly-exposed electrode surfaces during lithiation/delithiation cycles causes the lowering of cycling efficiency, and hence, capacity fade in well-cycled silicon anodes in lithium-ion batteries. Using galvanostatic lithiation/delithiation data from multiple cycles on a Li/Si half-cell, a methodology to separate the charge due to the main reaction (lithiation/delithiation of Si) from the side-reaction (electrolyte-reduction) is presented. The rate of this parasitic side reaction is estimated on well-cycled amorphous sil…
We report in situ measurement of biaxial moduli of a Si thin-film electrode as a function of its lithium concentration. During lithiation, biaxial compressive stress is induced in the Si film and it undergoes plastic flow. At any state-of-charge (SOC), a relatively small delithiation-relithiation sequence unloads and reloads the film elastically. From the stress and strain changes during a delithiation-relithiation cycle, the biaxial modulus of the film is calculated. Stress change is obtained by measuring the change in substrate curvature using a Multi-beam Optical Sensor; the elastic strain …
A major challenge in the development of new battery materials is understanding their fundamental mechanisms of operation and degradation. Their microscopically inhomogeneous nature calls for characterization tools that provide operando and localized information from individual grains and particles. Here we describe an approach that images the nanoscale distribution of ions during electrochemical charging of a battery in a transmission electron microscope liquid flow cell. We use valence energy-loss spectroscopy to track both solvated and intercalated ions, with electronic structure fingerprint…
Composite cathode coatings made of a high energy density layered oxide (Li1.2Ni0.15Mn0.55Co0.1O2, theoretical capacity ~377 mAh/g), polyvinylidene fluoride (PVdF) binder, and electron-conduction additives, were bonded to an elastic substrate. An electrochemical cell, built by pairing the cathode with a capacity-matched graphite anode, was electrochemically cycled and the real-time average stress evolution in the cathode coating was measured using a substrate-curvature technique. Features in the stress evolution profile showed correlations with phase changes in the oxide, thus yielding data com…
Gadolinium-doped ceria was studied in a half SOFCs at elevated temperatures. In situ electron holography could reveal ionic activity in a single GDC-Pt interface at the elevated temperatures that result in further oxidation of the GDC. In situ EELS measurements confirmed holography results and showed the existence of the gadolinium in a new oxidation state. Also, it was found that the doped cations are the active ions in the oxygen evolution reaction from the solid oxide electrolyte.
The properties of the mixed system LiBH4 LiCl P2S5 are studied with respect to all-solid-state batteries. The studied material undergoes an amorphization upon heating above 601C, accompanied with increased Li+ conductivity beneficial for battery electrolyte applications. The measured ionic conductivity is 10-3 Scm-1 at room temperature with an activation energy of 0.40(2) eV after amorphization. Structural analysis and characterization of the material suggest that BH4 groups and PS4 may belong to the same molecular structure, where Cl ions interplay to accommodate the structural unit. Thanks t…
Various bandstructure engineering methods have been studied to improve the performance of graphitic transparent conductors; however none demonstrated an increase of optical transmittance in the visible range. Here we measure in situ optical transmittance spectra and electrical transport properties of ultrathin-graphite (3-60 graphene layers) simultaneously via electrochemical lithiation/delithiation. Upon intercalation we observe an increase of both optical transmittance (up to twofold) and electrical conductivity (up to two orders of magnitude), strikingly different from other materials. Tran…
A dedicated in situ heating setup in a scanning electron microscope (SEM) followed by an ex situ atomic force microscopy (AFM) and electron backscatter diffraction (EBSD) is used to characterize the nucleation and early growth stages of Fe-Al intermetallics (IMs) at 596 °C. A location tracking is used to interpret further characterization. Ex situ AFM observations reveal a slight shrinkage and out of plane protrusion of the IM at the onset of IM nucleation followed by directional growth. The formed interfacial IM compounds were identified by ex situ EBSD. It is now clearly demonstrated that th…
