In the context of a recoil damping analysis, we have designed and produced a membrane resonator equipped with a specific on-chip structure working as a "loss shield" for a circular membrane. In this device the vibrations of the membrane, with a quality factor of $10^7$, reach the limit set by the intrinsic dissipation in silicon nitride, for all the modes and regardless of the modal shape, also at low frequency. Guided by our theoretical model of the loss shield, we describe the design rationale of the device, which can be used as effective replacement of commercial membrane resonators in advanced optomechanical setups, also at cryogenic temperatures.
We observe transport of electrons through a metallic island on the tip of a nanomechanical pendulum. The resulting tunneling current shows distinct features corresponding to the discrete mechanical eigenfrequencies of the pendulum. We report on measurements covering the temperature range from 300 K down to 4.2 K. We explain the I-V curve, which differs from previous theoretical predictions, with model calculations based on a Master equation approach.
We present nanofabrication and mechanical measurements of single-crystal diamond cantilevers with thickness down to 85 nm, thickness uniformity better than 20 nm, and lateral dimensions up to 240 um. Quality factors exceeding one million are found at room temperature, surpassing those of state-of-the-art single-crystal silicon cantilevers of similar dimensions by roughly an order of magnitude. Force sensitivities of a few hundred zeptonewtons result for the best cantilevers at millikelvin temperatures. Single-crystal diamond could thus directly improve existing force and mass sensors by a simp…
We show that the vibrations of a nanomechanical resonator can be cooled to near its quantum ground state by tunnelling injection of electrons from an STM tip. The interplay between two mechanisms for coupling the electronic and mechanical degrees of freedom results in a bias-voltage dependent difference between the probability amplitudes for vibron emission and absorption during tunneling. For a bias voltage just below the Coulomb blockade threshold we find that absorption dominates, which leads to cooling corresponding to an average vibron population of the fundamental bending mode of 0.2.
We analyze the response of a nanomechanical resonator to an external drive when it is also coupled to a single-electron transistor (SET). The interaction between the SET electrons and the mechanical resonator depends on the amplitude of the mechanical motion leading to a strongly non-linear response to the drive which is similar to that of a Duffing oscillator. We show that the average dynamics of the resonator is well-described by a simple effective model which incorporates damping and frequency renormalization terms which are amplitude dependent. We also find that for a certain range of para…
The energy dissipation 1/Q (where Q is the quality factor) and resonance frequency characteristics of single-crystal 3C-SiC ultrahigh frequency (UHF) nanomechanical resonators are measured, for a family of UHF resonators with resonance frequencies of 295MHz, 395MHz, 411MHz, 420MHz, 428MHz, and 482MHz. A temperature dependence of dissipation, 1/Q ~ T^(0.3) has been identified in these 3C-SiC devices. Possible mechanisms that contribute to dissipation in typical doubly-clamped beam UHF resonators are analyzed. Device size and dimensional effects on the dissipation are also examined. Clamping los…
We analyze the noise properties of two single electron transistors (SETs) coupled via a shared voltage gate consisting of a nanomechanical resonator. Working in the regime where the resonator can be treated as a classical system, we find that the SETs act on the resonator like two independent heat baths. The coupling to the resonator generates positive correlations in the currents flowing through each of the SETs as well as between the two currents. In the regime where the dynamics of the resonator is dominated by the back-action of the SETs, these positive correlations can lead to parametrica…
We study the transverse oscillatory modes of nanomechanical silicon nitride strings under high tensile stress as a function of geometry and mode index m <= 9. Reproducing all observed resonance frequencies with classical elastic theory we extract the relevant elastic constants. Based on the oscillatory local strain we successfully predict the observed mode-dependent damping with a single frequency independent fit parameter. Our model clarifies the role of tensile stress on damping and hints at the underlying microscopic mechanisms.
