Driven by the explosive growth of Internet of Things (IoT) devices with stringent requirements on latency and reliability, ultra-reliability and low latency communication (uRLLC) has become one of the three key communication scenarios for the fifth generation (5G) and beyond 5G communication systems. In this paper, we focus on the beamforming design problem for the downlink multiuser uRLLC systems. Since the strict demand on the reliability and latency, in general, short packet transmission is a favorable form for uRLLC systems, which indicates the literature Shannon's capacity formula is no longer applicable. With the finite blocklength transmission, the achievable delivery rate is greatly influenced by the reliability and latency. Using the developed achievable delivery rate formula for finite blocklength transmission, we respectively formulate the problems of interest as the weighted sum rate maximization, energy efficiency maximization, and user fairness optimization by considering the maximum allowable transmission power and minimum rate requirement. It's worthy pointing out that this is the first work to design the beamforming vectors for the downlink multiuser uRLLC systems. To address these non-convex problems, some important insights have been discovered by analyzing the function of achievable delivery rate. For example, the minimum rate requirement can be realized by low bounded the signal-to-interference-plus-noise ratio. Based on the discovered results, we provide algorithms to optimize the beamforming vectors and power allocation, which are guaranteed to converge to a local optimum solution of the formulated problems with low computational complexity. Our simulation results reveal that our proposed beamforming algorithms outperform the zero-forcing beamforming algorithm with equal power allocation widely used in the existing literatures.
Wyner's soft-handoff network is considered where transmitters simultaneously send messages of enhanced mobile broadband (eMBB) and ultra-reliable low-latency communication (URLLC) services. Due to the low-latency requirements, the URLLC messages are transmitted over fewer channel uses compared to the eMBB messages. To improve the reliability of the URLLC transmissions, we propose a coding scheme with finite blocklength codewords that exploits dirty-paper coding (DPC) to precancel the interference from eMBB transmissions. Rigorous bounds are derived for the error probabilities of eMBB and URLLC…
The fast adoption of Massive MIMO for high-throughput communications was enabled by many research contributions mostly relying on infinite-blocklength information-theoretic bounds. This makes it hard to assess the suitability of Massive MIMO for ultra-reliable low-latency communications (URLLC) operating with short blocklength codes. This paper provides a rigorous framework for the characterization and numerical evaluation (using the saddlepoint approximation) of the error probability achievable in the uplink and downlink of Massive MIMO at finite blocklength. The framework encompasses imperfe…
In URLLC, short packet transmission is adopted to reduce latency, such that conventional Shannon's capacity formula is no longer applicable, and the achievable data rate in finite blocklength becomes a complex expression with respect to the decoding error probability and the blocklength. To provide URLLC service in a factory automation scenario, we consider that the central controller transmits different packets to a robot and an actuator, where the actuator is located far from the controller, and the robot can move between the controller and the actuator. In this scenario, we consider four fu…
In this paper, we employ a user-centric (UC) cell-free massive MIMO (CFmMIMO) network for providing ultra reliable low latency communication (URLLC) when traditional ground users (GUs) coexist with unmanned aerial vehicles (UAVs). We study power control in both the downlink and the uplink when partial zero-forcing (PZF) transmit/receive beamforming and maximum ratio transmission/combining are utilized. We consider optimization problems where the objective is to maximize either the users' sum URLLC rate or the minimum user's URLLC rate. The URLLC rate function is both complicated and nonconvex …
In this paper, a multi-objective optimization problem (MOOP) is proposed for maximizing the achievable finite blocklength (FBL) rate while minimizing the utilized channel blocklengths (CBLs) in a reconfigurable intelligent surface (RIS)-assisted short packet communication system. The formulated MOOP has two objective functions namely maximizing the total FBL rate with a target error probability, and minimizing the total utilized CBLs which is directly proportional to the transmission duration. The considered MOOP variables are the base station (BS) transmit power, number of CBLs, and passive b…
