Recently, several advanced multi-antenna radio communications technologies have emerged to meet the increased capacity demands in wireless multi-user networks. Despite their great potential, the extent of these techniques' practical applicability still remains questionable, since they have to face either backhaul limitations or cost and hardware constraints. In this paper, we propose a new system solution which includes network architecture, antenna technology and radio transmission protocol to reduce drastically the hardware complexity and cost as well as the channel state information / user data feedback requirements of multi-user multi-antenna wireless networks. We focus on the forward link of an interference channel in a cloud radio access network setup wherein an arbitrary number of remote radio heads are each equipped with a single radio frequency module parasitic antenna array and wish to send data to their respective single-antenna user terminals, while co-existing in time and frequency. Base stations select cooperatively the optimal combination of pre-determined beams prior transmission. Our proposed approach is able to achieve the aforementioned goals, while offering significant downlink sum-rate gains due to the available spatial degrees of freedom.
This work considers multiple-input multiple-output (MIMO) communication systems using hierarchical modulation. A disadvantage of the maximum-likelihood (ML) MIMO detector is that computational complexity increases exponentially with the number of transmit antennas. To reduce complexity, we propose a hierarchical modulation scheme to be used in MIMO trans- mission where base and enhancement layers are incorporated. In the proposed receiver, the base layer is detected first with a minimum mean square error (MMSE) detector which is followed by ML detection of the enhancement layer. Our results in…
Massive multiple-inputmultiple-output (MIMO) systems, dense small-cells (SCs), and full duplex are three candidate techniques for next-generation communication systems. The cooperation of next-generation techniques could offer more benefits, e.g., SC in-band wireless backhaul in massive MIMO systems. In this paper, three strategies of SC in-band wireless backhaul in massive MIMO systems are introduced and compared, i.e., complete time-division duplex (CTDD), zero-division duplex (ZDD), and ZDD with interference rejection (ZDD-IR). Simulation results demonstrate that SC in-band wireless backhau…
Multiple-input multiple-output orthogonal frequency division multiplexing with index modulation (MIMO-OFDM-IM) is a novel multicarrier transmission technique which has been proposed recently as an alternative to classical MIMO-OFDM. In this scheme, OFDM with index modulation (OFDM-IM) concept is combined with MIMO transmission to take advantage of the benefits of these two techniques. In this paper, we shed light on the implementation and error performance analysis of the MIMO-OFDM-IM scheme for next generation 5G wireless networks. Maximum likelihood (ML), near-ML, simple minimum mean square …
Full-dimensional (FD) channel state information at transmitter (CSIT) has always been a major limitation of the spectral efficiency of cellular multi-input multi-output (MIMO) networks. This letter proposes an FD-directional spatial channel estimation algorithm for frequency division duplex massive FD-MIMO systems. The proposed algorithm uses the statistical spatial correlation between the uplink (UL) and downlink (DL) channels of each user equipment. It spatially decomposes the UL channel into azimuthal and elevation dimensions to estimate the array principal receive responses. An FD spatial …
Millimeter-wave (mmWave) communication is considered as an indispensable technique for the next-generation backhaul/fronthaul network thanks to its large transmission bandwidth. Especially for heterogeneous network (HetNet), the mmWave full-dimension (FD)-MIMO is exploited to establish the backhaul/fronthaul link between phantom-cell base stations (BSs) and macro-cell BSs, where an efficient precoding is prerequisite. Against this background, this paper proposes a principle component analysis (PCA)-based hybrid precoding for wideband mmWave MIMO backhaul/fronthaul channels. We first propose an…
Multi-user Multiple-Input Multiple-Output (MIMO) offers big advantages over conventional point-to-point MIMO: it works with cheap single-antenna terminals, a rich scattering environment is not required, and resource allocation is simplified because every active terminal utilizes all of the time-frequency bins. However, multi-user MIMO, as originally envisioned with roughly equal numbers of service-antennas and terminals and frequency division duplex operation, is not a scalable technology. Massive MIMO (also known as "Large-Scale Antenna Systems", "Very Large MIMO", "Hyper MIMO", "Full-Dimensi…
Large-scale multi-user multiple-input multiple-output (MIMO) techniques have the potential to bring tremendous improvements for future communication systems. Counter-intuitively, the practical issues of having uncertain channel knowledge, high propagation losses, and implementing optimal non-linear precoding are solved more-or-less automatically by enlarging system dimensions. However, the computational precoding complexity grows with the system dimensions. For example, the close-to-optimal regularized zero-forcing (RZF) precoding is very complicated to implement in practice, since it requires…