A single-electron transistor incorporated as part of a nanomechanical resonator represents an extreme limit of electron-phonon coupling. While it allows for fast and sensitive electromechanical measurements, it also introduces backaction forces from electron tunnelling which randomly perturb the mechanical state. Despite the stochastic nature of this backaction, under conditions of strong coupling it is predicted to create self-sustaining coherent mechanical oscillations. Here, we verify this prediction using time-resolved measurements of a vibrating carbon nanotube transistor. This electromec…
We report on fabrication of large-scale arrays of suspended molybdenum disulfide (MoS2) atomic layers, as two-dimensional (2D) MoS2 nanomechanical resonators. We employ a water-assisted lift-off process to release chemical vapor deposited (CVD) MoS2 atomic layers from a donor substrate, followed by an all-dry transfer onto microtrench arrays. The resultant large arrays of suspended single- and few-layer MoS2 drumhead resonators (0.5 to 2um in diameter) offer fundamental resonances (f_0) in the very high frequency (VHF) band (up to ~120MHz) and excellent figures-of-merit up to f_0*Q ~ 3*10^10Hz…
Quantum mechanics demands that the act of measurement must affect the measured object. When a linear amplifier is used to continuously monitor the position of an object, the Heisenberg uncertainty relationship requires that the object be driven by force impulses, called back-action. Here we measure the back-action of a superconducting single-electron transistor (SSET) on a radiofrequency nanomechanical resonator. The conductance of the SSET, which is capacitively coupled to the resonator, provides a sensitive probe of the latter's position;back-action effects manifest themselves as an effectiv…
We demonstrate the direct photothermal probing and mapping of single plasmonic nanostructures via the temperature induced detuning of nanomechanical string resonators. Single Au nanoslits are illuminated with a low-power polarized focused laser beam (λ = 633 nm). Polarization dependent heat generation in gold nanoslits is then imaged with high sensitivity. A sensitivity of -4.1 ppm/nW with respect to the illuminated light (beam diameter 5.0pm0.8 μm) is determined for a single nanoslit (1 μm long and 53 nm wide), which equals to a total light absorption of 16%. This results in a heating of 0.5 …
Single-crystal diamond nanomechanical resonators are being developed for countless applications. A number of these applications require that the resonator be operated in a fluid, i.e., a gas or a liquid. Here, we investigate the fluid dynamics of single-crystal diamond nanomechanical resonators in the form of nanocantilevers. First, we measure the pressure-dependent dissipation of diamond nanocantilevers with different linear dimensions and frequencies in three gases, He, N$_2$, and Ar. We observe that a subtle interplay between the length scale and the frequency governs the scaling of the flu…
We theoretically investigate the deflection-induced coupling of an electron spin to vibrational motion due to spin-orbit coupling in suspended carbon nanotube quantum dots. Our estimates indicate that, with current capabilities, a quantum dot with an odd number of electrons can serve as a realization of the Jaynes-Cummings model of quantum electrodynamics in the strong-coupling regime. A quantized flexural mode of the suspended tube plays the role of the optical mode and we identify two distinct two-level subspaces, at small and large magnetic field, which can be used as qubits in this setup. …
We propose a scheme to measure the mass of a single particle using the nonlinear response of a 2D nanoresonator with degenerate eigenmodes. Using numerical and analytical calculations, we show that by driving a square graphene nanoresonator into the nonlinear regime, simultaneous determination of the mass and position of an added particle is possible. Moreover, this scheme only requires measurements in a narrow frequency band near the fundamental resonance.
Thermalization in nonlinear systems is a central concept in statistical mechanics and has been extensively studied theoretically since the seminal work of Fermi, Pasta and Ulam (FPU). Using molecular dynamics and continuum modeling of a ring-down setup, we show that thermalization due to nonlinear mode coupling intrinsically limits the quality factor of nanomechanical graphene drums and turns them into potential test beds for FPU physics. We find the thermalization rate $Γ$ to be independent of radius and scaling as $Γ\sim T^*/ε_{\rm pre}^2$, where $T^*$ and $ε_{\rm pre}$ are effective resonat…
Nanomechanical resonators have recently been highlighted because of their remarkable ability to perform the sensing and detection. Since the nanomechanical resonators are characterized by large surface-to-volume ratio, it is implied that the surface effect plays a substantial role on not only the resonance but also the sensing performance of nanomechanical resonators. In this work, we have studied the role of surface effect on the detection sensitivity of a nanoresonator that undergoes either harmonic vibration or nonlinear oscillation based on the continuum elastic model such as beam model. I…
We present results from a study of the nonlinear intermodal coupling between different flexural vibrational modes of a single high-stress, doubly-clamped silicon nitride nanomechanical beam. The measurements were carried out at 100 mK and the beam was actuated using the magnetomotive technique. We observed the nonlinear behavior of the modes individually and also measured the coupling between them by driving the beam at multiple frequencies. We demonstrate that the different modes of the resonator are coupled to each other by the displacement induced tension in the beam, which also leads to th…
We present a scheme of generating large-amplitude Schrödinger cat states and entanglement in a coupled system of nanomechanical resonator and single Cooper pair box (SCPB), without being limited by the magnitude of the coupling. It is shown that the entanglement between the resonator and the SCPB can be detected by a spectroscopic method.
