Defect centers are promising candidates for waveguide-integrated silicon light sources. We demonstrate microresonator- and waveguide-coupled photoluminescence from silicon W~centers. Microphotoluminescence measurements indicate wavelengths on-resonance with resonator modes are preferentially coupled to an adjacent waveguide. Quality factors of at least 5,300 are measured, and free spectral ranges closely match expectation. The W~center phonon sideband can be used as a spectral diagnostic for a broader range waveguide-based devices on cryogenic silicon photonic platforms.
We report on coupling between semiconducting single-wall carbon nanotubes (s-SWNT) photoluminescence and silicon microring resonators. Polyfluorene extracted s-SWNT deposited on such resonators exhibit sharp emission peaks, due to interaction with the cavity modes of the microring resonators. Ring resonators with radius of 5 μm and 10 μm were used, reaching quality factors up to 4000 in emission. These are among the highest values reported for carbon nanotubes coupled with an integrated cavity on silicon platform, which open up the possibility to build s-SWNT based efficient light source on si…
In this paper, a new design of optical delay line based on coupled ring resonators in photonic crystals is proposed and analyzed by means of numerical simulation in CST Microwave Studio. The performance of the proposed photonic crystal ring resonator (PhCRR) based coupled resonant optical waveguide (CROW) is compared to: point-defect cavity based coupled cavity waveguides (CCW) in photonic crystal. microring resonator (MRR) based CROW. The suggested design addresses compactness issues of the MRR CROW while offering normalized delay values better than CCW and comparable to MRR CROW. The PhCRR C…
We report a tunable optical filter based on phase change material $Ge_{2}Sb_{2}Te_{5}$ embedded in a silicon microring resonator. The high thermo-optic coefficient of $Ge_{2}Sb_{2}Te_{5}$ in amorphous phase enables tuning of resonance wavelength in broad range with a very small active volume. The low-loss indium-tin-oxide electrodes are employed to induce Joule heating in $Ge_{2}Sb_{2}Te_{5}$-Si active waveguide region. The electrically induced heating in the active region alters the effective refractive index of hybrid microring resulting in a wavelength tuning of 1.04 nm for an applied volta…
Microring resonators are critical photonic components used in filtering, sensing and nonlinear applications. To date, the development of high performance microring resonators in LNOI has been limited by the sidewall angle, roughness and etch depth of fabricated rib waveguides. We present large free spectral range microring resonators patterned via electron beam lithography in high-index contrast $Z$-cut LNOI. Our microring resonators achieve an FSR greater than 5 nm for ring radius of 30 $μ$m and a large 3 dB resonance bandwidth. We demonstrate 3 pm/V electro-optic tuning of a 70 $μ$m-radius r…
The wavelength selective linear absorption in communication C-band is investigated in CMOS-processed PECVD silicon nitride rings. In the overcoupled region, the linear absorption loss lowers the on-resonance transmission of a ring resonator and increases its overall quality factor. Both the linear absorption and ring quality factor are maximized near 1520 nm. The direct heating by phonon absorption leads to thermal optical bistable switching in PECVD silicon nitride based microring resonators. We calibrate the linear absorption rate in the microring resonator by measuring its transmission line…
Development of low-loss photonic components in the ultraviolet (UV) band will open new prospects for classical and quantum optics. Compared with other integrated platforms, aluminum nitride (AlN) is particularly attractive as it features an enormous bandgap of ~6.2 eV and intrinsic chi(2) and chi(3) susceptibilities. In this work, we demonstrate a record quality factor of 2.1 x 105 (optical loss ~ 8 dB/cm) at 390 nm based on single-crystalline AlN microrings. The low-loss AlN UV waveguide represents a significant milestone toward UV photonic integrated circuits as it features full compatibilit…
We report on four-wave mixing in a silicon microring resonator using a self-pumping scheme instead of an external laser. The ring resonator is inserted in an external-loop cavity with a fibered semiconductor amplifier as a source of gain. The silicon microring acts as a filter and we observe lasing in one of the microring's resonances. We study correlations between signal and idler generated beams using a Joint Spectral Density experiment.
