In this paper, we consider the power minimization problem of joint physical resource block (PRB) assignment and transmit power allocation under specified delay and reliability requirements for ultra-reliable and low-latency communication (URLLC) in downlink cellular orthogonal frequency-division multiple-access (OFDMA) system. To be more practical, only the imperfect channel state information (CSI) is assumed to be available at the base station (BS). The formulated problem is a combinatorial and mixed-integer nonconvex problem and is difficult to tackle. Through techniques of slack variables introduction, the first-order Taylor approximation and reweighted $\ell_1$-norm, we approximate it by a convex problem and the successive convex approximation (SCA) based iterative algorithm is proposed to yield sub-optimal solutions. Numerical results provide some insights into the impact of channel estimation error, user number, the allowable maximum delay and packet error probability on the required system sum power.
This paper investigates the resource allocation algorithm design for intelligent reflecting surface (IRS) aided multiple-input single-output (MISO) orthogonal frequency division multiple access (OFDMA) multicell networks, where a set of base stations cooperate to serve a set of ultra-reliable low-latency communication (URLLC) users. The IRS is deployed to enhance the communication channel and increase reliability by creating a virtual line of sight for URLLC users with unfavorable propagation conditions. This is the first study on IRS-enhanced OFDMA-URLLC systems. The resource allocation algor…
This paper considers the resource allocation algorithm design for downlink multiple-input single-output (MISO) orthogonal frequency division multiple access (OFDMA) ultra-reliable low latency communication (URLLC) systems. To meet the stringent delay requirements of URLLC, short packet transmission is adopted and taken into account for resource allocation algorithm design. The resource allocation is optimized for maximization of the weighted system sum throughput subject to quality-of-service (QoS) constraints regarding the URLLC users' number of transmitted bits, packet error probability, and…
In this paper, we investigate the worst-case robust beamforming design and resource block (RB) assignment problem for total transmit power minimization of the central controller while guaranteeing each robot's transmission with target number of data bits and within required ultra-low latency and extremely high reliability. By using the property of the independence of each robot's beamformer design, we can obtain the equivalent power control design form of the original beamforming design. The binary RB mapping indicators are transformed into continuous ones with additional $\ell_0$-norm constra…
In this paper, we study resource allocation algorithm design for multiuser orthogonal frequency division multiple access (OFDMA) ultra-reliable low latency communication (URLLC) in mobile edge computing (MEC) systems. To achieve the stringent end-to-end delay and reliability requirements of URLLC MEC systems, we propose joint uplink-downlink resource allocation and finite blocklength transmission. Furthermore, we propose a partial time overlap between the uplink and downlink frames to minimize the end-to-end delay, which introduces new time causality constraints. Then, the proposed resource al…
In this paper, we study resource allocation algorithm design for multi-user orthogonal frequency division multiple access (OFDMA) ultra-reliable low latency communication (URLLC) in mobile edge computing (MEC) systems. To meet the stringent end-to-end delay and reliability requirements of URLLC MEC systems, we propose joint uplink-downlink resource allocation and finite blocklength transmission. Furthermore, we employ a partial time overlap between the uplink and downlink frames to minimize the end-to-end delay, which introduces a new time causality constraint. The proposed resource allocation…
Recently, the sparse vector code (SVC) is emerging as a promising solution for short-packet transmission in massive machine type communication (mMTC) as well as ultra-reliable and low-latency communication (URLLC). In the SVC process, the encoding and decoding stages are jointly modeled as a standard compressed sensing (CS) problem. Hence, this paper aims at improving the decoding performance of SVC by optimizing the spreading matrix (i.e. measurement matrix in CS). To this end, two greedy algorithms to minimize the mutual coherence value of the spreading matrix in SVC are proposed. Specially,…
In this paper, a multi-objective optimization problem (MOOP) is proposed for maximizing the achievable finite blocklength (FBL) rate while minimizing the utilized channel blocklengths (CBLs) in a reconfigurable intelligent surface (RIS)-assisted short packet communication system. The formulated MOOP has two objective functions namely maximizing the total FBL rate with a target error probability, and minimizing the total utilized CBLs which is directly proportional to the transmission duration. The considered MOOP variables are the base station (BS) transmit power, number of CBLs, and passive b…
In this paper, we study ultra-reliable and low-latency communication (URLLC) under fading using multiple frequency or time bins. We investigate an approach to find an upper-bound on the packet error rate when a finite-length code is used. From simulation results, we find that the bound is reasonably tight for wide ranges of signal-to-noise ratio (SNR) and the number of multiple bins. Thus, the derived bound can be used to determine key parameters to guarantee the performance of URLLC in terms of the packet error rate.