We describe a cavity QED analogue for the coupling system of a spin and a nanomechanical resonator with a magnetic tip. For the quantized nanomechanical resonator, a spin-boson model for this coupling system can refer to a Jaynes-Cummings(JC) or an anti-JC model. These observations predict some quantum optical phenomena, such as squeezing and "collapse-revival" in the single oscillation mode of the nanomechanical resonator when it is initially prepared in the quasi-classical state. By modulating the phase of RF magnetic field one can switch the system between the JC and anti-JC model, which pr…
We describe a quantum computational architecture based on integrating nanomechanical resonators with Josephson junction phase qubits, with which we implement single- and multi-qubit operations. The nanomechanical resonator is a GHz-frequency, high-quality-factor dilatational resonator, coupled to the Josephson phase through a piezoelectric interaction. This system is analogous to one or more few-level atoms (the Josephson qubits) in a tunable electromagnetic cavity (the nanomechanical resonator). Our architecture combines the best features of solid-state and cavity-QED approaches, and may make…
We measure the energy relaxation rate of single- and few-layer molybdenum disulphide ($\mathrm{MoS_2}$) nanomechanical resonators by detecting the resonator ring-down. Recent experiments on these devices show a remarkably low quality (Q)-factor when taking spectrum measurements at room temperature. The origin of the low spectral Q-factor is an open question, and it has been proposed that besides dissipative processes, frequency fluctuations contribute significantly to the resonance line-width. The spectral measurements performed thus far however, do not allow one to distinguish these two proce…
Graphene-based electromechanical resonators have attracted much interest recently because of the outstanding mechanical and electrical properties of graphene and their various applications. However, the coupling between mechanical motion and charge transport has not been explored in graphene. Here, we studied the mechanical properties of a suspended 50-nm-wide graphene nanoribbon, which also acts as a single-electron transistor (SET) at low temperature. Using the SET as a sensitive detector, we found that the resonance frequency could be tuned from 82 MHz to 100 MHz and the quality factor exce…
Spin-mechanics studies interactions between spin systems and mechanical vibrations in a nanomechanical resonator and explores their potential applications in quantum information processing. In this tutorial, we summarize various types of spin-mechanical resonators and discuss both the cavity-QED-like and the trapped-ion-like spin-mechanical coupling processes. The implementation of these processes using negatively charged nitrogen vacancy and silicon vacancy centers in diamond is reviewed. Prospects for reaching the full quantum regime of spin-mechanics, in which quantum control can occur at t…
When performing continuous measurements of position with sensitivity approaching quantum mechanical limits, one must confront the fundamental effects of detector back-action. Back-action forces are responsible for the ultimate limit on continuous position detection, can also be harnessed to cool the observed structure, and are expected to generate quantum entanglement. Back-action can also be evaded, allowing measurements with sensitivities that exceed the standard quantum limit, and potentially allowing for the generation of quantum squeezed states. We realize a device based on the parametric…
We study locking phenomena of two strongly coupled, high-quality factor nanomechanical resonator modes subject to a common parametric drive at a single drive frequency. By controlled dielectric gradient forces we tune the resonance frequencies of the flexural in-plane and out-of-plane oscillation of the high stress silicon nitride string through their mutual avoided crossing. For the case of the strong common parametric drive signal-idler generation via parametric oscillation is observed, analogously to the framework of nonlinear optical effects in an optical parametric oscillator. Frequency t…
We present an analysis of the dynamics of a nanomechanical resonator coupled to a superconducting single electron transistor (SSET) in the vicinity of the Josephson quasiparticle (JQP) and double Josephson quasiparticle (DJQP) resonances. For weak coupling and wide separation of dynamical timescales, we find that for either superconducting resonance the dynamics of the resonator is given by a Fokker-Planck equation, i.e., the SSET behaves effectively as an equilibrium heat bath, characterised by an effective temperature, which also damps the resonator and renormalizes its frequency. Depending …
