Ferroelectric perovskite oxides possess a large electrocaloric (EC) effect, but usually at high temperatures near the ferroelectric/paraelectric phase transition temperature, which limits their potential application as next-generation solid-state cooling devices. We use classical molecular dynamics to study the electric field induced phase transitions and EC effect in PMN-PT (PbMg1/3Nb2/3O3-PbTiO3). We find that the maximum EC strength of PMN-PT occurs within the morphotropic phase boundary (MPB) region at 300 K. The large adiabatic temperature change is caused by easy rotation of polarization within the MPB region.
Over the past decades, there has been significant interest in new cooling technology based on the electrocaloric effect. The large electrocaloric effect observed in polymeric and inorganic ferroelectric materials made possible development of dielectric cooling devices of a new generation. We report a significant impact of annealing on the electrocaloric effect observed in 12/65/35 PLZT bulk ceramics. The electrocaloric data were obtained by direct measurements. Electrocaloric results confirm the existence of the significant electrocaloric response in this relaxor ferroelectric PLZT composition…
The electrocaloric (EC) effect is calculated for Gd-substituted PMN (x = 0 to 0.1) relaxors from temperature dependent heat capacity and polarization measurements, using a thermodynamic Maxwell equation. Polarization change with temperature reveals an anomalous behaviour around the glass transition temperature, which is in the vicinity of a crossover from positive to negative EC effect, which is explained evoking the critical slowing-down of the polar nano-domains dynamics to super-dipolar glass state upon cooling. The maximum negative EC coefficient is observed to decrease from 0.4 K-mm/kV at…
Electrically driven adiabatic changes of temperature are identified in the archetypal electrocaloric material PbSc0.5Ta0.5O3 by comparing isothermal changes of electrical polarization due to slow variation of electric field, and adiabatic changes of electrical polarization due to fast variation of electric field. By obtaining isothermal (adiabatic) electrical polarization data at measurement (starting) temperatures separated by <0.4 K, we identify a maximum temperature change of ~2 K due to a maximum field change of 26 kV cm-1, for starting temperatures in the range 300 - 315 K. These quasi in…
The electrocaloric effect of BaTiO3 multilayer thick film structure was investigated by direct measurement and theoretical calculation. The samples were prepared by the tape-casting method, which had 180 dielectric layers with an average thickness of 1.4μm. The thermodynamic calculation based on the polarization- temperature curves predicted a peak heat adsorption of 0.32J/g at 80^\circC under 176kV/cm electric field. The direct measurement via differential scanning calorimeter showed a much higher electrocaloric effect of 0.91J/g at 80^\circC under same electric field. The difference could re…
An atomistic effective Hamiltonian is used to investigate electrocaloric (EC) effects of Pb(Mg$_{1/3}$Nb$_{2/3}$)O$_{3}$ (PMN) relaxor ferroelectrics in its ergodic regime, and subject to electric fields applied along the pseudocubic [111] direction. Such Hamiltonian qualitatively reproduces (i) the electric field-versus-temperature phase diagram, including the existence of a critical point where first-order and second-order transitions meet each other; and (ii) a giant EC response near such critical point. It also reveals that such giant response around this critical point is microscopically …
We analyse the effects of applying an electric field on the critical temperature, Ts, at which superionicity appears in archetypal fast ion conductor CaF2 by means of molecular dynamics simulations. We find that the onset of superionicity can be reduced by about 100K when relatively small electric fields of ~50KV/cm are employed. Under large enough electric fields, however, ionic conductivity is depleted. The normal to superionic phase transition is characterised by a large increase of entropy, thereby sizeable electrocaloric effects can be realised in fast ion conductors that are promising fo…
In this study, we report on a direct measurement method for the electrocaloric effect, the heating/cooling upon application/removal of an electric field in dielectric materials, based on a lock-in thermography technique. By use of sinusoidal excitation and multi-harmonic detection, the actual temperature change can be measured by a single measurement in the frequency domain even when the electrocaloric effect shows nonlinear response to the excitation field. We have demonstrated the method by measuring the temperature dependence of the electric-field-induced temperature change for two Sr-doped…
We study the electrocaloric effect in the classic ferroelectric BaTiO3 through a series of phase transitions driven by applied electric field and temperature. We find both negative and positive electrocaloric effects, with the negative electrocaloric effect, where temperature decreases with applied field, in monoclinic phases. Macroscopic polarization rotation is evident through the monoclinic and orthorhombic phases under applied field, and is responsible for the negative electrocaloric effect.
