The present investigation provides the first field characterization of the influence of turbulent inflow on the blade structural response of a utility-scale wind turbine (2.5MW), using the unique facility available at the Eolos Wind Energy Research Station of the University of Minnesota. A representative one-hour dataset under a stable atmosphere is selected for the characterization, including the inflow turbulent data measured from the meteorological tower, high-resolution blade strain measurement at different circumferential and radiation positions along the blade, and the wind turbine operational conditions. The results indicate that the turbulent inflow modulates the turbine blade structural response in three representative frequency ranges: a lower frequency range (corresponding to modulations due to large eddies in the atmosphere), a higher frequency range (corresponding to flow structures in scales smaller than the rotor diameter), and an intermediate-range in between. The blade structure responds strongly to the turbulent inflow in the lower and intermediate ranges, while it is primarily dominated by the rotation effect and other high-frequency characteristics of wind turbines in the higher frequency range. Moreover, the blade structural behaviors at different azimuth angles, circumferential and radial locations along the blade are also compared, suggesting the comparatively high possibility of structural failure at certain positions. Further, the present study also uncovers the linkage between the turbulent inflow and blade structural response using temporal correlation. The derived findings provide insights into the development of advanced control strategies or blade design to mitigate the structural impact and increase blade longevity for the safer and more efficient operation of large-scale wind turbines.
Bioinspired flexible blades have been recently shown to significantly improve the versatility of horizontal-axis wind turbines, by widening their working range and increasing their efficiency. The aerodynamic and centrifugal forces bend the blade along its chord, varying the pitch angle by means of non-consuming mechanisms. Here we introduce a general method based on a universal scaling, which finds the optimal soft materials for the blades to maximize the overall turbine efficiency or rotational power, for any required geometry of classical horizontal-axis turbines. The optimization problem, …
CFD studies have been performed to demonstrate the effects of rotation on large wind turbine blades. The 10 MW blade of the Advanced Aerodynamic Tools for Large Rotors (AVATAR) project was selected in the present investigation. In order to demonstrate the rotational augmentation, lift coefficients of the blade sections were compared with the two-dimensional simulations at consistent inflow conditions. The increase of the lift coefficient was observed at the inboard section of the blade, showing the effect of rotation. A significant delay of separation point as well as a massive reduction of th…
Endwall and leading-edge film cooling of turbine blades in a hydrogen-fueled rotating detonation combustor-turbine coupled system
Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences（中国科学院宁波材料技术与工程研究所）；University of Chinese Academy of Sciences（中国科学院大学）；Institute for Energy Research, Jiangsu University（江苏大学能源研究所）
Monitoring the flow features over wind turbine blades is a challenging task that has become more and more crucial. This paper is devoted to demonstrate the ability of the e-TellTale sensor to detect the flow separation/reattachment dynamics over wind turbine blades. This sensor is made of a strip with a strain gauge sensor at its base. The velocity field was acquired using TR- PIV measurements over an oscillating thick blade section equipped with an e-TellTale sensor. PIV images were post-processed to detect movements of the strip, which was compared to movements of flow. Results show good agr…
The Darrieus vertical axis wind turbines (VAWTs) are one of the mainstream devices for wind energy utilization in the urban areas. The market's pursuit of high wind energy conversion efficiency promotes the research on improving the wind turbine power coefficient while reducing noise. This paper makes further investigation on the aerodynamics and aeroacoustics of a small VAWT with V-shaped blades and trailing-edge serrations. The feasibility of utilizing the Reynolds-Averaged Navier-Stokes SST k-omega turbulence model and the FW-H method is verified against experiments. The studied V-shaped bl…
We present a method to adapt Greenberg's potential flow model for coupled pitching and surging flow such that it can be applied to predict the loads on a vertical-axis wind turbine blade. The model is extended to compute loads on a blade undergoing multi-harmonic oscillations in effective angle of attack and incoming flow velocity by formulating the blade kinematics as a sum of simple harmonic motions. Each of these functions is a multiple of the main turbine rotational frequency, associated with an individual amplitude, as suggested by Greenberg. The results of the adapted model are compared …
A method for inverse design of horizontal axis wind turbines (HAWTs) is presented in this paper. The direct solver for aerodynamic analysis solves the Reynolds Averaged Navier Stokes (RANS) equations, where the effect of the turbine rotor is modeled as momentum sources using the actuator disk model (ADM); this approach is referred to as RANS/ADM. The inverse problem is posed as follows: for a given selection of airfoils, the objective is to find the blade geometry (described as blade twist and chord distributions) which realizes the desired turbine aerodynamic performance at the design point; …