Silicon nitride (SiN) micro- and nanomechanical resonators have attracted a lot of attention in various research fields due to their exceptionally high quality factors ($Q$s). Despite their popularity, the origin of the limiting loss mechanisms in these structures has remained controversial. In this paper we propose an analytical model combining acoustic radiation loss with intrinsic loss. The model accurately predicts the resulting mode-dependent $Q$s of a low-stress silicon-rich and a high-stress stoichiometric SiN membrane. The large acoustic mismatch of the low-stress membrane to the subst…
The detection of mechanical vibrations near the quantum limit is a formidable challenge since the displacement becomes vanishingly small when the number of phonon quanta tends towards zero. An interesting setup for on-chip nanomechanical resonators is that of coupling them to electrical microwave cavities for detection and manipulation. Here we show how to achieve a large cavity coupling energy of up to (2 π) 1 MHz/nm for metallic beam resonators at tens of MHz. We used focused ion beam (FIB) cutting to produce uniform slits down to 10 nm, separating patterned resonators from their gate electr…
We report on a nanomechanical engineering method to monitor matter growth in real time via e-beam electromechanical coupling. This method relies on the exceptional mass sensing capabilities of nanomechanical resonators. Focused electron beam induced deposition (FEBID) is employed to selectively grow platinum particles at the free end of singly clamped nanotube cantilevers. The electron beam has two functions: it allows both to grow material on the nanotube and to track in real time the deposited mass by probing the noise-driven mechanical resonance of the nanotube. On the one hand, this detect…
We analyse the quantum dynamics of a nanomechanical resonator coupled to a normal-state single-electron transistor (SET). Starting from a microscopic description of the system, we derive a master equation for the SET island charge and resonator which is valid in the limit of weak electro-mechanical coupling. Using this master equation we show that, apart from brief transients, the resonator always behaves like a damped harmonic oscillator with a shifted frequency and relaxes into a thermal-like steady state. Although the behaviour remains qualitatively the same, we find that the magnitude of t…
We introduce an approach to quantum information processing where the information is stored in the motional degrees of freedom of nanomechanical devices. The qubits of our approach are formed by the two lowest energy levels of mechanical resonators which are tuned to be strongly anharmonic by suitable electrostatic fields. Single qubit rotations are conducted by radio frequency voltage pulses that are applied to individual resonators. Two qubit entangling gates in turn are implemented via a coupling of two qubits to a common optical resonance of a high finesse cavity. We find that gate fideliti…
Micro- and nanomechanical systems with exceptionally low dissipation rates are enabling the next-generation technologies of ultra-sensitive detectors and quantum information systems. New techniques and methods for lowering the dissipation rate have in recent years been discovered and allowed for the engineering of mechanical oscillators with phononic modes that are extremely well isolated from the environment and thus possessing quality factors close to and beyond 1 billion. A powerful strategy for isolating and controlling a single phononic mode is based on phononic crystal engineering. Here …
Superfluids, such as superfluid $^3\mathrm{He}$ and $^4\mathrm{He}$, exhibit a broad range of quantum phenomena and excitations which are unique to these systems. Nanoscale mechanical resonators are sensitive and versatile force detectors with the ability to operate over many orders of magnitude in damping. Using nanomechanical-doubly clamped beams of extremely high quality factors ($Q>10^6$), we probe superfluid $^4\mathrm{He}$ from the superfluid transition temperature down to $\mathrm{mK}$ temperatures at frequencies up to $11.6 \, \mathrm{MHz}$. Our studies show that nanobeam damping is do…
We investigate the influence of gold thin-films subsequently deposited on a set of initially bare, doubly clamped, high-stress silicon nitride string resonators at room temperature. Analytical expressions for resonance frequency, quality factor and damping for both in- and out-of-plane flexural modes of the bilayer system are derived, which allows for the determination of effective elastic parameters of the composite structure from our experimental data. We find the inverse quality factor to scale linearly with the gold film thickness, indicating that the overall damping is governed by losses …