In this paper, the average achievable rate of a re-configurable intelligent surface (RIS) aided factory automation is investigated in finite blocklength (FBL) regime. First, the composite channel containing the direct path plus the product of reflected paths through the RIS is characterized. Then, the distribution of the received signal-to-noise ratio (SNR) is matched to a Gamma random variable whose parameters depend on the total number of RIS elements as well as the channel pathloss. Next, by assuming FBL model, the achievable rate expression is identified and the corresponding average rate …
In this paper, we consider a smart factory scenario where a set of actuators receive critical control signals from an access point (AP) with reliability and low latency requirements. We investigate jointly active beamforming at the AP and passive phase shifting at the reconfigurable intelligent surface (RIS) for successfully delivering the control signals from the AP to the actuators within a required time duration. The transmission follows a two-stage design. In the first stage, each actuator can both receive the direct signal from AP and the reflected signal from the RIS. In the second stage…
In this paper, we adapt to cell-free Massive MIMO (multiple-input multiple-output) the finite-blocklength framework introduced by Östman et al. (2020) for the characterization of the packet error probability achievable with Massive MIMO, in the ultra-reliable low-latency communications (URLLC) regime. The framework considered in this paper encompasses a cell-free architecture with imperfect channel-state information, and arbitrary linear signal processing performed at a central-processing unit connected to the access points via fronthaul links. By means of numerical simulations, we show that, …
In this paper, we propose a network coding (NC) based approach to ultra-reliable low-latency communication (URLLC) over erasure channels. In transmitting multiple data packets, we demonstrate that the use of random NC can improve the reliability in terms of decoding error probability, while it incurs a longer decoding delay than a well-known K-repetition. To avoid a long decoding delay, we consider a sliding NC (SNC) design that allows a highly reliable transmission of each data packet with a guaranteed decoding delay. A few design examples are derived and their decoding error rates are analyz…
In this paper, we investigate the effectiveness of the hybrid automatic repeat request (HARQ) technique in providing high-reliability and low-latency in the finite blocklength (FBL) regime in a single user uplink scenario. We characterize the packet error rate (PER), throughput, and delay performance of chase combining HARQ (CC-HARQ) and incremental redundancy HARQ (IR-HARQ) in AWGN and Rayleigh fading channel with $m$ retransmissions. Furthermore, we consider a quasi-static fading channel model, which is more accurate than the over-simplified i.i.d. block fading or same channel assumption ove…
In URLLC, short packet transmission is adopted to reduce latency, such that conventional Shannon's capacity formula is no longer applicable, and the achievable data rate in finite blocklength becomes a complex expression with respect to the decoding error probability and the blocklength. To provide URLLC service in a factory automation scenario, we consider that the central controller transmits different packets to a robot and an actuator, where the actuator is located far from the controller, and the robot can move between the controller and the actuator. In this scenario, we consider four fu…
GNN-Based Polarforming for Multi-User MISO Short-Packet URLLC under Imperfect CSI
Pasargad Institute for Advanced Innovative Solutions (PIAIS)（帕萨加德先进创新解决方案研究所）；Department of Electrical Engineering, Sharif University of Technology（谢里夫理工大学电气工程系）；Department of Electrical Engineering, Amirkabir University of Technology（阿米尔卡比尔理工大学电气工程系）；Interdisciplinary Centre for Security, Reliability and Trust (SnT), University of Luxembourg（卢森堡大学安全、可靠性与信任跨学科中心）；Department of Electrical and Computer Engineering, University of Cyprus（塞浦路斯大学电气与计算机工程系）
This paper reviews the potential channel decoding techniques for ultra-reliable low-latency communications (URLLC). URLLC is renowned for its stringent requirements including ultra-reliability, low end-to-end transmission latency, and packet-size flexibility. These requirements exacerbate the difficulty of the physical-layer design, particularly for the channel coding and decoding schemes. To satisfy the requirements of URLLC, decoders must exhibit superior error-rate performance \black{and} low decoding complexity. \black{Also, it is desired that decoders be universal} to accommodate various …
Ultra-reliable low-latency communications (URLLC) has been considered as one of the three new application scenarios in the \emph{5th Generation} (5G) \emph {New Radio} (NR), where the physical layer design aspects have been specified. With the 5G NR, we can guarantee the reliability and latency in radio access networks. However, for communication scenarios where the transmission involves both radio access and wide area core networks, the delay in radio access networks only contributes to part of the \emph{end-to-end} (E2E) delay. In this paper, we outline the delay components and packet loss p…
