Control systems on unmanned vehicles are safety-critical systems whose requirements on reliability and safety are ever-increasing. Currently, testing a complex autonomous control system is an expensive and time-consuming process, which requires massive repeated experimental testing during the whole development stage. This paper presents a unified simulation and test platform for vehicle autonomous control systems aiming to significantly improve the development speed and safety level of unmanned vehicles. First, a unified modular modeling framework compatible with different types of vehicles is proposed with methods to ensure modeling credibility. Then, the simulation software system is developed by the model-based design framework, whose modular programming methods and automatic code generation functions ensure the efficiency, credibility, and standardization of the system development process. Finally, an FPGA-based real-time hardware-in-the-loop simulation platform is proposed to ensure the comprehensiveness and credibility of the simulation and test results. In the end, the proposed platform is applied to a multicopter control system. By comparing with experimental results, the accuracy and credibility of the simulation testing results are verified by using the simulation credibility assessment method proposed in our previous work. To verify the practicability of the proposed platform, several successful applications are presented for the multicopter rapid prototyping, estimation algorithm verification, autonomous flight testing, and automatic safety testing with automatic fault injection and result evaluation of unmanned vehicles.
The University of Manchester（曼彻斯特大学）；Cardiff University（卡迪夫大学）
In recent years, Unmanned Surface Vehicles (USV) have been extensively deployed for maritime applications. However, USV has a limited detection range with sensor installed at the same elevation with the targets. In this research, we propose a cooperative Unmanned Aerial Vehicle - Unmanned Surface Vehicle (UAV-USV) platform to improve the detection range of USV. A floatable and waterproof UAV is designed and 3D printed, which allows it to land on the sea. A catamaran USV and landing platform are also developed. To land UAV on the USV precisely in various lighting conditions, IR beacon detector …
Delft University of Technology（代尔夫特理工大学）；University of Leuven (KU Leuven)（鲁汶大学）
This paper proposes a new robust trajectory tracking error-based control approach for unmanned ground vehicles. A trajectory tracking error-based model is used to design a linear model predictive controller and its control action is combined with feedforward and robust control actions. The experimental results show that the proposed control structure is capable to let a tractor-trailer system track both linear and curvilinear target trajectories with low tracking error.
In this work, we study vulnerability of unmanned aerial vehicles (UAVs) to stealthy attacks on perception-based control. To guide our analysis, we consider two specific missions: ($i$) ground vehicle tracking (GVT), and ($ii$) vertical take-off and landing (VTOL) of a quadcopter on a moving ground vehicle. Specifically, we introduce a method to consistently attack both the sensors measurements and camera images over time, in order to cause control performance degradation (e.g., by failing the mission) while remaining stealthy (i.e., undetected by the deployed anomaly detector). Unlike existing…
Australian National University（澳大利亚国立大学）；Defence Science and Technology Group（国防科学与技术集团）
Accurate localisation of unmanned aerial vehicles is vital for the next generation of automation tasks. This paper proposes a minimum energy filter for velocity-aided pose estimation on the extended special Euclidean group. The approach taken exploits the Lie-group symmetry of the problem to combine Inertial Measurement Unit (IMU) sensor output with landmark measurements into a robust and high performance state estimate. We propose an asynchronous discrete-time implementation to fuse high bandwidth IMU with low bandwidth discrete-time landmark measurements typical of real-world scenarios. The …
The motion planning and tracking control techniques of unmanned underwater vehicles (UUV) are fundamentally significant for efficient and robust UUV navigation, which is crucial for underwater rescue, facility maintenance, marine resource exploration, aquatic recreation, etc. Studies on UUV motion planning and tracking control have been growing rapidly worldwide, which are usually sorted into the following topics: task assignment of the multi-UUV system, UUV path planning and UUV trajectory tracking. This paper provides a comprehensive review of conventional and intelligent technologies for mo…
Université de Sherbrooke（谢布鲁克大学）；University of Malaya（马来亚大学）
Recently worldwide interest is growing toward commercial, military or scientific Unmanned Surface Vehicle (USV) and hence there is required to develop their guidance, navigation, and control (GNC) systems. Real USVs are a relatively new advent, so the drawbacks of each model will be modified during the time. The proposition of an environmentally friendly as well as high efficient USV's design are the main purposes of this paper to guide future researches. Power management between renewable sources and storage units is considered. Furthermore, suitable and modern sensors are applied for state e…
University of Guelph（圭尔夫大学）；McMaster University（麦克马斯特大学）
