We analyze limited feedback in systems where a multiple-antenna transmitter sends signals to single-antenna receivers with finite-bit ADCs. If channel state information (CSI) is not available with high resolution at the transmitter and the precoding is not well designed, the inter-user interference is a big decoding challenge for receivers with low-resolution quantization. In this paper, we derive achievable rates with finite-bit ADCs and finite-bit CSI feedback. The performance loss compared to the case with perfect CSI is then analyzed. The results show that the number of bits per feedback should increase linearly with the ADC resolution to restrict the loss.
A one-bit wireless transceiver is a promising communication architecture that not only can facilitate the design of mmWave communication systems but also can extremely diminish power consumption. The non-linear distortion effects by one-bit quantization at the transceiver, however, change the fundamental limits of communication rates. In this paper, the capacity of a multiple-input single-output (MISO) fading channel with one-bit transceiver is characterized in a closed form when perfect channel state information (CSI) is available at both a transmitter and a receiver. One major finding is tha…
Communication systems with low-resolution analog-to-digital-converters (ADCs) can exploit channel state information at the transmitter and receiver. This paper presents codebook designs and performance analyses for limited feedback MIMO systems with finite-bit ADCs. A point-to-point single-user channel is firstly considered. When the received signal is sliced by 1-bit ADCs, the absolute phase at the receiver is important to align the phase of the received signals. A new codebook design for beamforming, which separately quantizes the channel direction and the residual phase, is therefore propos…
In future high-capacity wireless systems based on mmWave or massive multiple input multiple output (MIMO), the power consumption of receiver Analog to Digital Converters (ADC) is a concern. Although hybrid or analog systems with fewer ADCs have been proposed, fully digital receivers with many lower resolution ADCs (and lower power) may be a more versatile solution. In this paper, focusing on an uplink scenario, we propose to take the optimization of ADC resolution one step further by enabling variable resolutions in the ADCs that sample the signal received at each antenna. This allows to give …
In this paper, we present a successive-cancellation-soft-output (SCSO) detector for an uplink multiuser multiple-input-multiple-output (MU-MIMO) system with one-bit analog-to-digital converters (ADCs). The proposed detector produces soft outputs (e.g., log-likelihood ratios (LLRs)) from one-bit quantized observations in a successive way: each user k's message is sequentially decoded from a channel decoder $k$ for $k=1,...,K$ in that order, and the previously decoded messages are exploited to improve the reliabilities of LLRs. Furthermore, we develop an efficient greedy algorithm to optimize a …
We develop a broadband channel estimation algorithm for millimeter wave (mmWave) multiple input multiple output (MIMO) systems with few-bit analog-to-digital converters (ADCs). Our methodology exploits the joint sparsity of the mmWave MIMO channel in the angle and delay domains. We formulate the estimation problem as a noisy quantized compressed-sensing problem and solve it using efficient approximate message passing (AMP) algorithms. In particular, we model the angle-delay coefficients using a Bernoulli-Gaussian-mixture distribution with unknown parameters and use the expectation-maximization…
The fundamental limits of communication over multiple-input multiple-output (MIMO) networks are considered when a limited number of one-bit analog to digital converters (ADC) are used at the receiver terminals. Prior works have mainly focused on point-to-point communications, where receiver architectures consisting of a concatenation of an analog processing module, a limited number of one-bit ADCs with non-adaptive thresholds, and a digital processing module are considered. In this work, a new receiver architecture is proposed which utilizes adaptive threshold one-bit ADCs - where the ADC thre…
