A high reflectivity and polarization selective high contrast grating mirror has been designed with the use of an automated optimization algorithm. Through a precise study of the tolerance of the different lengths of the structure, the robustness with respect to the fabrication errors has been enhanced to high tolerance values between 5 % and 210 %. This adjustment of the dimensions of the structure leads to a 250 nm large bandwidth mirror well adapted for a VCSEL application at λ= 2.65 $μ$m and can easily be scaled for other wavelengths.
A Si/Si3N4 high contrast grating mirror has been designed for a VCSEL integration in mid-infrared (λ = 2.65 $μ$m). The use of an optimization algorithm which maximizes a VCSEL mirror quality factor allowed the adjustment of the grating parameters while keeping large and shallow grating pattern. The robustness with respect to fabrication error has been enhanced thanks to a precise study of the grating dimension tolerances. The final mirror exhibits large high reflectivity bandwidth with a polarization selectivity and several percent of tolerance on the grating dimensions.
We present a method to analyse the coupling of lateral displacements in nanoscale structures, in particular waveguide grating mirrors (WGM), into the phase of a reflected Gaussian beam using a finite-difference time-domain simulation. Such phase noise is of interest for using WGMs in high-precision interferometry. We show that WGMs do not couple lateral displacements into the phase of a reflected beam to a precision of 10^{-7} rad and that WGMs are therefore not subject to the same stringent alignment requirements as previously proposed layouts using diffraction gratings.
We report on the first demonstration of a fully suspended 10m Fabry-Perot cavity incorporating a waveguide grating as the coupling mirror. The cavity was kept on resonance by reading out the length fluctuations via the Pound-Drever-Hall method and employing feedback to the laser frequency. From the achieved finesse of 790 the grating reflectivity was determined to exceed 99.2% at the laser wavelength of 1064\,nm, which is in good agreement with rigorous simulations. Our waveguide grating design was based on tantala and fused silica and included a ~20nm thin etch stop layer made of Al2O3 that a…
High polarization selective Si/SiO2 mid-infrared sub-wavelength grating mirrors with large bandwidth adapted to VCSEL integration are compared. These mirrors have been automatically designed for operation at λ= 2.3 $μ$m by an optimization algorithm which maximizes a specially defined quality factor. Several technological constraints in relation with the grating manufacturing process have been imposed within the optimization algorithm and their impact on the optical properties of the mirror have been evaluated. Furthermore, through the tolerance computation of the different dimensions of the st…
A GaAs/AlOx high contrast grating structure design which exhibits a 99.5% high reflectivity for a 425nm large bandwidth is reported. The high contrast grating (HCG) structure has been designed in order to enhance the properties of mid-infrared VCSEL devices by replacing the top Bragg mirror of the cavity. A robust optimization algorithm has been implemented to design the HCG structure not only as an efficient mirror but also as a robust structure against the imperfections of fabrication. The design method presented here can be easily adapted for other HCG applications at different wavelengths.