The perovskite crystal BaTiO3 is modeled using a first-principles based effective Hamiltonian and molecular dynamics simulations are performed to estimate the pyroelectric response. The electrocaloric temperature change, \DeltaT, is calculated for different temperatures and externally applied electric fields. It is found that it is possible to achieve a large \DeltaT, around 5-6 K, for a relatively small electric field gradient, less than 100 kV/cm, if the applied fields have a small absolute magnitude.
Electrically driven thermal changes in PbSc0.5Ta0.5O3 bulk ceramics are investigated using temperature and electric-field dependent differential scanning calorimetry and infrared thermometry. On first application and removal of electric field, we find asymmetries in the magnitude of isothermal entropy change $Δ$ S and adiabatic temperature change $Δ$ T, due to hysteresis. On subsequent field cycling, we find further asymmetries in the magnitude of $Δ$ T due to non-linearity in the isofield legs of entropy-temperature plots.
Refrigeration systems based on compression of greenhouse gases are environmentally threatening and cannot be scaled down to on-chip dimensions. In the vicinity of a phase transition caloric materials present large thermal responses to external fields, which makes them promising for developing alternative solid-state cooling devices. Electrocaloric effects are particularly well-suited for portable refrigeration applications; however, most electrocaloric materials operate best at non-ambient temperatures or require the application of large electric fields. Here, we predict that modest electric f…
An applied electric field can reversibly change the temperature of an electrocaloric material under adiabatic conditions, and the effect is strongest near phase transitions. This phenomenon has been largely ignored because only small effects (0.003 K V^-1) have been seen in bulk samples such as Pb0.99Nb0.02(Zr0.75Sn0.20Ti0.05)0.98O3 and there is no consensus on macroscopic models. Here we demonstrate a giant electrocaloric effect (0.48 K V^-1) in 300 nm sol-gel PbZr0.95Ti0.05O3 films near the ferroelectric Curie temperature of 222oC. We also discuss a solid state device concept for electrical …
We use molecular dynamics with a first-principles-based shell model potential to study the electrocaloric effect (ECE) in lithium niobate, LiNbO$_3$, and find a giant electrocaloric effect along a line passing through the ferroelectric transition. With applied electric field, a line of maximum ECE passes through the zero field ferroelectric transition, continuing along a Widom line at high temperatures with increasing field, and along the instability that leads to homogeneous ferroelectric switching below $T_c$ with an applied field antiparallel to the spontaneous polarization. This line is de…
An improved thermodynamic cycle is proposed, where the cooling effect of an electrocaloric refrigerant is enhanced by applying a reversed electric field. In contrast to conventional adiabatic heating or cooling by on-off cycles of the external electric field, applying a reversed field is significantly improving the cooling efficiency, since the variation in configurational entropy is increased. By comparing results from computer simulations using Monte-Carlo algorithms and experiments using direct electrocaloric measurements, we show that the electrocaloric cooling efficiency can be enhanced b…
There is a surge of interest in developing environmentally friendly cooling technology based on the solid--state electrocaloric effect (ECE). Here, we point out that negative ECE with a fast cooling rate ($\approx$10$^{11}$ K/s) can be achieved by driving solid crystals to a high--temperature phase with a properly designed electric field pulse. Specifically, we predict that an ultrafast electric field pulse can cause a negative ECE up to 35 K in PbTiO$_3$ occurring on few picosecond time scales. We acquire and analyze these results by clarifying the mechanism of ECE during an adiabatic irrever…
The electrocaloric effect (ECE) in BaTiO3 is simulated using two different first-principles based effective Hamiltonian molecular dynamics methods. The calculations are performed for a wide range of temperatures (30--900 K) and external electric fields (0--500 kV/cm). As expected, a large adiabatic temperature change, Delta-T, at the Curie temperature, T_C, is observed. It is found that for single crystals of pure BaTiO3, the temperature range where a large Delta-T is observed is narrow for small external electric fields (<50 kV/cm). Large fields (>100 kV/cm) may be required to broaden the eff…
