Rate-Splitting Multiple Access (RSMA), relying on multi-antenna Rate-Splitting (RS) techniques, has emerged as a powerful strategy for multi-user multi-antenna systems. In this paper, RSMA is introduced as a unified multiple access for multi-antenna radar-communication (RadCom) system, where the base station has a dual communication and radar capability to simultaneously communicate with downlink users and probe detection signals to azimuth angles of interests. Using RS, messages are split into common and private parts, then encoded into common and private streams before being precoded and transmitted. We design the message split and the precoders for this RadCom system such that the Weighted Sum Rate (WSR) is maximized and the transmit beampattern is approximated to the desired radar beampattern under an average transmit power constraint at each antenna. We then propose a framework based on Alternating Direction Method of Multipliers (ADMM) to solve the complicated non-convex optimization problem. Results highlight the benefits of RSMA to unify RadCom transmissions and to manage the interference among radar and communications, over the conventional Space-Division Multiple Access (SDMA) technique.
In colocated compressive sensing MIMO radar, the measurement matrix is specified by antenna placement. To guarantee an acceptable recovery performance, this measurement matrix should satisfy certain properties, e.g., a small coherence. Prior work in the literature often employs randomized placement algorithms which optimize the prior distribution of antenna locations. The performance of these algorithms is suboptimal, as they can be easily enhanced via expurgation. In this paper, we suggest an iterative antenna placement algorithm which determines the antenna locations deterministically. The p…
Dual-Functional Radar-Communication (DFRC) system is an essential and promising technique for beyond 5G. In this work, we propose a powerful and unified multi-antenna DFRC transmission framework, where an additional radar sequence is transmitted apart from communication streams to enhance radar beampattern matching capability, and Rate-Splitting Multiple Access (RSMA) is adopted to better manage the interference. RSMA relies on multi-antenna Rate-Splitting (RS) with Successive Interference Cancellation (SIC) receivers, and the split and encoding of messages into common and private streams. We …
In order to further exploit the potential of joint multi-antenna radar-communication (RadCom) system, we propose two transmission techniques respectively based on separated and shared antenna deployments. Both techniques are designed to maximize the weighted sum rate (WSR) and the probing power at target's location under average power constraints at the antennas such that the system can simultaneously communicate with downlink users and detect the target within the same frequency band. Based on a Weighted Minimized Mean Square Errors (WMMSE) method, the separated deployment transmission is des…
Dual-Functional Radar-Communication systems enhance the benefits of communications and radar sensing by jointly implementing these on the same hardware platform and using the common RF resources. An important and latest concern to be addressed in designing such Dual-Functional Radar-Communication systems is maximizing the energy-efficiency. In this paper, we consider a Dual-Functional Radar-Communication system performing simultaneous multi-user communications and radar sensing, and investigate the energy-efficiency behaviour with respect to active transmission elements. Specifically, we formu…
One of the trends that is gaining more and more importance in the field of beyond-5G and 6G wireless communication systems is the investigation on systems that jointly perform communication and sensing of the environment. This paper proposes to use a base station (BS), that we call \textit{radar-BS}, equipped with a large-scale antenna array to execute, using the same frequency range, communication with mobile users and sensing/surveillance of the surrounding environment through radar scanning. The massive antenna array can indeed both operate as a MIMO radar with co-located antennas -- transm…
In order to manage the increasing interference between radar and communication systems, joint radar and communication (RadCom) systems have attracted increased attention in recent years, with the studies so far considering the assumption of perfect Channel State Information at the Transmitter (CSIT). However, such an assumption is unrealistic and neglects the inevitable CSIT errors that need to be considered to fully exploit the multi-antenna processing and interference management capabilities of a joint RadCom system. In this work, a joint RadCom system is designed which marries the capabilit…
In this paper, a compact dual-polarized Vivaldi antenna is presented. Four Vivaldi elements are used as radiators, and are positioned obliquely and connected in a horn shape. By exciting two sets of elements, two orthogonally polarized radiations can be achieved. The dual-polarized antenna features a low operating frequency band with a wide bandwidth, high port isolation, good directional radiation performance, and a very compact size, making it highly suitable for the ground penetrating radar (GPR) application.