We demonstrate a "membrane in the middle" optomechanical system using a silicon nitride membrane patterned as a subwavelength grating. The grating has a reflectivity of over 99.8%, effectively creating two sub-cavities, with free spectral ranges of 6 GHz, optically coupled via photon tunneling. Measurements of the transmission and reflection spectra show an avoided crossing where the two sub-cavities simultaneously come into resonance, with a frequency splitting of 54 MHz. We derive expressions for the lineshapes of the symmetric and antisymmetric modes at the avoided crossing, and infer the g…
The large transparency window of silicon, covering the 1.1 um 8 um wavelength range, makes it a promising platform for the implementation of photothermal-based absorption spectrometers. These devices indirectly sense absorption in the mid-infrared (MIR) by using near-infrared (NIR) wavelengths, thereby enabling the realization of MIR absorption spectrometers without the need for MIR photodetectors. Nevertheless, due to their comparatively large index contrast and cross-sections, MIR Si strip waveguides are multi-mode at NIR wavelengths, hindering device implementation. Here we present, for the…
We introduce a simple and practical method to create ultrashort intense optical vortices for applications involving high-intensity lasers. Our method utilizes femtosecond laser pulses to laser-etch grating lines into laser-quality gold mirrors. These grating lines holographically encode an optical vortex. We derive mathematical equations for each individual grating line to be etched, for any desired (integer) topological charge. We investigate the smoothness of the etched grooves. We show that they are smooth enough to produce optical vortices with an intensity that is only a few percent lower…
We propose a degenerate version of the Bragg condition, associated to a degenerate band edge (DBE). A standard Bragg condition can be implemented using a periodic grating that operates at the regular band edge. The structure we propose to realize a DBE is made of two stacked identical gratings that form two coupled periodic waveguides with broken mirror symmetry. The occurrence of the DBE is verified by using both an eigenmode solver and the calculations of scattering parameters, using full-wave simulations. The proposed structure is a good candidate to conceive a degenerate distributed feedba…
The inscription of Bragg gratings in chalcogenide (As2Se3) wires with sub-wavelength diameter is proposed and demonstrated. A modified transverse holographic method employing He Ne laser light at a wavelength of λw = 633 nm allows the writing of Bragg grating reflectors in the 1550 nm band. The gratings reach an extinction ratio of 40 dB in transmission and a negative photo-induced index change of δn~0.01. The inscription of Bragg gratings in chalcogenide microwires will enable the fabrication of new devices with applications in nonlinear optics, and sensing in the near-to-mid-infrared region …
Mid-infrared (mid-IR) spectroscopy is a crucial workhorse for a plethora of analytical applications and is suitable for diverse materials, including gases, polymers or biological tissue. However, this technologically significant wavelength regime between 2.5-10$μ$m suffers from technical limitations primarily related to the large noise in mid-IR detectors and the complexity and cost of bright, broadband mid-IR light sources. Here, using highly non-degenerate, broadband photon pairs from bright spontaneous parametric down-conversion (SPDC) in a nonlinear interferometer, we circumvent these limi…
The perfect absorption of light in subwavelength thickness layers generally relies on exotic materials, metamaterials or thick metallic gratings. Here we demonstrate that total light absorption can be achieved in ultra-thin gratings composed of conventional materials, including relatively weakly-absorbing semiconductors, which are compatible with optoelectronic applications such as photodetectors and optical modulators. We fabricate a 41 nm thick antimony sulphide grating structure that has a measured absorptance of A = 99.3% at a visible wavelength of 591 nm, in excellent agreement with theor…
Ultrafast light sources have become an indispensable tool to access and understand transient phenomenon in material science. However, a simple and easy-to-implement method for harmonic selection, with high transmission efficiency and pulse duration conservation, is still a challenge. Here we showcase and compare two approaches for selecting the desired harmonic from a high harmonic generation source while achieving the above goals. The first approach is the combination of extreme ultraviolet spherical mirrors with transmission filters and the second approach uses a normal-incidence spherical g…
Sub-wavelength dielectric gratings (SWG) have emerged recently as a promising alternative to distributed-Bragg-reflection (DBR) dielectric stacks for broadband, high-reflectivity filtering applications. A SWG structure composed of a single dielectric layer with the appropriate patterning can sometimes perform as well as thirty or forty dielectric DBR layers, while providing new functionalities such as polarization control and near-field amplification. In this paper, we introduce a remarkable property of grating mirrors that cannot be realized by their DBR counterpart: we show that a non-period…