Anomalous electrocaloric effect (ECE) with decreasing temperature upon application of an electric field is known to occur in antiferroelectrics (AFEs), and previous understanding refers to the field-induced canting of electric dipoles if there is no phase transitions. Here, we use a first-principle-based method to study the ECE in Nd-substituted BiFeO3 (BNFO) perovskite solid solutions, which has the Pnma-type AFE ground state. We demonstrate another scenario to achieve and explain anomalous ECE, emphasizing that explicit consideration of octahedral tiltings is indispensable for a correct unde…
We use molecular dynamics simulations for a first principles-based effective Hamiltonian to calculate two important quantities characterizing the electrocaloric effect in BaTiO$_3$, the adiabatic temperature change $ΔT$ and the isothermal entropy change $ΔS$, for different electric field strengths. We compare direct and indirect methods to obtain $ΔT$ and $ΔS$, and we confirm that both methods indeed lead to identical result provided that the system does not actually undergo a first order phase transition. We also show that a large electrocaloric response is obtained for electric fields beyond…
The proton ordering model for the KH$_{2}$PO$_{4}$ type ferroelectrics is modified by taking into account non-linear effects, namely, the dependence of the effective dipole moments on the proton ordering parameter. Within the four-particle cluster approximation we calculate the crystal polarization, longitudinal dielectric permittivity, specific heat, and explore the electrocaloric effect. Smearing of the ferroelectric phase transition by the longitudinal electric field is described. A good agreement with experiment is obtained.
Physical nature of "giant" magnetocaloric and electrocaloric effects, MCE and ECE, is explained in terms of the new fundamentals of phase transitions, ferromagnetism and ferroelectricity. It is the latent heat of structural (nucleation-and-growth) phase transitions from a normal crystal state to the orientation-disordered crystal (ODC) state where the constituent particles are engaged in thermal rotation. The ferromagnetism or ferroelectricity of the material provides the capability to trigger the structural phase transition by application, accordingly, of magnetic or electric field.
Giant electrocaloric (EC) effect is observed in BaTiO3 multilayer thick film structure. The temperature change is as high as 4.0 oC under an applied electric field of 352 kV/cm. Most importantly, the EC effect is found to depend on the varying rate of the applied field. Based on the giant net cooling (~0.37 J/g) resulting from the difference in the varying rates of rising and falling fields, the kinetic EC effect provides an effective solution for the design of refrigeration cycle in ferroelectric micro-refrigerator.
The proton ordering model for the KH$_{2}$PO$_{4}$ type ferroelectrics is modified by taking into account the dependence of the effective dipole moments on the proton ordering parameter. Within the four-particle cluster approximation we calculate the crystal polarization and explore the electrocaloric effect. Smearing of the ferroelectric phase transition by a longitudinal electric field is described. A good agreement with experiment is obtained.
The existence and feasibility of the multicaloric, polycrystalline material 0.8Pb(Fe1/2Nb1/2)O3-0.2Pb(Mg1/2W1/2)O3, exhibiting magnetocaloric and electrocaloric properties, are demonstrated. Both the electrocaloric and magnetocaloric effects are observed over a broad temperature range below room temperature. The maximum magnetocaloric temperature change of ~0.26 K is obtained with a magnetic-field amplitude of 70 kOe at a temperature of 5 K, while the maximum electrocaloric temperature change of ~0.25 K is obtained with an electric-field amplitude of 60 kV/cm at a temperature of 180 K. The mat…
Using the previously developed model we study the electrocaloric effect (ECE) in antiferroelectric crystals of squaric acid. At low temperatures, the polarization reorientation by the electric field applied along the crystallographic $a$ axis of these crystals is predicted to be a two-stage process, with one of the sublattice polarizations switched twice, by 90$^\circ$ each time. The $T$-$E$ landscapes of the model polarization and entropy are explored. The ECE, characterized by the introduced electric Grüneisen parameter, is found to be negative in the antiferroelectric phase. In the intermed…
Recent findings of a large electrocaloric (EC) effect in polymeric and inorganic ferroelectric materials open a potential possibility of development of solid-state cooling or heating devices of new generation with better energy efficiency that may be less harmful for the environment. We investigate by using direct measurements, the temperature and electric field dependence of the electrocaloric response in Pb1-xLax(ZryTi1-y)1-x/4O3 bulk ceramics (PLZT) with x=0.06 and 0.12. Here, the properties of the EC response were probed in a part of the PLZT composition phase diagram with low y=0.40 compo…