Nanomechanical resonators are used as high performance detectors in a variety of applications such as mass spectrometry and atomic force microscopy. Initial emphasis in nanomechanical resonant sensor research was on increasing the sensitivity to the level of a single molecule, atom and beyond. On the other hand, there are applications where the speed of detection is crucial, prompting recent works that emphasize sensing schemes with improved time resolution. We first develop a general modeling framework encompassing all resonator tracking schemes currently in use, by extending recent previous …
The shape of a nanomechanical resonator profoundly affects its mechanical properties and determines its suitability for various applications, such as ultra-sensitive mass and force detection. Despite the promise of two-dimensional nanomechanical systems in such applications, full control over the shape of suspended two-dimensional materials, such as graphene, has not been achieved. We present an effective, single-step method to shape presuspended graphene into nanomechanical resonators with arbitrary geometries leading to enhanced properties in comparison to conventional drumheads. Our techniq…
Heterostructures play significant roles in modern semiconductor devices and micro/nanosystems in a plethora of applications in electronics, optoelectronics, and transducers. While state-of-the-art heterostructures often involve stacks of crystalline epi-layers each down to a few nanometers thick, the intriguing limit would be heterto-atomic-layer structures. Here we report the first experimental demonstration of freestanding van der Waals heterostructures and their functional nanomechanical devices. By stacking single-layer (1L) MoS2 on top of suspended single-, bi-, tri- and four-layer (1L to…
We propose and analyze a hybrid device by integrating a microscale diamond beam with a single built-in nitrogen-vacancy (NV) center spin to a superconducting coplanar waveguide (CPW) cavity. We find that under an ac electric field the quantized motion of the diamond beam can strongly couple to the single cavity photons via dielectric interaction. Together with the strong spin-motion interaction via a large magnetic field gradient, it provides a hybrid quantum device where the dia- mond resonator can strongly couple both to the single microwave cavity photons and to the single NV center spin. T…
Recent advances in nanotechnology have led to the development of nano-electro-mechanical systems (NEMS) such as nanomechanical resonators, which have recently received significant attention from the scientific community. This has not only been for their capability for the label-free detection of bio/chemical-molecules at single-molecule (or atomic) resolution for future applications such as the early diagnostics of diseases such as cancer, but also for their unprecedented ability to detect physical quantities such as molecular weight, elastic stiffness, surface stress, and surface elastic stif…
We study a general model describing a self-detecting single electron transistor realized by a suspended carbon nanotube actuated by a nearby antenna. The main features of the device, recently observed in a number of experiments, are accurately reproduced. When the device is in a low current-carrying state, a peak in the current signals a mechanical resonance. On the contrary, a dip in the current is found in high current-carrying states. In the nonlinear vibration regime of the resonator, we are able to reproduce quantitatively the characteristic asymmetric shape of the current-frequency curve…
We propose a spin-mechanical device to control and detect spin currents by mechanical torque. Our hybrid nano-electro-mechanical device, which contains a nanowire with a ferromagnetic-nonmagnetic interface, is designed to measure or induce spin polarized currents. Since spin carries angular momentum, a spin flip or spin transfer process involves a change in angular momentum--and hence, a torque--which enables mechanical measurement of spin flips. Conversely, an applied torque can result in spin polarization and spin current.
We show that the nanoresonator position can be squeezed significantly below the ground state level by measuring the nanoresonator with a quantum point contact or a single-electron transistor and applying a periodic voltage across the detector. The mechanism of squeezing is basically a generalization of quantum nondemolition measurement of an oscillator to the case of continuous measurement by a weakly coupled detector. The quantum feedback is necessary to prevent the ``heating'' due to measurement back-action. We also discuss a procedure of experimental verification of the squeezed state.