We report on the optical characterization of an ultra-high diffraction efficiency grating in 1st order Littrow configuration. The apparatus used was an optical cavity built from the grating under investigation and an additional high reflection mirror. Measurement of the cavity finesse provided precise information about the grating's diffraction efficiency and its optical loss. We measured a finesse of 1580 from which we deduced a diffraction efficiency of (99.635$\pm$0.016)% and an overall optical loss due to scattering and absorption of just 0.185 %. Such high quality gratings, including the …
In this paper, the experimental demonstration of Echelle Grating multiplexers in generic thick Silicon technology, using metal reflectors, is reported. Two multiplexer designs are shown, covering the C-band and partially the S and L bands, with 4 and 8 channels respectively. The multiplexers exhibited performance similar to previously reported devices on dedicated manufacturing processes. The average figures measured are insertion loss 5 dB, loss non-uniformity 3 dB, polarization dependent loss 0.6 dB, polarization dependent wavelength shift of 0.3 nm, with reduced footprint. The performance c…
Structured illumination microscopy (SIM) achieves doubled spatial resolution by exciting the specimen with a high-contrast, high-frequency sinusoidal pattern. Such an excitation pattern can be generated by interference between multiple laser beams, which are diffracted from a grating. In SIM, 2D imaging requires 9 patterns and 3D imaging requires 15 patterns. Compared to mechanical movement of gratings, opti-electro devices provide rapid switch of the excitation patterns, in which Digital Micro-mirror Device (DMD) is most common in industry. Here we model DMD as the blazed grating and report a…
The presence of a pulse train structure of an oscillator-type free-electron laser (FEL) results in the immediate damage of a solid target upon focusing. We demonstrate that the laser-induced damage threshold can be significantly improved by gating the mid-infrared (MIR) FEL pulses with a plasma mirror. Although the switching pulses we employ have a nanosecond duration which does not guarantee the clean wavefront of the gated FEL pulses, the high focusablity is experimentally confirmed through the observation of spectral broadening by a factor of 2.1 when we tightly focus the gated FEL pulses o…
In this paper, we present a method for analysis of phase errors and power truncation in SiGe/Si graded index arrayed waveguide gratings (AWGs) operating in mid-infrared spectral range. Semi-analytical model used herein is based on Gaussian approximation of the modal field and Fourier Optics. This method is applied to study the correlation between crosstalk level, effective index deviation in array waveguides and power truncation in 3.4 micrometer, 4.5 micrometer, 5.7 micrometer and 7.6 micrometer central wavelength AWGs. We show that the impact of effective index variation is more critical for…
Simulation results, fabrication details and measurements are presented for a one dimensional aperture and grating array for the purpose of plasmonic beam shaping of the λ=3.99μm output of an optically pumped semiconductor laser.
Polaritons can provide strong optical field enhancement allowing to boost light-matter interaction. Here, we experimentally observe enhancement of mid-infrared second-harmonic generation (SHG) using grating-coupled surface phonon polaritons of the 6H-SiC surface. In our experiment, we measure the SHG along the polariton dispersion by changing the incidence angle of the excitation beam. We observe hybridization between the propagating surface phonon polaritons and localized plasmon resonances in the gold grating, evidenced by the modification of the polariton dispersion as we change the area ra…
One of the most serious bottleneck on achieving kilojoule-level high-energy petawatt (PW) to hundreds-petawatt (100PW) lasers with ps to fs pulse duration is the requirement of as large as meter-sized gratings in the compressor so as to avoid the laser-induced damage to the gratings. However, this kind of meter-sized grating with high quality is hard to manufacture so far. Here, we propose a new in-house beam-splitting compressor based on the property that the damage threshold of gratings depend on the pulse duration. The new scheme will simultaneously improve the stability, save expensive gra…
We propose and analyze an active mirror structure that uses a subwavelength grating reflector combined with optical gain. The structure is designed to be directly bonded to a thermal substrate (such as diamond) for efficient heat removal. We present optical wave propagation and thermal transport analysis and show that such a structure is well suited for power scaling of optically pumped semiconductor disk lasers to multi-kilowatt CW power operation.