The intensity buildup of light inside a lossy microring resonator can be used to enhance the generation of squeezed states via spontaneous parametric downconversion (SPDC). In this work, we model the generation of squeezed light in a microring resonator that is pumped with a Gaussian pulse via a side-coupled channel waveguide. We theoretically determine the optimum pump pulse duration and ring-to-channel coupling constant to minimize the quadrature noise (maximize the squeezing) in the ring for a fixed input pump energy. We derive approximate analytic expressions for the optimal coupling and p…
We demonstrate that linear absorption coefficient (LAC) of a graphene-silicon hybrid waveguide (GSHW) is determined by the optical transmission spectra of a graphene coated symmetrically coupled add-drop silicon microring resonator (SC-ADSMR), of which the value is around 0.23 dB/um. In contrast to the traditional cut-back method, the measured results are not dependent on the coupling efficiency of the fiber tip and the waveguide. Moreover, precision evaluation of graphene coated silicon microring resonator (SMR) is crucial for the optoelectronic devices targeting for compact footprint and low…
A new category of optical microring resonator, which is analogous to the Möbius strip, is proposed. The "Möbius" microring resonator allows the conversion between modes with different polarizations in the ring and light must circulate two cycles to be converted back to the original polarization status, which is similar to a Möbius strip. This topology structure of polarization leads to the free spectral range be half of that corresponds to the cavity round trip. The eigenmodes of this microring are hybridizations of different polarizations and the breaking of the rotation invariance of the rin…
Atomically thin 2D materials provide a wide range of basic building blocks with unique properties, making them ideal for heterogeneous integration with a mature chip platform. An understanding the role of excitons in transition metal dichalcogenides in Silicon photonic platform is a prerequisite for advances in optical communication technology, signal processing, and possibly computing. Here we demonstrate passive tunable coupling by integrating few layers of MoTe2 on a micro-ring resonator. We find a TMD-to-rings circumference coverage length ratio to place the ring into critical coupling to …
We demonstrate an ultralow loss monolithic integrated lithium niobate photonic platform consisting of dry-etched subwavelength waveguides. We show microring resonators with a quality factor of 10$^7$ and waveguides with propagation loss as low as 2.7 dB/m.
We analyze fast and slow light transmission in a zig-zag microring resonator chain. This novel device permits the operation in both regimes. In the superluminal case, a new ubiquitous light transmission effect is found whereby the input optical pulse is reproduced in an almost simultaneous manner at the various system outputs. When the input carrier is tuned to a different frequency, the system permits to slow down the propagating optical signal. Between these two extreme cases, the relative delay can be tuned within a broad range.
We demonstrate experimentally that stable single longitudinal mode operation can be readily achieved in PT-symmetric arrangements of coupled microring resonators. Whereas any active resonator is in principle capable of displaying single-wavelength operation, selective breaking of PT-symmetry can be utilized to systematically enhance the maximum achievable gain of this mode, even if a large number of competing longitudinal or transverse resonator modes fall within the amplification bandwidth of the inhomogeneously broadened active medium. This concept is robust with respect to fabrication toler…
Here we show a photonic design for tunable dual-wavelength generation deploying optical nonlinear mode coupling of two coupled III-V semiconductor microring resonators (MRRs) connected to a pump and drop waveguide buses. Here one of the two rings contains a grating, while the other has a planar surface. The underling mechanism for the dual wavelength generation originates from the resonance-detuning of the spectra resulting in non-linear mode mixing. Tunability of the wavelengths is achieved by altering the grating depth of the MRR and the power coupling coefficients. For the grating design of…
The influence of Raman scattering and higher order dispersions on solitons and frequency comb generation in silica microring resonators is investigated. The Raman effect introduces a threshold value in the resonator quality factor above which the frequency locked solitons can not exist and, instead, a rich dynamics characterized by generation of self-frequency shift- ing solitons and dispersive waves is observed. A mechanism of broadening of the Cherenkov radiation through Hopf instability of the frequency locked solitons is also reported.
