Waves that are perfectly confined in the continuous spectrum of radiating waves without interaction with them are known as bound states in the continuum (BICs). Despite recent discoveries of BICs in nanophotonics, full routing and control of BICs are yet to be explored. Here, we experimentally demonstrate BICs in a fundamentally new photonic architecture by patterning a low-refractive-index material on a high-refractive-index substrate, where dissipation to the substrate continuum is eliminated by engineering the geometric parameters. Pivotal BIC-based photonic components are demonstrated, including waveguides, microcavities, directional couplers, and modulators. Therefore, this work presents the critical step of photonic integrated circuits in the continuum, and enables the exploration of new single-crystal materials on an integrated photonic platform without the fabrication challenges of patterning the single-crystal materials. The demonstrated lithium niobate platform will facilitate development of functional photonic integrated circuits for optical communications, nonlinear optics at the single photon level as well as scalable photonic quantum information processors.
This paper demonstrates the operation of a universal RF photonic circuit that consists of a generalized Mach Zehnder Interferometer architecture with its Nx1 combiner replaced by a NxN optical DFT network. The proposed circuit architecture can be used for SSB modulation, frequency up-conversion/down-conversion, frequency multiplication and phase correlated subcarrier generation based on the choice of output ports and dimension (N) of the circuit. An alternative representation of the circuit is also reported with the aim of a systematic demultiplexing. A transfer matrix approach is used to deve…
A novel technique is presented for realising programmable silicon photonic circuits. Once the proposed photonic circuit is programmed, its routing is retained without the need for additional power consumption. This technology enables a uniform multi-purpose design of photonic chips for a range of different applications and performance requirements, as it can be programmed for each specific application after chip fabrication. Therefore the cost per chip can be dramatically reduced because of the increase in production volume, and rapid prototyping of new photonic circuits is enabled. Essential …
Erbium-doped fiber amplifiers have revolutionized long-haul optical communications and laser technology. Erbium ions could equally provide a basis for efficient optical amplification in photonic integrated circuits. However, this approach has thus far remained impractical due to insufficient output power. Here, we demonstrate a photonic integrated circuit based erbium amplifier reaching 145 mW output power and more than 30 dB small-signal gain -- on par with commercial fiber amplifiers and beyond state-of-the-art III-V heterogeneously integrated semiconductor amplifiers. We achieve this by app…
Quantum-dot (QD) nanolasers integrated on a silicon photonic circuit are demonstrated for the first time. QD nanolasers based on one-dimensional photonic crystal nanocavities containing InAs/GaAs QDs are integrated on CMOS-processed silicon waveguides cladded by silicon dioxide. We employed transfer-printing, whereby the three-dimensional stack of photonic nanostructures is assembled in a simple pick-and-place manner. Lasing operation and waveguide-coupling of an assembled single nanolaser are confirmed through micro-photoluminescence spectroscopy. Furthermore, by repetitive transfer-printing,…
Chiral light matter interaction enables new fundamental researches and applications of light. The interaction has traditionally faced challenges in low directionality and efficiency based on spin orbit interaction of light in microscopic waveguides. It is pivotal to exploit photonic integrated circuits to efficiently engineer photonic chiral behavior. Here, we present ultra directional high efficient chiral coupling in silicon photonic circuits based on low order to high order mode conversion and interference. We show that the directionality of chiral coupling, in principle, can approach minus…
Efficient coupling of III-V light sources to silicon photonic circuits is one of the key challenges of integrated optics. Important requirements are low coupling losses, as well as small footprint and high yield of the overall assembly, along with the ability to use automated processes for large-scale production. In this paper, we demonstrate that photonic wire bonding addresses these challenges by exploiting direct-write two-photon lithography for in-situ fabrication of three-dimensional freeform waveguides between optical chips. In a series proof-of-concept experiments, we connect InP-based …
Thin-film lithium niobate (LN) photonic integrated circuits (PICs) could enable ultrahigh performance in electro-optic and nonlinear optical devices. To date, realizations have been limited to chip-scale proof-of-concepts. Here we demonstrate monolithic LN PICs fabricated on 4- and 6-inch wafers with deep ultraviolet lithography and show smooth and uniform etching, achieving 0.27 dB/cm optical propagation loss on wafer-scale. Our results show that LN PICs are fundamentally scalable and can be highly cost-effective.