We demonstrate micromechanical reflectors with a reflectivity as large as 99.4% and a mechanical quality factor Q as large as 7.8*10^5 for optomechanical applications. The reflectors are silicon nitride membranes patterned with sub-wavelength grating structures, obviating the need for the many dielectric layers used in conventional mirrors. We have employed the reflectors in the construction of a Fabry-Perot cavity with a finesse as high as F=1200, and used the optical response to probe the mechanical properties of the membrane. By driving the cavity with light detuned to the high-frequency si…
Topological photonic cavities based on dissimilar Bragg gratings
Universidad de Málaga（马拉加大学）；CNRS, Université Paris-Saclay（法国国家科学研究中心，巴黎萨克雷大学）；Adelaide University（阿德莱德大学）；National Research Council Canada（加拿大国家研究委员会）
In this paper, we demonstrate a domain inversion crystal structure to study the cascaded three-wave mixing process in a two peak Stark-chirped rapid adiabatic passage. We have achieved efficient wavelength conversion, which can be performed in intuitive order and counterintuitive order. The requirement of crystal is reduced and the flexibility of structure design is improved. When the conversion wavelength is fixed, increasing the coupling coefficient between the two peaks can reduce the intensity of the intermediate wavelength while maintaining high conversion efficiency. Compared with the ca…
The thermal emission of refractory plasmonic metamaterial - a titanium nitride 1D grating - is studied at high operating temperature (540 °C). By choosing a refractory material, we fabricate thermal gratings with high brightness that are emitting mid-infrared radiation centered around 3 $μ$m. We demonstrate experimentally that the thermal excitation of plasmon-polariton on the surface of the grating produces a well-collimated beam with a spatial coherence length of 32λ (angular divergence of 1.8°) which is quasi-monochromatic with a full width at half maximum of 70 nm. These experimental resul…
A new dielectric Fabry-Perot cavity was designed for a resonant enhancing optical absorption by a thin absorber layer embedded into the cavity. In this cavity, the front mirror is a subwavelength grating with $\sim 100$% retroreflection. For a HgCdTe absorber in a matching cavity of the new type, the design is shown to meet the combined challenges of increasing the absorbing efficiency of the entire device up to $\sim 100$% and reducing its size and overall complexity, compared to a conventional resonant cavity enhanced HgCdTe absorber, while maintaining a fairly good tolerance against the gra…
We demonstrate a new regime for mid-infrared optical parametric chirped pulse amplification (OPCPA) based on achromatic quasi-phase-matching. Our mid-infrared OPCPA system is based on collinear aperiodically poled lithium niobate (APPLN) pre-amplifiers and a non-collinear PPLN power amplifier. The idler output has a bandwidth of 800 nm centered at 3.4 $μ$m. After compression, we obtain a pulse duration of 44.2 fs and a pulse energy of 21.8 $μ$J at a repetition rate of 50 kHz. We explain the wide applicability of the non-collinear QPM amplification scheme we used, including how it can enable oc…
We designed and simulated freestanding dielectric optical metasurfaces based on arrays of etched nanoholes in a silicon membrane. We showed $2π$ phase control and high forward transmission at mid-infrared wavelengths by tuning the dimensions of the holes. We also identified the mechanisms responsible for high forward scattering efficiency and showed that these conditions are connected with the well-known Kerker conditions already proposed for isolated scatterers. A beam deflector was designed and optimized through sequential particle swarm and gradient descent optimization to maximize transmis…
We explore various models for the pattern forming instability in a laser-driven cloud of cold two-level atoms with a plane feedback mirror. Focus is on the combined treatment of nonlinear propagation in a diffractively thick medium and the boundary condition given by feedback. The combined presence of purely transverse transmission gratings and reflection gratings on wavelength scale is addressed. Different truncation levels of the Fourier expansion of the dielectric susceptibility in terms of these gratings are discussed and compared to literature. A formalism to calculate the exact solution …
The Rayleigh-Modal method is used to calculate the electromagnetic field within the grooves of a perfectly conducting, rectangular-shaped 1D diffraction grating. An \emph{enhancement coefficient} ($η$) is introduced in order to quantify such an energy concentration. Accordingly, $η>$1 means that the amount of electromagnetic energy present within the grooves is larger than that one will have, over the same volume, if the diffraction grating is replaced by a perfectly reflecting mirror. The results in this paper show that $η$ can be as large as several decades at certain, often narrow, ranges o…
We propose and demonstrate a simple route to few-optical-cycle pulse generation from a mid-infrared fiber laser through nonlinear compression of pulses from a holmium-doped fiber oscillator using a short length of chalcogenide fiber and a grating pair. Pulses from the oscillator with 265-fs duration at 2.86 μm are spectrally broadened through self-phase modulation in step-index As2S3 fiber to 141-nm bandwidth and then re-compressed to 70 fs (7.3 optical cycles). These are the shortest pulses from a mid-infrared fiber system to date, and we note that our system is compact, robust, and uses only…
