Large-scale multiple-antenna systems have been identified as a promising technology for the next generation of wireless systems. However, by scaling up the number of receive antennas the energy consumption will also increase. One possible solution is to use low-resolution analog-to-digital converters at the receiver. This paper considers large-scale multiple-antenna uplink systems with 1-bit analog-to-digital converters on each receive antenna. Since oversampling can partially compensate for the information loss caused by the coarse quantization, the received signals are firstly oversampled by a factor M. We then propose a low-resolution aware linear minimum mean-squared error channel estimator for 1-bit oversampled systems. Moreover, we characterize analytically the performance of the proposed channel estimator by deriving an upper bound on the Bayesian Cramér-Rao bound. Numerical results are provided to illustrate the performance of the proposed channel estimator.
Large-scale multiple-antenna systems with large bandwidth are fundamental for future wireless communications, where the base station employs a large antenna array. In this scenario, one problem faced is the large energy consumption as the number of receive antennas scales up. Recently, low-resolution analog-to-digital converters (ADCs) have attracted much attention. Specifically, 1-bit ADCs are suitable for such systems due to their low cost and low energy consumption. This paper considers uplink large-scale multiple-antenna systems with 1-bit ADCs on each receive antenna. We investigate the b…
In this work, we investigate dynamic oversampling techniques for large-scale multiple-antenna systems equipped with low-cost and low-power 1-bit analog-to-digital converters at the base stations. To compensate for the performance loss caused by the coarse quantization, oversampling is applied at the receiver. Unlike existing works that use uniform oversampling, which samples the signal at a constant rate, a novel dynamic oversampling scheme is proposed. The basic idea is to perform time-varying nonuniform oversampling, which selects samples with nonuniform patterns that vary over time. We cons…
In this paper, the channel of an indoor holographic multiple-input multiple-output (MIMO) system is measured. It is demonstrated through experiments for the first time that the spatial oversampling of holographic MIMO systems is able to increase the capacity of a wireless communication system significantly. However, the antenna efficiency is the most crucial challenge preventing us from getting the capacity improvement. An extended EM-compliant channel model is also proposed for holographic MIMO systems, which is able to take the non-isotropic characteristics of the propagation environment, th…
Low-resolution devices are promising for systems that demand low energy consumption and low complexity as required in IoT systems. In this study, we propose a novel waveform for bandlimited channels with 1-bit quantization and oversampling at the receivers. The proposed method implies that the information is conveyed within the time instances of zero-crossings which is then utilized in combination with a Gray-coding scheme. Unlike the existing method, the proposed method does not require optimization and transmission of a dynamic codebook. The proposed approach outperforms the state-of-the-art…
Massive multiple-input multiple-output (MIMO) systems have attracted much attention lately due to the many advantages they provide over single-antenna systems. Owing to the many antennas, low-cost implementation and low power consumption per antenna are desired. To that end, massive MIMO structures with low-resolution analog-to-digital converters (ADC) have been investigated in many studies. However, the effect of a strong interferer in the adjacent band on quantized massive MIMO systems have not been examined yet. In this study, we analyze the performance of uplink massive MIMO with low-resol…
In this paper, we propose an oversampling based low-resolution aware least squares channel estimator for large-scale multiple-antenna systems with 1-bit analog-to-digital converters on each receive antenna. To mitigate the information loss caused by the coarse quantization, oversampling is applied at the receiver, where the sampling rate is faster than the Nyquist rate. We also characterize analytical performances, in terms of the deterministic Cramér-Rao bounds, on estimating the channel parameters. Based on the correlation of the filtered noise, both the Fisher information for white noise an…
A channel with continuous phase modulation and 1-bit ADC with oversampling is considered. Due to oversampling, higher-order modulations yield a higher achievable rate and this work presents a method to approach this with sophisticated coding. A tailored bit mapping is proposed where two bits can be detected reliably at high SNR and only the third bit suffers from an error floor. With this, a convolutional code is only applied to the third bit. Our experiments with a turbo receiver show that the proposed method corresponds to a lower BER in comparison to the case of conventional channel coding.