Tracking control has been a vital research topic in robotics. This paper presents a novel hybrid control strategy for an unmanned underwater vehicle (UUV) based on a bioinspired neural dynamics model. An enhanced backstepping kinematic control strategy is first developed to avoid sharp velocity jumps and provides smooth velocity commands relative to conventional methods. Then, a novel sliding mode control is proposed, which is capable of providing smooth and continuous torque commands free from chattering. In comparative studies, the proposed combined hybrid control strategy has ensured contro…
This paper presents a data-driven optimal control policy for a micro flapping wing unmanned aerial vehicle. First, a set of optimal trajectories are computed off-line based on a geometric formulation of dynamics that captures the nonlinear coupling between the large angle flapping motion and the quasi-steady aerodynamics. Then, it is transformed into a feedback control system according to the framework of imitation learning. In particular, an additional constraint is incorporated through the learning process to enhance the stability properties of the resulting controlled dynamics. Compared wit…
The possible applications and benefits of autonomous Unmanned Aerial Vehicle (UAV) use in urban areas are gaining considerable attention. Before these possibilities can be realized, it is essential that UAVs be able to navigate reliably and precisely in urban environments. The most common means of determining the location of a UAV is to utilize position measurements from Global Navigation Satellite Systems (GNSS). In urban environments, however, GNSS measurements are significantly degraded due to occlusions and multipath. This research analyzes the use of camera Line-of-Sight (LOS) measurement…
Proper path planning is the first step of robust and efficient autonomous navigation for mobile robots. Meanwhile, it is still challenging for robots to work in a complex environment without complete prior information. This paper presents an extension to the A* search algorithm and its variants to make the path planning stable with less computational burden while handling long-distance tasks. The implemented algorithm is capable of online searching for a collision-free and smooth path when heading to the defined goal position. This paper deploys the algorithm on the autonomous drone platform a…
The hybrid electric system has good potential for unmanned tracked vehicles due to its excellent power and economy. Due to unmanned tracked vehicles have no traditional driving devices, and the driving cycle is uncertain, it brings new challenges to conventional energy management strategies. This paper proposes a novel energy management strategy for unmanned tracked vehicles based on local speed planning. The contributions are threefold. Firstly, a local speed planning algorithm is adopted for the input of driving cycle prediction to avoid the dependence of traditional vehicles on driver's ope…
In this article, a simplified modeling and system identification procedure for yaw motion of an unmanned surface vehicle (USV) is presented. Two thrusters that allow for both speed and direction control propel the USV. The outputs of the vehicle under inquiry include parameters that define the mobility of the USV in horizontal plane, such as yaw angle and yaw rate. A linear second order model is first developed, and the unknown coefficients are then determined using data from pool trials. Finally, simulations are carried out to verify the model so that it may be used in a later study to implem…
An intelligent control strategy is proposed to eliminate the actuator saturation problem that exists in the trajectory tracking process of unmanned underwater vehicles (UUV). The control strategy consists of two parts: for the kinematic modeling part, a fuzzy logic-refined backstepping control is developed to achieve control velocities within acceptable ranges and errors of small fluctuations; on the basis of the velocities deducted by the improved kinematic control, the sliding mode control (SMC) is introduced in the dynamic modeling to obtain corresponding torques and forces that should be a…
This paper investigates the cooperative control of multiple unmanned and manned vehicles via an output containment control approach for heterogeneous discrete-time multiagent systems. The unmanned vehicles act as leading vehicles to guide the manned vehicles, i.e., following vehicles. The objective is to develop a distributed output feedback control law such that the output of the following vehicles can converge to the convex hull spanned by the output of the leading vehicles exponentially. The convex hull formed by the output of the leading vehicles and the system matrix of leading vehicles a…
In this article we present a unified framework based on receding horizon techniques that can be used to design the three tasks (guidance, navigation and path-planning) which are involved in the autonomy of unmanned vehicles. This tasks are solved using model predictive control and moving horizon estimation techniques, which allows us to include physical and dynamical constraints at the design stage, thus leading to optimal and feasible results. In order to demonstrate the capabilities of the proposed framework, we have used Gazebo simulator in order to drive a Jackal unmanned ground vehicle (U…
In this paper, a new unmanned aerial vehicle (UAV) structure, referred to as swash mass UAV, is presented. It consists of a double blade coaxial shaft rotor and four swash masses that allow changing the orientation and maneuvering the UAV. The dynamical system model is derived from the Newton\textquotesingle s law framework. The rotational behavior of the UAV is discussed as a function of the design parameters. Given the uniqueness and the form of the obtained non-linear dynamical system model, a back-stepping control mechanism is proposed. It is obtained following the Lyapunov's control appro…