We investigate the optical properties of microcavities with suspended subwavelength structured mirrors, such as high-contrast gratings or two-dimensional photonic crystals slabs, and focus in particular on the regime in which the microcavity free-spectral range is larger than the width of a Fano resonance of the highly reflecting structured mirror. In this unusual regime, the transmission spectrum of the microcavity essentially consists in a single mode, whose linewidth can be significantly narrower than both the Fano resonance linewidth and the linewidth of an equally short cavity without str…
Mid-infrared saturable absorber mirror is successfully fabricated by transferring the mechanically exfoliated black phosphorus onto the gold-coated mirror. With the as-prepared black phosphorus saturable absorber mirror, a continuous-wave passively mode-locked Er:ZBLAN fiber laser is demonstrated at the wavelength of 2.8 um, which delivers a maximum average output power of 613 mW, a repetition rate of 24 MHz and a pulse duration of 42 ps. To the best of our knowledge, it is the first time to demonstrate black phosphorus mode-locked laser at 2.8 um wavelength. Our results demonstrate the feasib…
As a fundamental optical approach to interferometry, Sagnac interference has been widely used for reflection manipulation, precision measurements, and spectral engineering in optical systems. Compared to other interferometry configurations, it offers attractive advantages by yielding a reduced system complexity without the need for phase control between different pathways, thus offering a high degree of stability against external disturbance and a low wavelength dependence. The advance of integration fabrication techniques has enabled chip-scale Sagnac interferometers with greatly reduced foot…
We experimentally demonstrate a simple configuration for mid-infrared (MIR) frequency comb generation in quasi-phase-matched lithium niobate waveguides using the cascaded-$χ^{(2)}$ nonlinearity. With nanojoule-scale pulses from an Er:fiber laser, we observe octave-spanning supercontinuum in the near-infrared with dispersive-wave generation in the 2.5--3 $\textμ$m region and intra-pulse difference-frequency generation in the 4--5 $\textμ$m region. By engineering the quasi-phase-matched grating profiles, tunable, narrow-band MIR and broadband MIR spectra are both observed in this geometry. Final…
We describe the design of a new family of high spectral brightness narrow linewidth (NLW) mid-infrared (MIR) lasers of < 1 MHz anticipated linewidths with potential for operation at any target wavelength between 2.5 and 9.5 um. More specifically, we analyze the potential performance characteristics of mid-infrared distributed feedback (DFB) Raman fiber lasers (RFLs) based on Pi-phase-shifted (PPS) Fiber Bragg Gratings (FBGs) written in appropriately chosen low-phonon-energy glass fibers. In particular, we calculate anticipated threshold pump powers for optimal laser designs and pump wavelength…
Highly directional radiation from photonic structures is important for many applications, including high power photonic crystal surface emitting lasers, grating couplers, and light detection and ranging devices. However, previous dielectric, few-layer designs only achieved moderate asymmetry ratios, and a fundamental understanding of bounds on asymmetric radiation from arbitrary structures is still lacking. Here, we show that breaking the 180$^\circ$ rotational symmetry of the structure is crucial for achieving highly asymmetric radiation. We develop a general temporal coupled-mode theory form…
Plasmonic-cavity Modulator for the Mid-IR with a Semi-transparent and Nonlinear Heavily-doped Semiconductor Mirror
Istituto Italiano di Tecnologia（意大利理工学院）；Istituto di Fotonica e Nanotecnologie, Consiglio Nazionale delle Ricerche（国家研究委员会光子和纳米技术研究所）；University of Luxembourg（卢森堡大学）；Institute for Advanced Studies, University of Luxembourg Campus Belval（卢森堡大学贝尔瓦尔校区高等研究院）；Centre de Nanosciences et de Nanotechnologies (C2N), CNRS UMR 9001, Universit´e Paris-Saclay（巴黎萨克雷大学CNRS 9001联合实验室纳米科学与纳米技术中心）
Optical surface waves, highly localized modes bound to the surface of media, enable manipulation of light at nanoscale, thus impacting a wide range of areas in nanoscience. By applying metamaterials, artificially designed optical materials, as contacting media at the interface, we can significantly ameliorate surface wave propagation and even generate new types of waves. Here, we demonstrate that high aspect ratio (1:20) grating structures with plasmonic lamellas in deep nanoscale trenches function as a versatile platform supporting both surface and volume infrared waves. The surface waves exh…
A few-micron thick structure that shows nearly 100% resonant polarized absorptance at a predefined midinfrared wavelength is designed and simulated. Like resonant-cavity enhanced photodetector structure, it contains a thin absorber enclosed in a dielectric cavity but surrogates the mirrors by two grating-on-layer structures. Fair manufacturing tolerance while maintaining high peak efficiency is proved. Electromagnetic fields amplitudes and Poynting vector over the cavity-absorber area are visualized and topology of electromagnetic power flow for two linear polarizations is discussed.