We propose a novel low-resolution-aware recursive least squares channel estimation algorithm for uplink multi-user multiple-input multiple-output systems. In order to reduce the energy consumption, 1-bit ADCs are used on each receive antenna. The loss of performance can be recovered by the large-scale antenna arrays at the receiver. The proposed adaptive channel estimator can mitigate the distortions due to the coarse quantization. Moreover, we propose a low-resolution-aware minimum mean square error based successive interference canceler to successively mitigate the multiuser interference. Si…
Analog-to-digital converters (ADCs) stand for a significant part of the total power consumption in a massive MIMO base station. One-bit ADCs are one way to reduce power consumption. This paper presents an analysis of the spectral efficiency of single-carrier and OFDM transmission in massive MIMO systems that use one-bit ADCs. A closed-form achievable rate, i.e., a lower bound on capacity, is derived for a wideband system with a large number of channel taps that employs low-complexity linear channel estimation and symbol detection. Quantization results in two types of error in the symbol detect…
We propose a fast and near-optimal approach to joint channel-estimation, equalization, and decoding of coded single-carrier (SC) transmissions over frequency-selective channels with few-bit analog-to-digital converters (ADCs). Our approach leverages parametric bilinear generalized approximate message passing (PBiGAMP) to reduce the implementation complexity of joint channel estimation and (soft) symbol decoding to that of a few fast Fourier transforms (FFTs). Furthermore, it learns and exploits sparsity in the channel impulse response. Our work is motivated by millimeter-wave systems with band…
We develop a method to jointly estimate the carrier frequency offset (CFO) and the narrowband channel in millimeter wave (mmWave) MIMO systems operating with one-bit analog-to-digital converters (ADCs). We assume perfect timing synchronization and transform the underlying CFO-channel optimization problem to a higher dimensional space using lifting techniques. Exploiting the sparsity of mmWave MIMO channels in the angle domain, we perform joint estimation by solving a noisy quantized compressed sensing problem of the lifted version, using generalized approximate message passing. Simulation resu…
A potential tremendous spectrum resource makes millimeter wave (mmWave) communications a promising technology. High power consumption due to a large number of antennas and analog-to-digital converters (ADCs) for beamforming to overcome the large propagation losses is problematic in practice. As a hybrid beamforming architecture and low-resolution ADCs are considered to reduce power consumption, estimation of mmWave channels becomes challenging. We evaluate several channel estimation algorithms for wideband mmWave systems with hybrid beamforming and low-resolution ADCs. Through simulation, we s…
In large-scale antenna systems, using one-bit analog-to-digital converters (ADCs) has recently become important since they offer significant reductions in both power and cost. However, in contrast to high-resolution ADCs, the coarse quantization of one-bit ADCs results in an irreversible loss of information. In the context of channel estimation, studies have been developed extensively to combat the performance loss incurred by one-bit ADCs. Furthermore, in the field of array signal processing, direction-of-arrival (DOA) estimation combined with one-bit ADCs has gained growing interests recentl…
High resolution analog to digital converters (ADCs) are conventionally used at the receiver terminals to store an accurate digital representation of the received signal, thereby allowing for reliable decoding of transmitted messages. However, in a wide range of applications, such as communication over millimeter wave and massive multiple-input multiple-output (MIMO) systems, the use of high resolution ADCs is not feasible due to power budget limitations. In the conventional fully digital receiver design, where each receiver antenna is connected to a distinct ADC, reducing the ADC resolution le…