We report a high-responsive hot-electron photodetector based on the integration of an Au-MoS$_2$ junction with a silicon nitride microring resonator (MRR) for detecting telecom-band light. The coupling of the evanescent field of the silicon nitride MRR with the Au-MoS$_2$ Schottky junction region enhances the hot-electron injection efficiency. The device exhibits a high responsivity of 154.6 mA W-1 at the wavelength of 1516 nm, and the moderately uniform responsivities are obtained over the wavelength range of 1500 nm-1630 nm. This MRR-enhanced MoS2 hot-electron photodetector offers possibilit…
Microring resonators, as a fundamental building block of photonic integrated circuits, have been well developed into numerous functional devices, whose performances are strongly determined by microring's resonance lineshapes. We propose a compact structure to reliably realize Lorentzian, Fano, and electromagnetically induced transparency (EIT) resonance lineshapes in a microring. By simply inserting two air-holes in the side-coupled waveguide of a microring, a Fabry-Perot (FP) resonance is involved to couple with microring's resonant modes, showing Lorentzian, Fano, and EIT lineshapes over one…
In order to overcome the challenge of obtaining high modulation depth due to weak graphene-light interaction, a graphene-on-silicon nitride (SiNx) microring resonator based on graphene's gate-tunable optical conductivity is proposed and studied. Geometrical parameters of graphene-on-SiNx waveguide are systematically analyzed and optimized, yielding a loss tunability of 0.04 dB/μm and an effective index variation of 0.0022. We explicitly study the interaction between graphene and a 40-μm-radius microring resonator, where electro-absorptive and electro-refractive modulation are both taken into a…
Aluminum nitride has been shown to possess both strong Kerr nonlinearity and electro-optic Pockels effect. By combining these two effects, here we demonstrate on-chip reversible on/off switching of the optical frequency comb generated by an aluminum nitride microring resonator. We optimize the design of gating electrodes and the underneath resonator structure to effectively apply electric field without increasing the optical loss. The switching of the comb is monitored by measuring one of the frequency comb peaks while varying the electric field. The controlled comb electro-optic response is i…
We discuss the analytical temporal response of a microring resonator excited through a bus waveguide by an optical rectangular pulse. Finite difference time domain (FDTD) simulations illustrate the analytical solution and help in understanding the meaning of the different coupling regimes. In addition, we show that the temporal dynamics allows determing the coupling regime while the commonly used spectral characterization in the stationary regime does not. We also take advantage of the simulation to highlight the phase shift between the input and the output signals in the different coupling re…
We theoretically investigate and optimize the performance of four-wave mixing (FWM) in microring resonators (MRRs) integrated with two-dimensional (2D) layered graphene oxide (GO) films. Owing to the interaction between the MRRs and the highly nonlinear GO films as well as to the resonant enhancement effect, the FWM efficiency in GO-coated MRRs can be significantly improved. Based on previous experiments, we perform detailed analysis for the influence of the GO film parameters and MRR coupling strength on the FWM conversion efficiency (CE) of the hybrid MRRs. By optimizing the device parameter…
An array of ring resonators specifically designed can perform as a topological insulator. We conduct simulations using both Tight-Binding Model (TBM) and Transfer Matrix Method (TMM) to analyze the transport properties of such optical structure, verifying the presence of robust topological edge states which is immune to disorder and defect. We have also made a comparison between these two methods, of which results suggesting that TBM is only applicable under weakly-coupling condition while TMM is more rigorous. Finally we compared the structure with common microring array and coupled resonator…
Single mode lasing is experimentally demonstrated in a transversely multi-moded InP-based semiconductor microring arrangement. In this system, mode discrimination is attained by judiciously utilizing the exceptional points in a parity-time (PT) symmetric double microring configuration. The proposed scheme is versatile, robust to small fabrication errors, and enables the device to operate in a stable manner considerably above threshold while maintaining spatial and spectral purity. The results presented here pave the way towards a new class of chip-scale semiconductor lasers that utilize gain/l…
Two microring resonators, one with gain and one with loss, coupled to each other and to a bus waveguide, create an effective non-Hermitian potential for light propagating in the waveguide. Due to geometry, coupling for each microring resonator yields two counter-propagating modes with equal frequencies. We show that such a system enables implementation of many types of scattering peculiarities, which are either the second or fourth order. The spectral singularities separate parameter regions where the spectrum is either pure real or else comprises complex eigenvalues; hence, they represent the…
We utilize cross-phase modulation to observe all-optical switching in microring resonators fabricated with hydrogenated amorphous silicon (a-Si:H). Using 2.7-ps pulses from a mode-locked fiber laser in the telecom C-band, we observe optical switching of a cw telecom-band probe with full-width at half-maximum switching times of 14.8 ps, using approximately 720 fJ of energy deposited in the microring. In comparison with telecom-band optical switching in undoped crystalline silicon microrings, a-Si:H exhibits substantially higher switching speeds due to reduced impact of free-carrier processes.