Supporting ultra-reliable and low-latency communications (URLLC) is one of the major goals for the fifth-generation cellular networks. Since spectrum usage efficiency is always a concern, and large bandwidth is required for ensuring stringent quality-of-service (QoS), we minimize the total bandwidth under the QoS constraints of URLLC. We first propose a packet delivery mechanism for URLLC. To reduce the required bandwidth for ensuring queueing delay, we consider a statistical multiplexing queueing mode, where the packets to be sent to different devices are waiting in one queue at the base stat…
Ultra-reliable low latency communication (URLLC) is one of three primary use cases in the fifth-generation (5G) networks, and its research is still in its infancy due to its stringent and conflicting requirements in terms of extremely high reliability and low latency. To reduce latency, the channel blocklength for packet transmission is finite, which incurs transmission rate degradation and higher decoding error probability. In this case, conventional resource allocation based on Shannon capacity achieved with infinite blocklength codes is not optimal. Security is another critical issue in mis…
Ultra reliable and low latency communication (URLLC) is a newly introduced service category in 5G to support delay-sensitive applications. In order to support this new service category, 3rd Generation Partnership Project (3GPP) sets an aggressive requirement that a packet should be delivered with 10^-5 packet error rate within 1 ms transmission period. Since the current wireless transmission scheme designed to maximize the coding gain by transmitting capacity achieving long codeblock is not relevant for this purpose, a new transmission scheme to support URLLC is required. In this paper, we pro…
We propose to use channel inversion power control (CIPC) to achieve one-way ultra-reliable and low-latency communications (URLLC), where only the transmission in one direction requires ultra reliability and low latency. Based on channel reciprocity, our proposed CIPC schemes guarantee the power of received signal that is used to decode the information to be a constant value $Q$, by varying the transmit signal and power, which relaxes the assumption of knowing channel state information (CSI) at the user. Thus, the CIPC schemes eliminate the overhead of CSI feedback, reduce communication latency…
Ultra-reliable and low-latency communications (URLLC) is expected to be supported without compromising the resource usage efficiency. In this paper, we study how to maximize energy efficiency (EE) for URLLC under the stringent quality of service (QoS) requirement imposed on the end-to-end (E2E) delay and overall packet loss, where the E2E delay includes queueing delay and transmission delay, and the overall packet loss consists of queueing delay violation, transmission error with finite blocklength channel codes, and proactive packet dropping in deep fading. Transmit power, bandwidth and numbe…
The Fourth Industrial Revolution (Industrial 4.0) is coming, and this revolution will fundamentally enhance the way the factories manufacture products. The conventional wired lines connecting central controller to robots or actuators will be replaced by wireless communication networks due to its low cost of maintenance and high deployment flexibility. However, some critical industrial applications require ultra-high reliability and low latency communication (URLLC). In this paper, we advocate the adoption of massive multiple-input multiple output (MIMO) to support the wireless transmission for…
Mission-critical applications require Ultra-Reliable Low Latency (URLLC) wireless connections, where the packet error rate (PER) goes down to $10^{-9}$. Fulfillment of the bold reliability figures becomes meaningful only if it can be related to a statistical model in which the URLLC system operates. However, this model is generally not known and needs to be learned by sampling the wireless environment. In this paper we treat this fundamental problem in the simplest possible communication-theoretic setting: selecting a transmission rate over a dynamic wireless channel in order to guarantee high…
Driven by the explosive growth of Internet of Things (IoT) devices with stringent requirements on latency and reliability, ultra-reliability and low latency communication (uRLLC) has become one of the three key communication scenarios for the fifth generation (5G) and beyond 5G communication systems. In this paper, we focus on the beamforming design problem for the downlink multiuser uRLLC systems. Since the strict demand on the reliability and latency, in general, short packet transmission is a favorable form for uRLLC systems, which indicates the literature Shannon's capacity formula is no l…
Harbin Engineering University（哈尔滨工程大学）；University of Washington（华盛顿大学）
The extremely long underwater channel delay spread causes severe inter-symbol interference (ISI) for underwater acoustic communications. Passive time reversal processing (PTRP) can effectively reduce the channel time dispersion in a simple way via convolving the received packet with a time reversed probe signal. However the probe signal itself may introduce extra noise and interference (self-correlation of the probe signal). In this paper, we propose a virtual time reversal processing (VTRP) for single input single output (SISO) Orthogonal Frequency Division Multiplexing (OFDM) systems. It con…