Cross-flow turbines, also known as vertical-axis turbines, have numerous features that make them attractive for wind and marine renewable energy. To maximize power output, the turbine blade kinematics may be controlled during the course of the blade revolution, thus optimizing the unsteady fluid dynamic forces. Dynamically pitching the blades, similar to blade control in a helicopter, is an established method. However, this technique adds undesirable mechanical complexity to the turbine, increasing cost and reducing durability. Here we introduce a novel alternative requiring no additional movi…
This work presents an investigation on different methods for the calculation of the angle of attack and the underlying induced velocity on wind turbine blades using data obtained from three-dimensional Computational Fluid Dynamics (CFD). Several methods are examined and their advantages, as well as shortcomings, are presented. The investigations are performed for two 10MW reference wind turbines under axial inflow conditions, namely the turbines designed in the EU AVATAR and INNWIND.EU projects. The results show that the evaluated methods are in good agreement with each other at the mid-span, …
Modelling of turbine blade-induced turbulence (BIT) is discussed within the framework of three-dimensional Reynolds-averaged Navier-Stokes (RANS) actuator disk computations. We first propose a generic (baseline) BIT model, which is applied only to the actuator disk surface, does not include any model coefficients (other than those used in the original RANS turbulence model) and is expected to be valid in the limiting case where BIT is fully isotropic and in energy equilibrium. The baseline model is then combined with correction functions applied to the region behind the disk to account for the…
Vertical-axis wind turbines are great candidates to diversify wind energy technology, but their aerodynamic complexity limits industrial deployment. To improve the efficiency and lifespan of vertical axis wind turbines, we desire data-driven models and control strategies that take into account the timing and duration of subsequent events in the unsteady flow development. Here, we aim to characterise the chain of events that leads to dynamic stall on a vertical-axis wind turbine blade and to quantify the influence of the turbine operation conditions on the duration of the individual flow develo…
Steady-state response of an isolated horizontal axis wind turbine blade undergoing out-of-plane and in-plane vibrations are studied considering the two cases separately. Equations of motion for both cases are sought by modeling the blade as cantilevered Euler-Bernoulli beam and applying the Lagrangian formulation. Taking into account the effects of blade rotation on gravitational and aerodynamic forces and allowing the blade to undergo large deformations, various nonlinearities arise in the system resulting in superharmonic resonances. Taking practically relevant numerical values of parameters…
The paper presents a stochastic approach to estimate the aerodynamic forces with local dynamics on wind turbine blades in unsteady wind inflow. This is done by integrating a stochastic model of lift and drag dynamics for an airfoil into the aerodynamic simulation software AeroDyn. The model is added as an alternative to the static table lookup approach in blade element momentum (BEM) wake model used by AeroDyn. The stochastic forces are obtained for a rotor blade element using full field turbulence simulated wind data input and compared with the classical BEM and dynamic stall models for ident…
Actuator line model has been widely employed in wind turbine simulations. However, the standard actuator line model does not include a model for the turbine nacelle which can significantly impact turbine wake characteristics as shown in the literature. Another disadvantage of the standard actuator line model is that more geometrical features of turbine blades cannot be resolved on a finer mesh. To alleviate these disadvantages of the standard model, we develop a new class of actuator surface models for turbine blades and nacelle to take into account more geometrical details of turbine blades a…
Super-large-scale particle image velocimetry (SLPIV) using natural snowfall is used to investigate the influence of nacelle and tower generated flow structures on the near-wake of a 2.5 MW wind turbine at the EOLOS field station. The analysis is based on the data collected in a field campaign on March 12th, 2017, with a sample area of 125 m (vertical) x 70 m (streamwise) centred on the plane behind the turbine support tower. The SLPIV measurement provides the velocity field over the entire rotor span, revealing a region of accelerated flow around the hub caused by the reduction in axial induct…
Tidal currents are renewable and predictable energy sources that could prove fundamental to decrease dependency from fossil fuels. Tidal currents, however, are highly unsteady and non uniform, resulting in undesirable load fluctuations on the blades and the drive train of turbines. A passive morphing blade concept capable to reduce the load fluctuations without affecting the mean loads has recently been formulated and demonstrated with numerical simulations (Pisetta et al., 2022). In this paper, we present the first demonstration of this morphing blade concept, through experimental tests on a …