Integrated lithium niobate (LN) photonic circuits have recently emerged as a promising candidate for advanced photonic functions such as high-speed modulation, nonlinear frequency conversion and frequency comb generation. For practical applications, optical interfaces that feature low fiber-to-chip coupling losses are essential. So far, the fiber-to-chip loss (commonly > 10 dB) dominates the total insertion losses of typical LN photonic integrated circuits, where on-chip propagation losses can be as low as 0.03 - 0.1 dB/cm. Here we experimentally demonstrate a low-loss mode size converter for …
We demonstrate that the integration of a phase-change material (PCM) in one of the two microresonators of a photonic metamolecule, coupled to a bus waveguide, can lead to unidirectional Fano resonances and to the emergence of a unidirectional transmission window. The phase change is caused by light-induced heating and is accompanied by an abrupt increase in the extinction coefficient of the PCM resonator. Due to the photonic circuit asymmetry, the critical value of the input light intensity triggering the phase change is strongly dependent on the input light direction. The latter determines th…
Valley pseudospin, a new degree of freedom in photonic lattices, provides an intriguing way to manipulate photons and enhance the robustness of optical networks. Here we experimentally demonstrated topological waveguiding, refracting, resonating, and routing of valley-polarized photons in integrated circuits. Specifically, we show that at the domain wall between photonic crystals of different topological valley phases, there exists a topologically protected valley kink state that is backscattering-free at sharp bends and terminals. We further harnessed these valley kink states for constructing…
Integration of superconducting nanowire single photon detectors and quantum sources with photonic waveguides is crucial for realizing advanced quantum integrated circuits. However, scalability is hindered by stringent requirements on high performance detectors. Here we overcome the yield limitation by controlled coupling of photonic channels to pre-selected detectors based on measuring critical current, timing resolution, and detection efficiency. As a proof of concept of our approach, we demonstrate a hybrid on-chip full-transceiver consisting of a deterministically integrated detector couple…
Solving mathematical equations faster and more efficiently has been a Holy Grail for centuries for scientists and engineers across all disciplines. While electronic digital circuits have revolutionized equation solving in recent decades, it has become apparent that performance gains from brute-force approaches of compute-solvers are quickly saturating over time. Instead, paradigms that leverage the universes natural tendency to minimize a systems free energy, such as annealers or Ising Machines, are being sought after due to favorable complexity scaling. Here we introduce a programmable analog…
Photonic nanostructures simultaneously maximizing spectral and spatial overlap between fundamental and second-harmonic confined modes are highly desirable for enhancing second-order nonlinear effects in nonlinear media. These conditions have thus far remained challenging to satisfy in photonic crystal cavities because of the difficulty in designing a band gap at the second-harmonic frequency. Here, we solve this issue by using instead a bound state in the continuum at that frequency, and we design a doubly-resonant photonic crystal slab cavity with strongly improved figures of merit for nonlin…
The field of microelectromechanical Systems (MEMS) for photonic integrated circuits (PICs) is reviewed. This field leverages mechanics at the nanometer to micrometer scale to improve existing components and introduce novel functionalities in PICs. This review covers the MEMS actuation principles and the mechanical tuning mechanisms for integrated photonics. The state of the art of MEMS tunable components in PICs is quantitatively reviewed and critically assessed with respect to suitability for large-scale integration in existing PIC technology platforms. MEMS provide a powerful approach to ove…
The ability of photonic crystal waveguides (PCWs) to confine and slow down light makes them an ideal component to enhance the performance of various photonic devices, such as optical modulators or sensors. However, the integration of PCWs in photonic applications poses design challenges, most notably, engineering the PCW mode dispersion and creating efficient coupling devices. Here, we solve these challenges with photonic inverse design, and experimentally demonstrate a slow-light PCW optical phased array (OPA) with a wide steering range. Even and odd mode PCWs are engineered for a group index…
On-chip microlaser sources in the blue constitute an important building block for complex integrated photonic circuits on silicon. We have developed photonic circuits operating in the blue spectral range based on microdisks and bus waveguides in III-nitride on silicon. We report on the interplay between microdisk-waveguide coupling and its optical properties. We observe critical coupling and phase matching, i.e. the most efficient energy transfer scheme, for very short gap sizes and thin waveguides (g = 45 nm and w = 170 nm) in the spontaneous emission regime. Whispering gallery mode lasing is…