Ultra-reliable low latency communication (URLLC) is one of three primary use cases in the fifth-generation (5G) networks, and its research is still in its infancy due to its stringent and conflicting requirements in terms of extremely high reliability and low latency. To reduce latency, the channel blocklength for packet transmission is finite, which incurs transmission rate degradation and higher decoding error probability. In this case, conventional resource allocation based on Shannon capacity achieved with infinite blocklength codes is not optimal. Security is another critical issue in mis…
The non-orthogonal coexistence between the enhanced mobile broadband (eMBB) and the ultra-reliable low-latency communication (URLLC) in the downlink of a multi-cell massive MIMO system is rigorously analyzed in this work. We provide a unified information-theoretic framework blending an infinite-blocklength analysis of the eMBB spectral efficiency (SE) in the ergodic regime with a finite-blocklength analysis of the URLLC error probability relying on the use of mismatched decoding, and of the so-called saddlepoint approximation. Puncturing (PUNC) and superposition coding (SPC) are considered as …
How to provide information security while fulfilling ultra reliability and low-latency requirements is one of the major concerns for enabling the next generation of ultra-reliable and low-latency communications service (xURLLC), specially in machine-type communications. In this work, we investigate the reliability-security tradeoff via defining the leakage-failure probability, which is a metric that jointly characterizes both reliability and security performances for short-packet transmissions. We discover that the system performance can be enhanced by counter-intuitively allocating fewer reso…
Fraunhofer Institute for Telecommunications, Heinrich Hertz Institute (HHI)（弗劳恩霍夫电信研究所，海因里希·赫兹研究所（HHI））；Technical University Of Berlin（柏林工业大学）；NVIDIA（英伟达）
In this feasibility study, we have implemented a recently proposed partially linear multiuser detection algorithm in reproducing kernel Hilbert spaces (RKHSs) on a GPU-accelerated platform. Partially linear multiuser detection, which combines the robustness of linear detection with the power of nonlinear methods, has been proposed for a massive connectivity scenario with the non-orthogonal multiple access (NOMA). This is a promising approach, but detecting payloads within a received orthogonal frequency division multiplexing (OFDM) radio frame requires the execution of a large number of inner …
High-fidelity, real-time interactive applications are envisioned with the emergence of the Internet of Things (IoT) and tactile Internet by means of ultra-reliable low-latency communications (URLLC). Exploiting time diversity for fulfilling the URLLC requirements in an energy efficient manner is a challenging task due to the nontrivial interplay among packet size, retransmission rounds and delay, and transmit power. In this paper, we study the fundamental energy-latency tradeoff in URLLC systems employing incremental redundancy (IR) hybrid automatic repeat request (HARQ). We cast the average e…
In this work, we consider one-way ultra-reliable and low-latency communication (URLLC), where only the transmission in one direction requires URLLC and the transmission in the opposite direction does not. In order to meet the low-latency requirement of the one-way URLLC, we propose to use a truncated channel inversion power control (CIPC) to eliminate the requirement and the associated overhead of the training-based channel estimation at the receiver, while utilizing the multi-antenna technique at the transmitter to enhance the communication reliability. We first derive the transmission outage…
Ultra-reliable and low-latency communications (URLLC) have stringent requirements on quality-of-service and network availability. Due to path loss and shadowing, it is very challenging to guarantee the stringent requirements of URLLC with satisfactory communication range. In this paper, we first provide a quantitative definition of network availability in the short blocklength regime: the probability that the reliability and latency requirements can be satisfied when the blocklength of channel codes is short. Then, we establish a framework to maximize available range, defined as the maximal co…
In URLLC the performance of short message communications highly depends on the training sequence length due to the stringent latency and reliability requirements. In this paper, we study the performance of cooperative and non-cooperative transmissions under imperfect channel estimation and Rayleigh fading for URLLC. We assume a peak power constraint on pilot symbols in addition to the average power constraint which is used for comparison purposes. We obtain the optimal training length as a function of blocklength and power constraint factor to meet the URLLC requirements. Moreover, the simulat…
In this paper, we study resource allocation algorithm design for multiuser orthogonal frequency division multiple access (OFDMA) ultra-reliable low latency communication (URLLC) in mobile edge computing (MEC) systems. To achieve the stringent end-to-end delay and reliability requirements of URLLC MEC systems, we propose joint uplink-downlink resource allocation and finite blocklength transmission. Furthermore, we propose a partial time overlap between the uplink and downlink frames to minimize the end-to-end delay, which introduces new time causality constraints. Then, the proposed resource al…