We report a circuit cavity optomechanical system in which a nanomechanical resonator is adiabatically embedded inside an optical ring resonator with ultralow transition loss. The nanomechanical device forms part of the top layer of a horizontal silicon slot ring resonator, which enables dispersive coupling to the dielectric substrate via a tapered nanogap. Our measurements show nearly uncompromised optical quality factors (Q) after the release of the mechanical beam.
Thin-film lithium niobate is an attractive integrated photonics platform due to its low optical loss and favorable optical nonlinear and electro-optic properties. However, in applications such as second harmonic generation, frequency comb generation, and microwave-to-optics conversion, the device performance is strongly impeded by the photorefractive effect inherent in thin-films. In this paper, we show that the dielectric cladding on lithium niobate microring resonator has a significant influence on the photorefractive effect. By removing the dielectric cladding layer, the photorefractive eff…
We describe a new approach for on-chip optical non-reciprocity which makes use of strong optomechanical interaction in microring resonators. By optically pumping the ring resonator in one direction, the optomechanical coupling is only enhanced in that direction, and consequently, the system exhibits a non-reciprocal response. For different configurations, this system can function either as an optical isolator or a coherent non-reciprocal phase shifter. We show that the operation of such a device on the level of single-photon could be achieved with existing technology.
We report single plasmon generation with a self-assembled InAs/GaAs quantum dot embedded in a plasmonic microring resonator. The plasmonic cavity based on a GaAs microring is defined on an atomically-smooth silver surface. We fabricated this structure with the help of transfer printing, which enables the pick-and-place assembly of the complicated, heterogeneous three dimensional stack. We show that a high-order surface-plasmon-polariton transverse mode mediates efficient coupling between the InAs/GaAs quantum dots and the plasmonic cavity, paving the way for developing plasmonic quantum light …
We develop a general Hamiltonian treatement of spontaneous four-wave mixing in a microring resonator side-coupled to a channel waveguide. The effect of scattering losses in the ring is included, as well as parasitic nonlinear effects including self- and cross-phase modulation. A procedure for computing the output of such a system for arbitrary parameters and pump states is presented. For the limit of weak pumping an expression for the joint spectral intensity of generated photon pairs, as well as the singles-to-coincidences ratio, is derived.
Stimulated Brillouin scattering (SBS) has been demonstrated in silicon waveguides in recent years. However, due to the weak interaction between photons and acoustic phonons in these waveguides, long interaction length is typically necessary. Here, we experimentally show that forward stimulated Brillouin scattering in a short interaction length of a 20 um radius silicon microring resonator could give 1.2 dB peak gain at only 10mW coupled pump power. The experimental results demonstrate that both optical and acoustic modes can have efficient interaction in a short interaction length. The observe…
We propose and analyze an on-chip all-optical dynamical tuning scheme for coupled nonlinear resonators employing a single control beam injected in parallel with a signal beam. We show that nonlinear Kerr response can be used to dynamically switch the spectral properties between "dark-state" and electromagnetically-induced transparency configurations. Such scheme can be realized in integrated optical applications for pulse trapping and delaying.