Magnetically coupled hybrid quantum systems enable robust quantum state control through Landau-Zener transitions. Here, we show that an ultracold atomic sample coupled to a nanomechanical resonator via oscillating magnetic fields can be used to cool the resonator's mechanical motion, to measure the mechanical temperature, and to enable entanglement of these mesoscopic objects. We calculate the expected coupling for both permanent-magnet and current-conducting nanostring resonators and describe how this hybridization is attainable using recently developed fabrication techniques, including SiN n…
We realise a circular gray-field polariscope to image stress-induced birefringence in thin (submicron thick) silicon nitride (SiN) membranes and strings. This enables quantitative mapping of the orientation of principal stresses and stress anisotropy, complementary to, and in agreement with, finite element modeling (FEM). Furthermore, using a sample with a well known stress anisotropy, we extract a new value for the photoelastic (Brewster) coefficient of silicon nitride, $C \approx (3.4~\pm~0.1)\times~10^{-6}~\mathrm{MPa}^{-1}$. We explore possible applications of the method to analyse and qua…
We have used the mechanical motion of a carbon nanotube (CNT) as a probe of the average charge on a quantum dot. Variations of the resonance frequency and the quality factor are determined by the change in average charge on the quantum dot during a mechanical oscillation. The average charge, in turn, is influenced by the gate voltage, the bias voltage, and the tunnel rates of the barriers to the leads. At bias voltages that exceed the broadening due to tunnel coupling, the resonance frequency and quality factor show a double dip as a function of gate voltage. We find that increasing the curren…
Mechanical properties of a nanomechanical resonator have a significant impact on the performance of a resonant Nano-electromechanical system (NEMS) device. Here we study the mechanical properties of suspended membranes fabricated out of low-pressure chemical vapor deposited silicon nitride thin films. Doubly-clamped membranes of silicon nitride with thickness less than 50 nm and length varying from 5 um to 60 um were fabricated. The elastic modulus and stress in the suspended membranes were measured using Atomic Force Microscope (AFM)-based nanomechanical spectroscopy. The elastic modulus of t…
The motion of a mechanical resonator is intrinsically decomposed over a collection of normal modes of vibration. When the resonator is used as a sensor, its multimode nature often deteriorates or limits its performance and sensitivity. This challenge is frequently encountered in state-of-the-art optomechanical sensing platforms. We present a mechanical design strategy that ensures that optomechanical measurements can retrieve information on a single mechanical degree of freedom, and implement it in a sliced photonic crystal nanobeam resonator. A spectral design approach is used to make mechani…
We report on the non-destructive measurement of Young's modulus of thin-film single crystal beta gallium oxide (beta-Ga2O3) out of its nanoscale mechanical structures by measuring their fundamental mode resonance frequencies. From the measurements, we extract Young's modulus in (100) plane, EY,(100) = 261.4+/-20.6 GPa, for beta-Ga2O3 nanoflakes synthesized by low-pressure chemical vapor deposition (LPCVD), and Young's modulus in [010] direction, EY,[010] = 245.8+/-9.2 GPa, for beta-Ga2O3 nanobelts mechanically cleaved from bulk beta-Ga2O3 crystal grown by edge-defined film-fed growth (EFG) met…
Damping-dependent thermalization of neighboring nanomechanical resonators below 1 mK
Swiss Federal Institute of Technology Lausanne (EPFL)（洛桑联邦理工学院）；EDWATEC SA（EDWATEC公司）；Univ. Grenoble Alpes, CNRS, Grenoble INP, Institut Néel（格勒诺布尔阿尔卑斯大学、法国国家科学研究中心、格勒诺布尔理工学院、内耳研究所）
The rapid experimental progress in the field of superconducting nanocircuits gives rise to an increasing quest for advanced quantum-control techniques for these macroscopically coherent systems. Here we demonstrate theoretically that stimulated Raman adiabatic passage (STIRAP) should be possible with the quantronium setup of a Cooper-pair box. The scheme appears to be robust against decoherence and should be realizable even with the existing technology. As an application we present a method to generate single-phonon states of a nanomechnical resonator by vacuum-stimulated adiabatic passage wit…
We study a resonator coupled to a generic detector and calculate the noise spectra of the two sub-systems. We describe the coupled system by a closed, linear, set of Langevin equations and derive a general form for the finite frequency noise of both the resonator and the detector. The resonator spectrum is the well-known thermal form with an effective damping, frequency shift and diffusion term. In contrast, the detector noise shows a rather striking Fano-like resonance, i.e. there is a resonance at the renormalized frequency, and an anti-resonance at the bare resonator frequency. As examples …
We report actuation and detection of gigahertz-range resonance frequencies in nano-crystalline diamond mechanical resonators. High order transverse vibration modes are measured in coupled-beam resonators exhibiting frequencies up to 1.441 GHz. The cantilever-array design of the resonators translates the gigahertz-range resonant motion of micron-long cantilever elements to the displacement of the central supporting structure. Use of nano-crystalline diamond further increases the frequency compared to single crystal silicon by a factor of three. High clamping losses usually associated with micro…
We analyze squeezing of the nanoresonator state produced by periodic measurement of position by a quantum point contact or a single-electron transistor. The mechanism of squeezing is the stroboscopic quantum nondemolition measurement generalized to the case of continuous measurement by a weakly coupled detector. The magnitude of squeezing is calculated for the harmonic and stroboscopic modulations of measurement, taking into account detector efficiency and nanoresonator quality factor. We also analyze the operation of the quantum feedback, which prevents fluctuations of the wavepacket center d…