In this paper we investigate the achievable rate of LOS MIMO systems that use 1-bit quantization and spatial oversampling at the receiver. We propose that by using additional antennas at the receiver, the loss incurred due to the strong limitation of the quantization can be decreased. Mutual information results show that considerable rate gains can be achieved depending on the number and arrangement of the antennas. In some of the cases, even the full available rate from the transmitter can be attained. Furthermore, the results also reveal that two-dimensional antenna arrays can benefit more f…
Oversampling combined with low quantization resolutions has been shown to be a viable option when aiming for energy efficiency in multigigabit/s communications systems. This work considers the case of 1-bit quantization combined with oversampling and shows how the performance of such a system can be improved by using matched pulse shaping filters and faster than Nyquist signaling. The channel is considered with additive Gaussian noise and the performance of the system is evaluated in terms of achievable information rate under symbol-by-symbol detection.
To relax power consumption requirements in multigigabit/s communications systems low resolution quantization can be used. Information-theoretic results have shown that systems employing 1-bit quantization and oversampling are a viable option for this. This work investigates such a structure under the influence of additive Gaussian noise and two matched pulse shaping filters. It is described how a BCJR algorithm, based on a finite-state channel assumption, can be used to reconstruct symbols of higher order modulation schemes that allow the transmission of more than one bit per symbol. Furthermo…
We investigate design and performance of communications over the bandlimited Gaussian channel with one-bit output quantization. A transceiver structure is proposed, which generates the channel input using a finite set of time-limited and approximately bandlimited waveforms, and performs oversampling on the channel output by an integrate-and-dump filter preceding the one-bit quantizer. The waveform set is constructed based on a specific bandlimited random process with certain zero-crossing properties which can be utilized to convey information. In the presence of the additive white Gaussian noi…
Continuous phase modulation (CPM) with 1-bit quantization at the receiver is promising in terms of energy and spectral efficiency. In this study, CPM waveforms with symbol durations significantly shorter than the inverse of the signal bandwidth are proposed, termed faster-than-Nyquist CPM. This configuration provides a better steering of zero-crossings as compared to conventional CPM. Numerical results confirm a superior performance in terms of BER in comparison with state-of-the-art methods, while having the same spectral efficiency and a lower oversampling factor. Moreover, the new waveform …
Quantized channel state information (CSI) plays a critical role in precoding design which helps reap the merits of multiple-input multiple-output (MIMO) technology. In order to reduce the overhead of CSI feedback, we propose a deep learning based CSI quantization method by developing a joint convolutional residual network (JCResNet) which benefits MIMO channel feature extraction and recovery from the perspective of bit-level quantization performance. Experiments show that our proposed method substantially improves the performance.
This paper considers uplink massive MIMO systems with 1-bit analog-to-digital converters (ADCs) and develops a deep-learning based channel estimation framework. In this framework, the prior channel estimation observations and deep neural network models are leveraged to learn the non-trivial mapping from quantized received measurements to channels. For that, we derive the sufficient length and structure of the pilot sequence to guarantee the existence of this mapping function. This leads to the interesting, and \textit{counter-intuitive}, observation that when more antennas are employed by the …
In large-scale antenna systems, using one-bit analog-to-digital converters (ADCs) has recently become important since they offer significant reductions in both power and cost. However, in contrast to high-resolution ADCs, the coarse quantization of one-bit ADCs results in an irreversible loss of information. In the context of channel estimation, studies have been developed extensively to combat the performance loss incurred by one-bit ADCs. Furthermore, in the field of array signal processing, direction-of-arrival (DOA) estimation combined with one-bit ADCs has gained growing interests recentl…
We propose a novel low-resolution-aware recursive least squares channel estimation algorithm for uplink multi-user multiple-input multiple-output systems. In order to reduce the energy consumption, 1-bit ADCs are used on each receive antenna. The loss of performance can be recovered by the large-scale antenna arrays at the receiver. The proposed adaptive channel estimator can mitigate the distortions due to the coarse quantization. Moreover, we propose a low-resolution-aware minimum mean square error based successive interference canceler to successively mitigate the multiuser interference. Si…