Large Language Model Empowered Next-Generation MIMO Networks: Fundamentals, Challenges, and Visions
State Key Laboratory of Advanced Rail Autonomous Operation（先进轨道交通自主运行状态关键实验室）；Beijing Jiaotong University（北京交通大学）；School of Electronics and Information Engineering（电子与信息工程学院）；University of Hong Kong（香港大学）；College of Computing & Data Science（计算与数据科学学院）；Nanyang Technological University（南洋理工大学）；Hong Kong University of Science and Technology（香港科技大学）
Massive MIMO (multiple-input multiple-output) is no longer a "wild" or "promising" concept for future cellular networks - in 2018 it became a reality. Base stations (BSs) with 64 fully digital transceiver chains were commercially deployed in several countries, the key ingredients of Massive MIMO have made it into the 5G standard, the signal processing methods required to achieve unprecedented spectral efficiency have been developed, and the limitation due to pilot contamination has been resolved. Even the development of fully digital Massive MIMO arrays for mmWave frequencies - once viewed pro…
Massive Multiple-Input Multiple-Output (MIMO) is foreseen to be one of the main technology components in next generation cellular communications (5G). In this paper, fundamental limits on the performance of downlink massive MIMO systems are investigated by means of simulations and analytical analysis. Signal-to-noise-and-interference ratio (SINR) and sum rate for a single-cell scenario multi-user MIMO are analyzed for different array sizes, channel models, and precoding schemes. The impact of hardware impairments on performance is also investigated. Simple approximations are derived that show …
How would a cellular network designed for high energy efficiency look like? To answer this fundamental question, we model cellular networks using stochastic geometry and optimize the energy efficiency with respect to the density of base stations, the number of antennas and users per cell, the transmit power levels, and the pilot reuse. The highest efficiency is neither achieved by a pure small-cell approach, nor by a pure massive MIMO solution. Interestingly, it is the combination of these approaches that provides the highest energy efficiency; small cells contributes by reducing the propagati…
This paper proposes a joint transmitter-receiver design to minimize the weighted sum power under the post-processing signal-to-interference-and-noise ratio (post-SINR) constraints for all subchannels. Simulation results demonstrate that the algorithm can not only satisfy the post-SINR constraints but also easily adjust the power distribution among the users by changing the weights accordingly. Hence the algorithm can be used to alleviates the adjacent cell interference by reducing the transmitting power to the edge users without performance penalty.
Massive multiple-input multiple-output (MIMO) systems are a main enabler of the excessive throughput requirements in 5G and future generation wireless networks as they can serve many users simultaneously with high spectral and energy efficiency. To achieve this, massive MIMO systems require accurate and timely channel state information (CSI), which is acquired by a training process that involves pilot transmission, CSI estimation and feedback. This training process incurs a training overhead, which scales with the number of antennas, users and subcarriers. Reducing this training overhead in ma…
Massive multiple-input multiple-output (MIMO) communications are the focus of considerable interest in recent years. While the theoretical gains of massive MIMO have been established, implementing MIMO systems with large-scale antenna arrays in practice is challenging. Among the practical challenges associated with massive MIMO systems are increased cost, power consumption, and physical size. In this work we study the implementation of massive MIMO antenna arrays using dynamic metasurface antennas (DMAs), an emerging technology which inherently handles the aforementioned challenges. Specifical…
Multiple-input multiple-output (MIMO) systems with a large number of basestation antennas, often called massive MIMO, have received much attention in academia and industry as a means to improve the spectral efficiency, energy efficiency, and processing complexity of next generation cellular system. Mobile communication industry has initiated a feasibility study of massive MIMO systems to meet the increasing demand of future wireless systems. Field trials of the proof-of-concept systems have demonstrated the potential gain of the Full-Dimension MIMO (FD-MIMO), an official name for the MIMO enha…
This paper investigates Cell-Free massive MIMO networks, where each access point (AP) is equipped with a hybrid transceiver, reducing the complexity and cost compared to a fully digital transceiver. Asymptotic approximations for the spectral efficiency are derived for uplink and downlink. Capitalizing on these expressions, a max-min problem is formulated to optimize the (i) analog beamformer at the APs and (ii) pilot assignment. Simulations show that the optimization of these variables substantially increases the network performance.
