arXivDaily arXiv每日学术速递 周一至周五更新
arXiv 1407.6669astro-ph.IM
收藏

GRAVITY计量系统:在optical fibers中建模计量

The GRAVITY metrology system: modeling a metrology in optical fibers

N. Blind, H. Huber, F. Eisenhauer, J. Weber, S. Gillessen, M. Lippa, L. Burtscher, O. Hans, M. Haug, F. Haussmann, S. Huber, A. Janssen, S. Kellner, Y. Kok, T. … 展开作者

N. Blind, H. Huber, F. Eisenhauer, J. Weber, S. Gillessen, M. Lippa, L. Burtscher, O. Hans, M. Haug, F. Haussmann, S. Huber, A. Janssen, S. Kellner, Y. Kok, T. Ott, O. Pfuhl, E. Sturm, E. Wieprecht, A. Amorim, W. Brandner, G. Perrin, K. Perraut, C. Straubmeier

摘要:

GRAVITY是第二代VLT干涉仪(VLTI),用于高精度窄角天体测量和相位参考干涉成像。重力的激光计量系统是其天体测量模式的核心,必须以10微弧秒的精度测量两颗恒星的距离。这意味着计量必须测量重力的两个光束组合器之间的光程差到5 nm的水平。计量设计呈现了一些非公共路径,因此必须稳定在1 nm的水平。否则会影响重力的性能。我们过去对原型进行的各种测试为我们提供了有关导致此错误的组件以及它们各自对总错误的贡献的提示。然而,仅从OPD测量难以评估它们的确切来源,因此难以提出解决该问题的方案。在本文中,我们提出了半经验建模的纤维计量系统的结果,依赖于理论基础,以及对表征的关键部件。计量系统关于各种效应的建模,例如,温度、波导加热或机械应力的测量将帮助我们理解计量学的行为。该建模的目标是:1)对测试设置进行建模并再现测量结果(作为建模的验证),2)确定非公共路径误差的来源,以及3)对当前计量设计提出修改,以达到所需的1nm稳定性。

英文摘要:

GRAVITY is the second generation VLT Interferometer (VLTI) instrument for high-precision narrow-angle astrometry and phase-referenced interferometric imaging. The laser metrology system of GRAVITY is at the heart of its astrometric mode, which must measure the distance of 2 stars with a precision of 10 micro-arcseconds. This means the metrology has to measure the optical path difference between the two beam combiners of GRAVITY to a level of 5 nm. The metrology design presents some non-common paths that have consequently to be stable at a level of 1 nm. Otherwise they would impact the performance of GRAVITY. The various tests we made in the past on the prototype give us hints on the components responsible for this error, and on their respective contribution to the total error. It is however difficult to assess their exact origin from only OPD measurements, and therefore, to propose a solution to this problem. In this paper, we present the results of a semi-empirical modeling of the fibered metrology system, relying on theoretical basis, as well as on characterisations of key components. The modeling of the metrology system regarding various effects, e.g., temperature, waveguide heating or mechanical stress, will help us to understand how the metrology behave. The goals of this modeling are to 1) model the test set-ups and reproduce the measurements (as a validation of the modeling), 2) determine the origin of the non-common path errors, and 3) propose modifications to the current metrology design to reach the required 1nm stability.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