We have investigated the coupling of lattice with spin via strain interactions in the CoFe2O4/PMN-PT composite system. X-ray diffraction and Raman spectroscopic studies illustrate a remarkable modification in CoFe2O4lattice across Curie temperature (450 K) of PMN-PT. Subsequently, CoFe2O4/PMN-PT composite reveals a sudden drop in magnetic moment across Tc of PMN-PT (450 K). However,theindependent CoFe2O4phasedisplaystypical ferromagnetic behaviour across this temperature. These findings establish spin-lattice coupling owing to th interfacial strain transfer between CoFe2O4 and PMN-PT in compos…
The present letter explores the electrocaloric effect (ECE) in the lead free oxide Ba0.8Ca0.2Ti0.95Ge0.05O3 ceramics (BCTG). The electrocaloric responsivity (dT/dE) was determined by two different methods using the Maxwell relationship (dT/dE)~(dP/dT)_E. In a first well-known indirect method, P-E hysteresis loops were measured in a wide temperature range from which the pyroelectric coefficient p_E=(dP/dT)_E and thus (dT/dE) were determined by derivation of P(T,E) data. In the second novel method the pyroelectric coefficient p_E and consequently the electrocaloric responsivity was determined by…
We show that the electrocaloric (EC) effect -- e.g., the temperature change experienced by an insulator upon application of an electric bias -- lends itself to a straightforward interpretation when expressed as a Taylor series in the external field. Our formalism explains in a unified and simple way the most notable small-field effects reported the literature -- e.g., the so-called {\em normal} (increase of temperature under bias, as usually found in ferroelectrics) and {\em inverse} (decrease of temperature, as e.g. in antiferroelectrics) EC responses -- and clarifies their physical interpret…
To investigate the caloric effects in the CsH$_2$PO$_4$ ferroelectric, a modified pseudospin model of this crystal is used, which takes into account the dependence of the parameters of interaction between pseudospins on lattice strains. The model also takes into account the dependence of the effective dipole moment of a pseudospin on the order parameter. In the two-particle cluster approximation, the influence of the longitudinal electric field and hydrostatic pressure on the molar entropy of the crystal was studied. The electrocaloric and barocaloric effects were studied. The calculated elect…
An atomistic effective Hamiltonian is used to compute electrocaloric (EC) effects in rare-earth substituted BiFeO$_{3}$ multiferroics. A phenomenological model is then developed to interpret these computations, with this model indicating that the EC coefficient is the sum of two terms, that involve electric quantities (polarization, dielectric response), the antiferromagnetic order parameter, and the coupling between polarization and antiferromagnetic order. The first one depends on the polarization and dielectric susceptibility, has the analytical form previously demonstrated for ferroelectri…
We present a comprehensive theoretical and experimental study of voltage-controlled standing spin waves resonance (SSWR) in PMN-PT/NiFe multiferroic heterostructures patterned into microstrips. A spin-diode technique was used to observe ferromagnetic resonance (FMR) mode and SSWR in NiFe strip mechanically coupled with a piezoelectric substrate. Application of an electric field to a PMNPT creates a strain in permalloy and thus shifts the FMR and SSWR fields due to the magnetostriction effect. The experimental results are compared with micromagnetic simulations and a good agreement between them…
By using the semi-wet synthesis method, lead-free ferroelectric materials Ba0.9Sr0.1Ti1-xSnxO3 with x = 0, 0.02, 0.05, and 0.10 (abbreviated as BSTS) were prepared and their structural, electric and electrocaloric properties were investigated. The X-ray diffraction (XRD) patterns show that the samples calcined at 950°C have well crystallized into perovskite structure suggesting the substitution of Ti4+ by Sn4+ in BST lattice. With increasing content of Sn, the enhancement of the dielectric permittivity was observed for (0<x<0.05) and the ferroelectric transition temperature (TC) was found to s…
In acceptor doped ferroelectrics and in ferroelectric films and nanocomposites, defect dipoles, strain gradients, and the electric boundary conditions at interfaces and surfaces often impose internal bias fields. In this work we delicately study the impact of internal bias fields on the electrocaloric effect (ECE), utilizing an analytical model and \emph{ab initio}-based molecular dynamics simulations. We reveal the complex dependency of the ECE on field protocol and relative strength of internal and external fields. The internal fields may even reverse the sign of the response (inverse or neg…