In situ straining experiments were performed in a TEM on an equimolar CoCrFeMnNi (Cantor) high entropy alloy at room and cryogenic temperature. Perfect and partial dislocation activity were recorded in both cases. Twinning directly follows the development of partial dislocation shearing that has various origins (perfect dislocation splitting, anchoring). It is shown that, although twinning is more frequently observed at liquid nitrogen temperature, its prevalence depends mainly on crystal orientation. As a result, twinning and perfect dislocation plasticity are likely to occur jointly in rando…
The mechanisms of deformation and failure of Cu/Nb nanolaminates manufactured by accumulated roll bonding were analysed using in-situ TEM mechanical tests. Dog-bone small-scale tensile specimens were prepared using a FIB-based technique with the layers parallel and perpendicular to the loading axis. Load, deformation and TEM micrographs were recorded during the in-situ TEM mechanical tests. The specimens deformed parallel to the layers presented very high strain hardening and ductility while those deformed in the perpendicular orientation were more brittle. These results were rationalized in t…
We present a comparative ab initio study of Li, Na, and Mg storage in tin, including phononic effects and phase competition between alpha and beta Sn. Mg doping at low concentration is found to stabilize the beta phase. On the contrary, Li and Na doping is shown to reverse the stability of the phases at room temperature: Li/Na-doped alpha-Sn is more stable than Li/Na-doped beta-Sn up to a temperature of around 380/400 K. This may rationalize the formation of alpha-Sn upon lithiation and delithiation of beta-Sn anodes reported in experimental studies. The changes in phase stability with Li/Na/M…
TEM specimens from potassium niobate single crystals were observed while being heated in a TEM. DWs and dislocations were observed; the DWs were mobile. In certain cases the DWs became pinned by the dislocations, at least for a short time, most likely due to interaction of strain fields. Both phase changes were observed with accompanying rapid appearance of new domain patterns.
The dissociative chemisorption of molecular nitrogen on clean lanthanide surfaces at ambient temperature and low pressure is explored. In-situ conductance measurements track the conversion from the lanthanide metals to the insulating lanthanide nitrides. A small partial pressure of oxygen ($\sim 10^{-8}$ mbar) is shown to inhibit the nitridation of lanthanides at $10^{-4}$ mbar of N$_2$. The rate of nitridation as a function of nitrogen pressure is measured at low pressure for a series of lanthanide elements, gadolinium, terbium, dysprosium, ytterbium and praseodymium. Exposure of the lanthani…
The evolution of a continuous Fe(NO3)3 catalyst film was observed by in-situ annealing in a Transmission Electron Microscope (TEM). Such catalysts are routinely used in the catalytic growth of carbon nanotubes. The experiments reveal that crystalline particles form from the gel-like film already around 300C. At usual carbon nanotube growth temperatures of 700C, the particles are single-crystalline with a log-normal size distribution. The observations furthermore show that in spite of the crystalline structure of the particles there is a high mobility. The experiments allow to obtain detailed i…
An experimental setup for determining the electrical resistivity of several types of thermoelectric materials over the temperature range 20 < T < 550 C is described in detail. One resistivity measurement during temperature cycling is also explained for Cu0.01Bi2Te2.7Se0.3 while a second measurement is made on Yb0.35Co4Sb12 as a function of time at 400 C. Both measurements confirm that the materials are thermally stable for the temperature range and time period measured. Measurements made during temperature cycling show an irreversible decrease in the electrical resistivity of Cu0.01Bi2Te2.7Se0…
Thin foils of the double solid solution $(Zr{_0.5},Ti{_0.5})_{2}(Al_{0.5},Sn_{0.5})C$ MAX phase were in situ irradiated in a transmission electron microscope (TEM) up to a fluence of $1.3\times10^{17} ions$ $cm^{-2}$ (${\sim}$ 7.5 dpa), using 6 keV $He^{+}$ ions. Irradiations were performed in the 350-800 °C temperature range. In situ and post-irradiation examination (PIE) by TEM was used to study the evolution of irradiation-induced defects as function of dose and temperature. Spherical He bubbles and string-like arrangements thereof, He platelets, and dislocation loops were observed. Disloca…
High entropy alloys are a class of materials with many significant improvements in terms of mechanical properties as compared to ``classical'' alloys. The corresponding structure-property relations are not yet entirely clear, but it is commonly believed that the good mechanical performance is strongly related to dislocation interactions with the complex energy landscape formed due to alloying. Although in-situ Transmission Electron Microscopy (TEM) allows high-resolution studies of the structure and dynamics of moving dislocations and makes the local obstacle/energy ``landscape'' directly visi…