This paper considers human activity classification for an indoor radar system. Human motions generate nonstationary radar returns which represent Doppler and micro-Doppler signals. The time-frequency (TF) analysis of micro-Doppler signals can discern subtle variations on the motion by precisely revealing velocity components of various moving body parts. We consider radar for activity monitoring using TF-based machine learning approach exploiting both temporal and spatial degrees of freedom. The proposed approach captures different human motion representations more vividly in joint-variable dat…
Ultrawideband radar is an attractive technology for a variety of applications including security systems. As such, it is essential to develop low-cost systems that produce clear target images. Electromagnetic inverse scattering with time-reversal imaging has been studied for a variety of applications. The time-reversal method, however, uses large-scale antenna arrays, making the system potentially more costly. In this study, we propose an ultrawideband radar imaging algorithm, namely the stepped-frequency DORT algorithm, that uses multi-path scattering for a single antenna. The proposed imagin…
In this paper, we consider a multi-antenna dual-functional radar-communication (DFRC) satellite system, where the satellite has a dual capability to simultaneously communicate with downlink satellite users (SUs) and probe detection signals to a moving target. To design an appropriate DFRC waveform, we investigate the rate-splitting multiple access (RSMA)-assisted DFRC beamfoming, and employ the Cramer-Rao bound (CRB) as a radar performance metric, which represents a lower bound on the variance of unbiased estimators. The beamforming is optimized to minimize the CRB subject to quality of servic…
Spectrum congestion and competition over frequency bandwidth could be alleviated by deploying dual-function radar-communications systems, where the radar platform presents itself as a system of opportunity to secondary communication functions. In this paper, we propose a new technique for communication information embedding into the emission of multiple-input multiple-output (MIMO) radar using sparse antenna array configurations. The phases induced by antenna displacements in a sensor array are unique, which makes array configuration feasible for symbol embedding. We also exploit the fact that…
Controlling the radar beam-pattern by optimizing the transmit covariance matrix is a well-established approach for performance enhancement in multiple-input-multiple-output (MIMO) radars. In this paper, we investigate the joint optimization of the waveform covariance matrix and the antenna position vector for a MIMO radar system to approximate a given transmit beam-pattern, as well as to minimize the cross-correlation between the probing signals at a number of given target locations. We formulate this design task as a non-convex optimization problem and then propose a cyclic optimization appro…
Sinuous antennas exhibit many desirable properties for ground penetrating radar (GPR) applications such as ultra-wide bandwidth, polarization diversity, and a low-profile form factor. However, sinuous antennas are dispersive since the active region moves with frequency along the structure. This is an undesirable quality for pulsed-radar applications since the radiated pulse will be distorted. Such distortion may be detrimental to close-in sensing applications such as GPR. This distortion may be compensated in processing with accurately simulated or measured phase data. However, antenna perform…
Multiple input multiple output (MIMO) radar is known for its superiority over conventional radar due to its antenna and waveform diversity. Although higher angular resolution, improved parameter identifiability, and better target detection are achieved, the hardware costs (due to multiple transmitters and multiple receivers) and high energy consumption (multiple pulses) limit the usage of MIMO radars in large scale networks. On one hand, higher angle and velocity estimation accuracy is required, but on the other hand, a lower number of antennas/pulses is desirable. To achieve such a compromise…
Multiple-input multiple-output (MIMO) radar has several advantages with respect to the traditional radar array systems in terms of performance and flexibility. However, in order to achieve high angular resolution, a MIMO radar requires a large number of transmit and receive antennas, which increases hardware design and computational complexities. Although spatial compressive sensing (CS) has been recently considered for a pulsed-waveform MIMO radar with sparse random arrays, such methods for the frequency-modulated continuous wave (FMCW) radar remain largely unexplored. In this context, we pro…
Since the seminal paper by Marzetta from 2010, the Massive MIMO paradigm in communication systems has changed from being a theoretical scaled-up version of MIMO, with an infinite number of antennas, to a practical technology. Its key concepts have been adopted in the 5G new radio standard and base stations, where $64$ fully-digital transceivers have been commercially deployed. Motivated by these recent developments, this paper considers a co-located MIMO radar with $M_T$ transmitting and $M_R$ receiving antennas and explores the potential benefits of having a large number of virtual spatial an…