Recently High Electron Mobility Transistor (HEMT) inspired III-V electro-optic modulator topologies were proposed for realizing high speed electro-optic modulators leveraging plasma dispersion effect due to the 2D Electron Gas (2DEG) present at the III-V heterostructure interface. The 2DEG is highly confined at the interface, extending to very low depths in the bulk ($\approx$10nm) and therefore has limited spatial overlap with the optical mode. In this paper, we propose a novel modulator design to boost the 2DEG-light interaction, wherein the HEMT is embedded within a high contrast grating (H…
We demonstrate the optical coupling of two cavities without light transmission through a substrate. Compared to a conventional coupling component, that is a partially transmissive mirror, an all-reflective coupler avoids light absorption in the substrate and therefore associated thermal problems, and even allows the use of opaque materials with possibly favourable mechanical and thermal properties. Recently, the all-reflective coupling of two cavities with a low-efficiency 3-port diffraction grating was theoretically investigated. Such a grating has an additional (a third) port. However, it wa…
We present a comprehensive study of dispersion managed ultrashort-pulse generation in Nd-doped polarization maintaining all-fiber laser at a 920 nm wavelength. We implement a linear laser scheme with a chirped fiber Bragg grating (CFBG) serving as a semitransparent mirror and semiconductor saturable absorber mirror (SESAM) as a mode-locker and as a second non-transparent mirror. Complete 1064 nm emission filtering is ensured by 920/1064 wavelength division multiplexer. The dispersion compensation by CFBG was sufficient to reach anomalous net dispersion in the shortest laser scheme allowing us …
Asymptotic stability of laser-driven lightsails: Enhancement by optical dispersion engineering in gratings
The University of Sydney（悉尼大学）；School of Physics, The University of Sydney（悉尼大学物理学院）；Institute of Photonics and Optical Science, The University of Sydney（悉尼大学光子与光学科学研究所）；School of Electrical and Computer Engineering, The University of Sydney（悉尼大学电气与计算机工程学院）；The University of Sydney Nano Institute, The University of Sydney（悉尼大学纳米研究院）
We report on a long wavelength emitting rare earth doped fiber laser with emission centered at 3.5 μm and tunable across 450 nm. The longest wavelength emission was 3.78 μm, which is the longest emission from a fiber laser operating at room temperature. In a simple optical arrangement employing dielectric mirrors for feedback, the laser was capable of emitting 1.45 W of near diffraction limited output power at 3.47 μm. These emission characteristics compliment the emission from quantum cascade lasers and demonstrate how all infrared dual wavelength pumping can be used to access high lying rare…
We demonstrate an optical phased-array (OPA) equipped with a 3D-printed facet-attached element for shaping and deflection of the emitted beam. The beam shaper combines freeform refractive surfaces with total-internal-reflection (TIR) mirrors and is in-situ printed to edge-emitting waveguide facets using high-resolution multi-photon lithography, thereby ensuring precise alignment with respect to on-chip waveguide structures. In a proof-of-concept experiment, we achieve a grating-lobe free steering range of $\pm 30°$ and a full-width-halfmaximum (FWHM) beam divergence of approximately $2°$. The …