Additive manufacturing (AM) by laser powder bed fusion (L-PBF) leads to the formation of a rich, hierarchical microstructure, including dislocation cell structures and elemental segregation. This structure has profound impacts on the corrosion behavior and mechanical properties of printed materials. In this study, we use in situ liquid cell scanning transmission electron microscope (STEM) to directly characterize the nanoscale origins of corrosion initiation in AM 316L stainless steel. Under applied anodic potentials, we found that the dislocation cellular boundaries were preferentially corrod…
Deformation twinning in hexagonal crystals is often considered as a way to palliate the lack of independent slip systems. This mechanism might be either exacerbated or shut down in small-scale crystals whose mechanical behavior can significantly deviate from bulk materials. Here, we show that sub-micron beryllium fibers initially free of dislocation and tensile tested in-situ in a transmission electron microscope (TEM) deform by a $\{ 10\bar{1}2 \}$ $\langle 10\bar{1}1 \rangle$ twin thickening. The propagation speed of the twin boundary seems to be entirely controlled by the nucleation of twin…
The degradation of liquid dispersed titanium (IV) sulphide (TiS$_2$) is studied from the point of view of oxidisation. TiS$_2$ is a layered two-dimensional nanomaterial, with potential for energy storage applications. However, flakes in dispersion were observed to degrade. We examined two oxidisation routes: deionised water at room temperature and oxygen gas within the temperature range 150-350°C. Water was seen to slowly oxidise flakes inwards from the edge, forming an amorphous oxide, a result comparable to the state of flakes which degraded within the original dispersion. Oxygen gas was see…
Combining Synchrotron X-ray Diffraction, Mechanistic Modeling, and Machine Learning for In Situ Subsurface Temperature Quantification during Laser Melting
The effect of silica-promotion on the reduction of iron oxides in hydrogen was investigated using in situ X-ray diffraction and aberration-corrected transmission electron microscopy to understand the mechanism of reduction and the identity of the iron(II) silicate phase that has historically been designated as the cause of the iron-silica interaction in such materials. In the absence of a silica promoter the reduction of hematite to α-Fe proceeds via magnetite. Silica promoted amorphous iron oxide is reduced to α-Fe via stable magnetite and wüstite phases. During reduction of silica-promoted i…
Understanding the phase transition mechanisms in two-dimensional (2D) materials is a key to precisely tailor their properties at the nanoscale. Molybdenum ditelluride (MoTe2) exhibits multiple phases at room temperature, making it a promising candidate for phase-change applications. Here, we fabricate lateral 2H-Td interfaces with laser irradiation and probe their phase transitions from micro- to atomic scales with in situ heating in the transmission electron microscope (TEM). By encapsulating the MoTe2 with graphene protection layers, we create an in situ reaction cell compatible with atomic …
Understanding the mechanism of martensitic transformation is of great importance in developing advanced high strength steels, especially TRansformation-Induced Plasticity (TRIP) steels. The TRIP effect leads to enhanced work-hardening rate, postponed onset of necking and excellent formability. In-situ transmission electron microscopy has been performed to systematically investigate the dynamic interactions between dislocations and alpha martensite at microscale. Local stress concentrations, e.g. from notches or dislocation pile-ups, render free edges and grain boundaries favorable nucleation s…
The lifetime and performance of any engineering component, from nanoscale sensors to macroscopic structures, are strongly influenced by fracture processes. Fracture itself is a highly localized event; originating at the atomic scale by bond breaking between individual atoms close to the crack tip. These processes, however, interact with defects such as dislocations or grain boundaries and influence phenomena on much larger length scales, ultimately giving rise to macroscopic behavior and engineering-scale fracture properties. This complex interplay is the fundamental reason why identifying the…
We present the first use of in situ far-infrared spectroscopy to analyze the thermal amorphization of a zeolitic imidazolate framework material. We explain the nature of vibrational motion changes during the amorphization process and reveal new insights into the effect that temperature has on the Zn-N tetrahedra.