Today's communication systems typically use high resolution analog-to-digital converters (ADCs). However, considering future communication systems with data rates in the order of 100Gbit/s the ADC power consumption becomes a major factor due to the high sampling rates. A promising alternative are receivers based on 1-bit quantization and oversampling w.r.t. the signal bandwidth. Such an approach requires a redesign of modulation, receiver synchronization, and demapping. A zero crossing modulation is a natural choice as the information needs to be carried in the zero crossing time instants. The…
In Massive MIMO base stations (BSs), the hardware design needs to balance high spectral efficiency (SE) with low complexity. The level of hardware impairments (HWIs) indicates how strong the signal distortion introduced by hardware imperfections is. In particular, the analog-to-digital converters (ADCs) have an important impact on signal distortion and power consumption. This article addresses the fundamental problem of selecting the optimal hardware quality in the Massive MIMO space. In particular, we examine the optimal HWI and ADC bit allocation per BS antenna to maximize the SE. The result…
We consider wireless communication systems with compact planar arrays having densely spaced antenna elements in conjunction with one-bit analog-to-digital and digital-to-analog converters (ADCs/DACs). We provide closed-form expressions for the achievable rates with simple linear processing techniques for the uplink as well as the downlink scenarios while taking into account the effects of antenna mutual coupling. In the downlink case, we introduce the concept of non-radiating dithering to combat correlations of the quantization errors. Under higher antenna element density, we show that the per…
Communication systems with low-resolution analog-to-digital-converters (ADCs) can exploit channel state information at the transmitter (CSIT) and receiver. This paper presents initial results on codebook design and performance analysis for limited feedback systems with one-bit ADCs. Different from the high-resolution case, the absolute phase at the receiver is important to align the phase of the received signals when the received signal is sliced by one-bit ADCs. A new codebook design for the beamforming case is proposed that separately quantizes the channel direction and the residual phase.
The combination of orthogonal frequency modulation (OFDM) and multiple-input multiple-output (MIMO) systems plays an important role in modern communication systems. In order to meet the growing throughput demands, future MIMO-OFDM receivers are expected to utilize a massive number of antennas, operate in dynamic environments, and explore high frequency bands, while satisfying strict constraints in terms of cost, power, and size. An emerging technology to realize massive MIMO receivers of reduced cost and power consumption is based on dynamic metasurface antennas (DMAs), which inherently implem…
This paper investigates the minimum energy required to transmit $k$ information bits with a given reliability over a multiple-antenna Rayleigh block-fading channel, with and without channel state information (CSI) at the receiver. No feedback is assumed. It is well known that the ratio between the minimum energy per bit and the noise level converges to $-1.59$ dB as $k$ goes to infinity, regardless of whether CSI is available at the receiver or not. This paper shows that lack of CSI at the receiver causes a slowdown in the speed of convergence to $-1.59$ dB as $k\to\infty$ compared to the case…
The one-bit spatial Sigma-Delta concept has recently been proposed as an approach for achieving low distortion and low power consumption for massive multi-input multi-output systems. The approach exploits users located in known angular sectors or spatial oversampling to shape the quantization noise away from desired directions of arrival. While reducing the antenna spacing alleviates the adverse impact of quantization noise, it can potentially deteriorate the performance of the massive array due to excessive mutual coupling. In this paper, we analyze the impact of mutual coupling on the uplink…
A comparative resource allocation analysis in terms of received bits-per-antenna spectral efficiency (SE) and energy efficiency (EE) in downlink (DL) single-cell massive multiple-input multiple-output (mMIMO) and non-orthogonal multiple access (NOMA) systems considering a BS equipped with many ($M$) antennas, while $K$ devices {operate} with a single-antenna, and {the loading of devices} $ρ= \frac{K}{M}$ ranging in $0<ρ\leq 2$ is carried out under three different \ac{PA} strategies: the inverse of the channel power allocation (PICPA), a modified water-filling ($Δ$-WF) allocation method, and th…
The minimum average signal-to-noise ratio (SNR) per bit required for error-free transmission over a fading channel is derived, and is shown to be equal to that of the additive white Gaussian noise (AWGN) channel, which is $-1.6$ dB. Discrete-time algorithms are presented for timing and carrier synchronization, as well as channel estimation, for turbo coded multiple input multiple output (MIMO) orthogonal frequency division multiplexed (OFDM) systems. Simulation results show that it is possible to achieve a bit error rate of $10^{-5}$ at an average SNR per bit of 5.5 dB, using two transmit and …