In this paper, we propose a novel genie chains approach to obtain information theoretic degrees of freedom (DoF) outer bounds for MIMO wireless interference networks. This new approach creates a chain of mappings from genie signals provided to a receiver to the exposed signal spaces at that receiver, which then serve as the genie signals for the next receiver in the chain subject to certain linear independence requirements, essentially converting an information theoretic DoF outer bound problem into a linear algebra problem. Several applications of the genie chains approach are presented.
Fifth generation (5G) wireless systems are expected to combine emerging transmission technologies, such as large-scale multiple-input multiple-output (MIMO) and non-orthogonal multi-carrier waveforms, to improve the spectral efficiency and to reduce out-of-band (OOB) emissions. This paper investigates the efficacy of two promising multi-carrier waveforms that reduce OOB emissions in combination with large-scale MIMO, namely filter bank multi-carrier (FBMC) and generalized frequency division multiplexing (GFDM). We develop novel, low-complexity data detection algorithms for both of these wavefo…
Massive Multiple-input Multiple-output (MIMO) adaption is one of the primary evolving objectives for the next generation high speed train (HST) communication system. In this paper, we consider how to design an efficient low-complexity location-aware beamforming for the multi-user (MU) massive MIMO system in HST scenario. We first put forward a low-complexity beamforming based on location information, where multiple users are considered. Then, without considering inter-beam interference, a closed-form solution to maximize the total service competence of base station (BS) is proposed in this MU …
Due to the relatively high cost of deploying optical fibers, free space optical (FSO) links have been developed as a cost-effective alternative technology for next generation cellular networks. However, in order to have a practical role in the physical layer of future communication systems, data rate of FSO links must be improved. To this aim, in this paper we employ a multiple-input multiple-output (MIMO) multiplexing scheme with two transceivers to increase the data rate of the considered FSO system. Unlike MIMO diversity case, the performance of MIMO multiplexing is significantly affected b…
Recent Advances in Near-Field Beam Training and Channel Estimation for XL-MIMO Systems
Laval University（拉瓦尔大学）；Central China Normal University（华中师范大学）；Zhengzhou University（郑州大学）；University of Nottingham, Ningbo, China（诺丁汉大学（中国宁波））；Hunan Institute of Science and Technology（湖南科技学院）；The University of Dublin（都柏林大学）
This paper focuses on the design of beamforming codebooks that maximize the average normalized beamforming gain for any underlying channel distribution. While the existing techniques use statistical channel models, we utilize a model-free data-driven approach with foundations in machine learning to generate beamforming codebooks that adapt to the surrounding propagation conditions. The key technical contribution lies in reducing the codebook design problem to an unsupervised clustering problem on a Grassmann manifold where the cluster centroids form the finite-sized beamforming codebook for th…
In this paper, we propose a full-rate full-diversity space-time block code (STBC) for 2x2 reconfigurable multiple-input multiple-output (MIMO) systems that require a low complexity maximum likelihood (ML) detector. We consider a transmitter equipped with a linear antenna array where each antenna element can be independently configured to create a directive radiation pattern toward a selected direction. This property of transmit antennas allow us to increase the data rate of the system, while reducing the computational complexity of the receiver. The proposed STBC achieves a coding rate of two …
In this paper, the problem of designing a linear precoder for Multiple-Input Multiple-Output (MIMO) systems in conjunction with Quadrature Amplitude Modulation (QAM) is addressed. First, a novel and efficient methodology to evaluate the input-output mutual information for a general Multiple-Input Multiple-Output (MIMO) system as well as its corresponding gradients is presented, based on the Gauss-Hermite quadrature rule. Then, the method is exploited in a block coordinate gradient ascent optimization process to determine the globally optimal linear precoder with respect to the MIMO input-outpu…