Dual-function radar communications (DFRC) systems have recently been proposed to enable the coexistence of radar and wireless communications, which in turn alleviates the increased spectrum congestion crisis. In this paper, we consider the problem of sparse transmit array design for DFRC systems by antenna selection where same or different antennas are assigned to different functions. We consider three different types of DFRC systems which implement different simultaneous beamformers associated with single and different sparse arrays with shared aperture. We utilize the array configuration as …
This paper presents an experimental study to evaluate the effects of antenna radiation parameters on the detection capabilities of a 2.4 GHz Doppler radar used in non-contact heart rate monitoring systems. Four different types of patch antennas and array configurations were implemented on both the transmitter and receiver sides. Extensive experiments using a linear actuator were performed and several interesting and nontrivial results were reported. It is shown that using a linearly polarized single patch antenna at the transmitter and a circularly polarized antenna array at the receiver resul…
We propose two concepts for the significant improvement of surface current mapping with bistatic oceanographic High-Frequency Radars. These ameliorations pertain to the azimuthal processing of radar data with linear or quasi-linear antenna arrays. The first idea is to take advantage of the remote transmitter to perform an automatic correction of the complex gains of the receiving antennas based on the analysis of the signal received in the direct path. This direct signal can be found at the zero-Doppler and minimal range cell in the Range-Doppler representation. We term this adjustment as "sel…
Direction of arrival (DoA) estimation of targets improves with the number of elements employed by a phased array radar antenna. Since larger arrays have high associated cost, area and computational load, there is recent interest in thinning the antenna arrays without loss of far-field DoA accuracy. In this context, a cognitive radar may deploy a full array and then select an optimal subarray to transmit and receive the signals in response to changes in the target environment. Prior works have used optimization and greedy search methods to pick the best subarrays cognitively. In this paper, we …
Multistatic radar system (MSRS) is considered an effective scheme to suppress mainlobe jamming, since it has higher spatial resolution enabling jamming cancellation from spatial domain. To develop electronic countermeasures against MSRS, a random array subset selection (RASS)jamming method is proposed in this paper. In the RASS jammer, elements of the array antenna are activated randomly, leading to stable mainlobe and random sidelobes, different from the traditional jammer that applies the complete antenna array enjoying constant mainlobe and sidelobes. We study the covariance matrix of jammi…
In this paper, we investigate the problem of jointly optimizing the waveform covariance matrix and the antenna position vector for multiple-input-multiple-output (MIMO) radar systems to approximate a desired transmit beampattern as well as to minimize the cross-correlation of the received signals reflected back from the targets. We formulate the problem as a non-convex program and then propose a cyclic optimization approach to efficiently tackle the problem. We further propose a novel local optimization framework in order to efficiently design the corresponding antenna positions. Our numerical…
This paper investigates RF-based system for automatic American Sign Language (ASL) recognition. We consider radar for ASL by joint spatio-temporal preprocessing of radar returns using time frequency (TF) analysis and high-resolution receive beamforming. The additional degrees of freedom offered by joint temporal and spatial processing using a multiple antenna sensor can help to recognize ASL conversation between two or more individuals. This is performed by applying beamforming to collect spatial images in an attempt to resolve individuals communicating at the same time through hand and arm mo…
A novel dual-function radar communication (DFRC) system is proposed, that achieves high target resolution and high communication rate. It consists of a multiple-input multiple-output (MIMO) radar, where only a small number of antennas are active in each channel use. The probing waveforms are orthogonal frequency division multiplexing (OFDM) type. The OFDM carriers are divided into two groups, one that is used by the active antennas in a shared fashion, and another one, where each subcarrier is assigned to an active antenna in an exclusive fashion (private subcarriers). Target estimation is car…
In this paper, we introduce a novel algorithm that can dramatically reduce the number of antenna elements needed to accurately predict the direction of arrival (DOA) for multiple input multiple output (MIMO) radar. The new proposed algorithm predicts the received signal of a large antenna setup using reduced number of antenna by using coupled dictionary learning. Hence, this enables the MIMO radar to resolve more paths, which could not be resolved by the fewer antennas. Specifically, we overcome the problem of inaccurate DOA estimation due to a small virtual array setup. For example, we can us…
In the phased-array radar (PAR) signals from each antenna are transmitted at the same carrier frequency, which yields narrowly focused only angle dependent beampattern. In contrast, in the frequency-diverse-array (FDA) radar signals from antenna array are generally transmitted at linearly increasing frequencies that yields range, time, and angle dependent beampattern. Reported literature on FDA radar missed the contribution of path-differences in the signal model due to the antenna array elements, which may lead to misleading results. In this work, incorporating missed path-differences, the si…