Photonic integration, advanced functionality, reconfigurability, and high RF performance are key features in integrated microwave photonic systems that are still difficult to achieve simultaneously. In this work, we demonstrate an integrated microwave photonic circuit that can be reconfigured for two distinct RF functions, namely, a tunable notch filter and a phase shifter. We achieved $>$50dB high-extinction notch filtering over 6-16 GHz and 2$π$ continuously tunable phase shifting over 12-20 GHz frequencies. At the same time, we implemented an on-chip linearization technique to achieve a spu…
We report a compact, scalable, quantum photonic integrated circuit realised by combining multiple, independent InGaAs/GaAs quantum-light-emitting-diodes (QLEDs) with a silicon oxynitride waveguide circuit. Each waveguide joining the circuit can then be excited by a separate, independently electrically contacted QLED. We show that the emission from neighbouring QLEDs can be independently tuned to degeneracy using the Stark Effect and that the resulting photon streams are indistinguishable. This enables on-chip Hong-Ou-Mandel-type interference, as required for many photonic quantum information p…
We develop a thermally tunable hybrid photonic platform comprising gallium arsenide (GaAs) photonic crystal cavities, silicon nitride (SiN$_x$) grating couplers and waveguides, and chromium (Cr) microheaters on an integrated photonic chip. The GaAs photonic crystal cavities are evanescently connected to a common bus waveguide, separating the computation and communication layers. The microheaters are designed to continuously and reversibly tune distant photonic crystal cavities to a common resonance. This architecture can be implemented in a coherent optical network for dedicated optical comput…
Microwave photonics (MWP) studies the interaction between microwave and optical waves for the generation, transmission and processing of microwave signals (i.e., three key domains), taking advantages of broad bandwidth and low loss offered by modern photonics. Integrated MWP using photonic integrated circuits (PICs) can reach a compact, reliable and green implementation. Most PICs, however, are recently developed to perform one or more functions restricted inside a single domain. In this paper, as highly desired, a multifunctional PIC is proposed to cover the three key domains. The PIC is fabr…
The spectacular success of silicon-based photonic integrated circuits (PICs) in the past decade naturally begs the question of whether similar fabrication procedures can be applied to other material platforms with more desirable optical properties. In this work, we demonstrate the individual passive components (grating couplers, waveguides, multi-mode interferometers and ring resonators) necessary for building large scale integrated circuits in suspended gallium arsenide (GaAs). Implementing PICs in suspended GaAs is a viable route towards achieving optimal system performance in areas with str…
A photonic integrated circuit (PIC) comprised of an 11 cm multimode speckle waveguide, a 1x32 splitter, and a linear grating coupler array is fabricated and utilized to receive 2 GHz of radio-frequency (RF) signal bandwidth from 2.5 to 4.5 GHz using compressive sensing (CS). Incoming RF signals are modulated onto chirped optical pulses which are input to the multimode waveguide. The multimode waveguide produces the random projections needed for CS via optical speckle. The time-varying phase and amplitude of two test RF signals between 2.5 and 4.5 GHz are successfully recovered using the standa…
The growing diffusion of integrated photonic technologies requires fast and non-invasive quality control techniques for mass-production. We present a general diagnostic technique for sub-ps imaging of photonic circuits combining wide-field optical microscopy and optical gating. The simultaneous access to multiple parameters of a photonic structure enables an unprecedented characterization of its functional design as opposed to typical single-domain techniques such as frequency or time domain reflectometry and near-field microscopy. The non-contact and non-perturbative nature of the technique m…
Valley degrees of freedom, providing a novel way to increase capacity and efficiency of information processing, have become an important instrument for photonics. Experimental studies on photonic topological valley kink states at interfaces between regions with opposite valley-Chern numbers have attracted much attention, however, were restricted to zigzag-type interfaces, largely limiting their applications such as geometry-dependent topological channel intersections. Here, we experimentally demonstrate and manipulate valley kink states at generic interfaces in subwavelength substrate-integrat…
Transient fully reconfigurable photonic circuits can be introduced at the optical fiber surface with subangstrom precision. A building block of these circuits, a 0.7 angstrom-precise nano-bottle resonator, is experimentally created by local heating, translated, and annihilated.