Low-rate and short-packet transmissions are important for ultra-reliable low-latency communications (URLLC). In this paper, we put forth a new family of sparse superposition codes for URLLC, called block orthogonal sparse superposition (BOSS) codes. We first present a code construction method for the efficient encoding of BOSS codes. The key idea is to construct codewords by the superposition of the orthogonal columns of a dictionary matrix with a sequential bit mapping strategy. We also propose an approximate maximum a posteriori probability (MAP) decoder with two stages. The approximate MAP …
Fifth generation mobile communication systems (5G) have to accommodate both Ultra-Reliable Low-Latency Communication (URLLC) and enhanced Mobile Broadband (eMBB) services. While, eMBB applications support high data rates, URLLC services aim at guaranteeing low-latencies and high-reliabilities. eMBB and URLLC services are scheduled on the same frequency band, where the different latency requirements of the communications render the coexistence challenging. In this survey, we review, from an information theoretic perspective, coding schemes that simultaneously accommodate URLLC and eMBB transmis…
Ultra-reliable and low-latency communications (URLLC) is expected to be supported without compromising the resource usage efficiency. In this paper, we study how to maximize energy efficiency (EE) for URLLC under the stringent quality of service (QoS) requirement imposed on the end-to-end (E2E) delay and overall packet loss, where the E2E delay includes queueing delay and transmission delay, and the overall packet loss consists of queueing delay violation, transmission error with finite blocklength channel codes, and proactive packet dropping in deep fading. Transmit power, bandwidth and numbe…
In this paper, we investigate the effectiveness of the hybrid automatic repeat request (HARQ) technique in providing high-reliability and low-latency in the finite blocklength (FBL) regime in a single user uplink scenario. We characterize the packet error rate (PER), throughput, and delay performance of chase combining HARQ (CC-HARQ) and incremental redundancy HARQ (IR-HARQ) in AWGN and Rayleigh fading channel with $m$ retransmissions. Furthermore, we consider a quasi-static fading channel model, which is more accurate than the over-simplified i.i.d. block fading or same channel assumption ove…
The Fourth Industrial Revolution (Industrial 4.0) is coming, and this revolution will fundamentally enhance the way the factories manufacture products. The conventional wired lines connecting central controller to robots or actuators will be replaced by wireless communication networks due to its low cost of maintenance and high deployment flexibility. However, some critical industrial applications require ultra-high reliability and low latency communication (URLLC). In this paper, we advocate the adoption of massive multiple-input multiple output (MIMO) to support the wireless transmission for…
This paper considers the downlink of an ultra-reliable low-latency communication (URLLC) system in which a base station (BS) serves multiple single-antenna users in the short (finite) blocklength (FBL) regime with the assistance of a reconfigurable intelligent surface (RIS). In the FBL regime, the users' achievable rates are complex functions of the beamforming vectors and of the RIS's programmable reflecting elements (PREs). We propose the joint design of the transmit beamformers and PREs, the problem of maximizing the geometric mean (GM) of these rates (GM-rate) and show that this aforementi…
Stringent constraints on both reliability and latency must be guaranteed in ultra-reliable low-latency communication (URLLC). To fulfill these constraints with computationally constrained receivers, such as low-budget IoT receivers, optimal transmission parameters need to be studied in detail. In this paper, we introduce a multi-objective optimization framework for the optimal design of URLLC in the presence of decoding complexity constraints. We consider transmission of short-blocklength codewords that are encoded with linear block encoders, transmitted over a binary-input AWGN channel, and f…
In this paper, cooperative non-orthogonal multiple access (C-NOMA) is considered in short packet communications with finite blocklength (FBL) codes. The performance of a decode-and-forward (DF) relaying along with selection combining (SC) and maximum ratio combining (MRC) strategies at the receiver side is examined. We explore joint user pairing and resource allocation to maximize fair throughput in a downlink (DL) scenario. In each pair, the user with a stronger channel (strong user) acts as a relay for the other one (weak user), and optimal power and blocklength are allocated to achieve max-…