Connectivity between ground vehicles can be utilized and expanded to include aerial vehicles for coordinated missions. Using Vehicle-to-Everything (V2X) communication technologies, a communication link can be established between Connected and Autonomous vehicles (CAVs) and Unmanned Aerial vehicles (UAVs). Hardware implementation and testing of a ground to air communication link is crucial for real-life applications. Two different communication links were established, Dedicated Short Range communication (DSRC) and 4G internet based WebSocket communication. Both links were tested separately both…
A system of cooperative unmanned aerial vehicles (UAVs) is a group of agents interacting with each other and the surrounding environment to achieve a specific task. In contrast with a single UAV, UAV swarms are expected to benefit efficiency, flexibility, accuracy, robustness, and reliability. However, the provision of external communications potentially exposes them to an additional layer of faults, failures, uncertainties, and cyber-attacks and can contribute to the propagation of error from one component to other components in a network. Also, other challenges such as complex nonlinear dyna…
A control system verification framework is presented for unmanned aerial vehicles using theorem proving. The framework's aim is to set out a procedure for proving that the mathematically designed control system of the aircraft satisfies robustness requirements to ensure safe performance under varying environmental conditions. Extensive mathematical derivations, which have formerly been carried out manually, are checked for their correctness on a computer. To illustrate the proceedures, a higher-order logic interactive theorem-prover and an automated theorem-prover are utilized to formally veri…
Future unmanned aerial vehicles (drones) will be shared by multiple users and will have to operate in conditions where their fully-autonomous function is required. Calculation of a drones trajectory will be important but optimal trajectories cannot be calculated unless mass and flight speed are taken into account. This article presents the case for on-drone trajectory planning in a multi-user dynamic payload mass scenario, allowing a drone to calculate its trajectory with no need for ground control communication. We formulate and investigate on-drone trajectory planning under variable payload …
This paper presents a new Lyapunov-based nonlinear model predictive controller (LNMPC) for the attitude control problem of unmanned aerial vehicles (UAVs), which is essential for their functioning operation. The controller is designed based on a quadratic cost function integrating UAV dynamics and system constraints. An additional contraction constraint is then introduced to ensure closed-loop system stability. That constraint is fulfilled via a Lyapunov function derived from a sliding mode controller (SMC). The feasibility and stability of the LNMPC are finally proved. Simulation and comparis…
Aeronautical Mobile Airport Communications System (AeroMACS) is based on the IEEE 802.16e mobile wireless standard commonly known as WiMAX. It is expected to be the main part of the next-generation aviation communication system to support fixed and mobile services for manned and unmanned applications. AeroMACS will be an essential technology helping pave the way toward full integration of Unmanned Aircraft Vehicle (UAV) into the national airspace. A number of practical tests and analyses have been done so far for AeroMACS. The main contribution of this paper is to consider the theoretical conc…
This paper proposes a novel parametric identification approach for linear systems using Deep Learning (DL) and the Modified Relay Feedback Test (MRFT). The proposed methodology utilizes MRFT to reveal distinguishing frequencies about an unknown process; which are then passed to a trained DL model to identify the underlying process parameters. The presented approach guarantees stability and performance in the identification and control phases respectively, and requires few seconds of observation data to infer the dynamic system parameters. Quadrotor Unmanned Aerial Vehicle (UAV) attitude and al…
An innovative method of detecting Unmanned Aerial Vehicles (UAVs) is presented. The goal of this study is to develop a robust setup for an autonomous multi-rotor hunter UAV, capable of visually detecting and tracking the intruder UAVs for real-time motion planning. The system consists of two parts: object detection using a stereo camera to generate 3D point cloud data and video tracking applying a Kalman filter for UAV motion modeling. After detection, the hunter can aim and shoot a tethered net at the intruder to neutralize it. The computer vision, motion tracking, and planning algorithms can…
This article introduces a new mobile-based application of modern information and communication technology in agriculture based on Internet of Things (IoT), embedded systems and an unmanned aerial vehicle (UAV). The proposed agricultural monitoring system was designed and implemented using Arduino microcontroller boards, Wi-Fi modules, water pumps and electronic environmental sensors, namely temperature, humidity and soil moisture. The role of UAV in this study is to collect these environmental data from different regions of the farm. Then, the quantity of water irrigation is automatically comp…