In this letter, we propose a two-stage approach to estimate the carrier frequency offset (CFO) and channel with one-bit analog-to-digital converters (ADCs). Firstly, a simple metric which is only a function of the CFO is proposed, and the CFO is estimated via solving the one-dimensional optimization problem. Secondly, the generalized approximate message passing (GAMP) algorithm combined with expectation maximization (EM) method is utilized to estimate the channel. In order to provide a benchmark of our proposed algorithm in terms of the CFO estimation, the corresponding Cramér-Rao bound (CRB) …
In this paper, we investigate the capacity of massive multiple-input multiple-output (MIMO) systems corrupted by complex-valued additive white Gaussian noise (AWGN) when both the transmitter and the receiver employ 1-bit digital-to-analog converters (DACs) and 1-bit analog-to-digital-converters (ADCs). As a result of 1-bit DACs and ADCs, the transmitted and received symbols, as well as the transmit- and receive-side channel state information (CSI), are assumed to be quantized to 1-bit of information. The derived results show that the capacity of the considered massive MIMO system is $2N$ and $…
This paper focuses on channel estimation in single-user and multi-user MIMO systems with multi-antenna base stations equipped with 1-bit spatial sigma-delta analog-to-digital converters (ADCs). A careful selection of the quantization voltage level and phase shift used in the feedback loop of 1-bit sigma-delta ADCs is critical to improve its effective resolution. We first develop a quantization noise model for 1-bit spatial sigma-delta ADCs. Using the developed noise model, we then present a two-step channel estimation algorithm to estimate a multipath channel parameterized by the gains, angles…
We present a novel iterative detection and decoding scheme for the uplink of large-scale multiuser multiple-antenna systems. In order to reduce the receiver's energy consumption and computational complexity, 1-bit analog-to-digital converters are used in the front-end. The performance loss due to the 1-bit quantization can be mitigated by using large-scale antenna arrays. We propose a linear low-resolution-aware minimum mean square error detector for soft multiuser interference mitigation. Moreover, short block length low-density parity-check codes are considered for avoiding high latency. In …
We study an uplink multiuser multiple-input multiple-output (MU-MIMO) system with one-bit analog-to-digital converters (ADCs). For such system, a supervised-learning (SL) detector has been recently proposed by modeling a non-linear end-to-end system function into a parameterized Bernoulli-like model. Despite its attractive performance, the SL detector requires a large amount of labeled data (i.e., pilot signals) to estimate the parameters of the underlying model accurately. This is because the amount of the parameters grows exponentially with the number of users. To overcome this drawback, we …
This paper presents a low-complexity near-maximum-likelihood-detection (near-MLD) algorithm called one-bit-sphere-decoding for an uplink massive multiple-input multiple-output (MIMO) system with one-bit analog-to-digital converters (ADCs). The idea of the proposed algorithm is to estimate the transmitted symbol vector sent by uplink users (a codeword vector) by searching over a sphere, which contains a collection of codeword vectors close to the received signal vector at the base station in terms of a weighted Hamming distance. To reduce the computational complexity for the construction of the…
Communication systems with low-resolution analog-to-digital-converters (ADCs) can exploit channel state information at the transmitter (CSIT) and receiver. This paper presents initial results on codebook design and performance analysis for limited feedback systems with one-bit ADCs. Different from the high-resolution case, the absolute phase at the receiver is important to align the phase of the received signals when the received signal is sliced by one-bit ADCs. A new codebook design for the beamforming case is proposed that separately quantizes the channel direction and the residual phase.