Large-scale MIMO systems have been considered as one of the possible candidates for the next-generation wireless communication technique, due to their potential to provide significant higher throughput than conventional wireless systems. For such systems, Zero-Forcing (ZF) and Conjugate Beamforming (CB) precoding have been considered as two possible practical spatial multiplexing techniques, and their average achievable sum rates have been derived on the sum power constraint. However, in practice, the transmitting power at a base station is constrained under each antenna. In this case, the opt…
The problem of the real-time multiple-input multiple-output (MIMO) array control when requirements on capacity performance, out-of-cell interference, and computational efficiency are simultaneously enforced is addressed by means of an innovative hybrid beamforming technique. The synthesis of the excitations of the MIMO system is first re-formulated as that of matching an ideal "hybrid" pattern fitting capacity or low-interference constraints along the angular coordinates. Then, a non-iterative processing scheme is derived for each MIMO beam where numerically-efficient synthesis techniques are …
Deploying antenna arrays with an asymptotically large aperture will be central to achieving the theoretical gains of massive MIMO in beyond-5G systems. Such extra-large MIMO (XL-MIMO) systems experience propagation conditions which are not typically observed in conventional massive MIMO systems, such as spatial non-stationarities and near-field propagation. Moreover, standard precoding schemes, such as zero-forcing (ZF), may not apply to XL-MIMO transmissions due to the prohibitive complexity associated with such a large-scale scenario. We propose two novel precoding schemes that aim at reduci…
In this paper, we propose a new multiple-input multiple-output (MIMO) communication system with movable antennas (MAs) to exploit the antenna position optimization for enhancing the capacity. Different from conventional MIMO systems with fixed-position antennas (FPAs), the proposed system can flexibly change the positions of transmit/receive MAs, such that the MIMO channel between them is reconfigured to achieve higher capacity. We aim to characterize the capacity of MA-enabled point-to-point MIMO communication systems, by jointly optimizing the positions of transmit and receive MAs as well as…
Millimeter wave offers high bandwidth for air-to-air (A2A) communication. In this paper, we evaluate the rate performance of a multiuser MIMO (MU-MIMO) configuration where several aircraft communicate with a central hub. We consider a hybrid subarray architecture, single path channels, and realistic atmospheric attenuation effects. We propose a mathematical framework for the analysis of millimeter wave (mmWave) MU-MIMO networks. Via Monte Carlo simulation, we demonstrate that mmWave is a promising technology for delivering gigabit connectivity in next-generation aerial networks.
Communications at mmWave frequencies will be a key enabler of the next generation of cellular networks, due to the multi-Gbps rate that can be achieved. However, there are still several problems that must be solved before this technology can be widely adopted, primarily associated with the interplay between the variability of mmWave links and the complexity of mobile networks. An end-to-end network simulator represents a great tool to assess the performance of any proposed solution to meet the stringent 5G requirements. Given the criticality of channel propagation characteristics at higher fre…
A novel distributed space-time block code (STBC) for the next generation mobile TV broadcasting is proposed. The new code provides efficient performance within a wide range of power imbalance showing strong adaptivity to the single frequency network (SFN) broadcasting deployments. The new code outperforms existing STBCs with equivalent decoding complexity and approaches those with much higher complexities.