We examine the uplink spectral efficiency of a massive MIMO base station employing a one-bit Sigma-Delta sampling scheme implemented in the spatial rather than the temporal domain. Using spatial rather than temporal oversampling, and feedback of the quantization error between adjacent antennas, the method shapes the spatial spectrum of the quantization noise away from an angular sector where the signals of interest are assumed to lie. It is shown that, while a direct Bussgang analysis of the Sigma-Delta approach is not suitable, an alternative equivalent linear model can be formulated to facil…
This paper studies the design and optimization of a limited feedback single-user system with multiple-antenna transmitter and single-antenna receiver. The design problem is cast in form of the minimizing the average transmission power at the base station subject to the user's outage probability constraint. The optimization is over the user's channel quantization codebook and the transmission power control function at the base station. Our approach is based on fixing the outage scenarios in advance and transforming the design problem into a robust system design problem. We start by showing that…
In this paper, we focus on 1-bit precoding for large-scale antenna systems in the downlink based on the concept of constructive interference (CI). By formulating the optimization problem that aims to maximize the CI effect subject to the 1-bit constraint on the transmit signals, we mathematically prove that, when relaxing the 1-bit constraint, the majority of the obtained transmit signals already satisfy the 1-bit constraint. Based on this important observation, we propose a 1-bit precoding method via a partial branch-and-bound (P-BB) approach, where the BB procedure is only performed for the …
Sigma-Delta modulation is a popular method for analog-to-digital conversion of bandlimited signals that employs coarse quantization coupled with oversampling. The standard mathematical model for the error analysis of the method measures the performance of a given scheme by the rate at which the associated reconstruction error decays as a function of the oversampling ratio $λ$. It was recently shown that exponential accuracy of the form $O(2^{-rλ})$ can be achieved by appropriate one-bit Sigma-Delta modulation schemes. By general information-entropy arguments $r$ must be less than 1. The curren…
This paper addresses the optimal design of limited-feedback downlink multi-user spatial multiplexing systems. A multiple-antenna base-station is assumed to serve multiple single-antenna users, who quantize and feed back their channel state information (CSI) through a shared rate-limited feedback channel. The optimization problem is cast in the form of minimizing the average transmission power at the base-station subject to users' target signal-to-interference-plus-noise ratios (SINR) and outage probability constraints. The goal is to derive the feedback bit allocations among the users and the …
In this paper, the performance of indoor Terahertz (THz) communication systems with one-bit digital-to-analog converters (DACs) is investigated. Array-of-subarrays architecture is assumed for the antennas at the access points, where each RF chain uniquely activates a disjoint subset of antennas, each of which is connected to an exclusive phase shifter. Hybrid precoding, including maximum ratio transmission (MRT) and zero-forcing (ZF) precoding, is considered. The best beamsteering direction for the phase shifter in the large subarray antenna regime is first proved to be the direction of the li…
Base station (BS) architectures for massive multi-user (MU) multiple-input multiple-output (MIMO) wireless systems are equipped with hundreds of antennas to serve tens of users on the same time-frequency channel. The immense number of BS antennas incurs high system costs, power, and interconnect bandwidth. To circumvent these obstacles, sophisticated MU precoding algorithms that enable the use of 1-bit DACs have been proposed. Many of these precoders feature parameters that are, traditionally, tuned manually to optimize their performance. We propose to use deep-learning tools to automatically …
Massive multiuser (MU) multiple-input multiple- output (MIMO) is foreseen to be a key technology in future wireless communication systems. In this paper, we analyze the downlink performance of an orthogonal frequency division multiplexing (OFDM)-based massive MU-MIMO system in which the base station (BS) is equipped with 1-bit digital-to-analog converters (DACs). Using Bussgang's theorem, we characterize the performance achievable with linear precoders (such as maximal-ratio transmission and zero forcing) in terms of bit error rate (BER). Our analysis accounts for the possibility of oversampli…