Institute of Digital Communication Systems, Ruhr University Bochum（鲁尔大学波鸿数字通信系统研究所）；Department of Electrical and Computer Engineering, Purdue University（普渡大学电气与计算机工程系）
We present a MUSIC-based Direction of Arrival (DOA) estimation strategy using small antenna arrays, via employing deep learning for reconstructing the signals of a virtual large antenna array. Not only does the proposed strategy deliver significantly better performance than simply plugging the incoming signals into MUSIC, but surprisingly, the performance is also better than directly using an actual large antenna array with MUSIC for high angle ranges and low test SNR values. We further analyze the best choice for the training SNR as a function of the test SNR, and observe dramatic changes in …
MIMO transmit arrays allow for flexible design of the transmit beampattern. However, the large number of elements required to achieve certain performance using uniform linear arrays (ULA) maybe be too costly. This motivated the need for thinned arrays by appropriately selecting a small number of elements so that the full array beampattern is preserved. In this paper, we propose Learn-to-Select (L2S), a novel machine learning model for selecting antennas from a dense ULA employing a combination of multiple Softmax layers constrained by an orthogonalization criterion. The proposed approach can b…
A fully-digital wideband joint communication-radar (JCR) with a multiple-input-multiple-output (MIMO) architecture at the millimeter-wave (mmWave) band will enable high joint communication and radar performance with enhanced design flexibility. A quantized receiver with few-bit analog-to-digital converters (ADCs) will enable a practical JCR solution with reduced power consumption for futuristic portable devices and autonomous vehicles. In this paper, we present a joint communication-radar proof-of-concept platform, named JCR70, to evaluate and demonstrate the performance of these JCR systems u…
This paper considers the uplink of a massive MIMO communication system using 5G New Radio-compliant multiple access, which is to co-exist with a radar system using the same frequency band. A system model taking into account the reverberation (clutter) produced by the radar system onto the massive MIMO receiver is proposed. In this scenario, several receivers for uplink channel estimation and data detection are proposed, ranging from the simple channel-matched beamformer to the zero-forcing and linear minimum mean square error receivers for clutter disturbance rejection, under the two opposite …
In this paper, we introduce the design of a multi-antenna Joint Radar-Communication (JRC) system with Rate Splitting Multiple Access (RSMA) and low resolution Digital-to-Analog Converter (DAC) units. Using RSMA, the communication messages are split into private and common parts, then precoded and quantized before transmission. We use a problem formulation to design the JRC system with RSMA and low resolution DACs by maximizing communication sum-rate and the proximity of the resulting JRC waveform to an optimal radar beampattern under an average transmit power constraint. We solve the joint sum…
With the use of common signaling methods for dual-function radar-communications (DFRC) systems, the susceptibility of eavesdropping on messages aimed at legitimate users has worsened. For DFRC systems, the radar target may act as an eavesdropper (ED) that receives a high-energy signal thereby leading to additional challenges. Unlike prior works, we consider a multicast multi-antenna DFRC system with multiple EDs. We then propose a physical layer design approach to maximize the secrecy rate by installing intelligent reflecting surfaces in the radar channels. Our optimization of multiple ED mult…
Dual-function radar-communications (DFRC) systems implement radar and communication functionalities on a single platform. Jointly designing these subsystems can lead to substantial gains in performance as well as size, cost, and power consumption. In this paper, we propose a DFRC system, which utilizes generalized spatial modulation (GSM) to realize coexisting radar and communications waveforms. Our proposed GSM-based scheme, referred to as spatial modulation based communication-radar (SpaCoR) system, allocates antenna elements among the subsystems based on the transmitted message, thus achiev…
Wideband Antenna Deconvolution for Bistatic Millimeter Wave Radar Reflectivity Measurements
Thuringian Center of Innovation in Mobility（图林根创新 mobility 中心）；Institute of Information Technology, Technische Universität Ilmenau（伊尔梅瑙工业大学信息技术研究所）；RF and Microwave Research Group, Technische Universität Ilmenau（伊尔梅瑙工业大学射频与微波研究组）
Imperfect Channel State Information at the Transmitter (CSIT) is inevitable in modern wireless communication networks, and results in severe multi-user interference in multi-antenna Broadcast Channel (BC). While the capacity of the multi-antenna (Gaussian) BC with perfect CSIT is known and achieved by Dirty Paper Coding (DPC), the capacity and the capacity-achieving strategy of the multi-antenna BC with imperfect CSIT remain unknown. Conventional approaches therefore rely on applying communication strategies designed for perfect CSIT to the imperfect CSIT setting. In this work, we break this c…