With the phenomenal growth of the Internet of Things (IoT), Ultra Reliable Low Latency Communications (URLLC) has potentially been the enabler to guarantee the stringent requirements on latency and reliability. However, how to achieve low latency and ultra-reliability with the random arrival remains open. In this paper, a queue-aware variable-length channel coding is presented over the single URLLC user link, in which the finite blocklength of channel coding is determined based on the random arrival. More particularly, a cross-layer approach is proposed for the URLLC user to establish the opti…
We use stochastic network calculus to investigate the delay performance of a multiuser MISO system with zero-forcing beamforming. First, we consider ideal assumptions with long codewords and perfect CSI at the transmitter, where we observe a strong channel hardening effect that results in very high reliability with respect to the maximum delay of the application. We then study the system under more realistic assumptions with imperfect CSI and finite blocklength channel coding. These effects lead to interference and to transmission errors, and we derive closed-form lower and upper bounds on the…
This paper studies an intelligent reflecting surface (IRS)-aided downlink ultra-reliable and low-latency communication (URLLC) system, in which an IRS is dedicatedly deployed to assist a base station (BS) to send individual short-packet messages to multiple users. To enhance the URLLC performance, the users are divided into different groups and the messages for users in each group are encoded into a single codeword. By considering the time division multiple access (TDMA) protocol among different groups, our objective is to minimize the total latency for all users subject to their individual re…
Polar codes have been gaining a lot of interest due to it being the first coding scheme to provably achieve the symmetric capacity of a binary memoryless channel with an explicit construction. However, the main drawback of polar codes is the low throughput of its successive cancellation (SC) decoding. Simplified SC decoding algorithms of polar codes can be used to reduce the latency of the polar decode by faster processing of specific sub-codes in the polar code. By combining simplified SC with a list decoding technique, such as SC list (SCL) decoding, polar codes can cater to the two conflict…
GNN-Based Polarforming for Multi-User MISO Short-Packet URLLC under Imperfect CSI
Pasargad Institute for Advanced Innovative Solutions (PIAIS)（帕萨加德先进创新解决方案研究所）；Department of Electrical Engineering, Sharif University of Technology（谢里夫理工大学电气工程系）；Department of Electrical Engineering, Amirkabir University of Technology（阿米尔卡比尔理工大学电气工程系）；Interdisciplinary Centre for Security, Reliability and Trust (SnT), University of Luxembourg（卢森堡大学安全、可靠性与信任跨学科中心）；Department of Electrical and Computer Engineering, University of Cyprus（塞浦路斯大学电气与计算机工程系）
In this paper, the average achievable rate of a re-configurable intelligent surface (RIS) aided factory automation is investigated in finite blocklength (FBL) regime. First, the composite channel containing the direct path plus the product of reflected paths through the RIS is characterized. Then, the distribution of the received signal-to-noise ratio (SNR) is matched to a Gamma random variable whose parameters depend on the total number of RIS elements as well as the channel pathloss. Next, by assuming FBL model, the achievable rate expression is identified and the corresponding average rate …
Smart factories need to support the simultaneous communication of multiple industrial Internet-of-Things (IIoT) devices with ultra-reliability and low-latency communication (URLLC). Meanwhile, short packet transmission for IIoT applications incurs performance loss compared to traditional long packet transmission for human-to-human communications. On the other hand, cell-free massive multiple-input and multiple-output (CF mMIMO) technology can provide uniform services for all devices by deploying distributed access points (APs). In this paper, we adopt CF mMIMO to support URLLC in a smart facto…
Intelligent reflecting surface (IRS) and device-to-device (D2D) communication are two promising technologies for improving transmission reliability between transceivers in communication systems. In this paper, we consider the design of reliable communication between the access point (AP) and actuators for a downlink multiuser multiple-input single-output (MISO) system in the industrial IoT (IIoT) scenario. We propose a two-stage protocol combining IRS with D2D communication so that all actuators can successfully receive the message from AP within a given delay. The superiority of the protocol …
This paper studies the coherent and non-coherent multiuser multiple-input multiple-output (MU-MIMO) uplink system in the finite blocklength regime. The i.i.d. Gaussian codebook is assumed for each user. To be more specific, the BS first uses two popular linear processing schemes to combine the signals transmitted from all users, namely, MRC and ZF. Following it, the matched maximum-likelihood (ML) and mismatched nearest-neighbour (NN) decoding metric for the coherent and non-coherent cases are respectively employed at the BS. Under these conditions, the refined third-order achievable coding ra…