We have explored the electric field controlled magnetization in the nanodot CoFe2O4/SrRuO3/PMN-PT heterostructures. Ordered ferromagnetic CFO nanodots (~300 nm lateral dimension) are developed on the PMN-PT substrate (ferroelectric as well as piezoelectric) using a nanostencil-mask pattering method during pulsed laser deposition. The nanostructures reveal electric field induced magnetization reversal in the single domain CFO nanodots through transfer of piezostrains from the piezoelectric PMN-PT substrate to the CFO. Further, electric field modulated spin structure of CFO nanomagnets is analys…
Ferroelectrics are attractive candidate materials for environmentally friendly solid state refrigeration free of greenhouse gases. Their thermal response upon variations of external electric fields is largest in the vicinity of their phase transitions, which may occur near room temperature. The magnitude of the effect, however, is too small for useful cooling applications even when they are driven close to dielectric breakdown. Insight from microscopic theory is therefore needed to characterize materials and provide guiding principles to search for new ones with enhanced electrocaloric perform…
Lead based relaxor ferroelectric thin films have been of technological importance due to excellent properties for several commercial applications. However subtleness and high cost of fabrication have plagued of these materials. In this work a systematic study of PMN-PT thin films grown on LCMO buffered platinized glass substrates has been undertaken. The films were grown at room temperature using RF magnetron sputtering. Single phase PMN-PT films could be obtained by exsitu thermal annealing in air for 2h at temperatures 550 and 650 degree C. The films annealed at temperatures lower than 550 d…
Due to critical environmental and technological issues, there is a pressing need to switch from current refrigeration methods based on compression of gases to novel solid-state cooling technologies. Solid-state cooling is based on the thermal response of materials to external magnetic, electric, or mechanic fields, the so-called caloric effect. The electrocaloric (EC) effect, which is caused by electric fields and typically occurs in polar materials, is particularly promising from a technological point of view owing to its good scalability and natural implementation in circuitry. Simulation of…
The magneto-electrocaloric effect which can be defined as the coupling between magnetocaloric and electrocaloric effects attracts currently considerable attention due to the advantages provided by the caloric effect in designing solid-state refrigeration technologies. The magneto-electrocaloric effect of a multiferroic antiferromagnetic spin system with the Dzyaloshinskii Moriya (DM) interaction is investigated in this paper. The DM interaction is assimilated to a coupling between an external site-dependent electric field and a local electric polarization. The external magnetic is also conside…
We study the electrocaloric (EC) effect in bulk BaTiO$_3$ (BTO) using molecular dynamics simulations of a first principles-based effective Hamiltonian, combined with direct measurements of the adiabatic EC temperature change in BTO single crystals. We examine in particular the dependence of the EC effect on the direction of the applied electric field at all three ferroelectric transitions, and we show that the EC response is strongly anisotropic. Most strikingly, an inverse caloric effect, i.e., a temperature increase under field removal, can be observed at both ferroelectric-ferroelectric tra…
The electrocaloric (EC) effect and energy storage properties of eco-friendly ferroelectric Ba0.9Sr0.1Ti1-xSnxO3 (BSTS-x) ceramics prepared by the conventional solid-state reaction method were studied. Significant energy efficiency exceeding 80% was found in our samples. In particular, BSTS-5 and BSTS-10 samples exhibit 92% and 88% efficiency, respectively, over a wide temperature range around room temperature (RT). Direct EC measurement and an indirect method based on the thermodynamic approach were used to characterize the EC effect, and both yielded consistent results. The largest electrocal…
We present a field theory approach to study changes in local temperature due to an applied electric field (the electrocaloric effect) in electrolyte solutions. Steric effects and a field-dependent dielectric function are found to be of paramount importance for accurate estimations of the electrocaloric effect. Interestingly, electrolyte solutions are found to exhibit negative electrocaloric effects. Overall, our results point toward using fluids near room temperature with low heat capacity and high salt concentration for enhanced electrocalorics.