To design and optimize arrays of vertical-axis wind turbines (VAWTs) for maximal power density and minimal wake losses, a careful consideration of the inherently three-dimensional structure of the wakes of these turbines in real operating conditions is needed. Accordingly, a new volumetric particle-tracking velocimetry method was developed to measure three-dimensional flow fields around full-scale VAWTs in field conditions. Experiments were conducted at the Field Laboratory for Optimized Wind Energy (FLOWE) in Lancaster, CA, using six cameras and artificial snow as tracer particles. Velocity a…
Computational fluid dynamics (CFD) studies are carried out on a two-bladed vertical axis wind turbine (VAWT) operating at a wind speed of 8 m/s for the tip speed ratios ($λ$) of 0.50 - 3.0. The blade consists of the NACA 0021 airfoil with the chord length of 0.265 m and a rotor radius of 1 m. Basic sensitivity studies for various time step sizes are carried out. The results are validated against available measurement data from literature. An excellent agreement is obtained for small $λ$ up to optimum condition. For the higher tip speed ratios, the two dimensional CFD computations predict highe…
We present results from novel field, lab and computer studies, that pave the way towards non-invasive classification of localised surface defects on running wind turbine rotors using infrared thermography (IRT). In particular, we first parametrise the problem from a fluid dynamical point of view using the roughness Reynolds number ($Re_k$) and demonstrate how the parameter regime relevant for modern wind turbines translate to parameter values that are currently feasible in typical wind tunnel and computer experiments. Second, we discuss preparatory wind tunnel and field measurements, that demo…
Flow past a high-lift low-pressure turbine (LPT) blade in a cascade could be quite complex as phenomena like separation and transition are often involved. For a highly loadedT106A blade at a high incidence and relatively low Reynolds number(25, 000 < Re < 1, 00, 000), separation-induced transition is observed on the suction side of the blade, making it a challenging problem for model-based simulations. In this work, computations for this flow are carried out using RANS and hybrid LES/RANS approaches. The RANS simulations are performed with six popular low- Re turbulence models. While turbulenc…
A direct transient growth analysis for three-dimensional perturbations to flow past a periodic array of T-106/300 low-pressure turbine fan blades is presented. The methodology is based on a singular value decomposition of the flow evolution operator, linearised about a steady or periodic base flow. This analysis yields the optimal growth modes. Previous work on global mode stability analysis of this flow geometry showed the flow is asymptotically stable, indicating a non-modal explanation of transition may be more appropriate. The present work extends previous investigations into the transient…
This study explored the aerodynamics of a new multi-stage co-axial vertical-axis wind turbine based on bio-inspiration from natural swimming habit of fish. The turbine was formed from a conventional straight-bladed vertical-axis turbine (VAWT) with a small inner rotor, also of three blades. The azimuthal and radial locations of the inner rotor were varied. Using numerical simulations, performance of the proposed new design was evaluated over a range of tip-speed ratios. The preliminary results identified a 600% increase in power output for multi-stage VAWTs at tip-speed rations TSR = 0 - 3, an…
The fluid dynamics video considers an array of two NREL 5-MW turbines separated by seven rotor diameters in a neutral atmospheric boundary layer (ABL). The neutral atmospheric boundary-layer flow data were obtained from a precursor ABL simulation using a Large-Eddy Simulation (LES) framework within OpenFOAM. The mean wind speed at hub height is 8m/s, and the surface roughness is 0.2m. The actuator line method (ALM) is used to model the wind turbine blades by means of body forces added to the momentum equation. The fluid dynamics video shows the root and tip vortices emanating from the blades f…
The actuator line model (ALM) is a commonly used method to represent lifting surfaces such as wind turbine blades within Large-Eddy Simulations (LES). In the ALM the lift and drag forces are replaced by an imposed body force which is typically smoothed over several grid points using a Gaussian kernel with some prescribed smoothing width $ε$. To date, the choice of $ε$ has most often been based on numerical considerations related to the grid spacing used in LES. However, especially for finely resolved LES with grid spacings on the order of or smaller than the chord-length of the blade, the best…
We present first results of an implicit large eddy simulation of the MTU T161 low pressure turbine at a Reynolds number of 90,000 and Mach number of 0.6, both based on isentropic exit conditions, using a high order discontinuous Galerkin method. The aim is to validate the numerical setup with respect to available experimental data. We discuss the steps taken to create realistic inflow boundary conditions in terms of end wall boundary layer thickness and free stream turbulence intensity. This is achieved by tailoring the input distribution of Reynolds stresses and turbulent length scale to a Fo…