We consider a cell-free Massive multiple-input multiple-output (MIMO) system and investigate the system performance for the case when the quantized version of the estimated channel and the quantized received signal are available at the central processing unit (CPU), and the case when only the quantized version of the combined signal with maximum ratio combining (MRC) detector is available at the CPU. Next, we study the max-min optimization problem, where the minimum user uplink rate is maximized with backhaul capacity constraints. To deal with the max-min non-convex problem, we propose to deco…
In mobile cellular networks, it is estimated that more than 60% of voice and data services occur indoors. Therefore, cellular network operators have shown an unprecedented interest in research on femtocell systems from various aspects to extend the indoor wireless coverage for providing high-quality and high data-rate wireless multimedia services contents. In an effort for reducing the bit-error probabilities (BEPs) and also increasing bit/symbol capacity of bandwidth limited error-prone wireless channels in femtocell propagation areas, this paper presents the performance of a promising candid…
In cellular communication systems, it is conventional to assume the absence of a line of sight (LoS) path between the users and their associated access points (APs). This assumption however becomes questionable in the context of recent developments in the direction of cell free (CF) massive MIMO systems. In the CF massive MIMO, the AP density is assumed to be comparable with the user density, which increases probability of existence of an LoS path between the users and their associated APs. In this paper, we analyze the performance of an uplink CF massive MIMO system, with a probabilistic LoS …
Massive multiple-input multiple-output (MIMO) is recognized as a promising technology for the next generation of wireless networks because of its potential to increase the spectral efficiency. In initial studies of massive MIMO, the system has been considered to be perfectly synchronized throughout the entire cells. However, perfect synchronization may be hard to attain in practice. Therefore, we study a massive MIMO system whose cells are not synchronous to each other, while transmissions in a cell are still synchronous. We analyze an asynchronous downlink massive MIMO system in terms of the …
In this paper, an optimization framework is proposed for joint transceiver beamforming and admission control in massive MIMO cognitive radio networks. The objective of the optimization problem is to support maximum number of secondary users in downlink transmission with constraints on the total power allocated to users, the rate achieved at secondary users and the interference at the primary nodes. The proposed framework takes into account the imperfect knowledge of the channels between the secondary and the primary nodes and also mitigates the interference caused by the primary users at secon…
V-BLAST detection method suffers large computational complexity due to its successive detection of symbols. In this paper, we propose a modified V-BLAST algorithm to decrease the computational complexity by reducing the number of detection iterations required in MIMO communication systems. We begin by showing the existence of a maximum number of iterations, beyond which, no significant improvement is obtained. We establish a criterion for the number of maximum effective iterations. We propose a modified algorithm that uses the measured SNR to dynamically set the number of iterations to achieve…
Enhanced mobile broadband (eMBB) is one of the key use-cases for the development of the new standard 5G New Radio for the next generation of mobile wireless networks. Large-scale antenna arrays, a.k.a. Massive MIMO, the usage of carrier frequencies in the range 10-100 GHz, the so-called millimeter wave (mm-wave) band, and the network densification with the introduction of small-sized cells are the three technologies that will permit implementing eMBB services and realizing the Gbit/s mobile wireless experience. This paper is focused on the massive MIMO technology; initially conceived for conve…
Block diagonalization (BD) is an attractive technique that transforms the multi-user multiple-input multiple-output (MU-MIMO) channel into parallel single-user MIMO (SU-MIMO) channels with zero inter-user interference (IUI). In this paper, we combine the BD technique with two deterministic vector perturbation (VP) algorithms that reduce the transmit power in MU-MIMO systems with linear precoding. These techniques are the fixed-complexity sphere encoder (FSE) and the QR-decomposition with M-algorithm encoder (QRDM-E). In contrast to the conventional BD VP technique, which is based on the sphere…
One key feature of massive multiple-input multiple-output systems is the large number of antennas and users. As a result, reducing the computational complexity of beamforming design becomes imperative. To this end, the goal of this paper is to achieve a lower complexity order than that of existing beamforming methods, via the parallel accelerated random coordinate descent (ARCD). However, it is known that ARCD is only applicable when the problem is convex, smooth, and separable. In contrast, the beamforming design problem is nonconvex, nonsmooth, and nonseparable. Despite these challenges, thi…
This paper compares the sum rates and rate regions achieved by power-domain NOMA (non-orthogonal multiple access) and standard massive MIMO (multiple-input multiple-output) techniques. We prove analytically that massive MIMO always outperforms NOMA in i.i.d.~Rayleigh fading channels, if a sufficient number of antennas are used at the base stations. The simulation results show that the crossing point occurs already when having 20-30 antennas, which is far less than what is considered for the next generation cellular networks.