PbZr_{1-x}Ti_xO_3 (PZT) and Pb(Mg_{1/3}Nb_{2/3})_{1-x}Ti_xO_3 (PMN-$x$PT) are complex lead-oxide perovskites that display exceptional piezoelectric properties for pseudorhombohedral compositions near a tetragonal phase boundary. In PZT these compositions are ferroelectrics, but in PMN-xPT they are relaxors because the dielectric permittivity is frequency dependent and exhibits non-Arrhenius behavior. We show that the nanoscale structure unique to PMN-xPT and other lead-oxide perovskite relaxors is absent in PZT and correlates with a greater than 100% enhancement of the longitudinal piezoelectr…
Electric-field modulation of magnetism in strain-mediated multiferroic heterostructures is considered a promising scheme for enabling memory and magnetic microwave devices with ultralow power consumption. However, it is not well understood how electric-field-induced strain influences magnetic relaxation, an important physical process for device applications. Here we investigate resonant magnetization dynamics in ferromagnet/ferrolectric multiferroic heterostructures, FeGaB/PMN-PT and NiFe/PMN-PT, in two distinct strain states provided by electric-field-induced ferroelectric phase transition. T…
There is growing interest in heat pumps based on materials that show thermal changes when phase transitions are driven by changes of electric, magnetic or stress field. Importantly, regeneration permits sinks and loads to be thermally separated by many times the changes of temperature that can arise in the materials themselves. However, performance and parameterization are compromised by net heat transfer between caloric working bodies and heat transfer fluids. Here we show that this net transfer can be avoided-resulting in true, balanced regeneration-if one varies the applied electric field w…
Magnetoelectric composites are an important class of multiferroic materials that pave the way towards a new generation of multifunctional devices directly integrable in data storage technology and spintronics. This study focuses on strain-mediated electrical manipulation of magnetization in an extrinsic multiferroic. The composite includes 5 nm or 60 nm Fe$_{81}$Ga$_{19}$ thin films coupled to a piezoelectric (011)-PMN-PZT. The magnetization reversal study reveals a converse magnetoelectric coefficient $α_\mathrm{CME,max} \approx 2.7 \times {10^{-6}}$ s.m$^{-1}$ at room temperature. This repor…
The Ba0.85Ca0.15Zr0.1Ti0.9O3 (BCZT) ceramics were successfully prepared by sol-gel process, and sintered at 1420 degree. The effect of sintering times (2, 4 and 6 h) on structural, microstructural, electric properties, energy storage, and electrocaloric effect was systematically examined. X-ray diffraction (XRD) results show that all the samples crystallize in the pure perovskite structure. The morphotropic phase transition from the tetragonal to the orthorhombic phase (T-O) was identified and confirmed by Rietveld refinement. The BCZT ceramic sintered at 1420 degree for 4h possesses a good re…
Using Landau-Ginzburg-Devonshire theory and effective medium approximation, we analytically calculate typical dependences of the pyroelectric and electrocaloric coefficients on external electric field, temperature and radius for spherical single-domain ferroelectric nanoparticles. The considered physical model corresponds to the nanocomposite with small fraction of ferroelectric nanoparticles. Within the framework of the analytical model we establish how the size changes determine the temperature and field behavior pyroelectric and electrocaloric coefficients on example of BaTiO3 nanoparticles…
The paper describes heterostructures spontaneously formed in PMN-PT single crystals cooled under bias electric field applied along [001]pc and then zero-field-heated in the vicinity of the so-called depoling temperature. In particular, formation of lamellar structures composed of tetragonal-like and rhombohedral-like layers extending over macroscopic (mm) lengths is demonstrated by optical observations and polarized Raman investigations.
The electric-field-modulated resistance switching in VO2 thin films grown on piezoelectric (111)-0.68Pb(Mg1/3Nb2/3)O3-0.32PbTiO3 (PMN-PT) substrates has been investigated. Large relative change in resistance (10.7%) was observed in VO2/PMN-PT(111) hererostructures at room temperature. For a substrate with a given polarization direction, stable resistive states of VO2 films can be realized even when the applied electric fields are removed from the heterostructures. By sweeping electric fields across the heterostructure appropriately, multiple resistive states can be achieved. These stable resis…