Atmospheric turbulent velocity fluctuations are known to increase wind turbine structural loading and accelerate wake recovery, but the impact of vortical coherent structures in the atmosphere on wind turbines has not yet been evaluated. The current study uses flow imaging with natural snowfall with a field of view spanning the inflow and near wake. Vortical coherent structures with diameters on the order of 1 m are identified and characterized in the flow approaching a 2.5 MW wind turbine in the region spanning the bottom blade tip elevation to hub height. Their impact on turbine structural l…
This article presents two model-free controllers for wind-turbine torque and pitch control. These controllers are based on reinforcement learning (RL) and Bayesian optimization (BO) and do not rely on any mathematical model of the wind-turbine dynamics, in contrast to classical approaches designed on linearized models. The model-free controllers were benchmarked against a proportional-integral-derivative (PID) regulator in a numerical environment using Blade Element Momentum theory for computing the aerodynamic torque and the blade loads. The results showed that the model-free approaches could…
Reducing wake losses in wind farms by deflecting the wakes through turbine yawing has been shown to be a feasible wind farm controls approach. Nonetheless, the effectiveness of yawing depends not only on the degree of wake deflection but also on the resulting shape of the wake. In this work, the deflection and morphology of wakes behind a wind turbine operating in yawed conditions are studied using wind tunnel experiments of a wind turbine modeled as a porous disk in a uniform inflow. First, by measuring velocity distributions at various downstream positions and comparing with prior studies, w…
In order to enable simulations of developing wind turbine array boundary layers with highly realistic inflow conditions a concurrent precursor method for Large Eddy Simulations is proposed. In this method we consider two domains simultaneously, i.e. in one domain a turbulent Atmospheric Boundary Layer (ABL) without wind turbines is simulated in order to generate the turbulent inflow conditions for a second domain in which the wind turbines are placed. The benefit of this approach is that a) it avoids the need for large databases in which the turbulent inflow conditions are stored and the corre…
Cross-flow turbines convert kinetic power in wind or water currents to mechanical power. Unlike axial-flow turbines, the influence of geometric parameters on turbine performance is not well-understood, in part because there are neither generalized analytical formulations nor inexpensive, accurate numerical models that describe their fluid dynamics. Here, we experimentally investigate the effect of aspect ratio - the ratio of the blade span to rotor diameter - on the performance of a straight-bladed cross-flow turbine in a water channel. To isolate the effect of aspect ratio, all other non-dime…
A Wells turbine is an axial-flow turbine consisting of a rotor usually with symmetric (uncambered) blades staggered at a 90 degree angle relative to the incoming flow. This turbine is used within oscillating water column (OWC) systems, which convert the sea-wave motion into a bi-directional flow of air. During its normal operation, the turbine blades experience a continuous change in incidence angle. that according to many authors is at the origin of an hysteresis in its force coefficients. Aerodynamic hysteresis in rapidly moving airfoils is a well-known phenomenon, but happens only at non-di…
High-order large-eddy simulations are performed to study the performance and flow field of a ducted wind turbine operating at different tip speed ratios. To evaluate the effects of the duct, simulations with the same tip speed ratios are also performed on the corresponding open-rotor turbine. It is found that the ducted turbine consistently obtains higher power outputs than the open-rotor counterpart, and the duct itself enhances flow turbulence and blade trailing-edge vortices but weakens tip and hub vortices. Flow bifurcation is observed at the largest tip speed ratio and is identified to be…
We evaluate the accuracy of the actuator line model (ALM) approach by performing simulations for the NREL~5~MW wind turbine in uniform inflow using three large eddy simulation codes. The power and thrust coefficients obtained using the three codes agrees within $1\%$ when the grid spacing $Δ_{\rm grid} \le 5.25$~m, and are cross-validated against blade element momentum (BEM) theory. We find that the results of ALM converge towards BEM theory without the need for tip correction when the numerical resolution is increased. For $Δ_{\rm grid}=0.98$~m the difference between the power and thrust coef…
Here we have investigated the usage of a Dielectric Barrier Discharge (DBD) plasma actuator to improve the aerodynamic performance of an offshore 6MW wind turbine. By controlling the aerodynamic load at different blade sections, the overall generated power and the blade loading is improved. The blade is divided to seven segments and the analysis is applied to each segment. To study effects of configuration and location, actuators were installed in a single or tandem configuration, spread between 46% and 56% of the span length, at different chord wise locations. The improved phenomenological mo…