In this paper, distributed user scheduling schemes are proposed for the multi-user MIMO-Y channel, where three $N_{T}$-antenna users ($N_{T}=2N,\,3N$) are selected from three clusters to exchange information via an $N_{R}$-antenna amplify-and-forward (AF) relay ($N_{R}=3N$), and $N\geq1$ represents the number of data stream(s) of each unicast transmission within the MIMO-Y channel. The proposed schemes effectively harvest multi-user diversity (MuD) without the need of global channel state information (CSI) or centralized computations. In particular, a novel reference signal space (RSS) is prop…
To meet the goal of ten-fold increase in spectral efficiency, multiuser multiple-input-multiple-output (MU-MIMO) techniques capable of achieving high spatial multiplexing gains are expected to be an essential component of fifth-generation (5G) radio access systems. This increase in multiplexing gain, made possible by equipping base stations with a large number of antennas, entails a proportional increase in channel state information (CSI) acquisition overhead. This article addresses the problem of reducing this CSI overhead by optimizing the amount of time-frequency resources allocated for cha…
There is considerable interest in the combined use of millimeter-wave (mmwave) frequencies and arrays of massive numbers of antennas (massive MIMO) for next-generation wireless communications systems. A symbiotic relationship exists between these two factors: mmwave frequencies allow for densely packed antenna arrays, and hence massive MIMO can be achieved with a small form factor; low per-antenna SNR and shadowing can be overcome with a large array gain; steering narrow beams or nulls with a large array is a good match for the line-of-sight (LOS) or near-LOS mmwave propagation environments, e…
MIMO mobile systems, with a large number of antennas at the base-station side, enable the concurrent transmission of multiple, spatially separated information streams and, therefore, enable improved network throughput and connectivity both in uplink and downlink transmissions. Traditionally, to efficiently facilitate such MIMO transmissions, linear base-station processing is adopted, that translates the MIMO channel into several single-antenna channels. Still, while such approaches are relatively easy to implement, they can leave on the table a significant amount of unexploited MIMO capacity. …
Reducing computational complexity is crucial in optimizing the phase shifts of Intelligent Reflecting Surface (IRS) systems since IRS-assisted communication systems are generally deployed with a large number of reflecting elements (REs). This letter proposes a low-complexity algorithm, designated as Dimension-wise Sinusoidal Maximization (DSM), to obtain the optimal IRS phase shifts that maximize the sum capacity of a MIMO network. The algorithm exploits the fact that the objective function for the optimization problem is sinusoidal w.r.t. the phase shift of each RE. The numerical results show…
Multiple-input multiple-output (MIMO) millimeter wave (mmWave) communication is a key technology for next generation wireless networks. One of the consequences of utilizing a large number of antennas with an increased bandwidth is that array steering vectors vary among different subcarriers. Due to this effect, known as beam squint, the conventional channel model is no longer applicable for mmWave massive MIMO systems. In this paper, we study channel estimation under the resulting non-standard model. To that aim, we first analyze the beam squint effect from an array signal processing perspecti…
Next generation wireless base stations and access points will transmit and receive using extremely massive numbers of antennas. A promising technology for realizing such massive arrays in a dynamically controllable and scalable manner with reduced cost and power consumption utilizes surfaces of radiating metamaterial elements, known as metasurfaces. To date, metasurfaces are mainly considered in the context of wireless communications as passive reflecting devices, aiding conventional transceivers in shaping the propagation environment. This article presents an alternative application of metasu…
Cellular communication is a widely used technology in the world where the coverage area is divided into multiple cells. Interference is one of the most important challenges in cellular networks which causes problems by reducing the quality of the service. Cell-Free (CF) massive multiple-input multiple-output (MIMO) is a novel technolgy in which a large number of distributed access points (APs) are concurrently serving a small number of user equipment (UE). CF network can be an alternative technology to cellular networks for reducing interference. A challenging task in a CF network is scalabili…
Standards and Mobility Innovation Lab（标准与移动创新实验室）；Samsung Research America（三星美国研究院）
In multiple-input multiple-output (MIMO) systems, the high-resolution channel information (CSI) is required at the base station (BS) to ensure optimal performance, especially in the case of multi-user MIMO (MU-MIMO) systems. In the absence of channel reciprocity in frequency division duplex (FDD) systems, the user needs to send the CSI to the BS. Often the large overhead associated with this CSI feedback in FDD systems becomes the bottleneck in improving the system performance. In this paper, we propose an AI-based CSI feedback based on an auto-encoder architecture that encodes the CSI at UE i…