Advances in analog-to-digital converter (ADC) technology have opened up the possibility to directly digitize wideband radio frequency (RF) signals, avoiding the need for analog down-conversion. In this work, we consider an orthogonal frequency-division multiplexing (OFDM)-based massive multi-user (MU) multiple-input multiple-output (MIMO) uplink system that relies on direct RF-sampling at the base station and digitizes the received RF signals with 1-bit ADCs. Using Bussgang's theorem, we provide an analytical expression for the error-vector magnitude (EVM) achieved by digital down-conversion a…
Large-scale multiple-antenna systems with large bandwidth are fundamental for future wireless communications, where the base station employs a large antenna array. In this scenario, one problem faced is the large energy consumption as the number of receive antennas scales up. Recently, low-resolution analog-to-digital converters (ADCs) have attracted much attention. Specifically, 1-bit ADCs are suitable for such systems due to their low cost and low energy consumption. This paper considers uplink large-scale multiple-antenna systems with 1-bit ADCs on each receive antenna. We investigate the b…
This paper considers the channel estimation problem for massive multiple-input multiple-output (MIMO) systems that use one-bit analog-to-digital converters (ADCs). Previous channel estimation techniques for massive MIMO using one-bit ADCs are all based on single-shot estimation without exploiting the inherent temporal correlation in wireless channels. In this paper, we propose an adaptive channel estimation technique taking the spatial and temporal correlations into account for massive MIMO with one-bit ADCs. We first use the Bussgang decomposition to linearize the one-bit quantized received s…
This paper considers a multipair amplify-and-forward massive MIMO relaying system with one-bit ADCs and one-bit DACs at the relay. The channel state information is estimated via pilot training, and then utilized by the relay to perform simple maximum-ratio combining/maximum-ratio transmission processing. Leveraging on the Bussgang decomposition, an exact achievable rate is derived for the system with correlated quantization noise. Based on this, a closed-form asymptotic approximation for the achievable rate is presented, thereby enabling efficient evaluation of the impact of key parameters on …
This paper considers an uplink multiuser multiple-input-multiple-output (MU-MIMO) system with one-bit analog-to-digital converters (ADCs), in which $K$ users with a single transmit antenna communicate with one base station (BS) with $N_{\rm r}$ receive antennas. In this system, a novel MU-MIMO detection method, named weighted minimum distance (wMD) decoding, was recently proposed by introducing an equivalent coding problem. Despite of its attractive performance, the wMD decoding has the two limitations to be used in practice: i) the hard-decision outputs can degrade the performance of a channe…
Channel estimation at millimeter wave (mmWave) is challenging when large antenna arrays are used. Prior work has leveraged the sparse nature of mmWave channels via compressed sensing based algorithms for channel estimation. Most of these algorithms, though, assume perfect synchronization and are vulnerable to phase errors that arise due to carrier frequency offset (CFO) and phase noise. Recently sparsity-aware, non-coherent beamforming algorithms that are robust to phase errors were proposed for narrowband phased array systems with full resolution analog-to-digital converters (ADCs). Such ener…
Analog to Digital Converters (ADCs) are a major contributor to the energy consumption on the receiver side of millimeter-wave multiple-input multiple-output (MIMO) systems with large antenna arrays. Consequently, there has been significant interest in using low-resolution ADCs along with hybrid beam-forming at MIMO receivers for energy efficiency. However, decreasing the ADC resolution results in performance loss -- in terms of achievable rates -- due to increased quantization error. In this work, we study the application of practically implementable nonlinear analog operations, prior to sampl…
We consider the problem of channel estimation for uplink multiuser massive MIMO systems, where, in order to significantly reduce the hardware cost and power consumption, one-bit analog-to-digital converters (ADCs) are used at the base station (BS) to quantize the received signal. Channel estimation for one-bit massive MIMO systems is challenging due to the severe distortion caused by the coarse quantization. It was shown in previous studies that an extremely long training sequence is required to attain an acceptable performance. In this paper, we study the problem of optimal one-bit quantizati…
