圆形层流射流中颗粒沉积模式的计算研究
A computational study of particle deposition patterns from a circular laminar jet
摘要:
利用OpenFOAM $^{\circledR}$ CFD软件包,采用拉格朗日方法,数值模拟了圆形层流射流作用下惯性冲击器平板上的颗粒沉积规律。喷嘴通道的锥角和射流到板的距离的影响进行了评估。结果表明,锥形喷嘴比直喷嘴更有利于颗粒向光斑边缘沉积。在射流雷诺数$Re = 1132$下,锥形喷嘴沉积颗粒以形成具有朝向沉积点边缘的高密度环的图案,特别是对于颗粒斯托克斯数$St > St_{50}$,这在直喷嘴中不存在。增大喷板间距有利于减小沉积点边缘附近的颗粒密度峰值。将$Re$还原为$283$(例如,对于通过$1.5$ mm直径喷嘴的$300$流动,当使用相同的锥形喷嘴时,产生在沉积点边缘没有高密度环的颗粒沉积图案。在$Re = 283$处具有直喷嘴的颗粒沉积图案在斑点边缘周围表现出进一步降低的颗粒密度,使得颗粒密度分布看起来或多或少像高斯函数。在一般情况下,减少$Re$对颗粒沉积模式的影响似乎是类似于增加射流到板的距离。计算出的颗粒沉积效率$η$表明,在射流轴附近具有极小$St$值的非常细的颗粒总是撞击板的中心,这表明随着$St$的大幅降低,$η$的值不会接近零。这种“小颗粒污染”通常相当于小颗粒的$\sim 10\%$(具有$\sqrt{St} < 0.1$)在$Re \sim 1000$和$\sim 5\%$在$Re \sim 300$,这在利用惯性冲击器测量的数据分析中不可忽略。
英文摘要:
Particle deposition patterns on the plate of inertial impactor with circular laminar jet are investigated numerically with a Lagrangian solver implemented within the framework of the OpenFOAM$^{\circledR}$ CFD package. Effects of taper angle of the nozzle channel and jet-to-plate distance are evaluated. The results show that tapered nozzle tends to deposit more particles toward the circular spot edge than straight nozzle. At jet Reynolds number $Re = 1132$, a tapered nozzle deposits particles to form a pattern with a high density ring toward the deposition spot edge, especially for particle Stokes number $St > St_{50}$, which is absent with a straight nozzle. Increasing the jet-to-plate distance tends to reduce the value of particle density peak near deposition spot edge. Reducing $Re$ to $283$ (e.g., for $300$ ccm flow through a $1.5$ mm diameter jet nozzle) yields particle deposition patterns without the high density ring at the deposition spot edge when the same tapered nozzle is used. The particle deposition patterns with the straight nozzle at $Re = 283$ exhibit further reduced particle density around the spot edge such that the particle density profile appears more or less like a Gaussian function. In general, the effect of reducing $Re$ on particle deposition pattern seems to be similar to increasing the jet-to-plate distance. The computed particle deposition efficiency $η$ shows the fact that very fine particles with extremely small values of $St$ near the jet axis always impact the center of plate, indicating that the value of $η$ does not approach zero with a substantial reduction of $St$. Such a "small particle contamination" typically amounts to $\sim 10\%$ of small particles (with $\sqrt{St} < 0.1$) at $Re \sim 1000$ and $\sim 5\%$ at $Re \sim 300$, which may not be negligible in data analysis with inertial impactor measurement.
机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。