We report a detailed high-temperature powder neutron diffraction investigation of the structural behavior of the multiferroic GaFeO3 between 296 and 1368 K. Temperature dependent neutron diffraction patterns do not show any appreciable change either in intensity or appearance/disappearance of the observed peaks upto 1368 K, ruling out any structural transition in the entire temperature range. The lattice parameters and volume exhibit normal thermal expansion behaviour, indicating the absence of any structural changes with increasing temperature. The origin of the magnetoelectric couplings and …
Thermal Corrections and Analysis on the Phase Stability of CsPbCl3 and Cs2AgSbCl6 during In-Situ Thermal Treatment
University of Maine（缅因大学）；Frontier Institute for Research in Sensor Technologies, University of Maine（缅因大学前沿传感技术研究机构）；Arizona State University（亚利桑那州立大学）；University of Central Florida（中佛罗里达大学）
The Zn K-edge X-ray absorption spectroscopy has been used to investigate in situ the decomposition of zinc peroxide (ZnO$_2$) to zinc oxide (ZnO). Principal component and linear combination analyses of the EXAFS spectra have been employed to identify the phase composition of the oxide upon heating to 900$^\circ$C. Only the ZnO$_2$ phase has been found up to 180$^\circ$C, whereas only the nanocrystalline ZnO phase has occurred above 250$^\circ$C. Detailed structural information on the temperature dependence of the local environment of zinc atoms has been obtained using the reverse Monte Carlo s…
There is a long-standing technological problem in which a stress dwell during cyclic loading at room temperature in Ti causes a significant fatigue life reduction. It is thought that localised time dependent plasticity in soft grains favourably oriented for easy plastic slip leads to load shedding and an increase in stress within a neighbouring hard grain poorly oriented for easy slip. Quantifying this time dependent plasticity process is key to understand the complex cold dwell fatigue problem. Knowing the effect of operating temperature and oxygen content on cold dwell fatigue will be benefi…
Upon insertion and extraction of lithium, materials important for electrochemical energy storage can undergo changes in thermal conductivity ($Λ$) and elastic modulus ($\it M$). These changes are attributed to evolution of the intrinsic thermal carrier lifetime and interatomic bonding strength associated with structural transitions of electrode materials with varying degrees of reversibility. Using in situ time-domain thermoreflectance (TDTR) and picosecond acoustics, we systemically study $Λ$ and $\it M$ of conversion, intercalation and alloying electrode materials during cycling. The interca…
Fundamental solid state physics phenomena typically occur at very low temperatures, requiring liquid helium cooling in experimental studies. Transmission electron microscopy is a well-established characterization method, which allows probing crucial materials properties down to nanometer and even atomic resolution. Due to the limited space in the object plane, however, suitable liquid-helium cooling is very challenging. To overcome this limitation, resolving power was sacrificed in our Dresden in-situ (S)TEM special, resulting in more than 60 mm usable experimental space in all directions with…
We report on advanced in-situ magneto-transport measurements in a transmission electron microscope. The approach allows for concurrent magnetic imaging and high resolution structural and chemical characterization of the same sample. Proof-of-principle in-situ Hall measurements on presumably undemanding nickel thin films supported by micromagnetic simulations reveal that in samples with non-trivial structures and/or compositions, detailed knowledge of the latter is indispensable for a thorough understanding and reliable interpretation of the magneto-transport data. The proposed in-situ approach…