In this paper we carry out the asymptotic diversity analysis for millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems by using bit interleaved coded multiple beamforming (BICMB). First, a single-user mmWave system which employs $M_t$ antenna subarrays at the transmitter and $M_r$ antenna subarrays at the receiver is studied. Each antenna subarray in the transmitter and the receiver has $N_r$ and $N_t$ antennas, respectively. We establish a theorem for the diversity gain when the number of antennas in each remote antenna unit (RAU) goes to infinity. Based on the theore…
This letter investigates bit-interleaved coded multiple beamforming (BICMB) with perfect coding in millimeter-wave (mm-wave) massive multiple-input multiple-output (MIMO) systems to achieve both maximum diversity gain and multiplexing gain. Using perfect coding with BICMB enables us to do this. We show that by using BICMB and perfect coding, the diversity gain becomes independent from the number of transmitted data streams and the number of antennas in each remote antenna unit (RAU) at the transmitter and the receiver. The assumption is that the perfect channel state information (CSI) is known…
In future high-capacity wireless systems based on mmWave or massive multiple input multiple output (MIMO), the power consumption of receiver Analog to Digital Converters (ADC) is a concern. Although hybrid or analog systems with fewer ADCs have been proposed, fully digital receivers with many lower resolution ADCs (and lower power) may be a more versatile solution. In this paper, focusing on an uplink scenario, we propose to take the optimization of ADC resolution one step further by enabling variable resolutions in the ADCs that sample the signal received at each antenna. This allows to give …
As future wireless systems trend towards higher carrier frequencies and large antenna arrays, receivers with one-bit analog-to-digital converters (ADCs) are being explored owing to their reduced power consumption. However, the combination of large antenna arrays and one-bit ADCs makes channel estimation challenging. In this paper, we formulate channel estimation from a limited number of one-bit quantized pilot measurements as an inverse problem and reconstruct the channel by optimizing the input vector of a pre-trained deep generative model with the objective of maximizing a novel correlation-…
We analyze limited feedback in systems where a multiple-antenna transmitter sends signals to single-antenna receivers with finite-bit ADCs. If channel state information (CSI) is not available with high resolution at the transmitter and the precoding is not well designed, the inter-user interference is a big decoding challenge for receivers with low-resolution quantization. In this paper, we derive achievable rates with finite-bit ADCs and finite-bit CSI feedback. The performance loss compared to the case with perfect CSI is then analyzed. The results show that the number of bits per feedback s…
Millimeter wave (mmWave) massive multiple-input multiple-output (massive MIMO) is one of the most promising technologies for the fifth generation and beyond wireless communication system. However, a large number of antennas incur high power consumption and hardware costs, and high-frequency communications place a heavy burden on the analog-to-digital converters (ADCs) at the base station (BS). Furthermore, it is too costly to equipping each antenna with a high-precision ADC in a large antenna array system. It is promising to adopt low-resolution ADCs to address this problem. In this paper, we …
Achieving high bit rates is the main goal of wireless technologies like 5G and beyond. This translates to obtaining high spectral efficiencies using large number of antennas at the transmitter and receiver (single user massive multiple input multiple output or SU-MMIMO). It is possible to have a large number of antennas in the mobile handset at mm-wave frequencies in the range $30 - 300$ GHz due to the small antenna size. In this work, we investigate the bit-error-rate (BER) performance of SU-MMIMO in two scenarios (a) using serially concatenated turbo code (SCTC) in uncorrelated channel and (…
This work deals with turbo coded single user massive multiple input multiple output (SU-MMIMO) systems, with and without precoding. SU-MMIMO has a much higher spectral efficiency compared to multi-user massive MIMO (MU-MMIMO) since independent signals are transmitted from each of the antenna elements (spatial multiplexing). MU-MMIMO that uses beamforming has a much lower spectral efficiency, since the same signal (with a delay) is transmitted from each of the antenna elements. In this work, expressions for the upper bound on the average signal-to-noise ratio (SNR) per bit and spectral efficien…
We present an optimized secure multi-antenna transmission approach based on artificial-noise-aided beamforming, with limited feedback from a desired single-antenna receiver. To deal with beamformer quantization errors as well as unknown eavesdropper channel characteristics, our approach is aimed at maximizing throughput under dual performance constraints - a connection outage constraint on the desired communication channel and a secrecy outage constraint to guard against eavesdropping. We propose an adaptive transmission strategy that judiciously selects the wiretap coding parameters, as well …