There have been recent attempts to develop scheduling schemes for downlink transmission in a single cell of a multi-channel (e.g., OFDM-based) cellular network. These works have been quite promising in that they have developed low-complexity index scheduling policies that are delay-optimal (in a large deviation rate-function sense). However, these policies require that the channel is ON or OFF in each time-slot with a fixed probability (i.e., there is no memory in the system), while the reality is that due to channel fading and doppler shift, channels are often time-correlated in these cellula…
Ultra-Reliable Low Latency Communication (URLLC) is one of the distinctive features of the upcoming 5G wireless communication, going down to packet error rates (PER) of $10^{-9}$. In this paper we discuss the statistical properties of the wireless channel models that are relevant for characterization of the lower tail of the Cumulative Distribution Function (CDF). We show that, for a wide range of channel models, the outage probability at URLLC levels can be approximated by a simple power law expression, whose exponent and offset depend on the actual channel model. The main insights from the a…
All practical OFDM systems require a prefix to eliminate inter-symbol interference at the receiver. Cyclic prefix (CP) and zero-padding are well-known prefix construction methods, the former being the most employed technique in practice due to its lower complexity. In this paper we construct an OFDM system with a generalized CP. It is shown that the proposed generalized prefix effectively makes the channel experienced by the packet different from the actual channel. Using an optimization procedure, lower bit error rates can be achieved, outperforming other prefix construction techniques. At th…
The underwater acoustic channel continues to present significant challenges to efficient throughput performance of underwater acoustic sensor networks (UASNs) in varying scenarios. As a result, cross-layer approaches that explore joint PHY/MAC strategies are worthy of further exploration. We consider a recent high-speed OFDM modem and propose a new cross-layer solution based on modified CSMA/CA, for a canonical star network topology with few nodes (the most common scenario in UASNs). Some innovations to an adaptive OFDM PHY link are developed to jointly select the modulation, convolutional cod…
In this letter, we analyze the achievable rate of ultra-reliable low-latency communications (URLLC) in a randomly modeled wireless network. We use two mathematical tools to properly characterize the considered system: i) stochastic geometry to model spatial locations of the transmitters in a network, and ii) finite block-length analysis to reflect the features of the short-packets. Exploiting these tools, we derive an integral-form expression of the decoding error probability as a function of the target rate, the path-loss exponent, the communication range, the density, and the channel coding …
Beamforming and Resource Allocation for Delay Minimization in RIS-Assisted OFDM Systems
National Mobile Communications Research Laboratory, Southeast University, Nanjing 210096, China（南京东南大学国家移动通信研究中心）；College of Electronics and Information Engineering, Shenzhen University, Shenzhen 518060, China（深圳大学电子与信息工程学院）；Purple Mountain Laboratories, Nanjing 211111, China（紫金山实验室）；Centre for Wireless Innovation (CWI), Queen’s University Belfast, BT7 1NN Belfast, U.K.（女王大学贝尔法斯特无线创新中心）
Multi-connectivity offers diversity in terms of multiple interfaces through which the data can be sent, thereby improving simultaneously the overall reliability and latency. This makes interface diversity a natural candidate for supporting Ultra-Reliable Low Latency Communications (URLLC). This work investigates how the packet error statistics from different interfaces impacts the overall reliability-latency characteristics. We use the simple Gilbert-Elliott model for burst errors and estimate its parameters based on experimental measurement traces from LTE and {Wi-Fi} packet transmissions col…
We study multipath parameter estimation from orthogonal frequency division multiplex signals transmitted over doubly dispersive mobile radio channels. We are interested in cases where the transmission is long enough to suffer time selectivity, but short enough such that the time variation can be accurately modeled as depending only on per-tap linear phase variations due to Doppler effects. We therefore concentrate on the estimation of the complex gain, delay and Doppler offset of each tap of the multipath channel impulse response. We show that the frequency domain channel coefficients for an e…
This paper introduces a new two-dimensional modulation technique called Orthogonal Time Frequency Space (OTFS) modulation. OTFS has the novel and important feature of being designed in the delay-Doppler domain. When coupled with a suitable equalizer, OTFS modulation is able to exploit the full channel diversity over both time and frequency. Moreover, it converts the fading, time-varying wireless channel experienced by modulated signals such as OFDM into a time-independent channel with a complex channel gain that is essentially constant for all symbols. This design obviates the need for transmi…