In the paper, we propose the new technology for mass production of the photonic crystal devices and all-optical integrated circuits. We carry out the brief analysis of positive and negative sides paying attention to recent advances in silicon fibers fabrication which is crucial moment in the proposed technology.
Femtosecond laser writing is a powerful technique that allows rapid and cost-effective fabrication of photonic integrated circuits with unique three-dimensional geometries. In particular, the possibility to reconfigure such devices by thermo-optic phase shifters represents a paramount feature, exploited to produce adaptive and programmable circuits. However, the scalability is strongly limited by the flaws of current thermal phase shifters, which require hundreds of milliwatts to operate and exhibit large thermal crosstalk. In this work, thermally-insulating three-dimensional microstructures a…
We investigate the formation of photonic bound states in the continuum (BICs) in photonic crystal slabs from an analytical perspective. Unlike the stationary at-$Γ$ BICs which origin from the geometric symmetry, the tunable off-$Γ$ BICs are due to the weighted destructive via-the-continuum interference in the vicinity of accidental symmetry when the majority of the radiation is pre-canceled. The symmetric compatible nature of the off-$Γ$ BICs leads to a trapping of light that can be tuned through continuously varying the wavevector. With the analytical approach, we explain a reported experimen…
Photonic integrated circuits (PICs) are today acknowledged as an effective solution to fulfill the demanding requirements of many practical applications in both classical and quantum optics. Phase shifters integrated in the photonic circuit offer the possibility to dynamically reconfigure its properties in order to fine tune its operation or to produce adaptive circuits, thus greatly extending the quality and the applicability of these devices. In this paper, we provide a thorough discussion of the main problems that one can encounter when using thermal shifters to reconfigure photonic circuit…
There has been a recent surge of interest in the implementation of linear operations such as matrix multipications using photonic integrated circuit technology. However, these approaches require an efficient and flexible way to perform nonlinear operations in the photonic domain. We have fabricated an optoelectronic nonlinear device--a laser neuron--that uses excitable laser dynamics to achieve biologically-inspired spiking behavior. We demonstrate functionality with simultaneous excitation, inhibition, and summation across multiple wavelengths. We also demonstrate cascadability and compatibil…
An anisotropic photonic crystal containing two anisotropic defect layers is considered. It is demonstrated that the system under can support a Fabry-Perot bound state in the continuum (FP-BIC). A fully analytic solution of the scattering problem as well as a condition for FP-BIC have been derived in the framework of the temporal coupled-mode theory.
We suggest a novel conceptual approach for describing the properties of waveguides and circuits in photonic crystals, based on the effective discrete equations that include the long-range interaction effects. We demonstrate, on the example of sharp waveguide bends, that our approach is very effective and accurate for the study of bound states and transmission spectra of the photonic-crystal circuits, and disclose the importance of evanescent modes in their properties.
We demonstrate a photonic circuit with integrated long-lived quantum memories. Pre-selected quantum nodes - diamond micro-waveguides containing single, stable, and negatively charged nitrogen vacancy centers - are deterministically integrated into low-loss silicon nitride waveguides. Each quantum memory node efficiently couples into the single-mode waveguide (> 1 Mcps collected into the waveguide) and exhibits long spin coherence times of up to 120 μs. Our system facilitates the assembly of multiple quantum memories into a photonic integrated circuit with near unity yield, paving the way towar…
A new conception of the wavelength division multiplexing on the basis of the two-dimensional photonic crystal was developed. The photonic crystals band structures were investigated in details. The method for the synthesis of the two-channel wavelength division multiplexer on the basis of two dimensional photonic crystals was developed using this method the device was synthesized. The spectral characteristics of the device and its dynamic pulse pattern response were investigated.