Microring resonators made from silicon are becoming a popular microscale device format for generating photon pairs at telecommunications wavelengths at room temperature. In compact devices with a footprint less than $5\times 10^{-4}$ mm$^2$, we demonstrate pair generation using only a few microwatts of average pump power. We discuss the role played by important parameters such as the loss, group-velocity dispersion and the ring-waveguide coupling coefficient in finding the optimum operating point for silicon microring pair generation. Silicon photonics can be fabricated using deep ultraviolet …
We generate photon pairs in a-Si:H microrings using a CW pump, and find the Kerr coefficient of a-Si:H to be $3.73 \pm 0.25 \times 10^{-17}m^2/W$. By measuring the Q factor with coupled power we find that the loss in the a-Si:H micro-rings scales linearly with power, and therefore cannot originate from two photon absorption. Theoretically comparing a-Si:H and c-Si micro-ring pair sources, we show that the high Kerr coefficient of this sample of a-Si:H is best utilized for microrings with Q factors below $10^3$, but that for higher Q factor devices the photon pair rate is greatly suppressed due…
A path within the parameter space of detuning and pump power is demonstrated in order to obtain a single cavity soliton (CS) with certainty in SiN microring resonators in the anomalous dispersion regime. Once the single CS state is reached, it is possible to continue a path to compress it, broadening the corresponding single free spectral range (FSR) Kerr frequency comb. The first step to achieve this goal is to identify the stable regions in the parameter space via numerical simulations of the Lugiato-Lefever equation (LLE). Later, using this identification, we define a path from the stable m…
We demonstrate voltage-tunable thermo-optic bi- and tri-stability in silicon photonic microring resonators with lateral p-i-n junctions and present a technique for characterizing the thermo-optic transient response of integrated optical resonators. Our method for thermo-optic transient response measurement is applicable to any integrated photonics platform and uses standard equipment. Thermo-optic relaxation in encapsulated waveguides is found to be approximately logarithmic in time, consistent with the analytic solution for 2D heat diffusion. We develop a model for thermo-optic microring mult…
We demonstrate lasing in arrays of microring resonators with underlying para-Fermi symmetry. The properties of the algebra allow the analytic prediction of propagation constants and normal modes of an array of passive resonators that show the optical analogue of a zero-energy mode that is its own chiral pair. The rest of the normal modes in the linear model form chiral pairs that are evenly distributed around the pseudo zero-energy mode. We use this information to construct a class-B laser model where even and odd sites are driven with different strength in a pattern following para-Fermi algeb…
On-chip frequency comb generations enable compact broadband sources for spectroscopic sensing and precision spectroscopy. Recent microcomb studies focus on infrared spectral regime and have difficulty in accessing visible regime. Here, we demonstrate comb-like visible frequency line generation through second, third harmonic, and sum frequency conversion of a Kerr comb within a high Q aluminum nitride microring resonator pumped by a single telecom laser. The strong power enhancement, in conjunction with the unique combination of Pockels and Kerr optical nonlinearity of aluminum nitride, leads t…
Optical microresonators have recently attracted a growing attention in the photonics community. Their applications range from quantum electro-dynamics to sensors and filtering devices for optical telecommunication systems, where they are likely to become an essential building block. The integration of nonlinear and electro-optical properties in the resonators represents a very stimulating challenge, as it would incorporate new and more advanced functionality. Lithium niobate is an excellent candidate material, being an established choice for electro-optic and nonlinear optical applications. He…
We demonstrate an all-optical four-channel wavelength multicasting in a coupled Silicon microring resonator system. The scheme is based on two-photon absorption induced free carrier dispersion in Silicon. The coupled cavity facilitates resonance splitting that is utilized as individual channels for multicasting. Using the split resonances, we achieve an aggregate multicasted data rate of 48 Gbps (4X12 Gbps). Moreover, we also present a detailed analysis and performance of the multicasting architecture.
Graphene opens up for novel optoelectronic applications thanks to its high carrier mobility, ultra-large absorption bandwidth, and extremely fast material response. In particular, the opportunity to control optoelectronic properties through tuning of Fermi level enables electro-optical modulation, optical-optical switching, and other optoelectronics applications. However, achieving a high modulation depth remains a challenge because of the modest graphene-light interaction in the graphene-silicon devices, typically, utilizing only a monolayer or few layers of graphene. Here, we comprehensively…
We describe the design and fabrication of a scalable atom-light photonic interface based on a silicon nitride microring resonator on a transparent silicon dioxide-nitride multi-layer membrane. This new photonic platform is fully compatible with freespace cold atom laser cooling, stable trapping, and sorting at around $100~$nm from the microring surface, permitting the formation of an organized, strongly interacting atom-photonic hybrid lattice. We demonstrate small radius ($R\sim$16$μ$m) microring and racetrack resonators with a high quality factor $Q=3.2\times 10^5$, projecting a single atom …
Light trapping and radiation process from linear reciprocal photonic resonators is one of the fundamental processes in optical science and engineering. Recently, the concept of coherent virtual absorption (CVA) of light was introduced and investigated for planar and cylindrical optical structures. The key feature of CVA is that by engineering the time-dependence of the excitation waveform, one can temporarily store all the input energy into the optical structure without any leakage. Here we further explore this novel concept in integrated photonic setups made of microring resonators. By using …