We study a downlink multi-user multiple-input single-output (MU-MISO) system in which the base station (BS) has a large number of antennas with cost-effective one-bit digital-to-analog converters (DACs). In this system, we first identify that antenna-selection can yield a non-trivial symbol-error-rate (SER) performance gain by alleviating an error-floor problem. Likewise the previous works on one-bit precoding, finding an optimal transmit-signal vector (encompassing precoding and antenna-selection) requires exhaustive-search due to its combinatorial nature. Motivated by this, we propose a low-…
We study multi-user massive multiple-input single-output (MISO) systems and focus on downlink transmission, where the base station (BS) employs a large antenna array with low-cost 1-bit digital-to-analog converters (DACs). The direct combination of existing beamforming schemes with 1-bit DACs is shown to lead to an error floor at medium-to-high SNR regime, due to the coarse quantization of the DACs with limited precision. In this paper, based on the constructive interference we consider both a quantized linear beamforming scheme where we analytically obtain the optimal beamforming matrix, and …
Capacity bounds are studied for the multiple-antenna complex Gaussian relay channel with t1 transmitting antennas at the sender, r2 receiving and t2 transmitting antennas at the relay, and r3 receiving antennas at the receiver. It is shown that the partial decode-forward coding scheme achieves within min(t1,r2) bits from the cutset bound and at least one half of the cutset bound, establishing a good approximate expression of the capacity. A similar additive gap of min(t1 + t2, r3) + r2 bits is shown to be achieved by the compress-forward coding scheme.
In this paper, we analyze the asymptotic performance of multiple antenna channels where the transmitter has either perfect or finite bit channel state information. Using the diversity-multiplexing tradeoff to characterize the system performance, we demonstrate that channel feedback can fundamentally change the system behavior. Even one-bit of information can increase the diversity order of the system compared to the system with no transmitter information. In addition, as the amount of channel information at the transmitter increases, the diversity order for each multiplexing gain increases and…
Consider the following problem: A multi-antenna base station (BS) sends multiple symbol streams to multiple single-antenna users via precoding. However, unlike conventional multiuser precoding, the transmitted signals are subjected to binary, unit-modulus, or even discrete unit-modulus constraints. Such constraints arise in the one-bit and constant-envelope (CE) massive MIMO scenarios, wherein high-resolution digital-to-analog converters (DACs) are replaced by one-bit DACs and phase shifters, respectively, for cutting down hardware cost and energy consumption. Multiuser precoding under one-bit…
It is shown that while the mutual information curves for coded modulation (CM) and bit interleaved coded modulation (BICM) overlap in the case of a single input single output channel, the same is not true in multiple input multiple output (MIMO) channels. A method for mitigating fading in the presence of multiple transmit antennas, named coordinate interleaving (CI), is presented as a generalization of component interleaving for a single transmit antenna. The extent of any advantages of CI over BICM, relative to CM, is analyzed from a mutual information perspective; the analysis is based on an…
We present a novel iterative detection and decoding scheme for the uplink of large-scale multiuser multiple-antenna systems. In order to reduce the receiver's energy consumption and computational complexity, 1-bit analog-to-digital converters are used in the front-end. The performance loss due to the 1-bit quantization can be mitigated by using large-scale antenna arrays. We propose a linear low-resolution-aware minimum mean square error detector for soft multiuser interference mitigation. Moreover, short block length low-density parity-check codes are considered for avoiding high latency. In …
Millimeter wave (mmWave) spectrum has drawn attention due to its tremendous available bandwidth. The high propagation losses in the mmWave bands necessitate beamforming with a large number of antennas. Traditionally each antenna is paired with a high-speed analog-to-digital converter (ADC), which results in high power consumption. A hybrid beamforming architecture and one-bit resolution ADCs have been proposed to reduce power consumption. However, analog beamforming and one-bit quantization make channel estimation more challenging. In this paper, we propose a narrowband channel estimation algo…
We aim at investigating the impact of low resolution digital-to-analog converters (DACs) at the transmitter and low resolution analog-to-digital converters (ADCs) at the receiver on the required bandwidth and the required signalto- noise ratio (SNR). In particular, we consider the extreme case of only 1-bit resolution (with oversampling), where we propose a single carrier system architecture for minimizing the spectral occupation and the required SNR of 1-bit signals. In addition, the receiver is optimized to take into account the effects of quantization at both ends. Through simulations, we s…