Utilizing intelligent reflecting surface (IRS) was proven to be efficient in improving the energy efficiency for wireless networks. In this paper, we investigate the passive beamforming and channel estimation for IRS assisted wireless communications with low-resolution analog-to-digital converters (ADCs) at the receiver. We derive the approximate achievable rate by using the Bussgang theorem. Based on the derived analytical achievable rate expression, we maximize the achievable rate by using semidefinite programming (SDP), branch-and-bound (BB), and gradient-based approaches. A maximum likelih…
In massive multiple-input multiple-output (MIMO) systems, it may not be power efficient to have a high-resolution analog-to-digital converter (ADC) for each antenna element. In this paper, a near maximum likelihood (nML) detector for uplink multiuser massive MIMO systems is proposed where each antenna is connected to a pair of one-bit ADCs, i.e., one for each real and imaginary component of the baseband signal. The exhaustive search over all the possible transmitted vectors required in the original maximum likelihood (ML) detection problem is relaxed to formulate an ML estimation problem. Then…
We present an analytical framework for the channel estimation and the data detection in massive multiple-input multiple-output uplink systems with 1-bit analog-to-digital converters (ADCs) and i.i.d. Rayleigh fading. First, we provide closed-form expressions of the mean squared error (MSE) of the channel estimation considering the state-of-the-art linear minimum MSE estimator and the class of scaled least-squares estimators. For the data detection, we provide closed-form expressions of the expected value and the variance of the estimated symbols when maximum ratio combining is adopted, which c…
We consider a complex Gaussian wiretap channel with finite-resolution analog-to-digital converters (ADCs) at both the legitimate receiver and the eavesdropper. For this channel, we show that a positive secrecy rate is always achievable as long as the channel gains at the legitimate receiver and at the eavesdropper are different, regardless of the quantization levels of the ADCs. For the achievability, we first consider the case of one-bit ADCs at the legitimate receiver and apply a binary input distribution where the two input points have the same phase when the channel gain at the legitimate …
Millimeter wave (mmWave) spectrum has drawn attention due to its tremendous available bandwidth. The high propagation losses in the mmWave bands necessitate beamforming with a large number of antennas. Traditionally each antenna is paired with a high-speed analog-to-digital converter (ADC), which results in high power consumption. A hybrid beamforming architecture and one-bit resolution ADCs have been proposed to reduce power consumption. However, analog beamforming and one-bit quantization make channel estimation more challenging. In this paper, we propose a narrowband channel estimation algo…
We derive an expression for the capacity of massive multiple-input multiple-output Millimeter wave (mmWave) channel where the receiver is equipped with a variable-resolution Analog to Digital Converter (ADC) and a hybrid combiner. The capacity is shown to be a function of Cramer-Rao Lower Bound (CRLB) for a given bit-allocation matrix and hybrid combiner. The condition for optimal ADC bit-allocation under a receiver power constraint is derived. This is derived based on the maximization of capacity with respect to bit-allocation matrix for a given channel, hybrid precoder, and hybrid combiner. …
Millimeter wave (mmWave) massive multiple-input multiple-output (massive MIMO) is one of the most promising technologies for the fifth generation and beyond wireless communication system. However, a large number of antennas incur high power consumption and hardware costs, and high-frequency communications place a heavy burden on the analog-to-digital converters (ADCs) at the base station (BS). Furthermore, it is too costly to equipping each antenna with a high-precision ADC in a large antenna array system. It is promising to adopt low-resolution ADCs to address this problem. In this paper, we …
This paper investigates an uplink multiuser massive multiple-input multiple-output (MIMO) system with one-bit analog-to-digital converters (ADCs), in which $K$ users with a single-antenna communicate with one base station (BS) with $n_r$ antennas. In this system, we propose a novel MIMO detection framework, which is inspired by coding theory. The key idea of the proposed framework is to create a non-linear code $\Cc$ of length $n_r$ and rate $K/n_r$ using the encoding function that is completely characterized by a non-linear MIMO channel matrix. From this, a multiuser MIMO detection problem is…
In this contribution, we investigate a coarsely quantized Multi-User (MU)-Multiple Input Single Output (MISO) downlink communication system, where we assume 1-Bit Digital-to-Analog Converters (DACs) at the Base Station (BS) antennas. First, we analyze the achievable sum rate lower-bound using the Bussgang decomposition. In the presence of the non-linear quanization, our analysis indicates the potential merit of reconsidering traditional signal processing techniques in coarsely quantized systems, i.e., reconsidering transmit covariance matrices whose rank is equal to the rank of the channel. Fu…
We study the maximum likelihood problem for the blind estimation of massive mmWave MIMO channels while taking into account their underlying sparse structure, the temporal shifts across antennas in the broadband regime, and ultimately one-bit quantization at the receiver. The sparsity in the angular domain is exploited as a key property to enable the unambiguous blind separation between user's channels. The main advantage of this approach is the fact that the overhead due to pilot sequences can be dramatically reduced especially when operating at low SNR per antenna. In addition, as sparsity is…
In this paper, we derive a closed-form expression for the combiner of a multiple-input-multiple-output (MIMO) receiver equipped with a minimum-mean-square-error (MMSE) estimator. We propose using variable-bit-resolution analog-to- digital converters (ADC) across radio frequency (RF) paths. The combiner designed is a function of the quantization errors across each RF path. Using very low bit resolution ADCs (1-2bits) is a popular approach with massive MIMO receiver architectures to mitigate large power demands. We show that for certain channel conditions, adopting unequal bit resolution ADCs (e…
We study a downlink multi-user multiple-input single-output (MU-MISO) system in which the base station (BS) has a large number of antennas with cost-effective one-bit digital-to-analog converters (DACs). In this system, we first identify that antenna-selection can yield a non-trivial symbol-error-rate (SER) performance gain by alleviating an error-floor problem. Likewise the previous works on one-bit precoding, finding an optimal transmit-signal vector (encompassing precoding and antenna-selection) requires exhaustive-search due to its combinatorial nature. Motivated by this, we propose a low-…
In this paper, channel estimation for millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems with one-bit analog-to-digital converters (ADCs) is considered. In the mmWave band, the number of propagation paths is small, which results in sparse virtual channels. To estimate sparse virtual channels based on the maximum a posteriori (MAP) criterion, sparsity-constrained optimization comes into play. In general, optimizing objective functions with sparsity constraints is NP-hard because of their combinatorial complexity. Furthermore, the coarse quantization of one-bit ADCs m…
Millimeter wave (mmWave) systems operating over a wide bandwidth and using a large number of antennas impose a heavy burden on power consumption. In a massive multiple-input multiple-output (MIMO) uplink, analog-to-digital con- verters (ADCs) would be the primary consumer of power in the base station receiver. This paper proposes a bit allocation (BA) method for mmWave multi-user (MU) massive MIMO systems under a power constraint. We apply ADCs to the outputs of an analog phased array for beamspace projection to exploit mmWave channel sparsity. We relax a mean square quantization error (MSQE) …
Massive multiple-input multiple-output (MIMO) can improve the overall system performance significantly. Massive MIMO systems, however, may require a large number of radio frequency (RF) chains that could cause high cost and power consumption issues. One of promising approaches to resolve these issues is using low-resolution analog-to-digital converters (ADCs) at base stations. Channel estimation becomes a difficult task by using low-resolution ADCs though. This paper addresses the channel estimation problem for massive MIMO systems using one-bit ADCs when the channels are spatially and tempora…
With bandwidths on the order of a gigahertz in emerging wireless systems, high-resolution analog-to-digital convertors (ADCs) become a power consumption bottleneck. One solution is to employ low resolution one-bit ADCs. In this paper, we analyze the flat fading multiple-input multiple-output (MIMO) channel with one-bit ADCs. Channel state information is assumed to be known at both the transmitter and receiver. For the multiple-input single-output channel, we derive the exact channel capacity. For the single-input multiple-output and MIMO channel, the capacity at infinite signal-to-noise ratio …
Internet-of-Things (IoT) refers to a high-density network of low-cost low-bitrate terminals and sensors where also low energy consumption is one central feature. As the power-budget of classical receiver chains is dominated by the high-resolution analog-to-digital converters (ADCs), there is a growing interest towards deploying receiver architectures with reduced-bit or even 1-bit ADCs. In this paper, we study waveform design, optimization and detection aspects of multi-user massive MIMO downlink where user terminals adopt very simple 1-bit ADCs with oversampling. In order to achieve spectral …
We investigate the uplink throughput achievable by a multiple-user (MU) massive multiple-input multiple-output (MIMO) system in which the base station is equipped with a large number of low-resolution analog-to-digital converters (ADCs). Our focus is on the case where neither the transmitter nor the receiver have any a priori channel state information. This implies that the fading realizations have to be learned through pilot transmission followed by channel estimation at the receiver, based on coarsely quantized observations. We propose a novel channel estimator, based on Bussgang's decomposi…
This paper investigated the uplink of multi-user massive multi-input multi-output (MIMO) systems with a mixed analog-to-digital converter (ADC) receiver architecture, in which some antennas are equipped with costly full-resolution ADCs and others with less expensive low-resolution ADCs. A closed-form approximation of the achievable spectral efficiency (SE) with the maximum-ratio combining (MRC) detector is derived. Based on this approximated result, the effects of the number of base station antennas, the transmit power, the proportion of full-resolution ADCs in the mixed-ADC structure, and the…
This paper considers uplink massive MIMO systems with 1-bit analog-to-digital converters (ADCs) and develops a deep-learning based channel estimation framework. In this framework, the prior channel estimation observations and deep neural network models are leveraged to learn the non-trivial mapping from quantized received measurements to channels. For that, we derive the sufficient length and structure of the pilot sequence to guarantee the existence of this mapping function. This leads to the interesting, and \textit{counter-intuitive}, observation that when more antennas are employed by the …
This letter considers the architecture of distributed antenna system, which is made up of a massive number of single-antenna remote radio heads (RRHs), some with full-resolution but others with low-resolution analog-to-digital converter (ADC) receivers. This architecture is greatly motivated by its high energy efficiency and low-cost implementation. We derive the worst-case uplink spectral efficiency (SE) of the system assuming a frequency-flat channel and maximum-ratio combining (MRC), and reveal that the SE increases as the number of quantization bits for the low-resolution ADCs increases, a…
The combination of orthogonal frequency modulation (OFDM) and multiple-input multiple-output (MIMO) systems plays an important role in modern communication systems. In order to meet the growing throughput demands, future MIMO-OFDM receivers are expected to utilize a massive number of antennas, operate in dynamic environments, and explore high frequency bands, while satisfying strict constraints in terms of cost, power, and size. An emerging technology to realize massive MIMO receivers of reduced cost and power consumption is based on dynamic metasurface antennas (DMAs), which inherently implem…
Department of Electrical Engineering, Princeton University（普林斯顿大学电气工程系）；Department of Electrical Engineering, POSTECH（浦项科技大学电气工程系）
The use of one-bit analog-to-digital converters (ADCs) at a receiver is a power-efficient solution for future wireless systems operating with a large signal bandwidth and/or a massive number of receive radio frequency chains. This solution, however, induces a high channel estimation error and therefore makes it difficult to perform the optimal data detection that requires perfect knowledge of likelihood functions at the receiver. In this paper, we propose a likelihood function learning method for multiple-input multiple-output (MIMO) systems with one-bit ADCs using a reinforcement learning app…
We present a novel non-linear precoding technique for the transmission of 16 quadrature amplitude modulation (QAM) symbols in a 1-bit massive multi-user (MU) multipleinput- single-output (MISO) downlink system. We deploy low resolution digital-to-analog converters (DACs) at the transmitter for the sake of decreasing the high energy consumption related to the massive MISO system. To mitigate the multi-user interference (MUI) and the distortions due to the low resolution DACs, the minimum bit error ratio (MBER) precoder was introduced in previous work. However, this precoder technique is restric…
Hybrid analog/digital architectures and receivers with low-resolution analog-to-digital converters (ADCs) are two low power solutions for wireless systems with large antenna arrays, such as millimeter wave and massive MIMO systems. Most prior work represents two extreme cases in which either a small number of RF chains with full-resolution ADCs, or low resolution ADC with a number of RF chains equal to the number of antennas is assumed. In this paper, a generalized hybrid architecture with a small number of RF chains and finite number of ADC bits is proposed. For this architecture, achievable …
